Dometic RMD10 Guide d'installation

RMD10.5

Absorber refrigerator

Installation Manual. . . . . . . . . . . . . . . . . . . . 13

Réfrigérateur à absorption

Instructions de montage . . . . . . . . . . . . . . .28

EN

FR

FOR YOUR SAFETY

If you smell gas:

1. Open window.

2. Don‘t touch electrical switches.

3. Extinguish any open flame.

4. Immediately call your gas supplier.

FOR YOUR SAFETY

Do not store or use gasoline or other

flammable vapors and liquids in the

vicinity of this or any other appliance.

WARNING: Improper installation,

adjustment, alteration, service or

maintenance can cause injury or

property damage. Refer to this manual.

For assistance or additional information

consult a qualified installer, service

agency or the gas supplier.

REFRIGERATION

10-SERIES

DometicRMD10.5_INM_4445102585_AMER(en-fr)_202x-xx-xx.book Seite 1 Donnerstag, 28. Januar 2021 7:27 19

protected by copyright and design law. The underlying technical design and the

products contained herein may be protected by design, patent or be patent

pending. The trademarks mentioned in this manual belong to Dometic Sweden AB.

All rights are reserved.

DometicRMD10.5_INM_4445102585_AMER(en-fr)_202x-xx-xx.book Seite 2 Donnerstag, 28. Januar 2021 7:27 19

RMD10

3

NOTICENOTICE

d 90°

523 mm

20.59 in.

1245 mm

49.06 in.

550 mm

21.65 in.

523 mm

20.59 in.

1245 mm

49.06 in.

605 mm

23.82 in.

RMD 10.5(S)(T)

RMD 10.5X(T)(S)

1

DometicRMD10.5_INM_4445102585_AMER(en-fr)_202x-xx-xx.book Seite 3 Donnerstag, 28. Januar 2021 7:27 19

RMD10

4

2

1

2

≥ 1250 mm

≥ 49.21 in.

< 1250 mm

< 49.21 in.

1

3

DometicRMD10.5_INM_4445102585_AMER(en-fr)_202x-xx-xx.book Seite 4 Donnerstag, 28. Januar 2021 7:27 19

RMD10

5

15 – 25 mm

0.59 in. – 0.98 in.

> 25 mm

> 0.98 in.

> 25 mm

> 0.98 in.

4

≥ 1800 mm

≥ 70.87 in.

15 – 25 mm

0.59 in. – 0.98 in.

1

5

DometicRMD10.5_INM_4445102585_AMER(en-fr)_202x-xx-xx.book Seite 5 Donnerstag, 28. Januar 2021 7:27 19

RMD10

6

≥ 300 mm

≥ 11.81 in.

1 2

6

DometicRMD10.5_INM_4445102585_AMER(en-fr)_202x-xx-xx.book Seite 6 Donnerstag, 28. Januar 2021 7:27 19

RMD10

7

A

3

1

2

B

< 5 mm (1.97 in.)

5 – 10 mm

C

1

4

(1.97 – 3.94 in.)

7

DometicRMD10.5_INM_4445102585_AMER(en-fr)_202x-xx-xx.book Seite 7 Donnerstag, 28. Januar 2021 7:27 19

RMD10

8

t 40 mm (1.57 in.)

1

2

8

3

2

1

4

9

DometicRMD10.5_INM_4445102585_AMER(en-fr)_202x-xx-xx.book Seite 8 Donnerstag, 28. Januar 2021 7:27 19

RMD10

9

0

a

1.

2.

3.

b

1

2

c

d

DometicRMD10.5_INM_4445102585_AMER(en-fr)_202x-xx-xx.book Seite 9 Donnerstag, 28. Januar 2021 7:27 19

RMD10

10

e

f

1

2

g

2

1

3

h

DometicRMD10.5_INM_4445102585_AMER(en-fr)_202x-xx-xx.book Seite 10 Donnerstag, 28. Januar 2021 7:27 19

RMD10

11

X32

X12

X13

X07

X15

X2X1

X22

X20 X17

X16

X15

X09

X30

X3

X6

2A Fuse

X4

X32

wh

(

+

)

bn

(–)

vt (bu)

S+ Optional

L

N

Interface RS232

gy (gn)

D+ (wh)

rd (+)

pk (bu) (+)

bk (–)

86

bn (–)

bn(–)

bn

rd (+)

12V DC Internal

rd (+)

bk (-)

bk (–)

bk

NTC2

ye (wh) (+)

wh (ye) (+)

wh

rd (+) rd (+)

E BAD C F

E

BA

D

C

F

NTC1

20A

rd

30

87

85

1

2

5

4

7

6

8

3

9

10

11

13

14

15

16

20

12

17

18

19

21

22 23 24

N PE L

NEMA 5

i

DometicRMD10.5_INM_4445102585_AMER(en-fr)_202x-xx-xx.book Seite 11 Donnerstag, 28. Januar 2021 7:27 19

RMD10

12

bk bn bu rd pk vt wh

EN Black Brown Blue Red Pink Violet White

FR Noir Marron Bleu Rouge Rosa Violeta Blanc

DometicRMD10.5_INM_4445102585_AMER(en-fr)_202x-xx-xx.book Seite 12 Donnerstag, 28. Januar 2021 7:27 19

EN

RMD10 Explanation of symbols

13

Please read these instructions carefully and follow all instructions, guidelines, and warnings included in this product manual in order to ensure

that you install, use, and maintain the product properly at all times. These instructions MUST stay with this product.

By using the product, you hereby confirm that you have read all instructions, guidelines, and warnings carefully and that you understand and

agree to abide by the terms and conditions as set forth herein. You agree to use this product only for the intended purpose and application

and in accordance with the instructions, guidelines, and warnings as set forth in this product manual as well as in accordance with all appli-

cable laws and regulations. A failure to read and follow the instructions and warnings set forth herein may result in an injury to yourself and

others, damage to your product or damage to other property in the vicinity. This product manual, including the instructions, guidelines, and

warnings, and related documentation, may be subject to changes and updates. For up-to-date product information, please visit

dometic.com.

Table of contents

1 Explanation of symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

2 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

3 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

4 Installing the refrigerator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

5 Connecting the refrigerator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

6 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

1 Explanation of symbols

!

A

I

WARNING!

Safety instruction: Indicates a hazardous situation that, if not avoided,

could result in death or serious injury.

CAUTION!

Safety instruction: Indicates a hazardous situation that, if not avoided,

could result in minor or moderate injury.

NOTICE!

Indicates a situation that, if not avoided, can result in property damage.

NOTE

Supplementary information for operating the product.

DometicRMD10.5_INM_4445102585_AMER(en-fr)_202x-xx-xx.book Seite 13 Donnerstag, 28. Januar 2021 7:27 19

EN

Safety instructions RMD10

14

2 Safety instructions

The manufacturer accepts no liability for damage in the following cases:

• Faulty assembly or connection

• Damage to the product resulting from mechanical influences and incorrect

connection voltage

• Alterations to the product without express permission from the manufacturer

• Use for purposes other than those described in the operating manual

!

WARNING! Failure to obey these warnings could result in death

or serious injury.

Explosion hazard

• Never open the absorber unit. It is under high pressure and can cause

injury if it is opened.

• Only operate the device at the pressure shown on the type plate.

Only use pressure controllers with a fixed setting which comply with

the national regulations (in Europe EN 12864).

Fire hazard

• Ensure clean and residue-free handling if silicon sealant or similar is

used. There is a risk of fire if silicone filaments come into contact with

hot parts or naked flames.

• Never use a naked flame to check the device for leaks.

• Only use propane or butane gas (not natural gas).

Health hazard

• Do not operate the device if it is visibly damaged.

• If the AC power cable for this device is damaged, it must be replaced

by the manufacturer, a service agent or a similarly qualified person in

order to prevent safety hazards.

• This device may only be repaired by qualified personnel. Inadequate

repairs may cause serious hazards.

Risk of asphyxiation

• Dismantle all device doors for the disposal of the old device and leave

the shelves in the device to prevent accidental enclosure and suffoca-

tion.

DometicRMD10.5_INM_4445102585_AMER(en-fr)_202x-xx-xx.book Seite 14 Donnerstag, 28. Januar 2021 7:27 19

EN

RMD10 Safety instructions

15

!

CAUTION! Failure to obey these cautions could result in minor or

moderate injury.

Electrical shock

• Before starting the device, ensure that the power supply line and the

plug are dry.

Risk of crushing

• Do not put your fingers into the hinge.

A

NOTICE! Damage hazard

• Only hold the device at the body of the device during transport. Never

hold the device at the absorber unit, the cooling fins, the gas pipes,

the door or the control panel.

• Make sure that the device circuit is not damaged during

transportation. The refrigerant in the device circuit is highly

flammable.

In the event of any damage to the device circuit (smell of ammonia):

– Switch off the device if applicable.

– Avoid naked flames and sparks.

– Air the room well.

• Do not install the device near naked flames or other heat sources (heat-

ers, direct sunlight, gas ovens etc.).

• Danger of overheating!

Always ensure sufficient ventilation so that the heat generated during

operation can dissipate. Make sure that the device is sufficiently far

away from walls and other objects so that the air can circulate.

• Check that the voltage specification on the type plate is the same as

that of the power supply.

• Do not open the refrigerant circuit under any circumstances.

• Only use the AC connection cable supplied to connect the device to

the AC mains.

• Only use cables with a suitable size.

• Never pull the plug out of the socket by the connection cable.

• The device may not be exposed to rain.

DometicRMD10.5_INM_4445102585_AMER(en-fr)_202x-xx-xx.book Seite 15 Donnerstag, 28. Januar 2021 7:27 19

EN

Accessories RMD10

16

3Accessories

4 Installing the refrigerator

The device is suitable for installation in:

• caravans

• motor homes

The refrigerators outlined herein have been design certified by the CSA under the

current edition of ANSI Refrigerator Standard for installation in a mobile home or

recreational vehicle. The certifications are, however, contingent on the installation

being made in accordance with the following instructions as applicable.

In the USA, the installation must conform with:

• National Fuel Gas Code ANSI Z223.1 – (current edition)

• Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280

• Recreational Vehicles ANSI A119.2 – (current edition)

In Canada, the installation must conform with:

• Current CSA B 149.1 Natural Gas and Propane Installation Code

• Current CSA Standard Z 240.4 GAS-EQUIPPED RECREATIONAL VEHICLES

AND MOBILE-HOUSING

• Any applicable local code

Description

Seal for draft-proof installation for gaps of 1 – 5 mm (0.04 – 0.2 in.) (fig. 7 B, page 7)

Seal for draft-proof installation for gaps of 5 – 10 mm (0.2 – 0.39 in.) (fig. 7 C, page 7)

Winter cover LS300 for the ventilation grill

Optional Battery Pack R10-BP for stand-alone gas operation

You find the instructions manual for changing the door lock and the

decorative plate online at:

documents.dometic.com/?object_id=63258

DometicRMD10.5_INM_4445102585_AMER(en-fr)_202x-xx-xx.book Seite 16 Donnerstag, 28. Januar 2021 7:27 19

EN

RMD10 Installing the refrigerator

17

4.1 Preparing the installation

A

When installing the refrigerator, note the following:

• To enable the refrigerant to circulate properly, the refrigerator may not exceed an

angle of 3 °.

Park the vehicle horizontally for this purpose.

• The refrigerator must be installed so that

– it is easily accessible for service work

– easy to de-install and install

– can be easily removed from the vehicle

• The refrigerator must be installed in a recess so that it stands firm when the vehicle

is in motion. Note the dimensions in fig. 1, page 3

for this purpose.

• The outer wall must be fitted with an air inlet vent (fig. 2 1, page 4) and an outlet

vent (fig. 2 2, page 4) with ventilation grills so that the heat generated can be

easily released to the outside:

– Air inlet vent: Fit ventilation grill as flush as possible with the base of the

installation niche.

– Outlet vent: fit as far above the refrigerator as possible.

– The distance between the air inlet and outlet vents must be at least 1250 mm

(49.21 in.) (fig. 3, page 4).

• Fit a heat conduction plate (fig. 3 1, page 4) above the refrigerator so that the

heat does not accumulate in the vehicle.

• The distance between the refrigerator and the rear wall must be at least 15 mm

(0.59 in.) but no more than 25 mm (0.98 in.).

• A distance of more than 25 mm (0.98 in.) between the refrigerator and rear wall

leads to poor performance and increases the power consumption of the refriger-

ator. Reduce the space behind the refrigerator to create adequate air inlet and

outlet ventilation (fig. 4, page 5). Use a ventilation plate, for example, to do

this.

NOTICE!

• The refrigerator may not be installed in the rear of mobile homes with

the door pointing in the direction of travel.

• Use exclusively original Dometic ventilation grills to ensure safe

operation.

DometicRMD10.5_INM_4445102585_AMER(en-fr)_202x-xx-xx.book Seite 17 Donnerstag, 28. Januar 2021 7:27 19

EN

Installing the refrigerator RMD10

18

• If the minimum distance between the air inlet and outlet vents cannot be met, a

roof vent must be installed instead of the air outlet vent.

– The roof vent should be installed directly above the back of the refrigerator as

far as this is possible. Use an air duct (fig. 5 1, page 5) if you need to install

the roof vent offset; otherwise, heat will accumulate there.

– The distance between the air inlet vent and the roof vent must be at least

1800 mm (70.87 in.) (fig. 5, page 5).

– If a roof air conditioner is provided, the distance between the roof vent

(fig. 6 1, page 6) and the air outlet of the roof air conditioner (fig. 6 2,

page 6) must be at least 300 mm (70.87 in.).

• The refrigerator must not be installed at the side of the air inlet and outlet vents as

this leads to poor performance and increases the power consumption of the

refrigerator.

• The air inlet and outlet vents must not be covered by vehicle parts (such as an

open door or by installing accessories such as bicycle racks) while operating.

• Install the refrigerator so that it is protected from excessive heat, as this leads to

poor performance and increases the power consumption of the refrigerator.

• The refrigerator must be installed in a draft-proof location.

4.2 Installing the refrigerator in a draft-proof location

!

Gas-powered refrigerators in camper vans or mobile homes must be installed in a

draft-free location. This means that the combustion air is not extracted from the inte-

rior and the exhaust fumes are prevented from directly entering the living space.

A suitable seal must be fitted between the rear panel of the refrigerator and the

interior of the vehicle.

The manufacturer recommends using a flexible seal to ease removal and installation

for maintenance purposes.

WARNING! Fire hazard!

• Do not use flammable materials such as silicone sealants, foam or

similar for the draft-proof installation.

• Position the device so that no connection cable is damaged or

pinched.

• Do not use multiple sockets or portable power adapters behind the

device.

DometicRMD10.5_INM_4445102585_AMER(en-fr)_202x-xx-xx.book Seite 18 Donnerstag, 28. Januar 2021 7:27 19

EN

RMD10 Installing the refrigerator

19

Select one of the three versions for draft-proof installation (fig. 7, page 7):

Stop bar behind the fridge (A)

➤ Glue a flexible sealing lip (1) to a stop bar (2) behind the refrigerator (3).

➤ Push the refrigerator combination against the stop bar with the flexible sealing

lips.

✔ The space behind the refrigerator is sealed to the interior of the vehicle.

Side gap distance of up to 5 mm (0.2 in.) between refrigerator and

furniture (B)

➤ Glue the sealing lips (see chapter “Accessories” on page 16) on the side of the

furniture (4).

➤ Push the refrigerator combination against the flexible sealing lips on furniture.

✔ The space behind the refrigerator is sealed to the interior of the vehicle.

Side gap distance of 5 mm to 10 mm (0.39 in.) between refrigerator and

furniture (C)

➤ Glue the double lipped sealing (see chapter “Accessories” on page 16) on the

side of the furniture (4).

➤ Push the refrigerator combination against the double lipped sealing on furniture.

✔ The space behind the refrigerator is sealed to the interior of the vehicle.

4.3 Making air inlet and outlet vents

I

➤ Make an air inlet vent and an air outlet vent in the outer wall with the size of

249 mm x 490 mm (9.8 in. x 19.29 in.).

When doing so, observe the information, see chapter “Preparing the installa-

tion” on page 17.

NOTE

• Deviations from the inlet and outlet variations shown here must be

approved by the manufacturer.

• At high ambient temperatures, the refrigerator can only provide its

maximum cooling capacity if the optimum ventilation has been pro-

vided.

DometicRMD10.5_INM_4445102585_AMER(en-fr)_202x-xx-xx.book Seite 19 Donnerstag, 28. Januar 2021 7:27 19

EN

Installing the refrigerator RMD10

20

If the ventilation grill of the air inlet vent cannot be installed flush with the floor of the

niche, install an inlet vent in the floor. Any leaking gas can thus flow downwards.

➤ Make an air inlet vent of at least Ø 40 mm (1.57 in.) in the floor (fig. 8 1, page 8)

behind the refrigerator near the gas burner.

➤ Shield the end of the opening with a deflector to prevent sludge or dirt from get-

ting inside while driving (fig. 8 2, page 8).

If you have to use a roof vent instead of the air outlet vent:

➤ Cut out a section in the roof. Refer to the roof vent instruction manual for the

required dimensions.

When doing so, observe the information in chapter “Preparing the installation”

on page 17.

4.4 Installing the ventilation grill

I

➤ Seal the installation frame to make the connection waterproof (fig. 0, page 9).

➤ Insert the installation frame and screw it down tightly (fig. a, page 9). Use all the

fixing holes for this.

➤ Insert the ventilation grill as shown (fig. b, page 9).

NOTE

Use exclusively original Dometic ventilation grills to ensure safe

operation.

No. in

fig. 9, page 8

Description

1Slider

2 Ventilation grill

3 Installation frame

4 Fastening for condensation drain

DometicRMD10.5_INM_4445102585_AMER(en-fr)_202x-xx-xx.book Seite 20 Donnerstag, 28. Januar 2021 7:27 19

La page charge ...

Dometic RMD10 Guide d'installation

Dometic RMD10 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents