Simpson PS60918-50 Manuel utilisateur

PROFESSIONAL PRESSURE WASHER

INSTRUCTION

MANUAL

MANUEL

D’UTILISATION

MANUAL DE

INSTRUCCIONES

SAVE THIS MANUAL FOR FUTURE REFERENCE

LISEZ ET CONSERVEZ CES INSTRUCTIONS

CONSERVE ESTAS INSTRUCCIONES PARA FUTURAS CONSULTAS

MAX.

RPM

MIN.

Part No. 7110421 Rev. 0 DEC017

If your pressure washer is not working properly or if there are parts missing or broken,

please DO NOT RETURN IT TO THE PLACE OF PURCHASE. Contact our Customer Service

Department at 1-877-362-4271 or www.simpsoncleaning.com

Si votre rondelle de pression ne travaille pas convenablement ou s'il y

a des parties manquant ou cassé, s'il vous plaît le PAS LE RETOURNE AU LIEU

D'ACHAT. Contacter notre département de service clients à 1-877-362-4271 o

www.simpsoncleaning.com

Si su lavadora a presión no trabaja correctamente ó encuentra partes rotas

ófaltantes, por favor NO LA REGRECE AL LUGAR DONDE LA COMPRO.

Contáctese con nuestro Departamento de Servicio al Cliente llamando al

1-877-362-4271 ou www.simpsoncleaning.com

IMPORTANT: Please make certain that the person who is to use this equipment carefully reads

and understands these instructions before operating.

IMPORTANT: Assurez-vous que toute personne qui utilisera cet équipement lise attentivement

ces instructions avant de l’utiliser.

IMPORTANTE: Aségurese por favor de que la persona que vaya a utilizar este equipo lea con

cuidado y comprenda estas instrucciones antes de operar.

VEA EL ESPAÑOL EN LA CONTRAPORTADA. INSTRUCTIVO DE OPERACIÓN,

CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA. ADVERTENCIA:

LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

NOTE: Photographs and line drawings used in this manual are for reference only and do

not represent a specificmodel.

REMARQUE: Les photographies et schémas figurant dans ce guide sont incorporés

seulement à titre de référence et ne représentent pas un modelparticulier.

NOTA: Las fotografías y los dibujos lineales utilizados en este manual son solo referencias

y no representan un modelo específico.

2- ENG

SAFETY GUIDELINES - DEFINITIONS

This manual contains information that is important for you to know and understand.

This information relates to protecting YOUR SAFETY and PREVENTING

EQUIPMENT PROBLEMS. To help you recognize this information, we use the

symbols below. Please read the manual and pay attention to thesesymbols.

DANGER: Indicates an imminently hazardous situation which, if not avoided,

will result in death or seriousinjury.

WARNING: Indicates a potentially hazardous situation which, if not avoided,

could result in death or seriousinjury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may

result in minor or moderateinjury.

NOTICE: Indicates a practice not related to personal injury which, if not avoided,

may result in propertydamage.

IMPORTANT SAFETY INSTRUCTIONS

DANGER: Carbon Monoxide. Using an engine indoors can kill you in

minutes. Engine exhaust contains high levels of carbon monoxide (CO), a

poisonous gas you cannot see or smell. You may be breathing CO even if you

do not smell engine exhaust.

• NEVER use an engine inside homes, garages, crawlspaces or other partly

enclosed areas. Deadly levels of carbon monoxide can build up in these areas.

Using a fan or opening windows and doors does NOT supply enough freshair.

• ONLY use outdoors and far away from open windows, doors and vents. These

openings can pull in engineexhaust.

• Even when the engine is used correctly, CO may leak into your home. ALWAYS

use a battery-powered or battery backup CO alarm in your house. Read and

follow all directions for CO alarm before using. If you feel sick, dizzy or weak

at anytime, move to fresh air immediately. See a doctor. You could have carbon

monoxidepoisoning.

WARNING: Do not operate this unit until you read this instruction manual and

the engine instruction manual for safety, operation and maintenance instructions. If

you have any questions regarding the product, please contact our customer

service department at www.simpsoncleaning.com.

DANGER: Risk of injection or severe injury. Keep clear of nozzle. Do not

direct discharge stream at persons or live animals. This product is to be used

only by trainedoperators.

WARNING: This product and its exhaust can expose you to chemicals including

lead and lead compounds, and carbon monoxide, which are known to the State of

California to cause cancer and birth defects or other reproductive harm. For more

information go to www.P65Warnings.ca.gov.

WARNING: Always wear appropriate personal hearing and other protection

during use. Under some conditions and duration of use, noise from this product

may contribute to hearing loss.

3 - ENG

WARNING: This product may not be equipped with a spark-arresting muffler.

If the product is not equipped and will be used around flammable materials or

on land covered with materials such as agricultural crops, forest, brush, grass or

other similar items, then an approved spark arrester must be installed and is legally

required in the state of California. It is a violation of California statutes section

130050 and/or sections 4442 and 4443 of the California Public Resources Code,

unless the engine is equipped with a spark arrester, as defined in section 4442, and

maintained in effective working order. Spark arresters are also required on some

U.S. Forest Service land and may also be legally required under other statutes

andordinances.

SAVE THESE INSTRUCTIONS

DANGER: RISK OF EXPLOSION OR FIRE

WHAT CAN HAPPEN HOW TO PREVENT IT

• Spilled gasoline and it’s vapors can

become ignited from cigarette sparks,

electrical arcing, exhaust gases and

hot engine components such as

themuffler.

• Shut off engine and allow it to cool before

adding fuel to thetank.

• Use care in filling tank to avoid spilling fuel.

Move pressure washer away from fueling

area before startingengine.

• Heat will expand fuel in the tank which

could result in spillage and possible

fireexplosion.

• Keep maximum fuel level 1/2" (12.7mm)

below bottom of filler neck to allow

forexpansion.

• Operating the pressure washer in an

explosive environment could result in

afire.

• Operate and fuel equipment in well-

ventilated areas free from obstructions.

Equip areas with fire extinguisher suitable

for gasolinefires.

• Materials placed against or near the

pressure washer can interfere with

its proper ventilation features causing

overheating and possible ignition of

thematerials.

• Never operate pressure washer in an area

containing dry brush orweeds.

• Muffler exhaust heat can damage

painted surfaces, melt any material

sensitive to heat (such as siding,

plastic, rubber, vinyl or the pressure

hose, itself), and damage liveplants.

• Always keep pressure washer a minimum

of 4' (1.2 m) away from surfaces (such

as houses, automobiles or live plants)

that could be damaged from muffler

exhaustheat.

• Improperly stored fuel could lead to

accidental ignition. Fuel improperly

secured could get into the hands of

children or other unqualifiedpersons.

• Store fuel in an OSHA approved container,

in a secure location away from workarea.

• Use of acids, toxic or corrosive

chemicals, poisons, insecticides, or

any kind of flammable solvent with

this product could result in serious

injury ordeath.

• Do not spray flammableliquids.

4- ENG

DANGER: RISK TO BREATHING (ASPHYXIATION)

WHAT CAN HAPPEN HOW TO PREVENT IT

• Breathing exhaust fumes will cause

serious injury or death! Engine

exhaust contains carbon monoxide,

an odorless and deadlygas.

• Operate pressure washer in a well-

ventilated area. Avoid enclosed areas

such as garages, basements,etc.

• Never operate unit in or near a location

occupied by humans oranimals.

• Some cleaning fluids contain

substances which could cause injury

to skin, eyes orlungs.

• Use only cleaning fluids specifically

recommended for high pressure washers.

Follow manufacturers recommendations.

Do not use chlorine bleach or any other

corrosive compound.

DANGER: RISK OF FLUID INJECTION AND LACERATION

WHAT CAN HAPPEN HOW TO PREVENT IT

• Your pressure washer operates at fluid

pressures and velocities high enough

to penetrate human and animal flesh

which could result in amputation or

other serious injury. Leaks caused

by loose fittings or worn or damaged

hoses can result in injection injuries.

DO NOT TREAT FLUID INJECTION

AS A SIMPLE CUT! See a physician

immediately!

• Inspect the high pressure hose regularly.

Replace the hose immediately if it is

damaged, worn, has melted from

contacting the engine, or shows any signs

of cracks, bubbles, pinholes, or other

leakage. Never grasp a high pressure

hose that is leaking ordamaged.

• Never touch, grasp or attempt to cover

a pinhole or similar water leak on the

high pressure hose. The stream of

water IS under high pressure and WILL

penetrateskin.

• Never place hands in front ofnozzle.

• Direct spray away from self andothers.

• Make sure hose and fittings are tightened

and in good condition. Never hold onto

the hose or fittings duringoperation.

• Do not allow hose to contactmuffler.

• Never attach or remove wand or hose

fittings while system ispressurized.

• When using replacement lances or guns

with this pressure washer, DO NOT use

a lance and/or lance/gun combination

that is shorter in length than what was

provided with this pressure washer as

measured from the nozzle end of the

lance to the guntrigger.

• Injuries can result if system pressure

is not reduced before attempting

maintenance ordisassembly.

• To relieve system pressure, shut off

engine, turn off water supply and pull gun

trigger until water stopsflowing.

• Use only accessories rated equal

to or higher than the rating of the

pressurewasher.

5 - ENG

DANGER: RISK OF INJURY FROM SPRAY

WHAT CAN HAPPEN HOW TO PREVENT IT

• High-velocity fluid spray can cause

objects to break, projecting particles

at highspeed.

• Always wear ANSI-approved Z87.1

safety glasses. Wear protective clothing

to protect against accidentalspraying.

• Never point wand at or spray people

oranimals.

• Light or unsecured objects can

become hazardousprojectiles.

• Always secure trigger lock when

wand is not in service to prevent

accidentaloperation.

• Never permanently secure trigger in pull-

back (open)position.

DANGER: RISK OF UNSAFE OPERATION

WHAT CAN HAPPEN HOW TO PREVENT IT

• Unsafe operation of your pressure

washer could lead to serious injury or

death to you orothers.

• Do not use chlorine bleach or any other

corrosivecompound.

• Become familiar with the operation and

controls of the pressurewasher.

• Keep operating area clear of all persons,

pets andobstacles.

• Do not operate the product when fatigued

or under the influence of alcohol or drugs.

Stay alert at alltimes.

• Never compromise the safety features of

thisproduct.

• Do not operate machine with missing,

broken or unauthorizedparts.

• Never leave wand unattended while unit

isrunning.

• If proper starting procedure is not

followed, engine can kickback causing

serious hand and arminjury.

• If engine does not start after two pulls,

squeeze trigger of gun to relieve pump

pressure. Pull starter cord slowly until

resistance is felt. Then pull cord rapidly

to avoid kickback and prevent hand or

arminjury.

• The spray gun/wand is a powerful

cleaning tool that could look like a toy

to achild.

• Keep children away from the pressure

washer at alltimes.

• Reactive force of spray will cause

gun/wand to kickback, and could

cause the operator to slip or fall or

misdirect the spray. Improper control

of gun/wand can result in injuries to

self and others.

• Do not overreach or stand on an unstable

support.

• Do not use pressure washer while

standing on a ladder.

• Grip gun/wand firmly with both

hands. Expect the gun to kickback

whentriggered.

6- ENG

DANGER: RISK OF INJURY OR PROPERTY DAMAGE WHEN

TRANSPORTING OR STORING

WHAT CAN HAPPEN HOW TO PREVENT IT

• Fuel or oil can leak or spill and could

result in fire or breathing hazard.

Serious injury or death can result.

Fuel or oil leaks will damage carpet,

paint or other surfaces in vehicles

ortrailers.

• Oil could fill the cylinder and damage

the engine if the unit is not stored or

transported in an upright position.

• If pressure washer is equipped with

a fuel shut-off valve, turn the valve to

the OFF position before transporting to

avoid fuel leaks. If pressure washer is not

equipped with a fuel shut-off valve, drain

the fuel from tank before transporting.

Only transport fuel in an OSHA-approved

container.

• Always place pressure washer on

a protective mat when transporting

to protect against damage to vehicle

fromleaks.

• Always transport and store unit in an

upright position. Remove pressure

washer from vehicle immediately upon

arrival at yourdestination.

DANGER: RISK OF ELECTRICAL SHOCK

WHAT CAN HAPPEN HOW TO PREVENT IT

• Spray directed at electrical outlets or

switches, or objects connected to an

electrical circuit, could result in a fatal

electricalshock.

• Unplug any electrically operated product

before attempting to clean it. Direct spray

away from electric outlets andswitches.

DANGER: RISK OF CHEMICAL BURN

WHAT CAN HAPPEN HOW TO PREVENT IT

• Use of acids, toxic or corrosive

chemicals, poisons, insecticides, or

any kind of flammable solvent with this

product could result in serious injury

ordeath.

• Do not spray acids, gasoline, kerosene,

or any other flammable materials with this

product. Use only household detergents,

cleaners and degreasers recommended

for use with pressurewashers.

• Wear protective clothing to protect

eyes and skin from contact with

sprayedmaterials.

7 - ENG

WARNING: RISK OF BURSTING

WHAT CAN HAPPEN HOW TO PREVENT IT

• Over inflation of tires could result in

serious injury and property damage.

• Use a tire pressure gauge to check the

tires pressure before each use and while

inflating tires; see the tire sidewall for the

correct tire pressure.

NOTE:

Air tanks, compressors and similar

equipment used to inflate tires can fill small

tires similar to these very rapidly. Adjust

pressure regulator on air supply to no more

than the rating of the tire pressure. Add air

in small increments and frequently use the

tire gauge to prevent overinflation.

• High-velocity fluid spray directed at

pneumatic tire sidewalls (such as

found on automobiles, trailers and

the like) could damage the sidewall

resulting in serious injury.

• On pressure washers rated above

1600 PSI (11032 kPa) use the widest

fan spray (40º nozzle) and keep the

spray a minimum of 8" (20 cm) from the

pneumatic tire sidewall. Do not aim spray

directly at the joint between the tire and

rim.

WARNING: RISK OF HOT SURFACES

WHAT CAN HAPPEN HOW TO PREVENT IT

• Contact with hot surfaces, such as

engine exhaust components, could

result in seriousburn.

• During operation, touch only the control

surfaces of the pressure washer. Keep

children away from the pressure washer

at all times. They may not be able to

recognize the hazards of thisproduct.

WARNING: RISK OF INJURY FROM LIFTING

WHAT CAN HAPPEN HOW TO PREVENT IT

• Serious injury can result from

attempting to lift too heavy anobject.

• The pressure washer is too heavy to be

lifted by one person. Obtain assistance

from others beforelifting.

SAVE THESE INSTRUCTIONS

FOR FUTURE USE

8- ENG

QUICK SETUP GUIDE

WARNING: To reduce the risk of injury, read the pressure washer instruction

manual and the engine instruction manual before operating pressure washer.

IMPORTANT: Ethanol Shield

TM

(sold separately) is a fuel stabilizer that helps

eliminate and prevent ethanol related problems in power equipment. Follow the

instructions on the container and add to the gasoline.

A

Install the

Handle

Slide the handle

assembly onto the

frame. (if equipped) Align

holes in the top handle

with the mounting holes

in the handle assembly.

Secure with saddle

bolts and knobs.

OR

B

Add/Check Oil

The engine

is shipped

without oil. Before

starting engine, add

the oil provided. Check

oil level prior to each

use. Refer to Engine

Owner’s Manual for

complete procedure.

C

Add Gasoline

In a well

ventilated

outdoor area add fresh,

high quality, unleaded

gasoline with a pump

octane rating of 86 or

higher. Do not overfill.

Wipe up spilled fuel

before starting the

engine. Refer to Engine

Owner's Manual for

complete procedure.

QUICK START GUIDE

DANGER:

• Never run engine indoors or in enclosed, poorly ventilated areas. Engine

exhaust contains carbon monoxide, an odorless and deadly gas.

• Risk of fluid injection and laceration. When using the high-pressure setting,

DO NOT allow the high-pressure spray to come in contact with unprotected

skin, eyes or with any pets or animals. Serious injury will occur.

9 - ENG

1

Connect Garden

Hose to Pump

Thread the

garden hose to

the pump inlet.

2

Connect High

Pressure Hose

to Pump

Connect the high

pressure hose to

the pump outlet.

OR

3

Connect High

Pressure Hose

to Spray Gun

Thread the other end

of the high pressure

hose to the spray gun.

OR

4

Connect Spray

Wand to Spray

Gun

Thread the spray

wand into the end

of the spray gun.

5

Connect QC

Nozzles to Spray

Wand

Pull quick connect

coupler back and insert

nozzle. Release quick

connect coupler and

twist nozzle to make sure

it is secure in coupler.

6

Turn Water

Faucet

Completely On

Do not run the unit

without water supply

connected and turned on.

Use Cold Water Only.

7

Release Air from

System

Release all

air from pump and

high pressure hose by

depressing trigger until a

steady stream of water is

present. Approximately

30 seconds.

30 S

8

Start engine. See

Engine Owner's

Manual for

correct

procedure.

WARNING: This Guide is not a substitute for reading the operator's manual.

User must read and understand operator's manual before using this product.

10- ENG

GET TO KNOW THE PRESSURE WASHER

NOTE: Photographs and line drawings used in this manual are for reference

only and do not represent a specificmodel.

Compare the illustrations with your unit to familiarize yourself with the location of

various controls and adjustments. Save this manual for future reference.

MAX.

RPM

MIN.

G

C

B

1

D

K L

H

I

J

A

E

BASIC ELEMENTS OF A PRESSURE WASHER (FIG. 1)

A. High Pressure Pump: Increases the pressure of the watersupply.

B. Engine: Drives the high pressure pump. Refer to the Engine Owner's Manual

for location and operation of enginecontrols.

C. High Pressure Hose: Carries the pressurized water from the pump to the gun

and spray wand.

D. Spray Gun: Connects with spray wand to control water flow rate, direction

andpressure.

E. Quick-Connect Spray Wand: Allows the user to quickly change out

high pressure nozzles. See How To Use Spray Wand instructions in

Operationsection.

F. Detergent Siphon Hose (not shown): Feeds cleaning agents into the pump to mix

with the water. See

How To Apply Chemicals/Cleaning Solvents

instructions

in

Operation

section.

G. Handle

H. Frame

I. Pump Outlet

11 - ENG

J. Pump Inlet

K. Quick Connect Nozzles

L. Nozzle Holder

BASIC ELEMENTS OF AN ENGINE

Refer to the Engine Owner's Manual for location and operation of enginecontrols.

Choke Control: Opens and closes carburetor chokevalve.

Starter Grip: Pulling starter grip operates recoil starter to crankengine.

Engine Switch: Enables and disables ignitionsystem.

ASSEMBLY INSTRUCTIONS (FIG. 2–4)

1. Locate and remove all loose parts from thecarton.

2. Cut four corners of the carton from top to bottom and lay the panelsflat.

3.

(Figure 2) Slide the handle assembly (G) onto the frame (H)and secure with

saddle bolts andknobs.

OR

3. (Figure 2A) Align holes in the top handle (S) with the mounting holes in the

handle assembly (G). Insert saddle bolts (DD) through aligned holes and

secure top handle to handle assembly with knobs (EE). Tighten until snug.

NOTICE: Risk of personal injury. Avoid placing hands between handle and frame

when assembling to preventpinching.

G

H

2

EE

G

H

2A

G

S

DD

4. Remove the colored quick-connect nozzles (K) from the plastic bag and insert

them into correct grommet on the nozzle holder (L). Nozzles are color coded

to match colored nozzles on label.

K

L

2B

5. Connect wand (E) to gun (D). Tightensecurely.

12- ENG

6. Attach high pressure hose (C) to gun (D). Tightensecurely.

OR

E

4

D

C

3

D

C

NOTICE: The engine is shipped without oil. Before starting engine, add the oil

provided. Damage to the engine will occur if the engine is run without oil, this

damage will not be covered underwarranty.

NOTICE: The high-pressure pump was filled with oil at the factory. Always check oil

level before using (refer to Maintenance for more information).

OPERATION

PRESSURE WASHER TERMINOLOGY

PSI: Pounds per Square Inch. The unit of measure for water pressure. Also used

for air pressure, hydraulic pressure, etc.

PSI*: Pounds per Square Inch. The unit of measure for water pressure. Also used

for air pressure, hydraulic pressure, etc.

GPM*: Gallons per Minute. The unit of measure for the flow rate of water.

* Rated Pressure and Rated Water Flow is within manufacturing tolerance of

(+/- 10%).

Bypass Mode: Allows water to re-circulate within the pump when the gun trigger is

not pulled. This feature allows the operator to release the trigger gun and reposition

themselves without having to turn the engine off in between cleaningactions.

WARNING: Do not allow the unit to run for more than two minutes without

the gun trigger being pulled. This could cause overheating and damage to

the pump. When the temperature inside the pump rises too high, the thermal

relief valve will open and release a spray of water from the pump to lower the

internal temperature. The valve will thenclose.

Thermal Relief Valve (P, Fig. 5): When the temperature inside the

5

P

pump rises too high, this valve will open and release a gush of

water in an effort to lower the temperature inside the pump. The

valve will thenclose. NOTE: Thermal relief valve location will vary

depending on the pump type.

Detergent Injection System: Mixes cleaners or cleaning solvents

with the water to improve cleaning effectiveness.

Water Supply: All pressure washers must have a source of water. The minimum

requirements for a water supply are 20 PSI and 5 Gallons Per Minute. If your water

source is a well, the garden hose length can only be 30ft. (9m) max.

WARNING: To reduce the possibility of contamination always protect

against backflow when connected to a potable watersystem.

13 - ENG

PRESSURE WASHER OPERATING FEATURES

PRESSURE ADJUSTMENTS (FIG. 6)

The pressure setting is preset at the factory to achieve optimum pressure and

cleaning. If you need to lower the pressure, it can be accomplished by these

methods.

1. Back away from the surface to be cleaned. The further away you are, the

less the pressure will be on the surface to becleaned.

2. Change to the 40˚ nozzle (white). This nozzle delivers a less powerful stream

of water and a wider spray pattern. Refer to How To Use SprayWand.

3. (if equipped) This pressure washer’s high

-

+

6

pressure pump is equipped with an additional

feature that allows the pressure setting to be

adjusted.

To lower the pressure, turn the pressure con-

trol knob on the pump counterclockwise to

the desired pressure.

To return the pump pressure to the factory setting, turn the pressure control

knob on the pump clockwise until itstops.

NOTICE: DO NOT overtighten the pressure control knob, if overtightened the knob

COULD break and result in immediate loss of water pressure and costly repairs to

theunit.

DIAL-N-WASH ADJUSTMENT (FIG. 7, 8) (IF EQUIPPED)

1. Choose the correct high pressure nozzle (0˚, 15˚ or 40˚) for the job to be

performed. Refer to How To Use SprayWand.

2. The Dial-N-Wash is shipped in the MAX pressure setting, the MAX pressure

bar is aligned with the arrow (R) on the collar as shown in Figure 7.

Rotating the Dial-N-Wash (Q) counterclockwise until it stops places it in the

MIN pressure setting, the arrow (R) will align with the MIN pressure bar as

shown in Figure 8.

8

R

Q

7

R

Adjust the pressure by rotating the

Dial-N-Wash (Q) clockwise for

higher pressure or

counterclockwise for lower

pressure, aligning the arrow with

the desired pressure bar on the

Dial-N-Wash.

NOTE: To apply chemicals the black low pressure nozzle must be installed and

the Dial-N-Wash must be in the MAX pressuresetting.

14- ENG

HOW TO USE SPRAY WAND

The nozzles for the spray wand are stored in the nozzle holder on the panel assembly.

Colors on the panel identify nozzle location and spray pattern. Refer to the following

chart to choose the correct nozzle for the job to beperformed.

CHANGING NOZZLES ON SPRAY WAND (FIG. 9)

DANGER: Risk of fluid injection. Do not direct discharge stream toward

persons, unprotected skin, eyes or any pets or animals. Serious injury

willoccur.

WARNING: Flying objects could cause risk of serious injury. Do not

attempt to change nozzles while pressure washer is running. Turn engine off

before changingnozzles.

1. Pull quick-connect coupler (E) back and insert nozzle (K).

K

E

9

2. Release quick-connect coupler and twist nozzle to

make sure it is secure incoupler.

WARNING: Flying object could cause risk of serious

injury. Ensure nozzle is completely inserted in quick-

connect socket and quick-connect collar is fully engaged

(forward) before squeezing guntrigger.

NOZZLE COLOR SPRAY PATTERN USES SURFACES**

Red

0˚

powerful

pinpoint for

spot cleaning of

hard, unpainted

surfaces or for

high reach areas

unpainted metal

or concrete;

DO NOT use on wood

Yellow

15˚

intense cleaning

of unpainted

hard surfaces

grills, driveways, concrete

or brick walkways,

unpainted brick or stucco

Green

25˚

standard cleaning

nozzle for most

applications

yard tools, sidewalks, lawn

furniture, unpainted siding,

stucco, gutters and eaves,

concrete, brick surfaces

White

40˚

cleaning of

painted or

delicate surfaces

auto/RV, marine, wood,

painted brick and stucco,

vinyl, painted siding

Black

low pressure

applies cleaning

solutions

Low pressure spray is

safe on all surfaces.

Always verify compatibility

of cleaning solution

prior touse.

15 - ENG

**NOTICE: The high pressure spray from your pressure washer is capable of

causing damage to surfaces such as wood, glass, automobile paint, auto striping

and trim, and delicate objects such as flowers and shrubs. Before spraying, check

the item to be cleaned to assure yourself that it is strong enough to resist damage

from the force of the spray.

HOW TO APPLY CHEMICALS/CLEANING SOLVENTS (FIG. 10)

Applying chemicals or cleaning solvents is a low pressure operation. NOTE: Use

only soaps and chemicals designed for pressure washer use. Do not usebleach.

To Apply Chemicals:

1. Ensure detergent siphon hose (F, Figure 10) is attached

F

10

to barbed fitting location near high pressure hose

connection of pump as shown. NOTE: The barbed

fitting location will vary depending on the pump type.

2. Place other end of detergent siphon hose with

filter on it into container holding chemical/cleaning

solution. NOTE: For every 7 gallons of water pumped

1 gallon of chemical/cleaning solution will beused.

3. Install low pressure (black) nozzle into quick connect fitting of spray wand, see

How To Use Spray Wand paragraph in thissection.

4. After use of chemicals, place detergent siphon hose into container of clean

water and draw clean water through chemical injection system to rinse system

thoroughly. If chemicals remain in the pump, it could be damaged. Pumps

damaged due to chemical residue will not be covered underwarranty.

NOTE: Chemicals and soaps will not siphon if the black soap nozzle is not installed

on the spraywand.

STARTING (FIG. 11–14)

WARNING: To reduce the risk of injury, read the pressure washer instruction

manual and the engine instruction manual before starting pressurewasher.

DANGER: Risk of fluid injection and laceration. When using the high

pressure setting, DO NOT allow the high pressure spray to come in contact

with unprotected skin, eyes, or with any pets or animals. Serious injury

willoccur.

• Your washer operates at fluid pressures and velocities high enough to penetrate

human and animal flesh, which could result in amputation or other serious injury.

Leaks caused by loose fittings or worn or damaged hoses can result in injection

injuries. DO NOT TREAT FLUID INJECTION AS A SIMPLE CUT! See a physician

immediately!

DANGER: Carbon Monoxide. Using an engine indoors can kill you in

minutes. Engine exhaust contains high levels of carbon monoxide (CO), a

poisonous gas you cannot see or smell. You may be breathing CO even if you

do not smell engine exhaust.

• Breathing exhaust fumes will cause serious injury or death! Engine exhaust

contains carbon monoxide, an odorless and deadlygas.

• Operate pressure washer in a well-ventilated area. Avoid enclosed areas

such as garages, basements,etc.

• Never operate unit in or near a location occupied by humans oranimals.

16- ENG

WARNING: Risk of Fire, Asphyxiation and Burn. Never fill fuel tank when

engine is running or hot. Do not smoke when filling fueltank.

• Never fill fuel tank completely. Fill tank to 1/2" (12.7 mm) below bottom of filler

neck to provide space for fuel expansion. Wipe any fuel spillage from engine and

equipment before startingengine.

• DO NOT let hoses come in contact with very hot engine muffler during or

immediately after use of your pressure washer. Damage to hoses from contact with

hot engine surfaces will NOT be covered bywarranty.

NOTICE: Risk of property damage. Never pull water supply hose to move pressure

washer. This could damage hose and/or pumpinlet.

• DO NOT use hot water, use cold wateronly.

• Never turn water supply off while pressure washer engine is running or damage to

pump willresult.

• DO NOT stop spraying water for more than two minutes at a time. Pump operates in

bypass mode when spray gun trigger is not pressed. If pump is left in bypass mode

for more than two minutes internal components of the pump can bedamaged.

If you do not understand these precautions, please contact our customer service

department at www.simpsoncleaning.com

Prior to starting, refer to your engine manual for proper startingprocedure.

1. In a well ventilated outdoor area add fresh, high quality, unleaded gasoline with

a pump octane rating of 86 or higher. Do not overfill. Wipe up spilled fuel before

starting the engine. Refer to Engine Owner's Manual for correctprocedure.

IMPORTANT: Ethanol Shield

TM

(sold separately) is a fuel stabilizer that helps

eliminate and prevent ethanol related problems in power equipment. Follow the

instructions on the container and add to thegasoline.

NOTICE: Use of fuels with greater than 10% ethanol are

not approved for use in this product per EPA regulations

and will damage the unit and void thewarranty.

2. Check engine oil level. Refer to Engine Owner's Manual for correct procedure.

3. Check pump oil level. The oil level should come to the dot in the middle of the

sight glass. Refer to the Pump paragraph underMaintenance.

4. Connect the water hose to the water source. Turn the water source on to

remove all air from the hose. When a steady stream of water is present, turn

the water source off.

5. Verify the filter screen (M) is in water inlet of pump. NOTE: Convex side

facesout.

6. Connect water source (N) to pump inlet (J). NOTE: Water source must provide

a minimum of 5 gallons per minute at 20 PSI.

7. Connect

high pressure hose (C) to pump outlet (I).

I

13

C

12

N

J

M

11

I

C

OR

WARNING: To reduce the possibility of contamination always protect

against backflow when connected to a potable watersystem.

17 - ENG

8. Choose the correct nozzle for the job to be performed. See How To Use spray

Wand instructions in this section. NOTE: If applying a chemical or cleaning

solution, see How To Apply Chemicals/Cleaning Solvents instructions in

thissection.

9. Turn water source on.

NOTICE: Risk of property damage. Failure to do so could cause damage to

thepump.

10. Remove all air from the pump and high pressure hose by depressing trigger

until a steady stream of water is present.

11. Start engine. See Engine Owner's Manual for correct procedure.

WARNING: Risk of unsafe operation. If engine does not start after two

pulls, squeeze trigger of gun to relieve pump pressure. Pull starter cord slowly

until resistance is felt. Then pull cord rapidly to avoid kickback and prevent

hand or arminjury.

NOTE: If the oil level in the engine is low, the engine will not start. If the engine does

not start, check the oil level and add oil asneeded.

12. Depress trigger on gun to start water flow.

WARNING: Do not allow the unit to run for more than two minutes without

the gun trigger being pulled. This could cause overheating and damage to

the pump. When the temperature inside the pump rises too high, the thermal

relief valve will open and release a spray of water from the pump to lower the

internal temperature. The valve will thenclose.

WARNING: Risk of unsafe operation. Stand on a stable surface and

grip gun/spray wand firmly with both hands. Expect the gun to kick

whentriggered.

13. Release trigger to stop waterflow.

WARNING: Risk of injury from spray. Always engage

14

O

the trigger lock (O) when gun is not in use. Failure to do so

could cause accidentalspraying.

SHUTTING DOWN

1. After each use, if you have applied chemicals, place

detergent siphon hose into container of clean water and

draw clean water through chemical injection system to

rinse system thoroughly.

NOTICE: Risk of property damage. Failure to do so could cause damage to the

pump.

2. Turn engine off. See Engine Owner's Manual.

NOTICE: Risk of property damage. NEVER turn the water off with the enginerunning.

3. Turn water sourceoff.

4. Pull trigger on spray gun to relieve any water pressure in hose or spraygun.

NOTE: Failure to release system pressure will prevent removal of high pressure

hose from spray gun or pumpconnection.

5. See Storage section in this manual for proper storageprocedures.

18- ENG

MAINTENANCE

WARNING: Risk of burn hazard. When performing maintenance, you may

be exposed to hot surfaces, water pressure or moving parts that can cause

serious injury ordeath.

WARNING: Risk of fire hazard. Always disconnect, spark plug wire,

let the engine cool and release all water pressure before performing any

maintenance or repair. The engine contains flammable fuel. Do not smoke or

work near open flames while performingmaintenance.

To ensure efficient operation and longer life of your pressure washer, a routine

maintenance schedule should be prepared and followed. If the pressure washer is

used in unusual conditions, such as high-temperatures or dusty conditions, more

frequent maintenance checks will berequired.

ENGINE

Consult the Engine Owner's Manual for the manufacturer's recommendations

for any and all maintenance. NOTE: The engine drain plug is located at the rear of

theunit.

PUMP (FIG. 15)

NOTE: The Pump was filled with oil at the factory. The preferred oil is SIMPSON

®

Premium Pump Crankcase Oil. If this oil is not available, an SAE 15W-40 oil may

be used. Change the pump oil after the first 50hours of operation and every 100

hours thereafter, or every 3months.

TO CHECK OIL

The oil level should come to the dot in the middle of

15

CC

AA

BB

the sight glass (AA).

HOW TO CHANGE PUMP OIL

1. Loosen pump oil fill plug (BB).

2. Place a container under the pump oil drain plug

(CC).

3. Remove pump oil drainplug.

4. After oil is drained, replace pump oil drain plug.

Tightensecurely.

5. For AAA

TM

pumps, refill using SIMPSON

®

Premium Pump Crankcase Oil. If this

oil is not available, an SAE 15W-40 oil may be used.

For CAT Pumps

®

***, refill using a non-detergent hydraulic oil (ISO 68).

6. Replace pump oil fill plug and tightensecurely.

If there is a problem with the pump contact us at www.simpsoncleaning.com

*** CAT PUMPS

®

is a registered trademark of Diversified Dynamics Corporation.

CONNECTIONS

Connections on pressure washer hoses, gun and spray wand should be cleaned

regularly and lubricated with light oil or lithium grease to prevent leakage and

damage to the o-rings.

NOZZLE CLEANING (FIG. 16)

If the nozzle becomes clogged with foreign materials, such as dirt, excessive

pressure may develop. If the nozzle becomes partially clogged or restricted, the

pump pressure will pulsate. Clean the nozzle immediately using the nozzle kit

supplied and the following instructions:

19 - ENG

1. Shut off the pressure washer and turn off the watersupply.

2. Pull trigger on gun handle to relieve any waterpressure.

3. Disconnect the spray wand from thegun.

4. Remove the high pressure nozzle (K) from the spray wand.

16

K

N

Remove any obstructions with the nozzle cleaning tool

provided and backflush with cleanwater.

5. Direct water supply (N) into nozzle to backflush loosened

particles for 30seconds.

6. Reassemble the nozzle to the wand.

7. Reconnect spray wand to gun and turn on watersupply.

8. Start pressure washer and place spray wand into high pressure setting totest.

CLEAN THE WATER INLET FILTER (FIG. 11)

This screen filter should be checked periodically and cleaned if necessary.

1. Remove filter by grasping end and removing it from water inlet of pump.

2. Clean filter by flushing it with water on bothsides.

3. Re-insert filter into water inlet of pump. NOTE: Convex side facesout.

NOTE: Do not operate the pressure washer without filter properly installed.

STORAGE

ENGINE

Consult the Engine Owner's Manual for manufacturer’s recommendations

forstorage.

TO PREVENT FUEL-RELATED PROBLEMS

1. Add Ethanol Shield

TM

fuel stabilizer following the manufacturer’s instructions.

When adding a gasoline stabilizer, fill the fuel tank with fresh gasoline. If only

partially filled, air in the tank will promote fuel deterioration during storage. If

you keep a container of gasoline for refueling, be sure that it contains only

freshgasoline.

2. After adding a gasoline stabilizer, run the engine outdoors for 10 minutes

to be sure that treated gasoline has replaced the untreated gasoline in

thecarburetor.

3. Turn the fuel valve to the OFFposition.

4. Continue to run the engine until it stops from the lack of fuel in the carburetor

fuel bowl. Running time should be less than 3minutes.

PUMP

The manufacturer recommends using SIMPSON

®

/ POWERWASHER

®

Pump

Guard or equivalent when storing the unit for more than 30 days and/or when

freezing temperatures are expected. SIMPSON

®

/ POWERWASHER

®

Pump Guard

is environmentallyfriendly.

NOTE: Using pump guard helps provide proper lubrication to the internal seals of

the pump regardless of temperature or environment.

NOTICE: Risk of property damage. Use only SIMPSON

®

/ POWERWASHER

®

Pump Guard or equivalent. Other products could be corrosive and/or contain alco-

hol which may cause pumpdamage.

1. Turn off pressure washer and disconnect hoses frompump.

20- ENG

2. Unscrew bottle valve from Pump Guard bottle and remove seal.

3. Screw bottle valve back ontobottle.

4. Attach bottle to water inlet ofpump.

5. Squeeze bottle to inject contents intopump.

6. With ignition switch off, simultaneously pull starter rope and squeeze bottle.

Repeat until protector fluid exits pump outlet. NOTE: This step may require

twopeople.

ACCESSORIES

DANGER: Risk of fluid injection. When using replacement spray wands

or guns with this pressure washer, DO NOT use a spray wand and/or spray

gun/wand combination that is shorter in length than what was provided with

this pressure washer as measured from the nozzle end of the wand to the

guntrigger.

NOTICE: The use of any other accessory not recommended for use with this tool

could be hazardous. Use only accessories rated equal to or greater than the rating

of the pressurewasher.

SERVICE INFORMATION

Do not return this product to your retailer. Please contact our customer service

department at www.simpsoncleaning.com

LIMITED WARRANTY

The manufacturer of this product agrees to repair or replace designated parts that

prove defective within the warranty period listed below at the manufacturer’s sole

discretion. Specific limitations/extensions and exclusions apply.

This warranty covers defects in material and workmanship and not parts failure

due to normal wear, depreciation, abuse, accidental damage, negligence, improper

use, maintenance, water quality or storage. To make a claim under the terms of the

warranty, all parts said to be defective must be retained and available for return

upon request to a designated Warranty Service Center for warranty inspection. The

judgments and decisions of the manufacturer concerning the validity of warranty

claims are final.

These warranties pass through to the end user and are non-transferable. As a

factory authorized and trained Warranty Service Center, the factory will honor the

terms of all component warranties and satisfy claims of the appropriate warranty

provisions.

Normal wear items include, but are not limited to, valves and seals, which are not

covered by this warranty.

This warranty replaces all other warranties, express or implied, including without

limitation any warranties of merchantability or fitness for a particular purpose and

all such warranties are hereby disclaimed and excluded by the manufacturer. The

manufacturer’s warranty obligation is limited to repair and replacement of defec-

tive products as provided herein and the manufacturer shall not be liable for any

further loss, damages, or expenses – including damages from shipping, accident,

abuse, acts of God, misuse, or neglect. Neither is damage from repairs using parts

not purchased from the manufacturer or alterations performed by non-factory

authorized personnel. Failure to install and operate equipment according to the

guidelines put forth in the instruction manual shall void warranty.

La page charge ...

Simpson PS60918-50 Manuel utilisateur

Ce manuel convient également à

Simpson PS60918-50 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents