XO XOBI36SMUA Manuel utilisateur

RANGE HOOD - User instructions

HOTTE DE CUISINE - Notice d’utilisation

CAMPANA EXTRACTORA - Manual de utilización

USA

F

E

XOBI36SMUA

NEED HELP?

Call our ventilation experts toll free al 800-966-8300

AVEZ-VOUS BESOIN D’AIDE ?

Contactez nos experts au numéro gratuit 800-966-8300

¿NECESITA AYUDA?

Póngase en contacto con nuestros expertos a través del número gratis 800-966-8300

Proof of original purchase date and invoice is needed to obtain

service under warranty.

Limited 2 Year Warranty.

For 2 years from the original date of purchase, we will provide,

free of charge, parts and service labor in your home to repair or

replace any part of the hood that fails because of a manufacturing

defect.

The warranty is extended to the original purchaser for products

purchased for ordinary home use in North America.

Should you require service for your XO product call a product

service specialist at 800.966.8300

Improper Installation.

Service trips to the home to teach you how to use the product.

Resetting circuit breakers.

Damage caused after delivery.

EXPECT MORE FROM XO

When buying any XO appliance

you can be confident

you have purchased a high quality,

innovative, and stylish product,

from a company who cares about you

XO Hood Warranty

What is covered

What is not covered

- 3 -

IMPORTANT SAFETY INSTRUCTIONS

FOR RESIDENTIAL USE ONLY

READ AND SAVE THESE INSTRUCTIONS

PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING.

IMPORTANT: Save these Instructions for the Local Electrical Inspectors use.

INSTALLER: Please leave these Instructions with this unit for the owner.

OWNER: Please retain these instructions for future reference.

Take care when using cleaning agents or detergents.

Suitable for use in household cooking area.

WARNING - To reduce the risk of re or electric shock, do not use this fan with any

Solid-State Speed Control Device.

CAUTION - To reduce risk of re and to properly exhaust air, be sure to duct air out-

side – Do not vent exhaust air into spaces within walls or ceilings or into attics, crawl

spaces, or garages.

CAUTION - For general ventilating use only. Do not use to exhaust hazardous or ex-

plosive materials and vapors.

CAUTION - To avoid motor bearing damage and noisy and/or unbalanced impellers,

keep drywall spray, construction dust, etc. o power unit.

CAUTION - Please read specication label on product for further information and

requirements.

WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

A. Use this unit only in the manner intended by the manufacturer. If you have questions,

contact the manufacturer.

B. Before servicing or cleaning unit, switch power o at service panel and lock the serv-

ice disconnecting means to prevent power from being switched on accidentally.

When the service disconnecting means cannot be locked, securely fasten a promi-

nent warning device, such as a tag, to the service panel.

WARNING - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

A. Never leave surface units unattended at high settings. Boilovers cause smoking and

greasy spillovers that may ignite. Heat oils slowly on low or medium settings.

B. Always turn hood ON when cooking at high heat or when ambeing foods (i.e.

ENGLISH

USA

- 4 -

Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambè).

C. Clean ventilating fans frequently. Grease should not be allowed to accumulate on

fan or lter.

D. Use proper pan size. Always use cookware appropriate for the size of the surface

element.

E. Keep fan, lters and grease laden surface clean.

F. Use high range setting on range only when necessary. Heat oil slowly on low to me-

dium setting.

G. Don’ t leave range unattended when cooking.

H. Always use cookware and utensils appropriate for the type and amount o food be-

ing prepared.

WARNING – TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE

TOP GREASE FIRE, OBSERVE THE FOLLOWING

a

:

A. SMOTHER FLAMES with a close-tting lid, cookie sheet, or metal tray, then turn o

the burner. BE CAREFUL TO PREVENT BURNS. If the ames do not go out immediately,

EVACUATE AND CALL THE FIRE DEPARTMENT.

B. NEVER PICK UP A FLAMING PAN – You may be burned.

C. DO NOT USE WATER, including wet dishcloths or towels – a violent steam explosion

will result.

D. Use an extinguisher ONLY if:

1. You know you have a Class ABC extinguisher, and you already know how to operate

it.

2. The re is small and contained in the area where it started.

3. The re department is being called.

4. You can ght the re with your back to an exit.

a

Based on “kitchen resafety tips” published by NFPA

Proper maintenance of the Range Hood will assure proper performance of the

unit.

INSTALLATION INSTRUCTIONS

WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

A. Installation work and electrical wiring must be done by qualied person(s) in accord-

ance with all applicable codes and standards, including re-rated construction.

B. Sucient air is needed for proper combustion and exhausting of gases through the

ue (chimney) of fuel burning equipment to prevent back drafting. Follow the heat-

ing equipment manufacturer’s guideline and safety standards such as those pub-

lished by the National Fire Protection Association (NFPA), and the American Society

for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local

code authorities.

C. When cutting or drilling into wall or ceiling, do not damage electrical wiring and

other hidden utilities.

- 5 -

D. Ducted fans must always be vented to the outdoors.

E. This unit must be grounded.

WARNING - TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.

WARNING - UNDER CERTAIN CIRCUMSTANCES DOMESTIC APPLIANCES MAY BE DAN-

GEROUS.

A. Do not check lters with hood working.

B. Do not touch the lamps after a prolonged use of the appliance.

C. No food must be cooked ambè underneath the hood.

D. The use of an unprotected ame is dangerous for the lters and could cause res.

E. Watch constantly the fried food in order to avoid the cooking oil ares up.

F. Before performing any mainteinance operation, disconnect the hood from the elec-

trical service.

The manufacturers will not to accept any responsability for eventual damages, be-

cause of failure to observe the above instructions.

- 6 -

Installation Preparation

DUCT FITTINGS:

This Hood Must Use an

6" Round Duct. It Can

Transition to 3-1/4" x10"

or 3-1/4" x 12" Duct.

Use this chart to compu-

te maximum permissible

lengths for duct runs to

outdoors.

NOTE: Do not exceed maxi-

mum permissible equivalent

lengths!

Maximum duct length:

100 feet for range ho-

ods.

Flexible ducting:

If flexible metal ducting

is used, all the equivalent

feet values in the table

should be doubled. The

flexible metal duct should

be straight and smooth

and extended as much as

possible.

DO NOT use flexible plastic

ducting.

NOTE: Any home ventilation

system, such as a ventilation

hood, may interrupt the

proper flow of combustion

air and exhaust required

by fireplaces, gas furnaces,

gas water heaters and other

naturally vented systems. To

minimize the chance of in-

terruption of such naturally

vented systems, follow the

heating equipment manu-

facturer’s guidelines and

safety standards such as

those published by NFPA.

Duct

Piece:

Dimensions:

Equivalent

Number

Length*:

Quantity

Used:

Total

Equivalent

Length:

Round, straight

1 ft. (per foot

lenhgth)

3-1/4" x 10"

straight

1 ft. (per foot

lenhgth)

90° elbow 12 ft.

45° elbow 7 ft.

3-1/4" x 10"

3-1/4" x 12"

90° elbow

14 ft.

10 ft.

3-1/4" x 10"

3-1/4" x 12"

45° elbow

8 ft.

6 ft.

3-1/4" x 10"

3-1/4" x 12"

90° elbow

33 ft.

24 ft.

6" round to

rectangular

2 ft.

Rectangular to

8" round

2 ft.

3-1/4" x 10"

3-1/4" x 12"

6" round to

rectangular

transition 90°

elbow

4 ft.

3-1/4" x 10"

3-1/4" x 12"

Rectangular to

6" transition

90° elbow

4 ft.

Round wall

cap with

dramper

24 ft.

3-1/4" x 10"

3-1/4" x 12"

Rectangular

wall cap with

dramper

24 ft.

18 ft.

Round roof

cap

33 ft.

*Actual length of straight duct plus duct

fitting equivalent. Equivalent length of duct

pieces reflect requirements for good venting

performance with any ventilation hood.

Total Duct Run =

- 7 -

WARNING FIRE HAZARD

NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces,

ceiling, attics or garages.

All exhaust must be ducted to the outside, unless using the recirculating option.

Use single wall rigid Metal ductwork only.

Fasten all connections with sheet metal screws and tape all joints w/ certied Silver

Tape or Duct Tape.

INSTALL THE DUCTWORK:

NOTE: To reduce the risk of re, use only metal ductwork.

1. Decide where the ductwork will run between the hood and the outside.

2. A straight, short duct run will allow the hood to perform most eciently.

3. Long duct runs, elbows, and transitions will reduce the performance of the hood.

Use as few of them as possible.

4. Install a roof or wall cap. Connect 6" round metal ductwork to cap and work back

towards hood location. Use duct tape to seal the joints between ductwork sections.

Installation - Ducting Options

- 8 -

8-1/2"

11-9/16"

10-1/4"

26-1/4"

Max 42-5/16" - Min 31-3/16"

7/8"

36"

23-5/8"

Min 27" - Max 32"

36"

Hood Specications

 Front of hood

 Side of hood

 Top of hood  Mounting height and

clearance:

PRODUCT DIMENSIONS AND CLEARANCE

XOBI36SMUA:

- 9 -

INSTALLATION INSTRUCTIONS

INSTALLATION  VENTED TO THE OUTSIDE

1. INSTALLATION:

Remove the structure from the packaging

and remove the 2 screws A to separatethe

upper part from the lower part (Fig.1).

- Position hole template on the ceiling pay-

ing attention that the arrow is positioned

on the same side as the appliance controls

(Fig.2).

Make 4, Ø8 holes in the ceiling and drive

in 3 screws without completely tightening

them. Pay attention not to insert the screw

into the hole marked with an X on the hole

template (the screws and expansion plugs

must be suitable for the type of wall).

- Take the upper part of the structure B

(Fig.3) and insert the 3 slots onto the 3

screws that are not completely tightened.

Rotate slightly to t (Fig.3).

Drive in the fourth screw X and tighten the

remaining 3 to allow denitive blocking of

the upper part ofstructure B.

- Take the lower part of the telescopic

structure C and insert it into the upper

structure B (Fig.4).

Adjust the height and block it using the 8

screws G that are supplied (Fig.5).

- Fix the exible pipe to the prepared air

evacuation hole (Fig.6).

- Take the upper chimney piece and x it to

the structure using the 2 screws A (Fig.7).

Join the lower chimney piece with the up-

per one and x it carefully using adhesive

tape L (Fig.8).

- Screw the 2 screws O, max 3 mm (Fig.8).

Insert the exhaust unit inside the structure paying attention that the screws O, hook into

the slots in the lower part as indicated in (Fig.9). Drive in the 6 screws N (supplied) and

tighten the 2 screws O (Fig.9).

- Fix the air evacuation pipe H (not supplied) onto the connection ange F (Fig.10).

- Remove adhesive tape L and rest the lower chimney piece above the cooker hood

(Fig.11).

tLimited to installation on plasterboard walls: make sure that the screws are xed to the

B

X

B

A

Fig.2

Fig.1

- 10 -

B

G

B

C

G

B

C

Fig.4 Fig.5

Fig.3

- 11 -

L

O

A

N

O

N

Max 3 mm

O

Fig.6 Fig.7

Fig.9Fig.8

- 12 -

wall support elements. If this is not the case, install a support structure made up from 2

by 4 inch cross members in correspondence with the screw anchorage points.

IMPORTANT - The range hood must be secured to wall studs or use drywall anchors

capable of supporting 75 lbs.

Fig.11

Fig.10

- 13 -

POWER SUPPLY:

IMPORTANT – (Please read carefully)

WARNING:

FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED.

Remove house fuse or open circuit breaker before beginning installation. Do not use an

extension cord or adapter plug with this appliance. Follow National electrical codes or

prevailing local codes and ordinances.

Electrical supply:

These vent hoods must be supplied with 120V, 60Hz, and connected to an individual,

properly grounded branch circuit, and protected by a 15 or 20 amp circuit breaker or

time delay fuse.

t8JSJOHNVTUCFXJSFXJUIHSPVOE

t*G UIF FMFDUSJDBM TVQQMZ EPFT OPU NFFU UIF BCPWF SFRVJSFNFOUT DBMM B MJDFOTFE

electrician before proceeding.

t3PVUFIPVTF XJSJOHBTDMPTFUPUIFJOTUBMMBUJPO MPDBUJPOBT QPTTJCMFJOUIF DFJMJOHPS

back wall. Refer to Wiring Locations on page 14.

t$POOFDUUIFIPPEXJSJOHUPUIFIPVTFXJSJOHJOBDDPSEBODFXJUIMPDBMDPEFT

Grounding instructions:

The grounding conductor must be connected to a grounded metal, permanent wiring

system, or an equipment-grounding terminal or lead on the hood.

WARNING: The improper connection of the equipment-grounding conductor

can result in a risk of electric shock. Check with a qualied electrician or service repre-

sentative if you are in doubt whether the appliance is properly grounded.

- 14 -

A

B

Fig.12 Fig.13

Fig.12

2. CONNEC T ELECTRICAL:

t1PXFS4VQQMZ$POOFDUJPO

For connection to the power supply refer

to the following Fig.12:

1. Remove the power supply cover by

undoing the (2) screws Fig.12A.

2. Break through the hole on the box

cover.

3. Secure the power supply conduit to the

cover.

4. Connect the wires of the hood to those

of the power supply as described Fig.12B:

BLACK = L line

WHITE = N neutral

GREEN/YELLOW = G ground

- A double-pole switch properly rated

must be installed to provide the range

hood power supply disconnection.

- Connect the electrical conduit to the

Field Wiring Compartment using listed

conduit ttings.

- Carry out the power supplly connection

in accordance with the national electric

- 15 -

Min 27" - Max 32"

36"

code, ANSI/NFPA 70-1999.

5. Insert the wires into the box, then close the box cover, securing it using the screws

that were previously removed.

The appliance must be installed at a minimum height of 27" from an electric cooker stove,

or 32" from gas or combined cooker stoves. If a connection ductwork composed of two

parts is used, the upper part must be placed outside the lower part. Do not connect the

range hood exhaust duct air to the same duct air used to exhaust hot air or fumes from

other appliances other than electrical. Before proceeding with the assembly operations,

remove the anti-grease lter(s) (Fig.13) so that the unit is easier to handle.

3. CONNECT THE DUCTWORK:

- 16 -

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PER-

SONS, OBSERVE THE FOLLOWING: Before making electrical connections to power

supply, the electrical box must be secured in place as indicated in Fig.14.

Before installing the appliance x the electrical box as indicated in Fig.14.

- Lift the electrical plant box Fig.14A.

- Remove the 3 xed screws Fig.14B.

- Position the electrical box so it is in line with the holes of the previously removed screws

Fig.14C and tighten.

C

A

B

Fig.14

- 17 -

a

3.1

3.2

a

c

F

E

F

b

DUCTLESS RECIRCULATING OPTION:

Fig.1: Put together the two parts of the air devia-

tor as shown in picture no 3.1. It may be necessary

to cut the deviator to fit the width of the chimney

as shown in picture 3.2. A sharp blade or Hacksaw

is recommended to trim the plastic.

CARBON FILTER KIT XORFK04: The kit includes an air diverter A, 1 screw and 2 round

lters C.

Fig.2: To remove the two screws E,

to take down the lower chimeny F.

- 18 -

2

1

3

F

E

F

2

a

b

1

Fig.4: To take the upper chimeny F

and to fix it to the structure using the

two screws E.

Fig.5: To join the lower chimney 1 with the up-

per one and to fix it carefully with the adhesive

tape 2. To fix the flexible pipe (6" ROUND FLEX

IBLE METAL DUCT PIPE NOT INCLUDED on

the flange of connection 3.

Fig.6: Remove adhesive tape 2

and rest the lower chimney piece

above the cooker hood.

6" ROUND FLEXIBLE

METAL DUCT PIPE NOT

INCLUDED

6" ROUND

FLEXIBLE

METAL

DUCT PIPE

NOT

INCLUDED

Fig.3: To fix the air diverter A on the support’s

bracket using the screw B as it is shown in

the figure. Once that the air diverter A has

been fixed, it is necessary to connect the

flexible pipe (6" ROUND FLEXIBLE METAL

DUCT PIPE NOT INCLUDED).

- 19 -

c

1

2

1

2

Fig.7: Remove the aluminum panels

by pulling the lever 1 out and pushing

downwards 2.

Fig.8: The lters C must be applied to the

suction unit inside the hood, centering

them inside of it and turning them 90° until

they snap into place.

Fig.9: Put the aluminum panels back in

place (Fig.7).

- 20 -

USE

t*GUIFBQQBSBUVTJTFRVJQQFEXJUIUIF

following controls luminous:

A = LIGHT

B = OFF

C = SPEED I

D = SPEED II

E = SPEED III

F =

AUTOMATIC STOP TIMER - 15 minutes (*)

t By pressing key F for two seconds (with

the hood switched off) the “clean air”

function is activated. This function switch-

es the appliance on for ten minutes every

hour at the rst speed. As soon as this

function is activated the motor starts up

at the rst speed for ten minutes. During this time key F and key C must ash at the same

time. After ten minutes the motor switches o and the LED of key F remains switched on

with a xed light until the motor starts up again at the rst speed after fty minutes and

keys F and C start to ash again for ten minutes and so on. By pressing any key for the

exclusion of the hood light the hood will return immediately to its normal functioning

(e.g. if key D is pressed the “clean air” function is deactivated and the motor moves to

the 2nd speed straight away. By pressing key B the function is deactivated).

(*) The “automatic stop timer” delays stopping of the hood, which will continue func-

tioning for 15 minutes at the operating speed set at the time this function is activated.

t"DUJWFDBSCPOHSFBTFöMUFSTBUVSBUJPO

- When button A ashes at a frequency of 2 seconds, the grease lters must be cleaned.

- When button A ashes at a frequency of 0.5 seconds, the carbon lters must be replaced.

After the clean lter has been replaced, the electronic memory must be reset by pressing

button A for approximately 5 seconds, until the light on the button stops ashing.

ABCDEF

La page charge ...

XO XOBI36SMUA Manuel utilisateur

XO XOBI36SMUA Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents