Hoover HIZ169 Le manuel du propriétaire

Instruction Book

Washing Machine

English

Français

40003289Eng.qxd 03/06/2005 12:12 Page 1

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Delivery information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Do’s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Don’ts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Unpacking the Product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Choose a location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Electricity supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Water supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Connecting to the cold water supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Connection of the machine to the drain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Moving the machine into position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Adjusting the feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Testing the installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Washing advice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Loading your washing machine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Sorting the laundry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

The Dispenser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Detergent dosage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Dispensing instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Using Inter@ct for the first time. . . . . . . . . . . . . . . . . . . . . . . . 17

Programming the machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

The Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Wash Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Automatic Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Programme Selector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Special Programmes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Daily Programmes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Programme Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

A Typical Wash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Selecting the wash programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Starting the wash cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Cleaning and Routine Maintenance. . . . . . . . . . . . . . . . . . . . 34

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Power Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

2

English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Français . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

40003289Eng.qxd 03/06/2005 12:12 Page 2

Introduction

Please read and follow these instructions

carefully and operate the machine accordingly.

This booklet provides important guidelines for

safe use, installation, maintenance and some

useful advice for best results when using your

machine.

Keep all documentation in a safe place for future

reference or for any future owners.

Delivery information

Please check that the following items are

delivered with the appliance:

● Instruction manual

● Guarantee card

● Blanking plug

● Inlet hose & hooked end support

(see Unpacking and Installation Instructions)

● Base panel & x2 push clips

● Energy Label

Do’s

● All packaging materials used are

environmentally-friendly and recyclable.

Please help dispose of the packaging via

environmentally-friendly means. Your local

council will be able to give you details of

current means of disposal.

● To ensure safety when disposing of an old

washing machine disconnect the mains plug

from the socket, cut the mains power cable

and destroy this together with the plug. To

prevent children shutting themselves in the

machine break the door hinges or the door

lock.

● This machine is solely for domestic use,

i.e. to wash, rinse and spin dry household

textiles and garments.

3

Check that no

damage has

occurred to the

machine during

transit. If it has,

call for service

by GIAS.

40003289Eng.qxd 03/06/2005 12:12 Page 3

Don’ts

● Do not touch the appliance when hands or

feet are damp or wet.

● Do not lean on the door when loading the

machine or use the door to lift or move the

machine.

● Do not use adapters, multiple connectors

and/or extensions.

● Do not allow children to play with the

machine or its controls.

● Do not try to open the door when water is

visible in the drum or the Porte Sécurisée

indicator is on.

4

Failure to

comply with

the above can

compromise the

safety of the

appliance. You

may be charged

for a service call

if a problem

with your

machine is

caused by

misuse.

If the appliance

is not running

properly or

breaks down,

switch it off,

disconnect the

plug from the

socket, turn off

the water

supply and do

not tamper

with the

appliance.

Consult GIAS

Service for

possible repair.

40003289Eng.qxd 03/06/2005 12:12 Page 4

Unpacking the product

Remove the machine from its packaging close to

the final location of the machine.

1. Cut carefully around the base of the

packaging.

2. Lay the machine on its back and remove the

base and the two polystyrene spacers on

each side of the machine. We recommend

that a second person assist in the lifting and

manoeuvring of the machine.

3. Return the machine to the upright position,

remove the remainder of the packaging and

the central screw in the transit bar.

4. Remove the four retaining screws in the

transit bar and pull out the transit bracket.

5

Dispose of the packaging safely.

Make sure it is out of the reach

of children, it is a potential

source of danger.

40003289Eng.qxd 03/06/2005 12:12 Page 5

5. Take the base panel provided and fit the

two self adhesive strips by removing the

backing paper on one side and locating the

strips on each side of the base panel.

6. Tilt the machine forward and locate the

base panel under the front of the machine.

Remove the remaining backing paper from

the self-adhesive strips and offer up the

base panel to the bottom of the cabinet.

7. Take the two plastic fixing clips and fix the

base panel to the base of the machine.

Bring the machine back to the upright

position.

6

We recommend you keep the transit bracket and

screws to protect the machine for future transit.

The manufacturers will not be responsible for any

damage to the machine caused by not following the

instructions relating to releasing the transit protection.

The user is responsible for all installation costs.

40003289Eng.qxd 03/06/2005 12:12 Page 6

8. Cover the central hole in the rear of the

machine with the cap enclosed in the

instruction bag.

Choose a location

● After the machine has been installed, ensure

that the mains plug and water supply valves

are easily accessible.

● Make sure there is enough space for the

machine. Select a space at least 600mm wide

and 850mm high. Also leave enough space

to open the door fully so you can load and

unload it easily.

● Keep the area underneath and around the

machine free of combustible materials such

as lint, paper, rags, chemicals etc.

7

Installation

Do not plug the

machine in and

switch it on at

the mains until

the installation

is completed.

40003289Eng.qxd 03/06/2005 12:12 Page 7

Electricity supply

Washing machines are supplied to operate at a

voltage of 230V, 50 Hz single phase. Check that

the supply circuit is rated to at least 16A.

Electricity can be extremely dangerous.

This washing machine must be earthed.

The socket outlet and the plug on the appliance

must be of the same type.

Do not use multiple adapters and/or extension

leads.

The wires in the mains lead are coloured in

accordance with the following codes:

Blue NEUTRAL

Brown LIVE

Green and Yellow EARTH

CE Appliance complies with European Directive

89/336/EEC, 73/23/EEC and subsequent

amendments.

Water supply

● The cold water pressure should be between

0.05-0.8 Mpa.

● Do not connect the machine to a single

outlet instantaneous water heater.

● The water supply tap should be accessible

when the machine is installed.

● Before connecting the fill hose, check that

the water is running from the water supply

tap to be used.

8

You may be

charged for a

service call if a

problem with

your machine is

caused by

incorrect

installation.

If the mains

cord on this

appliance is

damaged, it

must be

replaced by a

special cord

which is ONLY

obtainable from

the GIAS spares

service. It must

be installed by

a competent

person.

40003289Eng.qxd 03/06/2005 12:12 Page 8

This machine has an inlet hose with a 19mm

(3/4") threaded ferrule fitted to the end, to

attach between the threaded connector on the

appliance and the water supply.

Only use the new hose supplied to connect the

machine and ensure that the sealing washers are

in place inside the hose connectors.

Do not re-use old hoses which are attached to

existing installations.

Do not over-tighten the connections. Hand tight

is sufficient.

Do not trap or kink the hose.

1. Connect the elbow end of the hose provided

to the threaded inlet on the back of the

machine.

Grey pipe to the white threaded inlet on

the machine.

2. Hand tighten the connector.

3. Connect the straight ends of the pipes to

the water supply; ensure that there are no

kinks.

4. Turn on the water supply and check for

leaks. If there is a leak, turn off the water

supply, disconnect the hose and check the

sealing washers are in place. Refit the hose

and turn on the water supply.

Aqua-stop

Certain models will be supplied with special hose

that has a double skin and incorporates a water

valve (A). If the inner hose bursts the valve will

automatically shut off the water supply to

prevent flooding. The indicator turns red (B).

Should this happen, turn off the water supply

immediately and obtain a replacement hose from

GIAS Service.

The installation is the same as a conventional

hose with the valve end of the aqua-stop hose

fitted to the water supply.

9

A

B

Connecting to the cold water supply

40003289Eng.qxd 03/06/2005 12:13 Page 9

Connection of the machine to the

drain

This machine must be connected in accordance with the water supply

regulations. Water byelaws prohibit connection to a surface water drain.

Decide which plumbing option suits you best then follow the instructions

below.

Option 1

Waste pipe connection (waste trap)

Fit the hooked end support to the outlet pipe. Position at least 800mm off the

floor.

After removing the blanking plug or cutting the membrane from the waste

system securely fix the outlet pipe to the drainage system, using a hose clip.

Secure the hooked end support up to at least 800mm to avoid water being

drawn back into the machine.

10

All machines are tested with water prior to leaving the

factory so a small amount of water may remain in the

drum and drain hose.

Flooding could occur if any part of the installation is

not completed correctly.

800 mm

hose clip

hooked end support

sink

flexible

discharge hose

trap with hose

adaptor

40003289Eng.qxd 03/06/2005 12:13 Page 10

Option 2

Into a standpipe

Ensure that the standpipe is not located near

an electrical socket.

Fit the hooked end support to the outlet pipe.

Install the hose into the standpipe ensuring

that the pipe is at least 500mm from the floor.

Insert the outlet pipe approximately 100mm

into the standpipe.

Moving the machine

into position

Your machine is heavy so care must be taken

when moving it. We recommend that two people

move the machine to avoid strain and possible

injury.

● Take care not to damage flooring when

moving the machine.

● When moving the machine to its final

position take care not to kink or damage

the hose at the back of the machine.

Adjusting the feet

Once the machine is in place the feet should be

adjusted to ensure that the machine is level. If

the machine is not level it may become noisy or

move.

Adjust the feet on the front corners of the

machine until the machine is firm and level.

When the machine is firm and level, tighten the

locking nuts on the two feet.

11

Do not drag or

lift the machine

by its door.

100 mm

500 mm min

40003289Eng.qxd 03/06/2005 12:13 Page 11

Refer to the programme guide for details of how

to select programmes.

1. Turn on the water supply and check for

leaks from the fill hose.

2. Switch on the electricity supply.

3. Select the Essorage programme (15) and

then press the Départ/Pause button to start

the machine. Allow the programme to

continue for one minute and then cancel

the programme by returning the selector to

the ARRÊT position. This will remove any

water remaining in the machine from

factory testing.

4. To check for cold water filling to the

machine:

Select the Rinçage programme (14) and

press the Départ/Pause button to start the

machine.

Allow the tumble action to continue until

the water has pumped out. Check that the

drain outlet is not leaking or overflowing.

5. Switch off the machine at the end of the

cycle by turning the programme knob to the

ARRÊT position.

6. Select the Essorage programme (15) and

press the Départ/Pause button to start the

machine. If the machine takes longer than

one minute to empty check the drain hose

for kinks.

Installation testing is now

complete.

Now you have successfully installed the machine

we advise that you run the machine to ensure the

drum is thoroughly clean after testing and

storage. Select COTON RESISTANT 90 and run the

machine for a complete cycle using only wash

detergent and water.

12

Testing the installation

This

programme

will take

approximately

2 hours to

complete.

40003289Eng.qxd 03/06/2005 12:13 Page 12

The following tips are designed to assist in

getting the best results from your machine whilst

utilising it in the most environmentally-friendly

and economical way. It is also important to

understand the items to avoid in your laundry, to

ensure the continued safe and reliable operation

of your machine.

Loading your washing

machine

To make further reductions of energy, water and

detergent consumption, we recommend that you

put a full load into your machine. Energy savings

of up to 50% can be achieved by washing one full

load compared to two half loads.

Do not overload the machine as this will reduce

the quality of the wash and may cause damage

to the machine and your laundry.

When is prewashing really

needed?

Only with particularly dirty loads! Energy savings

of 5 to 15% are made by not selecting the

prewash option for less dirty laundry. Pre-treat

awkward stains with a washable stain remover.

Which wash temperature should

you choose?

Using stain removers before machine washing

reduces the need to wash at temperatures over

60°C.

Using a 40°C wash temperature can make energy

savings of up to 50%.

Heavily soiled laundry

To ensure the best performance when washing a

particularly dirty load, we recommend that you

reduce the amount of items to be put into the

machine. Allowing more space in the drum the

13

Washing advice

40003289Eng.qxd 03/06/2005 12:13 Page 13

items can circulate more freely and will wash

cleaner.

Sorting the laundry

Items to avoid

We recommend that you do not wash underwired

bras in the machine. Should the wires become

detached it could cause damage to your clothes

and the machine. If the washcare label states that

the bra is machine washable then we advise

placing it in a wash bag.

Recommendations

Always follow the wash care labelling on the

garments.

Fasten zips, tie strings and close press studs to

prevent tangling. Ensure that pockets are

emptied of loose change and other small items.

Check that there are no metal objects in the

laundry as these may damage the laundry and

the machine.

Place small items in a wash bag.

14

Do not use the

machine to

wash items that

do not have a

wash label.

Do not wash

items

previously

treated with

solvents.

40003289Eng.qxd 03/06/2005 12:13 Page 14

Detergent dosage

Only use detergents which are suitable for use in a washing machine. You will

obtain the best results from your wash with the minimum use of chemical

products, and the best care for your laundry if you take into consideration the

degree of soiling as well as the type of detergent to choose.

The amount of detergent to use depends on:

● Water hardness.

Depending on the hardness of the water and the type of detergent used,

it is possible to reduce the amount of detergent.

The softer the water supply, the less detergent is required.

● The degree of soiling.

It is possible to reduce the amount of detergent used depending on the

degree of soiling.

Use less detergent for less soiled items.

● Amount of laundry.

It is possible to reduce the amount of detergent when washing only a

small amount of laundry.

For smaller loads use less detergent.

The dosages shown on the packaging of detergents for washing delicates

often already refer to a reduced wash size. Always follow the dosage

instructions on the detergent packaging.

15

The Dispenser

DO NOT exceed the maximum detergent dosage

COMPARTMENT I

Prewash detergent

Maximum dosage 100ml of powder

COMPARTMENT II

Mainwash detergent

Maximum dosage 200ml

of powder

COMPARTMENT

Fabric Conditioner

Maximum dosage 100ml

40003289Eng.qxd 03/06/2005 12:13 Page 15

Dispensing instructions

The detergent drawer is split into 3

compartments:

● the first, labelled "I", is for detergent utilised

during Prewash.

● the second, labelled "II", is for detergent

utilised during the main wash.

● the third, labelled is for special

additives such as fabric softeners, fragrances,

starch, brighteners etc.

Dispensing in the drum

Liquid detergents and some tablets are dispensed

via the machine drum using the recommended

dispensing device which is placed upright on top

of the washload towards the back of the drum.

Some tablets are designed to be placed in the

dispenser drawer, check the detergent pack for

details.

16

Do not put any

items into the

drawer other

than detergents

that are

designed to be

dispensed from

the drawer as

they may cause

blockage or

damage.

40003289Eng.qxd 03/06/2005 12:13 Page 16

17

Using Inter@ct for the first

time

This machine will operate even if you do not programme the Inter@ct set up.

However, this machine has Départ Différé and Programmation Fin Du Cycle

functions and for these functions to work efficiently Inter@ct must be

programmed. This is a simple operation and special care has been taken

during manufacture to ensure that the user can operate this machine simply

and effectively.

Programming the machine

Inter@ct needs to be programmed so that the correct clock setting, language

and personal requirements are set.

When the machine is turned on and the programme dial is moved away from

the ARRÊT position to a programme selection a Welcome message will appear.

This message is displayed for a short time while the machine recognises which

programme has been selected. When the machine is ready, the programme

details will appear on the display and from here you may now beging

programming the machine.

Example:

Please note that when using the Inter@ct menu you have 30 seconds per

operation to make your selection. Should you run out of time, the display will

return to the start screen, and you simply have to re-enter the Inter@ct menu

and continue with the programming.

HOOVER INTER@CT

WELCOME 11:06

1 WHITE COTTON

90° HEAVY 1600 RPM

40003289Eng.qxd 03/06/2005 12:13 Page 17

18

To enter the Menu

Hold down the Super Rapide and the Extra Rinçage buttons together for

5 seconds or until the beep sounds.

The menu options can be changed by pressing the Extra Rinçage button. To

confirm and enter an option press the Super Rapide button.

Set New Time

This function needs to be set for two reasons, firstly to display the current

time of day on the screen and secondly for the Programmation Fin Du

Cycle/Départ Différé settings to work correctly.

You will notice in the display window that the hours on the clock will be

flashing. To set the hours you must press the Extra Rinçage button until the

required figure is displayed. Then press the Super Rapide button to enter the

chosen figure. Now the minutes on the clock will begin to flash. Again press

the Extra Rinçage button until the required minutes are displayed and press

Super Rapide to input the selection.

When you have Set the New Time, the display will ask if you wish to Set the

Time Mode.

Setting the time mode (default setting – ABSOLUTE)

The Set Time Mode allows you choose how you wish the Programme Set End

Time and Start Delay functions to be controlled.

The first, called Absolute Time Mode, allows you to set the actual time you

want the programme to begin or end. An example can be seen below when

the Absolute Time Mode has been selected in the menu set-up stage.

In this example, when setting the Programmation Fin Du Cycle the

programme (as shown above) will end at 08.00.

The second, called Relative Time Mode, allows you to delay the start or end of

your wash cycle by adding hours to the current time displayed on the clock, e.g.

Programme to start/end in 1 hour 30 minutes. An example can be seen below

when Relative Time Mode has been selected is the menu set-up stage.

PROGRAMME END

08:00 14:00

40003289Eng.qxd 03/06/2005 12:13 Page 18

19

In this example, when setting the Programmation Fin Du Cycle the

programme (as shown above) will end at 15:30.

Both options are very useful, but Absolute Time Mode is easier to use since

there is no need for you to calculate how many hours to leave before you

want the machine to end or start your chosen cycle.

You can select which option you require by pressing the Extra Rinçage button

until your preferred option is displayed, and then pressing the Super Rapide

button to accept the option you have chosen.

When you have entered your preferred Time Mode, the display will then ask

for Enable Final Beeping to be set.

Enable Final Beeping (default setting – YES)

Here you have the option to have a beeping alarm to let you know the wash

cycle has finished. By pressing the Extra Rinçage button you can scroll through

the YES and NO options.

To confirm your selection press the Super Rapide button and the screen will

then move to the next stage and ask you if you wish to Enable Memory.

Enable Memory (default setting – NO)

This is a useful feature if you frequently wash laundry using the same

programme. Selecting Enable Memory will tell the machine to remember the

last programme/functions used and set them in the memory. This feature

works only on the Cottons, Delicates, Synthetics and Woollens programmes.

The memory does not retain settings within the Special Programmes group.

Select YES or NO by using the Extra Rinçage button and confirm your

selection by pressing the Super Rapide button.

The display will now show a message asking if you require the Demo Mode to

be set. Please set this option to NO if this has not already been done. This

function is for SERVICE use only. If the demo mode option is set to YES, the

wash programme WILL NOT commence when you exit the Inter@ct 3D menu.

The Demo Mode must be set to NO for the wash cycle to commence. Select

NO using the Super Rapide button and confirm your choice with the Extra

Rinçage button. You will then be asked if you wish to Exit the Menu.

PROGRAMME END

BY 1H 30M 14:00

40003289Eng.qxd 03/06/2005 12:13 Page 19

20

Exit Menu

If you are happy with the settings you have selected, you can now exit the

menu by selecting YES via the Extra Rinçage button and confirm this selection

using the Super Rapide button. However, if you are not happy with some of

the settings selected you must select NO and you can then start programming

again from the beginning. By pressing the Super Rapide button you can enter

and bypass each option individually until you reach the option you would like

to change.

When you are completely satisfied with the menu options you have selected,

you may exit the menu. Testing of the installation may now start. If you wish

to change any of the menu settings at a later date, you can enter the menu as

previously described, run through the menu options from the beginning and

change whichever options you wish. This may be useful for changing Set New

Time when Daylight Saving starts or ends.

Once set, the menu options will remain in the memory of the machine even if

the machine is unplugged or there is a power cut.

40003289Eng.qxd 03/06/2005 12:13 Page 20

La page charge ...

Hoover HIZ169 Le manuel du propriétaire

Ce manuel convient également à

Hoover HIZ169 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents