VTech CS6409 Manuel utilisateur

Marque: VTech

Modèle: CS6409

Catégorie: Téléphones

Taper: Manuel utilisateur

User’s manual

Accessory handset for

use with VTech models

CS6419/CS6428/CS6429

www.vtechphones.com

Model: CS6409

Congratulations

on purchasing your new VTech product. Before using this

telephone, please read Important safety instructions

on pages 8 of this manual.

This manual has instructions on how to set up and register your

new handset. For complete instructions on using the handset, see

the user’s manual that came with your telephone base.

If you cannot ﬁnd your user’s manual, you can view or download it at

www.vtechphones.com. In Canada, go to www.vtechcanada.com.

3-month warranty!

Visit www.vtechphones.com.

Registration

warranty support.

Product news

Learn about the latest VTech products.

Telephones identified with this logo have reduced noise

and interference when used with most T-coil equipped

hearing aids and cochlear implants. The TIA-1083 Compliant

Logo is a trademark of the Telecommunications Industry

Association. Used under license.

Compatible with

Hearing Aid T-Coil

TIA-1083

Table of contents

Getting started ............................................................................1

Parts checklist ............................................................................. 1

Battery installation ....................................................................... 2

Battery charging .......................................................................... 3

Add and register a handset ........................................................ 4

Replace a handset ....................................................................... 5

Handset layout ............................................................................ 6

Appendix .....................................................................................8

Important safety instructions ........................................................ 8

Operating range ......................................................................... 12

Maintenance .............................................................................. 12

The RBRC

seal ........................................................................ 13

FCC, ACTA and IC regulations ................................................. 14

California Energy Commission battery charging

testing instructions ................................................................. 17

For C-UL compliance only ......................................................... 18

Limited warranty ........................................................................ 21

Technical speciﬁcations ............................................................. 24

Parts checklist

Your telephone package contains the following items. Save your

sales receipt and original packaging in case it is necessary to ship

your telephone for warranty service.

Handset

User’s manual

Getting started

Charger and charger adapter

BatteryBattery compartment

cover

To purchase a replacement battery or power adapter, visit our

website at www.vtechphones.com or call 1 (800) 595-9511. In

Canada, go to www.vtechcanada.com or call 1 (800) 267-7377.

Getting started

Battery installation

Install the battery as shown below.

Plug the battery connector securely into the socket inside the

handset battery compartment.

Place the battery with the label THIS SIDE UP facing up and the

wires inside the battery compartment.

Align the cover flat against the battery compartment, then slide it

towards the center of the handset until it clicks into place.

Charge the handset by placing it in the telephone base or

charger. The CHARGE light is on when the handset is charging.

CHARGE light

remains on when

charging.

3 4

If the handset will not be used for a long time, disconnect

and remove the battery to prevent possible leakage.

To purchase a replacement battery, visit our website at

www.vtechphones.com or call 1 (800) 595-9511. In Canada,

go to www.vtechcanada.com or dial 1 (800) 267-7377.

•

Battery charging

Once you have installed the battery, the screen indicates the

battery status (see the table below).

For best performance, keep the handset in the telephone base

or charger when not in use.

The battery is fully charged after 10 hours of continuous

charging.

If you place the handset in the telephone base or the charger

without plugging in the battery, the screen displays NO BATTERY.

•

Getting started

Battery indicators Battery status Action

The screen is blank,

or shows

PLACE IN CHARGER

and flashes.

Battery has no

charge or very

little charge. The

handset cannot

be used.

Charge without

interruption (at least

30 minutes).

The screen shows

LOW BATTERY and

flashes.

Battery has

enough charge to

be used for a

short time.

Charge without

interruption (at least

30 minutes).

The screen shows

HANDSET X.

Battery is charged. To keep the battery

charged, place it in the

telephone base or charger

when not in use.

When the battery is fully charged, you can expect the following

performance:

Operation Operating time

While in handset use (talking*) Up to seven hours

While in speakerphone mode (talking*) Up to four hours

While not in use (standby**) Up to five days

*Operating times vary depending on your actual use and the age of the battery.

**Handset is not charging or in use.

SET DATE

--/--/--

After you install your telephone or power returns

following a power outage, the handset will

prompt you to set the date and time. To skip

setting the date and time, press OFF/CANCEL.

Add and register a handset

Each new handset (CS6409) must be registered with the

telephone base before use. When first purchased, each

expansion handset shows 1.PRESS FIND HS ON BASE 4 SEC

and 2.THEN PRESS # ON HANDSET alternately. You may need

to charge the handset before registering it to the telephone base.

For more details on battery charging, see the table on page 3.

To register a handset:

Place the unregistered handset in the telephone base or

charger. If 1.PRESS FIND HS ON BASE 4 SEC and

2.THEN PRESS # ON HANDSET do not appear alternately

on the handset screen after a few seconds, remove the

handset and place it in the telephone base or charger again.

On the telephone base, press and hold

/FIND HANDSET for about four seconds

until the red IN USE light on the telephone base

turns on.

On the handset, press # (pound key) and the

handset shows REGISTERING.....

PLEASE WAIT. The handset shows HANDSET REGISTERED

and you hear a beep when the registration process completes.

It takes about 60 seconds to complete.

When the registration process is complete, the newly registered

handset is assigned the next available handset registration

number. For instance, if you already have HANDSET 1, the next

registered handset will be HANDSET 2.

Getting started

If the registration fails, the handset shows REGISTRATION

FAILED, then the handset shows 1.PRESS FIND HS ON BASE

4 SEC and 2.THEN PRESS # ON HANDSET alternately. To

reset the handset, remove the handset from the telephone

base and place it back in. Try the registration process again.

You cannot register a handset if any other system handset

is in use.

To reset the telephone, unplug the power and the battery for

a few seconds then plug them back in.

Only one handset can register to the telephone base at a time.

•

Replace a handset

If you want to replace a handset or reassign the designated

handset number of a registered handset, you must deregister all

the handsets and then individually register each handset.

To make deregistration easier, read all of the instructions below

before you begin.

To deregister all handsets:

Press and hold /FIND HANDSET on the telephone base for

about 10 seconds until the IN USE light on the telephone base

turns on and starts to flash.

Press and release /FIND HANDSET again. You must press

/FIND HANDSET while the IN USE light is still flashing. The

IN USE light flashes for approximately five seconds. If the light

stops flashing, start again at Step 1.

The deregistration process takes about 10 seconds to

complete. All handsets show 1.PRESS FIND HS ON BASE 4

SEC and 2.THEN PRESS # ON HANDSET alternately when

the deregistration process completes.

If deregistration fails, you may need to reset the telephone and

try again.

To reset:

Pick up the registered handset and then press /FLASH.

Press OFF/CANCEL and place the handset back in the

telephone base.

-OR-

Unplug the power from the telephone base, then plug it back in.

•

You cannot deregister handsets if any other system handset is

in use.

You cannot deregister handsets if any other system handset is

in use.

Getting started

/VOLUME

Press to enter the directory when the

telephone is not in use.

Press to scroll up while in a menu, or in

the directory, call log or redial list.

During a call, press to increase the

listening volume.

During message playback, press to increase

the listening volume (for handsets registered to

CS6428 and CS6429 base only).

When entering numbers or names in the

directory, press to move the cursor to the right.

Handset layout

Getting started

(speakerphone)

Press to make or

answer a call.

During a call, press

to switch between the

speakerphone and

the handset.

CHARGE light

On when the handset is charging in the

telephone base or charger.

MUTE/DELETE

While on a call, press to mute the microphone.

While using the dialing keys, press to delete

digits or characters.

While the handset is ringing, press to silence

the ringer temporarily.

When reviewing the redial list, directory or call

log, press to delete the displayed entry.

/FLASH

Press to make or answer a call.

During a call, press to answer an incoming call

when you receive a call waiting alert.

While reviewing a call log entry, press repeatedly

to add or remove 1 in front of the call log entry

before dialing or saving it to the directory.

TONE

Press to switch to tone dialing temporarily when

using the pulse service.

Handset layout

Getting started

MENU/SELECT

Press to show the menu.

While in a menu, press to select an item, or

save an entry or setting.

OFF/CANCEL

During a call, press to hang up.

While the handset is ringing, press to silence

the ringer temporarily.

While the telephone is not in use, press and hold

to erase the missed call indicator.

While in a menu, press to exit to the previous

menu, or press and hold to exit to idle mode.

#( pound key)

Press repeatedly to show other dialing options

when reviewing a call log entry.

INT (intercom)

Press to start an intercom conversation or transfer a call.

REDIAL/PAUSE

Press to review the redial list.

While dialing or entering numbers into the directory,

press and hold to insert a dialing pause.

CID /VOLUME

Press to review the call log when the telephone

is not in use.

Press to scroll down while in a menu, or in the

directory, call log or redial list.

During a call, press to decrease the listening

volume.

During message playback, press to decrease

the listening volume (for handsets registered to

CS6428 and CS6429 base only).

When entering numbers or names in the

directory, press to move the cursor to the left.

Dialing keys

Press to enter numbers or characters.

Important safety instructions

When using your telephone equipment, basic safety precautions should always be

followed to reduce the risk of fire, electric shock and injury, including the following:

Read and understand all instructions.

Follow all warnings and instructions marked on the product.

Unplug this product from the wall outlet before cleaning. Do not use liquid or

aerosol cleaners. Use a damp cloth for cleaning.

Do not use this product near water such as near a bath tub, wash bowl, kitchen

sink, laundry tub or swimming pool, or in a wet basement or shower.

Do not place this product on an unstable table, shelf, stand or other

unstable surfaces.

Avoid placing the telephone system in places with extreme temperature, direct

sunlight, or other electrical devices. Protect your phone from moisture, dust,

corrosive liquids and fumes.

Slots and openings in the back or bottom of the telephone base and handset are

provided for ventilation. To protect them from overheating, these openings must

not be blocked by placing the product on a soft surface such as a bed, sofa or

rug. This product should never be placed near or over a radiator or heat register.

This product should not be placed in any area where proper ventilation is

not provided.

This product should be operated only from the type of power source indicated on

the marking label. If you are not sure of the type of power supply in your home or

office, consult your dealer or local power company.

Do not allow anything to rest on the power cord. Do not install this product where

the cord may be walked on.

Never push objects of any kind into this product through the slots in the telephone

base or handset because they may touch dangerous voltage points or create a

short circuit. Never spill liquid of any kind on the product.

To reduce the risk of electric shock, do not disassemble this product, but take

it to an authorized service facility. Opening or removing parts of the telephone

base or handset other than specified access doors may expose you to dangerous

voltages or other risks. Incorrect reassembling can cause electric shock when the

product is subsequently used.

Do not overload wall outlets and extension cords.

10.

11.

12.

Appendix

Unplug this product from the wall outlet and refer servicing to an authorized

service facility under the following conditions:

When the power supply cord or plug is damaged or frayed.

If liquid has been spilled onto the product.

If the product has been exposed to rain or water.

If the product does not operate normally by following the operating

instructions. Adjust only those controls that are covered by the operation

instructions. Improper adjustment of other controls may result in damage

and often requires extensive work by an authorized technician to restore the

product to normal operation.

If the product has been dropped and the telephone base and/or handset has

been damaged.

If the product exhibits a distinct change in performance.

14. Avoid using a telephone (other than cordless) during an electrical storm. There is

a remote risk of electric shock from lightning.

15. Do not use the telephone to report a gas leak in the vicinity of the leak. Under

certain circumstances, a spark may be created when the adapter is plugged into

the power outlet, or when the handset is replaced in its cradle. This is a common

event associated with the closing of any electrical circuit. The user should not

plug the phone into a power outlet, and should not put a charged handset into

the cradle, if the phone is located in an environment containing concentrations

of flammable or flame-supporting gases, unless there is adequate ventilation. A

spark in such an environment could create a fire or explosion. Such environments

might include: medical use of oxygen without adequate ventilation; industrial

gases (cleaning solvents; gasoline vapors; etc.); a leak of natural

gas; etc.

16. Only put the handset of your telephone next to your ear when it is in normal

talk mode.

17. The power adapter is intended to be correctly oriented in a vertical or floor mount

position. The prongs are not designed to hold the plug in place if it is plugged into

a ceiling, under-the-table or cabinet outlet.

SAVE THESE INSTRUCTIONS

13.

•

Important safety instructions

Appendix

Battery

CAUTION: Use Only Supplied Battery.

Do not dispose of the battery in a fire. Check with local waste management

codes for special disposal instructions.

Do not open or mutilate the battery. Released electrolyte is corrosive and

may cause burns or injury to the eyes or skin. The electrolyte may be toxic if

swallowed.

Exercise care in handling batteries in order not to create a short circuit with

conductive materials.

Charge the battery provided with or identified for use with this product only in

accordance with the instructions and limitations specified in this manual.

Precautions for users of implanted cardiac pacemakers

Cardiac pacemakers (applies only to digital cordless telephones):

Wireless Technology Research, LLC (WTR), an independent research entity, led a

multidisciplinary evaluation of the interference between portable wireless telephones

and implanted cardiac pacemakers. Supported by the U.S. Food and Drug

Administration, WTR recommends to physicians that:

Pacemaker patients

Should keep wireless telephones at least six inches from the pacemaker.

Should NOT place wireless telephones directly over the pacemaker, such as in a

breast pocket, when it is turned ON.

Should use the wireless telephone at the ear opposite the pacemaker.

WTR’s evaluation did not identify any risk to bystanders with pacemakers from other

persons using wireless telephones.

•

Important safety instructions

Appendix

About cordless telephones

Privacy: The same features that make a cordless telephone convenient create

some limitations. Telephone calls are transmitted between the telephone

base and the cordless handset by radio waves, so there is a possibility that

the cordless telephone conversations could be intercepted by radio receiving

equipment within range of the cordless handset. For this reason, you should not

think of cordless telephone conversations as being as private as those on

corded telephones.

Electrical power: The telephone base of this cordless telephone must be

connected to a working electrical outlet. The electrical outlet should not be

controlled by a wall switch. Calls cannot be made from the cordless handset if the

telephone base is unplugged, switched off or if the electrical power is interrupted.

Potential TV interference: Some cordless telephones operate at frequencies

that may cause interference to televisions and VCRs. To minimize or prevent

such interference, do not place the telephone base of the cordless telephone

near or on top of a TV or VCR. If interference is experienced, moving the

cordless telephone farther away from the TV or VCR often reduces or eliminates

the interference.

Rechargeable batteries: Exercise care in handling batteries in order not to

create a short circuit with conducting material such as rings, bracelets, and keys.

The battery or conductor may overheat and cause harm. Observe proper polarity

between the battery and the battery charger.

Nickel-metal hydride rechargeable batteries: Dispose of these batteries in

a safe manner. Do not burn or puncture the battery. Like other batteries of this

type, if burned or punctured, they could release caustic material which could

cause injury.

•

Important safety instructions

Operating range

This cordless telephone operates with the maximum power allowed by the Federal

Communications Commission (FCC). Even so, this handset and telephone base can

communicate over only a certain distance - which can vary with the locations of the

telephone base and handset, the weather, and the layout of your home or office.

When the handset is out of range, the handset displays OUT OF RANGE OR

NO PWR AT BASE.

If there is a call while the handset is out of range, it might not ring, or if it does

ring, the call might not connect well when you press /FLASH. Move closer to the

telephone base, then press /FLASH to answer the call.

If the handset moves out of range during a telephone conversation, there might

be interference.

To improve reception, move closer to the telephone base.

Appendix

Maintenance

Taking care of your telephone

Your telephone contains sophisticated electronic parts, so it must be treated

with care.

Avoid rough treatment

Place the handset down gently.

Save the original packing materials to protect your telephone if you ever need to

ship it.

Avoid water

Your telephone can be damaged if it gets wet. Do not use the handset in the rain,

or handle it with wet hands. Do not install the telephone base near a sink, bathtub

or shower.

Electrical storms

Electrical storms can sometime cause power surge harmful to electronic

equipment. For your own safety, take caution when using electric appliances

during storms.

Cleaning your telephone

Your telephone has a durable plastic casing that should retain its luster for many

years. Clean it only with a soft cloth slightly dampened with water or mild soap.

Do not use excess water or cleaning solvents of any kind.

•

Remember that electrical appliances can cause serious injury if used when

you are wet or standing in water. If the telephone base should fall into water,

DO NOT RETRIEVE IT UNTIL YOU UNPLUG THE POWER CORD AND

TELEPHONE LINE CORDS FROM THE WALL. Then pull the telephone out by

the unplugged cords.

The RBRC

seal

The RBRC

seal on the nickel-metal hydride battery indicates that VTech

Communications, Inc. is voluntarily participating in an industry program to collect

and recycle these batteries at the end of their useful lives, when taken out of service

within the United States and Canada.

The RBRC

program provides a convenient alternative to placing used nickel-metal

hydride batteries into the trash or municipal waste, which may be illegal in your area.

VTech’s participation in RBRC

makes it easy for you to drop off the spent battery

at local retailers participating in the RBRC

program or at authorized VTech product

service centers. Please call 1 (800) 8 BATTERY

for information on Ni-MH battery

recycling and disposal bans/restrictions in your area. VTech’s involvement in this

program is part of its commitment to protecting our environment and conserving

natural resources.

RBRC

and 1 (800) 8 BATTERY

are registered trademarks of Rechargeable

Battery Recycling Corporation.

Appendix

FCC, ACTA and IC regulations

FCC Part 15

This equipment has been tested and found to comply with the requirements for a

Class B digital device under Part 15 of the Federal Communications Commission

(FCC) rules. These requirements are intended to provide reasonable protection

against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used

in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in

a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or more of the

following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications to this equipment not expressly approved by the party

responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may

cause undesired operation. Privacy of communications may not be ensured when

using this telephone.

To ensure safety of users, the FCC has established criteria for the amount of radio

frequency energy that can be safely absorbed by a user or bystander according to

the intended usage of the product. This product has been tested and found to comply

with the FCC criteria. The handset may be safely held against the ear of the user.

The telephone base shall be installed and used such that parts of the user’s body

other than the hands are maintained at a distance of approximately 20 cm (8 inches)

or more.

This Class B digital apparatus complies with Canadian requirement:

CAN ICES-3 (B)/NMB-3(B).

•

Appendix

FCC, ACTA and IC regulations

Part 68 and ACTA

This equipment complies with Part 68 of the FCC rules and with technical

requirements adopted by the Administrative Council for Terminal Attachments

(ACTA). The label on the back or bottom of this equipment contains, among other

things, a product identifier in the format US:AAAEQ##TXXXX. This identifier must be

provided to your local telephone company upon request.

The plug and jack used to connect this equipment to premises wiring and the telephone

network must comply with applicable Part 68 rules and technical requirements adopted

by ACTA. A compliant telephone cord and modular plug is provided with this product.

It is designed to be connected to a compatible modular jack that is also compliant. An

RJ11 jack should normally be used for connecting to a single line and an RJ14 jack for

two lines. See the installation instructions in the user’s manual.

The Ringer Equivalence Number (REN) is used to determine how many devices you

may connect to your telephone line and still have them ring when you are called. The

REN for this product is encoded as the 6th and 7th characters following the US: in

the product identifier (e.g., if ## is 03, the REN is 0.3). In most, but not all areas, the

sum of all RENs should be five (5.0) or less. For more information, please contact

your local telephone company.

This equipment may not be used with Party Lines. If you have specially wired alarm

dialing equipment connected to your telephone line, ensure the connection of this

equipment does not disable your alarm equipment. If you have questions about what

will disable alarm equipment, consult your telephone company or a qualified installer.

If this equipment is malfunctioning, it must be unplugged from the modular jack until

the problem has been corrected. Repairs to this telephone equipment can only be

made by the manufacturer or its authorized agents. For repair procedures, follow the

instructions outlined under the Limited warranty.

If this equipment is causing harm to the telephone network, the telephone company

may temporarily discontinue your telephone service. The telephone company is

required to notify you before interrupting service. If advance notice is not practical,

you will be notified as soon as possible. You will be given the opportunity to correct

the problem and the telephone company is required to inform you of your right to file a

complaint with the FCC. Your telephone company may make changes in its facilities,

equipment, operation, or procedures that could affect the proper functioning of this

product. The telephone company is required to notify you if such changes are planned.

If this product is equipped with a corded or cordless handset, it is hearing

aid compatible.

If this product has memory dialing locations, you may choose to store emergency

telephone numbers (e.g., police, fire, medical) in these locations. If you do store or

test emergency numbers, please:

Remain on the line and briefly explain the reason for the call before hanging up.

Perform such activities in off-peak hours, such as early morning or late evening.

Appendix

FCC, ACTA and IC regulations

Industry Canada

Operation is subject to the following two conditions: (1) this device may not cause

harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Privacy of communications may not be ensured when using this phone.

The term ‘’IC:‘’ before the certification/registration number only signifies that the

Industry Canada technical specifications were met.

The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. The REN

is an indication of the maximum number of devices allowed to be connected to a

telephone interface. The termination on an interface may consist of any combination

of devices subject only to the requirement that the sum of the RENs of all the devices

does not exceed five.

This product meets the applicable Industry Canada technical specifications.

Appendix

California Energy Commission battery charging testing

instructions

This telephone is set up to comply with the energy-conserving standards right

out of the box. These instructions are intended for California Energy Commission

(CEC) compliance testing only. When the CEC battery charging testing mode is

activated, all telephone functions, except battery charging, will be disabled.

To activate the CEC battery charging testing mode:

Unplug the telephone base power adapter from the power outlet. Make sure all

handsets are plugged with charged batteries.

While you press and hold /FIND HANDSET, plug the telephone base power

adapter back to the power outlet.

After about 20 seconds, when the IN USE light starts ﬂashing, release

/FIND HANDSET and then press it again within 2 seconds.

When the phone successfully enters the CEC battery charging testing

mode, the IN USE light turns off and all handsets display 1.PRESS FIND

HS ON BASE 4 SEC and 2.THEN PRESS # ON HANDSET alternately.

When the phone fails to enter this mode, repeat Step 1 through Step 3

above.

Note: The telephone base will be powered up as normal if you fail to press

/FIND HANDSET within 2 seconds in Step 3.

To deactivate the CEC battery charging testing mode:

Unplug the telephone base adapter from the power outlet, then plug it back in.

Then the telephone base is powered up as normal.

registration instructions.

La page charge ...

VTech CS6409 Manuel utilisateur

Marque: VTech

Modèle: CS6409

Catégorie: Téléphones

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: VTech CS6409 User manual

VTech CS6409 Manuel utilisateur

VTech CS6409 Manuel utilisateur

dans d''autres langues

Documents connexes