Maytag BRAVOS MEDB200VQ0 Manuel utilisateur

Marque: Maytag

Modèle: BRAVOS MEDB200VQ0

Catégorie: Sèche-linge électriques

Taper: Manuel utilisateur

BRAVOS ® FABRIC

ELECTRIC

USE & CARE

CARE SYSTEM

DRYER

GUIDE

p p

SECHEUSE ELECTRIQUE BRAVOS ®

AVEC SYSTEME

DE SOIN DES TISSUS A LA VAPEUR

GUIDE D'UTILISATION ET D'ENTRETIEN

FOR QUESTIONS ABOUT FE,a(IURES, OPERATION/PERFORMANCE, PARTS, ACCESSORIES OR SERVICE

CAll: 1.800.688.9900

IN CANADA, CAll: 1.800.807.6777

VISIT OUR WEBSITE AT WWW.MAYTAG.COM

IN CANADA, WWW.MAYTAG.CA

AU CANADA, POUR ASSISTANCE, INSTAllATION OU SERVICE, COMPOSEZ IE : 1.800.807.6777

OU VISITEZ NOTRE SITE INTERNET ,_

WWW. M AYTAG. CA

W10201172A

,i_!_ii!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i_i_i_ii!i¸i!i!i!i!i!i!i!i_i_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_i_iiiiYiiiiii//li¸il¸iiii_ii,i_ii,i_ii,i_ii,i_ii,i_i_iii_i_ii_il'ii_i_iil'ii_i_iil_i_ii_i_ii_i_ii_ii_i_ii_:ii:_:i_:ii:_:i_:ii:_:i_:ii:_:i_:ii:_:i_:ii:_:i_:ii:_:i_:_i_::¸ _:iii!ii,l,ii_,,¸¸¸¸_!_iiiiiiiii_i_ ¸il¸ii_ii_ii¸I¸I¸il¸ii_ii¸ii_ii¸ii_ii¸ii_iil¸ii_i_iil¸I¸iiiii_iiiii_i_i_ii_i_iiiii_ii_iii_ii_iii_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii_!_!!

TABLE OF CONTENTS

DRYER SAFETY .......................................................................................................................... 3

INSTALLATION INSTRUCTIONS ............................................................................................. 4

Tools and Parts ....................................................................................................................... 4

I.ocation Requirements .......................................................................................................... 4

Electrical Requirements- U.S.A. Only .................................................................................... 5

Electrical Requirements - Canada Only .................................................................................. 7

Electrical Connection - U.S.A. Only ....................................................................................... 8

Venting Requirements .......................................................................................................... 14

Plan Vent System .................................................................................................................. 15

Install Vent System ............................................................................................................... 17

Install I_eveling I.egs ............................................................................................................. 17

Connect Vent ....................................................................................................................... 17

I.eve[ Dryer .......................................................................................................................... 18

Reverse Door Swing ............................................................................................................. 18

Complete Installation ........................................................................................................... 20

DRYER USE.............................................................................................................................. 21

Starting Your Dryer ............................................................................................................... 21

Stopping, Pausing, or Restarting ........................................................................................... 22

Drying and Cycle Tips .......................................................................................................... 22

Status I_ights .......................................................................................................................... 23

Cyc[es .................................................................................................................................. 23

Modifiers .............................................................................................................................. 24

Options ................................................................................................................................ 24

End Signal ............................................................................................................................ 25

Changing Cycles, Modifiers, and Options ............................................................................ 25

Drying Rack Option ............................................................................................................. 25

DRYER CARE ........................................................................................................................... 26

Cleaning the Dryer I.ocation ................................................................................................ 26

Cleaning the I_int Screen ...................................................................................................... 26

Cleaning the Dryer Interior ................................................................................................... 27

Removing Accumulated Lint ................................................................................................ 27

Vacation, Storage and Moving Care ..................................................................................... 27

TROUBLESHOOTING ............................................................................................................. 28

Dryer Operation ................................................................................................................... 28

Dryer Results ........................................................................................................................ 29

ASSISTANCE OR SERVICE ....................................................................................................... 30

In the U.S.A .......................................................................................................................... 30

In Canada ............................................................................................................................. 31

ACCESSORIES ......................................................................................................................... 31

WARRANTY ............................................................................................................................ 32

TABLE DES MATIERES

SI_CURITI_ DE LA SI_CHEUSE ................................................................................................... 33

INSTRUCTIONS D'INSTALLATION ....................................................................................... 35

Outillage et pi_ces ............................................................................................................... 35

E×igences d'emplacement .................................................................................................... 35

Sp6cifications 6lectriques - Pour le Canada seulement ......................................................... 36

Exigences concernant ['6vacuation ...................................................................................... 37

Planification du syst&me d'6vacuation ................................................................................. 39

Installation du syst&me d'6vacuation .................................................................................... 40

Installation des pieds de nivellement .................................................................................... 40

Raccordement du conduit d'6vacuation ............................................................................... 41

R6g[age de ['aplomb de [a s6cheuse ..................................................................................... 41

Inversion du sens d'ouverture de [a porte ............................................................................. 41

Achever ['installation ............................................................................................................ 44

UTILISATION DE LA SI_CHEUSE............................................................................................. 44

Mise en marche de [a s6cheuse ............................................................................................ 45

Arr&t, pause ou remise en marche ........................................................................................ 46

Conseils pour [e s6chage et [es programmes ........................................................................ 46

T6moins [umineux ................................................................................................................ 47

Programmes ......................................................................................................................... 47

Modificateurs ....................................................................................................................... 48

Options ................................................................................................................................ 49

End Signal (signal de fin de programme) .............................................................................. 49

Changement des programmes, modificateurs, et options ..................................................... 49

Option de grille de s6chage ................................................................................................. 50

ENTRETIEN DE LA SI_CHEUSE ................................................................................................ 51

Nettoyage de ['emplacement de [a s6cheuse ........................................................................ 51

Nettoyage du fi [tre _ charpie ................................................................................................ 51

Nettoyage de ['int6rieur de [a s6cheuse ................................................................................ 51

Retrait de [a charpie accumul6e ........................................................................................... 52

Pr6cautions _ prendre avant [es vacances, un entreposage ou un d6m6nagement ............... 52

DI_PANNAGE .......................................................................................................................... 52

Fonctionnement de [a s6cheuse ........................................................................................... 52

R6sultats de [a s6cheuse ....................................................................................................... 53

ASSISTANCE OU SERVICE ...................................................................................................... 55

Au Canada ........................................................................................................................... 55

ACCESSOIRES .......................................................................................................................... 55

GARANTIE ............................................................................................................................... 55

DRYER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNIN G: To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic precautions,

including the following:

[] Read all instructions before using the dryer.

[] Do not place items exposed to cooking oils in your dryer.

Items contaminated with cooking oils may contribute to

a chemical reaction that could cause a load to catch fire.

[] Do not dry articles that have been previously cleaned in,

washed in, soaked in, or spotted with gasoline, dry-

cleaning solvents, or other flammable or explosive

substances as they give off vapors that could ignite or

explode.

[] Do not allow children to play on or in the dryer. Close

supervision of children is necessary when the dryer is

used near children.

[] Before the dryer is removed from service or discarded,

remove the door to the drying compartment.

[] Do not reach into the dryer if the drum is moving.

[] Do not install or store the dryer where it will be exposed

to the weather.

[] Do not tamper with controls.

[] Do not repair or replace any part of the dryer or attempt

any servicing unless specifically recommended in this

Use and Care Guide or in published user-repair

instructions that you understand and have the skills to

carry out.

[] Do not use fabric softeners or products to eliminate static

unless recommended by the manufacturer of the fabric

softener or product.

[] Do not use heat to dry articles containing foam rubber or

similarly textured rubber-like materials.

[] Clean lint screen before or after each load.

[] Keep area around the exhaust opening and adjacent

surrounding areas free from the accumulation of lint, dust,

and dirt.

[] The interior of the dryer and exhaust vent should be

cleaned periodically by qualified service personnel.

[] See installation instructions for grounding requirements.

SAVE THESE INSTRUCTIONS

Gather the required tools and parts before starting

instructions provided with any tools listed here.

• Flat-blade screwdriver

• #2 Phillips screwdriver

• Adjustable wrench that opens to 1"

(2.5 cm) or hex-head socket wrench

(for adjusting dryer feet)

• Wire stripper (direct wire installations)

installation. Read and follow the

• Tin snips (new vent installations)

• I.evel

• Vent clamps

• Caulking gun and compound

(for installing new exhaust vent)

• Tape measure

Parts supplied:

Remove parts package from dryer drum. Check that all parts were included.

A. leveling legs (4)

Parts needed:

Check local codes. Check existing electrical supply and venting and see "Electrical

Requirements" and "Venting Requirements" before purchasing parts.

Mobile home installations require metal exhaust system hardware available for purchase from

the dealer from whom you purchased your dryer. For information on ordering, please refer to

the "Assistance or Service" section. You may also contact the dealer from whom you

purchased your dryer.

If using a power supply cord:

Use a UI. listed power supply cord kit marked for use with clothes dryers. The kit should

contain:

• A UI_ listed 30-amp power supply cord, rated 120/240 volt minimum. The cord should be

type SRI) or SRI)T and be at least 4 ft (1.22 m) long. The wires that connect to the dryer

must end in ring terminals or spade terminals with upturned ends.

• A UI. listed strain relief.

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Place dryer at least 18 inches (46 cm) above the floor

for a garage installation.

Failure to do so can result in death, explosion, or fire.

You will need

• A location that allows for proper exhaust installation. See "Venting Requirements."

• A separate 30-amp circuit.

• If you are using a power supply cord, a grounded electrical outlet located within

2 ft (61 cm) of either side of the dryer. See "Electrical Requirements."

• A sturdy floor to support the total weight (dryer and load) of 200 Ibs (90.7 kg). The

combined weight of a companion appliance should also be considered.

• A level floor with a maximum slope of 1" (2.5 cm) under entire dryer.

Do not operate your dryer at temperatures below 45°F (7°C). At lower temperatures, the dryer

might not shut off at the end of an automatic cycle. Drying times can be extended.

The dryer must not be installed or stored in an area where it will be exposed to water and/or

weather.

Check code requirements. Some codes limit, or do not permit, installation of the dryer in

garages, closets, mobile homes or sleeping quarters. Contact your local building inspector.

Installation Clearances

The location must be large enough to allow the dryer door to open fully.

Dryer Dimensions

*Most installations require a minimum 5" (12.7 cm) clearance behind the dryer for the

exhaust vent with elbow. See "Venting Requirements."

Installation spacing for recessed area or closet installation

The following spacing dimensions are recommended for this dryer. This dryer has been tested

for spacing of 0" (0 cm) clearance on the sides and rear. Recommended spacing should be

considered for the following reasons:

• Additional spacing should be considered for ease of installation and servicing.

• Additional clearances might be required for wall, door and floor moldings.

• Additional spacing should be considered on all sides of the dryer to reduce noise transfer.

• For closet installation, with a door, minimum ventilation openings in the top and bottom

of the door are required. I.ouvered doors with equivalent ventilation openings are

acceptable.

• Companion appliance spacing should also be considered.

• Additional spacing is required if you exhaust out the rear of the dryer to either the right or

[eft side.

I" _I _ m"-_I_I"

(2,5cm) (73.7crn} (2.5crn}

14"max.*

48in.2._

(310cm_)

24in.2*

(l,_®_

÷11"*t_27,/,"H5"

(2.5cm}(89.2crn}(12.7cm}

311,

(7.6cm)

A. Recessed area

B. Side view - closet or confined area

C. Closet door with vents

*Required spacing

Mobile home - Additional installation requirements

This dryer is suitable for mobile home installations. The installation must conform to the

Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the

Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280) or

Standard CAN/CSA-Z240 MH.

Mobile home installations require:

• Metal exhaust system hardware, which is available for purchase from your dealer.

• Special provisions must be made in mobile homes to introduce outside air into the dryer.

The opening (such as a nearby window) should be at [east twice as large as the dryer

exhaust opening.

It is your responsibility

• To contact a qualified electrical installer.

• To be sure that the electrical connection is adequate and in conformance with the

National Electrical Code, ANSI/NFPA 70-latest edition and all local codes and

ordinances.

The National Electric Code requires a 4-wire power supply connection for homes built

after 1996, dryer circuits involved in remodeling after 1996, and all mobile home

installations.

A copy of the above code standards can be obtained from: National Fire Protection

Association, One Batterymarch Park, Quincy, MA 02269.

To supply the required 3 or 4 wire, single phase, 120/240 volt, 60 Hz., AC only electrical

supply (or 3 or 4 wire, 120/208 volt electrical sup@y, if specified on the serial/rating @ate)

on a separate 30-amp circuit, fused on both sides of the line. A time-delay fuse or circuit

breaker is recommended. Connect to an individual branch circuit. Do not have a fuse in

the neutral or grounding circuit.

• If codes permit and a separate ground wire is used, it is recommended that a qualified

electrician determine that the ground path is adequate.

Electrical Connection

To properly install your dryer, you must determine the type of electrical connection you will

be using and follow the instructions provided for it here.

• This dryer is manufactured ready to install with a 3-wire electrical supply connection. The

neutral ground conductor is permanently connected to the neutral conductor (white wire)

within the dryen If the dryer is installed with a 4-wire electrical supply connection, the

neutral ground conductor must be removed from the external ground connector (green

screw), and secured under the neutral terminal (center or white wire) of the terminal

block. When the neutral ground conductor is secured under the neutral terminal (center

or white wire) of the terminal block, the dryer cabinet is isolated from the neutral

conducton

• If local codes do not permit the connection of a neutral ground wire to the neutral wire,

see "Optional 3-wire connection" in "Electrical Connection - U.S.A. Only" section.

• Do not use an extension cord.

• • At[east5ft(1.52m)long.A4-wirepowersupplyconnectionmustbeusedwhentheapplianceisinstalledina

locationwheregroundingthroughtheneutralconductorisprohibited.Grounding

throughtheneutralisprohibitedfor(1)newbranch-circuitinstallations,(2)mobile

homes,(3)recreationalvehicles,and(4)areaswherelocalcodesprohibitgrounding

throughtheneutralconductors.

Ifusing a power supply cord:

Use a UI. listed power supply cord kit marked for use with clothes dryers. The kit should

contain:

• A UI_ listed 30-amp power supply cord, rated 120/240 volt minimum. The cord should be

type SRI) or SRI)T and be at least 4 ft (1.22 m) long. The wires that connect to the dryer

must end in ring terminals or spade terminals with upturned ends.

• A UI. listed strain relief.

If your outlet looks like this:

4-wire receptacle (14-30R)

Then choose a 4-wire power supply cord with ring or spade terminals and UI_ listed strain

relief. The 4-wire power supply cord, at least 4 ft (1.22 m) long, must have four 10-gauge

copper wires and match a 4-wire receptacle of N EMA Type 14-30R. The ground wire (ground

conductor) may be either green or bare. The neutral conductor must be identified by a white

cover.

If your outlet looks like this:

3-wire receptacle (lO-30R)

Then choose a 3-wire power supply cord with ring or spade terminals and UI. listed strain

relief. The 3-wire power supply cord, at least 4 ft (1.22 m) long, must have three 10-gauge

copper wires and match a 3-wire receptacle of NEMA Type 10-30R.

If connecting by direct wire:

Power supply cable must match power supply (4-wire or 3-wire) and be:

• Flexible armored cable or nonmetallic sheathed copper cable (with ground wire),

protected with flexible metallic conduit. All current-carrying wires must be insulated.

• 10-gauge solid copper wire (do not use aluminum).

GROUNDING INSTRUCTIONS

[] For a grounded, cord-connected dryer:

This dryer must be grounded, in the event of malfunction or

breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current.

This dryer uses a cord having an equipment-grounding

conductor and a grounding plug. The plug must be plugged

into an appropriate outlet that is properly installed and

grounded in accordance with all local codes and ordinances.

[] For a permanently connected dryer:

This dryer must be connected to a grounded metal,

permanent wiring system, or an equipment-grounding

conductor must be run with the circuit conductors and

connected to the equipment-grounding terminal or lead on

the dryer.

WARNING: improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative

or personnel if you are in doubt as to whether the dryer is

properly grounded. Do not modify the plug on the power

supply cord: if it will not fit the outlet, have a proper outlet

installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

_,0_,<_.04__'_<dt_ __J_c _ _",'s...._ _,_ _9_ 7

Electrical Shock Hazard

Plug into a grounded 4 prong outlet.

Failure to do so can result in death or electrical shock.

It is your responsibility

• To contact a qualified electrical installer.

To be sure that the electrical connection is adequate and in conformance with the

Canadian Electrical Code, C22.1-[atest edition and all local codes. A copy of the above

codes standard may be obtained from: Canadian Standards Association, 178 Rexda[e

Blvd., Toronto, ON M9W 1R3 CANADA.

To supply the required 4 wire, single phase, 120/240 volt, 60 Hz., AC only electrical

supply on a separate 30-amp circuit fused on both sides of the line. A time-delay fuse or

circuit breaker is recommended. Connect to an individual branch circuit

This dryer is equipped with a CSA International Certified Power Cord intended to be

plugged into a standard 14-30R wall receptacle. The cord is 5 ft (1.52 m) in length. Be

sure wall receptacle is within reach of dryer's final location.

If you are using a replacement power supply cord, it is recommended that you use Power

Supply Cord Replacement Part Number 3394208. For further information, please reference

the service numbers located in the "Assistance or Service" section.

GROUNDING INSTRUCTIONS

m For a grounded, cord-connected dryer:

This dryer must be grounded, in the event of malfunction or

breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current.

This dryer is equipped with a cord having an equipment-

grounding conductor and a grounding plug. The plug must

be plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local codes

and ordinances.

WARNING: improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative

or personnel if you are in doubt as to whether the dryer is

properly grounded. Do not modify the plug provided with the

dryer: if it will not fit the outlet, have a proper outlet installed

by a qualified electrician.

SAVE THESE INSTRUCTIONS

4-wire receptacle 14-30R

• Do not use an extension cord.

_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;_;:::;_7 ¸

EII](]YFIQII (}I [I.;(iil.l B - _._0o0_ _.o'_,_,=I} 7

I>II!_I_ZI II_II

Power Supply Cord Direct Wire

Fire Hazard

Use a new UL listed 30 amp power supply cord.

Use a UL listed strain relief.

Disconnect power before making electrical connections.

Connect neutral wire (white or center wire) to center

terminal (silver).

Ground wire (green or bare wire) must be connected to

green ground connector.

Connect remaining 2 supply wires to remaining

2 terminals (gold).

Securely tighten all electrical connections.

Failure to do so can result in death, fire, or

electrical shock.

Fire Hazard

Use 10 gauge sold copper wire.

Use a UL listed strain relief.

Disconnect power before making electrical connections.

Connect neutral wire (white or center wire) to center

terminal (silver).

Ground wire (green or bare wire) must be connected to

green ground connector.

Connect remaining 2 supply wires to remaining

2 terminals (gold).

Securely tighten al electrical connections.

Failure to do so can result in death, fire, or

electrical shock.

Style 1: Power supply cord strain relief1. Disconnect power.

2. Remove the hold-down screw and terminal block cover.

AB C D

A. Terminal block cover

B. HoM-down screw location

C. External ground conductor

screw

D. Centel, silver-colored

terminal block screw

E. Neutral ground wire

£ Hole below terminal block

opening

3. Install strain relief.

Remove the screws from a s/4" (1.9 cm) UI_ listed strain relief (UL marking on strain relief).

Put the tabs of the two clamp sections into the hole below the terminal block opening so

that one tab is pointing up and the other is pointing down, and hold in place. Tighten

strain relief screws just enough to hold the two clamp sections together.

: ....;................................/ ............................................A

A. Strain relief tab pointing up

B.Hole below terminal[)lockopening

C.Clamp section

D. Strainrelief tabpointing down

Put power supply cord through the strain relief. Be sure that the wire insulation on the

power supply cord is inside the strain relief. The strain relief should have a tight fit with

the dryer cabinet and be in a horizontal position. I)o not further tighten strain relief

screws at this point.

Style 2: Direct wire strain relief

Unscrew the removable conduit connector and any screws from a %" (1.9 cm) UI. listed

strain relief (UI_ marking on strain relief). Put the threaded section of the strain relief

through the hole below the terminal block opening. Reaching inside the terminal block

opening, screw the removable conduit connector onto the strain relief threads.

!..........j

................................. C

A. Removable conduit connector

B. Hole below terminal block opening

C. Strain relief threads

Put direct wire cable through the strain relief. The strain relief should have a tight fit with

the dryer cabinet and be in a horizontal position. Tighten strain relief screw against the

direct wire cable.

4. Now complete installation following instructions for your type of electrical connection:

4-wire (recommended)

3-wire (if 4-wire is not available)

Electrical Connection Options

If your home has: And you will be Go to Section:

connecting to:

4-wire receptacle

(N EMA type 14-30R)

4-wire direct

(12.7 cm)

A UL listed,

120/240-volt minimum,

30-amp, dryer power

supply cord*

A fused disconnect or

circuit breaker box*

4-wire connection:

Power Supply Cord

4-wire connection:

I)i rect Wi re

3-wire receptacle

(NEMA type 10-30R)

A UL listed,

120/240-volt minimum,

30-amp, dryer power

supply cord*

3-wire connection:

Power Supply Cord

3-wire direct A fused disconnect or 3-wire connection:

circuit breaker box* I)irect Wire

*If local codes do not permit the connection of a cabinet-ground conductor to the neutral

wire, go to "Optional 3-wire connection" section.

4-wire connection: Power supply cord

IMPORTANT: A 4-wire connection is required for mobile homes and where local codes do

not permit the use of 3-wire connections.

A_....._ B

C D E G

A. 4-wire receptacle (NEMA type 14-30R)

B.4-prong plug

C. Cround prong

D. Neutral prong

E.Spade terminals with upturned ends

I] 3/4" (1.9 cm) UL listed strain relief

C. Ring terminals

Remove center silver-colored terminal block screw.

Remove neutral ground wire from external ground conductor screw. Connect neutral

ground wire and the neutral wire (white or center wire) of power supply cord under

center, silver-colored terminal block screw. Tighten screw.

A. Neutral ground wire

B. External ground conductor screw - Dotted fine shows position

of NLUTRAL ground wire before being moved to center silver-

colored terminal block screw.

C. Center silver-colored terminal bkJck screw

D. Neutral wire (white or center wire)

E. Y4" ( 1.9 cm) UL listed strain relief

Connect ground wire (green or bare) of power supply cord to external ground conductor

screw. Tighten screw.

A. External ground conductor screw

B. Neutral ground wire

C. Cround wire (green or bare) of power supply cord

D. Y4" ( 1.9 cm) UL fisted strain refief

E. Center silver-colored terminal block screw

f: Neutral wire (white or center wire)

4. Connect the other wires to outer terminal block screws. Tighten screws.

! !

5. Tighten strain relief screws.

6. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-

down screw.

7. You have completed your electrical connection. Now go to "Venting Requirements."

I 0

4-wire connection: Direct Wire

IMPORTANT: A 4-wire connection is required for mobile homes and where local codes do

not permit the use of 3 wire connections.

Direct wire cable must have 5 ft (1.52 m) of extra length so dryer can be moved if needed.

Strip 5" (12.7 cm) of outer covering from end of cable, leaving bare ground wire at

5" (12.7 cm). Cut 1V2" (3.8 cm) from 3 remaining wires. Strip insulation back 1" (2.5 cm).

Shape ends of wires into a hook shape.

_:_,:....-_....

When connecting to the terminal block, place the hooked end of the wire under the screw of

the terminal block (hook facing right), squeeze hooked end together and tighten screw, as

shown.

1. Remove center silver-colored terminal block screw.

Remove neutral ground wire from external ground conductor screw. Connect neutral

ground wire and place the hooked end (hook facing right) of the neutral wire (white or

center wire) of direct wire cable under the center screw of the terminal block. Squeeze

hooked ends together. Tighten screw.

A ....... _ ................

A. Neutral ground wire

B. Fxternal ground conductor screw - Dotted fine shows

position of NLUTRAL ground wire before being moved to

center silver-colored terminal block screw.

C. Center silver-colored terminal block screw

D. Neutral wire (white or center wire)

E. Y4" ( 1.9 cm) UL listed strain relief

3. Connect ground wire (green or bare) of direct wire cable to external ground conductor

screw. Tighten screw. 3-wire connection: Power supply cord

A. External ground conductor screw

B. Neutral ground wire

C. Ground wire (green or bare) of power supply cord

D. %" (1.9 cm) UL fisted strain refief

£. Center silver-colored terminal block screw

£ Neuu'a] wire (white or center wire)

Place the hooked ends of the other direct wire cable wires under the outer terminal block

screws (hooks facing right). Squeeze hooked ends together. Tighten screws.

!! !!

5. Tighten strain relief screw.

6. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-

down screw.

7. You have completed your electrical connection. Now go to "Venting Requirements."

Use where local codes permit connecting cabinet-ground conductor to neutral wire.

C G F

A. 3-wire receptacle (NEMA type lO-30R)

B. 3-wire plug

C. Neutral prong

D. Spade terminals with upturned ends

£. V4" ( 1.9 cm) UL listed strain relief

£ Ring terminals

C. Neutra] wire (white or center wire)

1. I.oosen or remove center silver-colored terminal block screw.

2. Connect neutral wire (white or center wire) of power supply cord to the center, silver-

colored terminal screw of the terminal block. Tighten screw.

A. External ground conductor screw

B. Neutral ground wire

C. Center silver-colored terminal block screw

D. Neutral wire (white or center wire)

£. V4" ( 1.9 cm) UL listed strain relief

3. Connecttheotherwirestoouterterminalblockscrews.Tightenscrews.

3-wire connection: Direct Wire

Tighten strain relief screws.

Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-

down screw.

You have completed your electrical connection. Now go to "Venting Requirements."

Use where local codes permit connecting cabinet-ground conductor to neutral wire.

Direct wire cable must have 5 ft (1.52 m) of extra length so dryer can be moved if needed.

Strip 31/2'' (8.9 cm) of outer covering from end of cable. Strip insulation back 1" (2.5 cm). If

using 3-wire cable with ground wire, cut bare wire even with outer covering. Shape ends of

wires into a hook shape.

When connecting to the terminal block, place the hooked end of the wire under the screw of

the terminal block (hook facing right), squeeze hooked end together and tighten screw, as

shown.

1. I.oosen or remove center silver-colored terminal block screw.

Place the hooked end of the neutral wire (white or center wire) of direct wire cable under

the center screw of terminal block (hook facing right). Squeeze hooked end together.

Tighten screw.

f_ ....... C

A. fxtemal ground conductor screw

B. Neutral ground wire

C. Center siher-colored terminal block screw

D. Neutral wire (white or center wire)

£. 3/4" ( 1.9 cm) UL listed strain relief

Place the hooked ends of the other direct wire cable wires under the outer terminal block

screws (hooks facing right). Squeeze hooked ends together. Tighten screws.

!I !!

4. Tighten strain relief screw.

5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-

down screw.

6. You have completed your electrical connection. Now go to "Venting Requirements."

Optional 3-wire connection

Use for direct wire or power supply cord where local codes do not permit connecting

cabinet-ground conductor to neutral wire.

1. Remove center silver-colored terminal block screw.

2. Remove neutral ground wire from external ground conductor screw. Connect neutral

ground wire and the neutral wire (white or center wire) of power supply cord/cable under

center, silver-colored terminal block screw. Tighten screw.

A. External ground conductor screw

B. Neutral ground wire

C. Center silver-colored terminal block screw

D. Neutra/ wire (white or center wire)

E. 3/4" ( !.9 cm) UL fisted strain refief

£ Crounding path determined by a quafified electrician

Connect the other wires to outer terminal block screws. Tighten screws.

!! !!

4. Tighten strain relief screws.

5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-

down screw.

Connect a separate copper ground wire from the external ground conductor screw to an

adequate ground.

Fire Hazard

Use a heavy metal vent.

Do not use a plastic vent.

Do not use a metal foil vent.

Failure to follow these instructions can result in death

or fire.

WARN I NG: To reduce the risk of fire, this dryer MUST BE EXHAUSTED OUTDOORS.

IMPORTANT: Observe all governing codes and ordinances.

The dryer exhaust must not be connected into any gas vent, chimney, wall, ceiling or a

concealed space of a building.

If using an existing vent system

• Clean lint from the entire length of the system and make sure exhaust hood is not plugged

with lint.

• Replace any plastic or metal foil vent with rigid or flexible heavy metal vent.

• Review Vent system chart. Modify existing vent system if necessary to achieve the best

drying performance.

If this is a new vent system

Vent material

• Use a heavy metal vent. I)o not use plastic or metal foil vent.

• 4" (1 0.2 cm) heavy metal exhaust vent and clamps must be used.

4" ( 10.2 cm) heavy metal exhaust vent

Vent products can be purchased from your dealer or by calling Maytag Services. For more

information, see the "Assistance or Service" section.

Rigid metal vent

• For best drying performance, rigid metal vents are recommended.

• Rigid metal vent is recommended to avoid crushing and kinking.

Flexible metal vent

• Flexible metal vents are acceptable only if accessible for cleaning.

• Flexible metal vent must be fully extended and supported when the dryer is in its final

location.

• Remove excess flexible metal vent to avoid sagging and kinking that may result in

reduced airflow and poor performance.

• Do not install flexible metal vent in enclosed walls, ceilings or floors.

Elbows

45 ° elbows provide better airflow than 90 ° elbows.

Clamps

Good

Better

Use clamps to seal all joints.

Exhaust vent must not be connected or secured with screws or other fastening devices

that extend into the interior of the duct. Do not use duct tape.

Clamp

Exhaust

Recommended hood styles are shown here.

(10.2 cm)

A. Louvered hood style

B. Box hood style

The angled hood style (shown here) is acceptable.

(6.4 cm)

An exhaust hood should cap the vent to keep rodents and insects from entering the home.

Exhaust hood must be at least 12" (30.5 cm) from the ground or any object that may be in

the path of the exhaust (such as flowers rocks or bushes, snow line, etc.).

Do not use an exhaust hood with a magnetic latch.

improper venting can cause moisture and lint to collect

indoors, which may result in:

[] Moisture damage to woodwork, furniture, paint, wallpaper,

carpets, etc.

[] Housecleaning problems and health problems.

Choose your exhaust installation type

Recommended exhaust installations

Typical installations vent the dryer from the rear of the dryer.

A. Dryer

B. flbow

C. Waft

D. fxhaust hood

[T G

E. Clamps

£ Rigid metal or flexible metal vent

G. Vent length necessary to connect elbows

H. Exhaust out/et

Optional exhaust installations

Venting systems come in many varieties. Select the type best for your installation.

Fire Hazard

Cover unused exhaust hole with the following kit:

8212503

Contact your local dealer.

Failure to follow these instructions can result in death,

fire, electrical shock, or serious injury.

This dryer can be converted to exhaust out the bottom. If you prefer, you may contact your

local dealer to have the dryer converted.

This dryer can also be exhausted from the rear to either the right or left side. Optional kits for

these exhaust installations are needed. Refer to the manufacturer's instructions for kit

installation instructions.

A B

A. Standard rear offset exhaust installation

B. Rear exhaust installation to the right or left side

C D

C. Bottom exhaust installtion

D. Over-the-top installation (also available with

one offset elbow)

NOTE: The following kits for close clearance alternate installations are available for purchase.

Please see the "Assistance or Service" section to order.

• Over-the-Top Installation:

Part Number 4396028

• Periscope Installation (For use with dryer vent to wall vent mismatch):

Part Number 4396037 - 0" (0 cm) to 18" (45.72 cm) mismatch

Part Number 4396011 - 18" (45.72 cm) to 29" (73.66 cm) mismatch

Part Number 4396014 - 29" (73.66 cm) to 50" (127 cm) mismatch

• Rear exhaust installation to [eft or right side:

Part Number 4396011

• Vent extension:

Part Number 8544761

• Bottom Exhaust:

Part Number 8212503

Special provisions for mobile home installations

The exhaust vent must be securely fastened to a noncombustible portion of the mobile home

structure and must not terminate beneath the mobile home. Terminate the exhaust vent

outside.

Determine vent path

• Select the route that will provide the straightest and most direct path outdoors.

• Plan the installation to use the fewest number of elbows and turns.

• When using elbows or making turns, allow as much room as possible.

• Bend vent gradually to avoid kinking.

• Use the fewest 90 ° turns possible.

Determine vent length and elbows needed for best drying performance

• Use the following Vent system chart to determine type of vent material and hood

combinations acceptable to use.

NOTE: I])o not use vent runs longer than those specified in the Vent system chart.

Exhaust systems longer than those specified will:

• Shorten the life of the dryer.

• Reduce performance, resulting in longer drying times and increased energy usage.

The Vent system chart provides venting requirements that will help to achieve the best drying

performance.

Vent system chart

NOTE: Performance of rear exhaust to either side of the dryer is equivalent to adding one

elbow. To determine maximum exhaust length, add one elbow to the chart.

NOTE: Bottom exhaust performance is equivalent to adding two elbows. To determine

maximum exhaust length, add one elbow to the chart.

Number of Type of Box or Angled

90 ° turns vent Louvered hoods

or elbows hoods

O Rigid metal 100 ft (30.5 rn) 94 ft (28.7 rn)

Flexible metal 72 ft (21.9 m) 64 ft (19.5 m)

1 Rigid metal 90 ft (27.4 m) 84 ft (25.6 m)

Flexible metal 67 ft (20.4 m) 59 ft (18 m)

2 Rigid metal 80 ft (24.4 m) 74 ft (22.6 m)

Flexible metal 63 ft (19.2 m) 55 ft (16.8 m)

3 Rigid metal 71 ft (21.6 m) 65 ft (19.8 m)

Flexible metal 61 ft (18.6 m) 53 ft (16.2 m)

4 Rigid metal 63 ft (19.2 m) 57 ft (17.4 m)

Flexible metal 59 ft (18 m) 51 ft (15.5 m)

Install exhaust hood. Use caulking compound to seal exterior wall opening around

exhaust hood.

Connect vent to exhaust hood. Vent must fit inside exhaust hood. Secure vent to exhaust

hood with 4" (10.2 cm) clamp.

Run vent to dryer location. Use the straightest path possible. See "Determine vent path" in

"Plan Vent System." Avoid 90 ° turns. Use clamps to seal all joints. I])o not use duct tape,

screws or other fastening devices that extend into the interior of the vent to secure vent.

Excessive Weight Hazard

Use two or more people to move and install dryer.

Failure to do so can result in back or other injury.

To protect the floor, use a large, flat piece of cardboard from the dryer carton. Place

cardboard under the entire back edge of the dryer.

Firmly grasp the body of the dryer (not the top or console panel). Gently lay the dryer on

the cardboard. See illustration.

Examine the leveling legs. Find the diamond marking.

4. Screw the legs into the leg holes by hand. Use a wrench to finish turning the legs until the

diamond marking is no longer visible.

5. Place a carton corner post from dryer packaging under each of the 2 dryer back corners.

Stand the dryer up. Slide the dryer on the corner posts until it is close to its final location.

I.eave enough room to connect the exhaust vent.

1. Using a 4" (1 0.2 cm) clamp, connect vent to exhaust outlet in dryer. If connecting to

existing vent, make sure the vent is clean. The dryer vent must fit over the dryer exhaust

outlet and inside the exhaust hood. Check that the vent is secured to exhaust hood with a

4" (10.2 cm) clamp.

2. Move dryer into its final location. Do not crush or kink vent.

3. (On gas models) Check that there are no kinks in the flexible gas line.

4. Once the exhaust vent connection is made, remove the corner posts and cardboard.

Checkthelevelnessofthedryerbyfirstplacingalevelonthetopofthedryernearthe

console.

Then,byplacingalevelinthecreaseonthesideofthedryerbetweenthetopofthedryerand

thedryercabinet,checkthelevelnessfromfronttoback.

3. I.oosenthetopscrewfromeachofthe2hingesinStep2.

If the dryer is not level, prop up the dryer using a wood block. Use a wrench to adjust the legs

up or down and check again for levelness.

You can change your door swing from a right-side opening to a left-side opening, if desired.

1. Place a towel or soft cloth on top of the dryer or work space to protect the surface.

Remove the door assembly

1. Open the dryer door.

2. Remove the bottom screw from each of the 2 hinges that attach the dryer door to the front

panel of the dryer.

A. Loosen these screws.

t:3.Remove these screws.

4. Remove the dryer door and the hinges by lifting upward on the door. I.ay the door on a

flat, protected surface, with the inside of the door facing up. Remove remaining 2 loose

screws from dryer front panel.

5. Remove the 4 plastic plugs located outside the dryer door opening.

location of plastic

plugs shown

Install 4 plastic plugs into screw holes in the dryer left where the hinges were removed in

Step 4.

Reverse the strike

1. Remove the door strike from the dryer door opening.

2. Remove the cosmetic cover opposite the door strike.

A[ / \

3. Remove the 4 screws from the opposite side of the door.

A. Door strike

B. Cosmetic cover

3. Reinstall the door strike and cosmetic cover on the opposite side of the dryer door

opening from where they were removed.

NOTE: Door strike and plugs must be on the same side of the dryer door opening.

Reinstall the door

1. Remove the 4 screws and 2 hinges from the dryer door.

2. Replace the 4 screws in the same holes.

Screw oR,hinge

locations

--}D,_

Install the 2 hinges to the front panel of the dryer using 4 screws. Use the non-slotted side

to attach the hinge to the front panel.

Install screws in the top hinge holes in the door. Do not tighten screws, leave

approximately '/4" (5 mm) of screw exposed.

A. Instafl these screws first.

Hang door by placing screw heads into top slotted holes of hinges and slide door down.

Align bottom screw holes in hinge and door. Install two bottom screws. Tighten all hinge

screws.

7. Close door to engage door strike.

1. Check that all parts are now installed. If there is an extra part, go back through the steps to

see which step was skipped.

2. Check that you have all of your tools.

3. Dispose of/recycle all packaging materials.

4. Check the dryer's final location. Be sure the vent is not crushed or kinked.

5. Check that the dryer is [eve[. See "1 eve[ Dryer."

6. In the U.S.A.

• For power supply cord installation, plug into a grounded outlet. For direct wire

installation, turn on power.

In Canada

• Plug into a grounded 4 prong outlet. Turn on power.

7. Remove any protective film or tape remaining on the dryer.

NOTE: Glass door models have a protective film on the window that should be removed.

8. Read "Dryer Use."

9. Wipe the dryer drum interior thoroughly with a damp cloth to remove any dust.

10. If you live in a hard water area, use of a water softener is recommended to control the

buildup of scale through the water system in the dryer. Over time, the buildup of lime

scale may clog different parts of the water system, which will reduce product

performance. Excessive scale buildup may lead to the need for certain part replacement

or repair.

11. Test dryer operation by selecting a Timed Dry heated cycle and starting the dryer. For this

test, do not select the Air Fluff modifier.

If the dryer will not start, check the following:

• Controls are set in a running or "On" position.

• Start button has been pushed firmly.

• Dryer is plugged into an outlet and/or electrical supply is on.

• Household fuse is intact and tight, or circuit breaker has not tripped.

• Dryer door is closed.

This dryer automatically runs an installation diagnostic routine at the start of its first cycle.

If you receive an "L2" code, there may be a problem with your home power supply keeping

the dryer's heater from turning on. See "Troubleshooting."

If you receive an "AF" code, your dryer vent may be crushed or blocked.

See "Troubleshooting."

NOTE: You may notice an odor when the dryer is first heated. This odor is common when the

heating element is first used. The odor will go away.

La page charge ...

Maytag BRAVOS MEDB200VQ0 Manuel utilisateur

Marque: Maytag

Modèle: BRAVOS MEDB200VQ0

Catégorie: Sèche-linge électriques

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Maytag BRAVOS MEDB200VQ0 User manual

Maytag BRAVOS MEDB200VQ0 Manuel utilisateur

Maytag BRAVOS MEDB200VQ0 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents