Hitachi C 10FSHC Safety And Instruction Manual

DOUBLE INSULATION

DOUBLE ISOLATION

AISLAMIENTO DOBLE

Model

Modèle

Modelo

C 10FSHC

(Laser Marker Equipment)

(Outil avec marqueur à laser)

(Equipo marcador láser)

Slide Compound Miter Saw

Scie a coupe d’onglet radiale

Tronzadora radial abatible

SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL

WARNING

IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily injury!

This manual contains important information about product safety. Please read and understand

this manual before operating the power tool. Please keep this manual available for other users

and owners before they use the power tool. This manual should be stored in safe place.

INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI

AVERTISSEMENT

Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner la mort

ou de sérieuses blessures corporelles!

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce produit.

Prière de lire et de comprendre ce mode d’emploi AVANT d’utiliser l’outil motorisé. Garder ce

mode d’emploi à la disponibilité des autres utilisateurs et propriétaires avant qu’ils utilisent

l’outil motorisé. Ce mode d’emploi doit être conservé dans un endroit sûr.

INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES

ADVERTENCIA

¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede resultar

en lesiones de gravedad o la muerte!

Este manual contiene información importante sobre la seguridad del producto. Lea y

comprenda este manual ANTES de utilizar la herramienta eléctrica. Guarde este manual para

que puedan leerlo otras personas antes de utilizar la herramienta eléctrica. Este manual debe

ser guardado en un lugar seguro.

2

CONTENTS

TABLE DES MATIERES

ÍNDICE

English

Français

Español

Page

IMPORTANT SAFETY INFORMATION ...................3

MEANINGS OF SIGNAL WORDS ...........................3

SAFETY ......................................................................4

IMPORTANT SAFETY INSTRUCTIONS FOR

USING ALL POWER TOOLS ................................4

REPLACEMENT PARTS ..........................................8

USE PROPER EXTENSION CORD .........................8

DOUBLE INSULATION FOR SAFER OPERATION ....9

OPERATION AND MAINTENANCE ........................ 10

NAME OF PARTS...................................................10

SPECI FICATIO NS ..................................................12

ACCES S O RIES ...................................................... 13

APPLICATIONS ...................................................... 14

Page

INFORMATIONS IMPORTANTES DE

SÉCURITÉ ...........................................................42

SIGNIFICATION DES MOTS

D’AVERTISSEMENT ...........................................42

SECURITE ................................................................ 43

CONSIGNES DE SECURITE RELATIVES AUX

OUTILS ÉLECTRIQUES .....................................43

PIECES DE RECHANGE .......................................47

UTILISER LE CORDON DE RALLONGE

APPROPRIÉ ........................................................ 48

DOUBLE ISOLATION POUR UN

FONCTIONNEMENT PLUS SUR........................48

UTILISATION ET ENTRETIEN ................................50

NOM DES PIÈCES .................................................50

Página

INFORMACIÓN IMPORTANTE SOBRE

SEGURIDAD .......................................................84

SIGNIFICADO DE LAS PALABRAS DE

SEÑALIZACIÓN ..................................................84

SEGURIDAD .............................................................85

NORMAS DE SEGURIDAD PARA LAS

HERRAMIENTAS ELÉCTRICAS.........................85

PIEZAS DE REEMPLAZO......................................89

UTILICE EL CABLE PROLONGADOR

ADECUADO ........................................................90

AISLAMIENTO DOBLE PARA OFRECER UNA

OPERACIÓN MÁS SEGURA ..............................90

OPERACIÓN Y MANTENIMIENTO .........................9 2

NOMENCLATURA DE PARTES ............................92

ESPECIFICACIONES.............................................94

Page

PREPARATION BEFORE OPERATION ................14

BEFORE USING .................................................... 16

BEFORE CUTTING ................................................18

PRACTICAL APPLICATIONS ................................27

SAW BLADE MOUNTING AND DISMOUNTING ....37

MAINTENANCE AND INSPECTION .....................39

SERVICE AND REPAIRS ....................................... 41

PARTS LIST .......................................................... 126

Page

SPÉCI FICATIO NS .................................................. 52

ACCES S O I RES ......................................................5 3

APPLICATIONS ......................................................5 4

PRÉPARATION AVANT L’UTILISATION ................54

AVANT L’UTILISATION ..........................................56

AVANT LA COUPE .................................................58

APPLICATIONS PRATIQUES ................................68

INSTALLATION ET RETRAIT DE LA LAME ..........79

ENTRETIEN ET INSPECTION ...............................81

SERVICE APRÈS-VENTE ET RÉPARATIONS ......83

LISTE DES PIECES ..............................................126

Página

ACCESORIOS........................................................95

APLICACIONES .....................................................96

PREPARATIVOS PREVIOS A LA

OPERACIÓN ....................................................... 96

ANTES DE LA UTILIZACIÓN .................................98

ANTES DEL CORTE ............................................100

APLICACIONES PRÁCTICAS ............................. 110

MONTAJE Y DESMONTAJE DE LA

HOJA DE SIERRA .............................................120

MANTENIMIENTO E INSPECCIÓN .................... 123

SERVICIO Y REPARACIONES ............................125

LISTA DE PIEZAS .................................................126

3

English

IMPORTANT SAFETY INFORMATION

Read and understand all of the safety precautions, warnings and operating instructions in the

Instruction Manual before operating or maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused by the failure

to observe basic safety rules or precautions. An accident can often be avoided by recognizing a

potentially hazardous situation before it occurs, and by observing appropriate safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual and in

the sections which contain the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identiﬁ ed by

WARNINGS on the power tool and in this Instruction Manual.

NEVER use this power tool in a manner that has not been speciﬁ cally recommended by

HITACHI.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situations which, if ignored, could result in death

or serious injury.

CAUTION indicates a potentially hazardous situations which, if not avoided, may result in

minor or moderate injury, or may cause machine damage.

NOTE emphasizes essential information.

4

English

SAFETY

IMPORTANT SAFETY INSTRUCTIONS

FOR USING ALL POWER TOOLS

READ ALL OF THE WARNINGS AND OPERATING INSTRUCTIONS IN THIS

MANUAL BEFORE OPERATING OR MAINTAINING THIS TOOL:

WARNING: When using this electric tool, take all necessary precautions to minimize

the risk of electric shock or other personal injury.

In particular, always comply with the following safety rules:

1. ALWAYS KEEP GUARDS IN PLACE and in working order.

2. ALWAYS REMOVE ADJUSTING KEYS AND WRENCHES BEFORE STARTING TOOL.

Always conﬁ rm that all keys and adjusting wrenches have been removed from the tool

before it is turned on.

3. ALWAYS KEEP WORK AREA CLEAN. Avoid injuries by not cluttering the work areas and

work benches.

4. NEVER USE TOOL IN HAZARDOUS ENVIRONMENTS. Never use the power tool in damp

or wet places and never expose it to rain. Always keep the work area well lighted.

5. NEVER PERMIT CHILDREN OR OTHERS TO LOITER NEAR THE WORK AREA. Keep

all people (especially children) away from the work area. Always unplug unattended tools

and keep the work place tamper-proof by installing locks on the doors and on the master

switches. Always remove the lock- oﬀ button from the tool and store it in a secure place,

when the tool is not in use.

6. NEVER FORCE THE TOOL. It will do the job better and more safely if it is operated at the

rate for which it was designed.

7. ALWAYS USE THE RIGHT TOOLS. Never force a tool or an attachment to do a job for

which it was not designed.

8. ALWAYS WEAR PROPER APPAREL WHEN WORKING WITH THE TOOL. Never wear

loose clothing, gloves, neckties, rings, bracelets or other jewelry which may get caught in

the moving parts. Always wear non-slip footwear, preferably with steel toes. Wear protective

hair covering to contain long hair.

9. ALWAYS WEAR EYE PROTECTION WITH SIDE SHIELDS THAT MEETS THE

REQUIREMENTS OF ANSI STANDARD Z87.1 WHEN WORKING WITH THE TOOL TO

PREVENT EYE INJURY. Ordinary eyeglasses do not provide adequate protection because

they do not contain impact resistant safety glass. Also, use a face mask for additional safety

and wear a dust mask if the cutting operation produces dust.

10. ALWAYS SECURE THE WORKPIECE TO THE FENCE OR THE TABLE. Use clamps or a

vise to hold the workpiece in place. It is safer than using your hand and it frees both hands

to operate the tool.

5

English

11. NEVER OVERREACH. Always keep proper footing and balance when working with the

tool.

12. ALWAYS MAINTAIN TOOLS WITH CARE. Always keep tools sharp and clean for the best

and safest performance. Always follow instructions for lubricating the tool and for changing

accessories.

13. ALWAYS DISCONNECT THE TOOL before servicing and before changing blades or other

accessories.

14. NEVER RISK UNINTENTIONAL STARTING WHEN PLUGGING IN THE TOOL. Always

conﬁ rm that the switch is in the OFF position before inserting the power plug into the

receptacle.

15. ALWAYS USE RECOMMENDED ACCESSORIES ONLY WHEN OPERATING THIS TOOL.

Consult this instruction manual for descriptions of recommended accessories. To avoid

personal injuries, use only recommended accessories in conjunction with this tool.

16. NEVER STAND ON THE TOOL. Prevent serious injury by not tipping the tool and by not

risking unintentional contact with the saw blade.

17. ALWAYS CHECK FOR DAMAGED PARTS BEFORE USING THE TOOL. Always check

the guard and all other components for damage before using the tool to assure that they will

function properly. Check all moving parts for proper alignment, freedom from binding and

other conditions that might aﬀ ect proper operation. Always repair or replace any damaged

guards or other damaged components before using the tool.

18. ALWAYS CONFIRM THE ROTATION DIRECTION OF THE BLADE BEFORE USING THE

TOOL. Always feed work into the tool against the rotation direction of the blade in order to

prevent possible injury.

19. NEVER LEAVE THE TOOL RUNNING WHILE UNATTENDED. TURN POWER OFF. Do

not leave tool until it comes to a complete stop. Always turn the power oﬀ when the tool is

not in use. Always unplug the power cord when the tool is not in use.

20. This tool was not designed to be used for mass-production applications and should not be

used in mass-production environments.

21. When servicing this tool, use only authorized replacement parts.

22. Apply 120 volts AC only to this tool. Applying the wrong voltage or applying DC power

can cause the POWER TOOL to operate improperly and cause serious personal injury or

damage to the tool.

23. Never raise the saw blade from the workpiece until it has ﬁ rst come to a complete stop.

24. Always use outboard stands to provide support for long workpieces that overhang the table

of the slide compound miter saw.

25. Always return the carriage to the full rear position after each crosscut operation in order to

reduce the risk of injury.

26. POLARIZED PLUGS To reduce the risk of electric shock, this equipment has a polarized

plug (one blade is wider than the other). This plug will ﬁ t in a polarized outlet only one way.

If the plug does not ﬁ t fully in the outlet, reverse the plug. If it still does not ﬁ t, contact a

qualiﬁ ed electrician to install the proper outlet. Do not change the plug in any way.

Speciﬁ c Safety Rules for Use of this Power Tool

WARNING: The following speciﬁ c operating instructions must be observed when

using this POWER TOOL in order to avoid injury:

6

English

DO’s

ALWAYS OBSERVE THE FOLLOWING RULES TO ASSURE SAFE USE OF THIS TOOL:

1. Review this Manual and familiarize yourself with the safety rules and operating instructions

for this POWER TOOL before attempting to use it.

2. Remove all packing materials attached or connected to the tool before attempting to operate

it.

3. Always conﬁ rm that the POWER TOOL is clean before using it.

4. Always wear snug-ﬁ tting clothing, non-skid footwear (preferably with steel toes) and eye

protection when operating the POWER TOOL.

5. Always handle the POWER TOOL carefully. If the POWER TOOL falls or strikes against a

hard object, it might become deformed or cracked or sustain other damage.

6. Always cease operating the saw at once, if you notice any abnormality whatsoever.

7. Always conﬁ rm that all components are mounted properly and securely before using the

tool.

8. When replacing the saw blade, always conﬁ rm that the rpm rating of the new blade is correct

for use on this tool.

9. Always shut oﬀ the power and wait for the saw blade to completely stop rotating before

doing any maintenance or adjustments.

10. During slide cutting, always push the saw blade away from the operator.

11. Always clamp or otherwise secure the workpiece to the fence; otherwise the workpiece

might be thrust form the table and cause bodily harm.

12. During miter or bevel cutting, always wait for the rotation of the blade to stop completely

before lifting the saw blade.

13. Always make a trial run ﬁ rst before attempting any new use of the saw.

14. Always handle the saw blade with care when dismounting and mounting it.

15. Always conﬁ rm that the workpiece is free of nails or other foreign objects before beginning

a cut.

16. Always keep your hands out of the path of the saw blade.

17. Always conﬁ rm that the lower guard is in the proper place before using the saw.

18. Always conﬁ rm that the lower guard does not obstruct the sliding motion of the saw before

attempting slide cutting.

19. Inspect the tool power cords periodically.

20. Always conﬁ rm that the proper lengths and types of extension cords are being utilized, if

necessary, before starting the tool.

21. Always conﬁ rm that the motor air vents are fully open before using the tool.

22. Always wait until the motor has reached full speed before starting a cut.

23. Always keep the handles dry, clean and free of oil and grease. Hold the tool ﬁ rmly when in

use.

24. Always use outboard stands to provide support for long workpieces that overhang the table

of the slide compound miter saw.

25. Always operate the tool after ensuring the workpiece is ﬁ xed properly with a vise assembly.

26. The operating instructions provided with the tool shall direct the user to secure the tool to

supporting structure if, during normal operation, there is a tendency for the tool to tip over,

slide, or walk on the supporting surface.

7

English

DON’Ts

NEVER VIOLATE THE FOLLOWING RULES TO ASSURE SAFE USE OF THIS TOOL:

1. Never operate the POWER TOOL unless you fully understand the operating instructions

contained in this Manual.

2. Never leave the POWER TOOL unattended without ﬁ rst unplugging the power cord.

3. Never operate the POWER TOOL when you are tired, after you have taken any medications,

or have consumed any alcoholic beverages.

4. Never use the POWER TOOL for applications not speciﬁ ed in the instruction manual.

5. Never operate the tool while wearing loose clothing, a necktie or jewelry, or while your hair

is uncovered, to protect against getting caught in the moving machinery.

6. Never reach around the saw blade.

7. Never touch any moving parts, including the blade, while the saw is in use.

8. Never remove any safety devices or blade guards; use of the tool without them would be

hazardous.

9. Never lock the lower guard; always conﬁ rm that it slides smoothly before using the tool.

10. Never damage the power cord of the tool.

11. Never attempt to move a plugged-in POWER TOOL while your ﬁ nger is on the starting

switch.

12. Never use the POWER TOOL if the starting switch does not turn on and oﬀ properly.

13. Never use the POWER TOOL if the plastic housing or the handle is cracked or deformed.

14. Never use the POWER TOOL near ﬂ ammable liquids or gases because sparking can cause

an explosion.

15. Never clean plastic components with solvents because the plastic may dissolve.

16. Never operate the saw unless all the blade guards are in place.

17. Never raise the saw blade from the workpiece until it has ﬁ rst come to a complete stop.

18. When slide cutting, never pull the handle toward the operator, since this could cause the

saw blade to kick up from the workpiece. Always push the handle away from the operator in

a single, smooth motion.

19. Never place your limbs inside of the line next to warning sign “

” while the tool is being

operated. This may cause hazardous conditions.

20. Never use abrasive type blades on this saw.

21. Never expose to rain or use in damp locations.

22. Never cut ferrous metals or masonry.

WARNING

FOR YOUR OWN SAFETY READ THIS INSTRUCTION MANUAL BEFORE OPERATING

THE SLIDE COMPOUND MITER SAW

1. Always wear eye protection when using the slide compound miter saw.

2. Always keep hands out of the path of the saw blade.

3. Never operate the saw without the guards in place.

4. Never perform any freehand operation with the slide compound miter saw.

5. Never reach around the saw blade.

8

English

6. Always turn oﬀ tool and wait for saw blade to stop before moving workpiece or changing

settings.

7. Always disconnect power before changing blade or servicing.

8. Saw blade diameter is 10" (255 mm).

9. No load speed is 3,200/min.

10. To reduce the risk of injury, return carriage to the full rear position after each crosscut

operation.

REPLACEMENT PARTS

When servicing use only identical replacement parts.

Repairs should be conducted only by a Hitachi authorized service center.

USE PROPER EXTENSION CORD

Make sure your extension cord is in good condition. When using an extension cord, be sure to

use one heavy enough to carry the current your product will draw. An undersized cord will cause

a drop in line voltage resulting in loss of power and overheating. Table shows the correct size to

use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier

gage. The smaller the gage number, the heavier the cord.

MINIMUM GAGE FOR CORD SETS

Total Length of Cord in Feet (Meter)

0 – 25

(0 – 7.6)

26 – 50

(7.9 – 15.2)

51 – 100

(15.5 – 30.5)

101 – 150

(30.8 – 45.7)

Ampere Rating AWG

More

Than

Not More

Than

0 – 6 18 16 16 14

6 – 10 18 16 14 12

10 – 12 16 16 14 12

12 – 16 14 12 Not Recommended

WARNING: Avoid electrical shock hazard. Never use this tool with a damaged or

frayed electrical cord or extension cord.

Inspect all electrical cords regularly. Never use in or near water or in

any environment where electric shock is possible.

9

English

DOUBLE INSULATION FOR SAFER OPERATION

To ensure safer operation of this power tool, HITACHI has adopted a double insulation design.

“Double insulation” means that two physically separated insulation systems have been used to

insulate the electrically conductive materials connected to the power supply from the outer frame

handled by the operator. Therefore, either the symbol “

” or the words and “Double insulation”

appear on the power tool or on the nameplate.

Although this system has no external grounding, you must still follow the normal electrical

safety precautions given in this Instruction Manual, including not using the power tool in wet

environments.

To keep the double insulation system eﬀ ective, follow these precautions:

* Only HITACHI AUTHORIZED SERVICE CENTER should disassemble or assemble this power

tool, and only genuine HITACHI replacement parts should be installed.

* Clean the exterior of the power tool only with a soft cloth moistened with soapy water and dry

thoroughly.

* Never use solvents, gasoline or thinners on plastic components; otherwise the plastic may

dissolve.

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO

OTHER USERS

AND

OWNERS OF THIS TOOL!

10

English

OPERATION AND MAINTENANCE

NOTE: The information contained in this Instruction Manual is designed to assist you

in the safe operation and maintenance of the power tool. Some illustrations in

this Instruction Manual may show details or attachments that diﬀ er from those

on your own power tool.

NAME OF PARTS

MODEL C10FSHC

Sub fence (B)

Dust bag

Slide carriage

Holder (A)

Laser marker

Vise assembly

Fence (B)

Base

Gear case

Switch handle

Lower guard

Saw blade

Sub fence (A)

Fence (A)

Table insert

Turntable

Indicator

(For miter scale)

Rotation

direction

Indicator

(For bevel scale)

Motor head

Slide securing knob

Trigger switch

Positive stop

lock button

Miter lock handle

Bevel lock handle

Miter detent

override button

Support rod ass’y

Fig. 1

11

English

Mounting hold

Dust port

Saw blade

Trigger switch

Spindle lock

Set pin (A)

Hinge

Motor ass’y

Stop knob

Locking pin

Bracket (A)

Carriage handle

Laser marker switch

Table insert

LED light switch

Anchor plate

Support rod ass’y

Fig. 2

12

English

SPECIFICATIONS

Item Model C 10FSHC

Motor Type Series commutator motor

Power source Single-phase AC 60Hz

Voltage (Volts) 120

Full-load current (Amp) 15

Laser Marker Maximum output

<5mW CLASS

a Laser Product

Wave length 630 – 660 nm

Laser medium Laser Diode

Applicable saw

blade

Outside Dia. 10" (255 mm)

Hole Dia. 5/8" (15.9 mm)

No load speed 3,200/min

Max.

sawing

dimension

Head Turntable Max. sawing dimension

Miter 0 0 (With anchor plate)

Max. Height

Max. Width

(Without anchor plate)

Max. Height

Max. Width

3-1/2" (89 mm)

11-1/2" (292 mm)

2-1/2" (64 mm)

12-1/2" (318 mm)

0 Left 45°

or

Right 45°

(With anchor plate)

Max. Height

Max. Width

(Without anchor plate)

Max. Height

Max. Width

3-1/2" (89 mm)

8" (204 mm)

2-1/2" (64 mm)

8-3/4" (222 mm)

0 Left 55° (With anchor plate)

Max.Height

Max.Width

(Without anchor plate)

Max.Height

Max.Width

3-1/2" (89 mm)

6-7/8" (176 mm)

2-1/2" (64 mm)

7-1/4" (182 mm)

0 Right 60° (With anchor plate)

Max.Height

Max.Width

(Without anchor plate)

Max.Height

Max.Width

3-1/2" (89 mm)

5-3/4" (146 mm)

2-1/2" (64 mm)

6-1/4" (158 mm)

Bevel Left 45° 0 (With anchor plate)

Max. Height

Max. Width

(Without anchor plate)

Max. Height

Max. Width

1-3/4" (45 mm)

11-1/2" (292 mm)

1-5/8" (41 mm)

12-1/2" (318 mm)

Right 45° 0 (With anchor plate)

Max. Height

Max. Width

(Without anchor plate)

Max. Height

Max. Width

1" (25 mm)

11-1/2" (292 mm)

3/4" (19 mm)

12-1/2" (318 mm)

Compound Left 45° Left 45°

or

Right 45°

(With anchor plate)

Max. Height

Max. Width

(Without anchor plate)

Max. Height

Max. Width

1-3/4" (45 mm)

8" (204 mm)

1-

5/8" (41 mm)

8-3/4" (222 mm)

Right 45° Left 45°

or

Right 45°

(With anchor plate)

Max. Height

Max. Width

(Without anchor plate)

Max. Height

Max. Width

1" (25 mm)

8" (204 mm)

3/4" (19 mm)

8-3/4" (222 mm)

Miter sawing range Left 0° – 55° Right 0° – 60°

Bevel sawing range Left 0° – 48° Right 0° – 48°

Compound sawing range Left (Bevel) 0° – 45°, Left (Miter) 0° – 45°

Right (Bevel) 0° – 45°, Right (Miter) 0° – 45°

Net weight 45.6 lbs. (20.7 kg)

Cord 2 Conductor type cable 6ft. (1.8 m)

13

English

ACCESSORIES

WARNING: Accessories for this power tool are mentioned in this Instruction

Manual.

The use of any other attachment or accessory can be dangerous and

could cause injury or mechanical damage.

STANDARD ACCESSORIES

3 13 mm Wrench (1 piece)

1 Vise Assembly (1 piece)

For how to use, refer to page 28.

2 Dust bag (1 piece)

For how to use, refer to page 15.

4 Support rod ass’y (2 pieces)

5 mm screw (2 pieces)

Fig. 3

NOTE: Accessories are subject to change without any obligation on the part of the

HITACHI.

14

English

APPLICATIONS

Wood and aluminum sash.

PREPARATION BEFORE OPERATION

Make the following preparations before operating the power tool:

1. Remove all packing materials attached or connected to the tool before attempting to operate

it.

2. Installation

11-39/64"

(295 mm)

11/32" (9 mm)

4 holes

11-27/64"

(290 mm)

10-23/64"

(263 mm)

1" (25 mm) thick bench

Work bench 5/16" (8 mm) nut

5/16" (8mm) boltBase

Fig. 4

Attach the power tool to a level, horizontal work bench in accordance with Fig. 4.

Select 5/16" (8 mm) diameter bolts suitable in length for the thickness of the work bench.

Bolt length should be at least 1-9/16" (40 mm) plus the thickness of the work bench.

For example, use 2-9/16" (65 mm) or larger bolts for a 1" (25 mm) thick work bench.

The support rod ass’y attached to the rear of the base helps stabilize the power tool.

Installing the support rod ass’y

Insert one support rod ass’y into the hole located at the

rear of the base and push it in as far as it will go.

Thread the 5 mm screw into the hole next to the

mounting hold.

Firmly tighten the 5 mm screw with a screwdriver.

Repeat the above steps for installing the other support

rod ass’y.

Support

rod ass’y

5 mm

screw

Hole

Fig. 5

15

English

3. Releasing the locking pin

When the power tool is prepared for shipping, its

main parts are secured by a locking pin.

Press the handle slightly down and pull out the

locking pin to disengag the cutting head.

NOTE: Lowering the handle slightly will enable

you to disengage the locking pin more

easily and safely. The lock position

of the locking pin is for carrying and

storage only.

4. Installing the dust bag and vise

Install the dust bag onto the dust port on the miter

saw. Fit the connecting tube of dust bag and the dust

port together.

To empty the dust bag, pull out the dust bag assembly

from dust port. Open zipper on underside of bag and

empty into waste container. Check frequently and

empty the dust bag before it gets full.

NOTE: The dust bag should be angled toward

the right side of the saw for best results.

This will also avoid any interference

during the saw operation.

CAUTION: Empty the dust bag frequently to prevent the duct and the lower

guard from becoming clogged.

Sawdust will accumulate more quickly than normal during bevel

cutting.

WARNING: Do not use this saw to cut and/or sand metals. the hot chips or

sparks may ignite saw dust from the bag material.

(Attach the vise assembly as shown in Fig. 1, Fig. 2 and Fig. 25.)

Pull

Locking pin

Switch

Handle

Fig. 6

Dust port

Dust bag

Fig. 7

16

English

5. Power cord storage

Fig. 8-a Fig. 8-b

Bracket (A)

Bracket (B)

Bracket (A)

Bracket (B)

For convenience and to prevent damage to the power cord when the miter saw is not in use

or is in transportation, there are two brackets at the rear side of the slide carriage for winding

the cord. (Fig. 8-a)

NOTE: To rapidly release the power cord, turn the upper bracket (A) 180°. It will

release the cord. (Fig. 8-b)

BEFORE USING

1. Make sure the power source is appropriate for the tool.

WARNING: Never connect the power tool unless the available AC power

source is of the same voltage as that speciﬁ ed on the nameplate

of the tool.

Never connect this power tool to a DC power source.

2. Make sure the trigger switch is turned OFF.

WARNING: If the power cord is connected to the power source with the

trigger switch turned ON the power tool will start suddenly and

can cause a serious accident.

3. Check the saw blade for visible defects.

Conﬁ rm that the saw blade is free of cracks or other visible damage.

4. Conﬁ rm that the saw blade is attached securely to the power tool.

Using the supplied 13 mm wrench, tighten the 8 mm bolt on the saw blade spindle to secure

the saw blade.

For details, see Fig. 44- a, Fig. 44-b, Fig. 44-c and Fig. 44-d in the section on “SAW BLADE

MOUNTING AND DISMOUNTING”.

17

English

5. Check the lower guard for proper operation.

Lower guard is designed to protect the operator from

coming into contact with the saw blade during operation

of the tool.

Always check that the lower guard moves smoothly

and covers the saw blade properly.

WARNING: NEVER OPERATE THE POWER TOOL if the lower guard does not

function smoothly.

6. Conﬁ rm the position of the spindle lock before using the tool.

After installing the saw blade, conﬁ rm that the spindle lock has been returned to the released

position before using the power tool (see Fig. 2).

7. Check the Power Receptacle.

To prevent overheating, accidental stopping or intermittent operation, conﬁ rm that the

power cord plug ﬁ ts properly in the electrical receptacle and does not fall out after it is

inserted. Repair or replace the receptacle if it is faulty.

8. Conﬁ rm the tool’s power cord is not damaged.

Repair or replace the power cord if an inspection indicates that it is damaged

9. Eye protection

Always wear eye protection with side shields that meets the requirements of ANSI Standard

Z87.1. Ordinary eyeglasses do not provide adequate protection because they do not contain

impact resistant safety glass.

WARNING: Operating the tool without wearing proper eye protection may

result in serious injury.

10. Electric brake

This tool is equipped with an electric brake which will typically stop the blade within 5

seconds after the trigger switch is released.

Occasionally, there will be a delay in the brake engaging which will result in a longer blade

stopping time. On rare occasions, the brake may not engage at all and the saw blade will

coast to a stop.

If the brake fails to engage frequently, depress and release the trigger switch to turn the tool

on and oﬀ 4 or 5 times. If the brake still does not engage, have the tool serviced at a Hitachi

authorized service center.

Always conﬁ rm that the saw blade has completely stopped before raising it from the

workpiece.

The brake is not a substitute for a properly functioning lower guard. Check the function of

the lower guard before each use. Serious personal injury may occur if the lower guard does

not move smoothly and cover the blade properly.

Fig. 9

Lower guard

18

English

WARNING: Please be aware of the reaction of the Motor Head (Fig.1) when

the brake is activated. Braking causes the Motor Head to jerk

downward and the user should be prepared for this reaction,

especially when the trigger switch is released before the blade is

completely down. Failure to be familiar with, and prepared for, the

operational characteristics of the tool may cause serious injury.

AFTER CONNECTING THE POWER PLUG TO AN APPROPRIATE AC

POWER SOURCE, CHECK THE OPERATION OF THE TOOL AS FOLLOWS:

11. Trial Run

After conﬁ rming that no one is standing behind, the power tool start and conﬁ rm that no

operating abnormalities exist before attempting a cutting operation.

12. Inspect the rotating stability of the saw blade.

For precise cutting, rotate the saw blade and check for deﬂ ection to conﬁ rm that the blade

is not noticeably unstable; otherwise vibrations might occur and cause an accident.

BEFORE CUTTING

1. Positioning the table insert

Table insert

Saw blade

Table insert

Saw blade

4 mm

machine

screw

4 mm

machine

screw

[Right angle cutting]

Fig. 10-a

[Left bevel angle cutting]

Fig. 10-b

[Right bevel angle cutting]

Fig. 10-c

4 mm

machine

screw

Table inserts are installed on the turntable. When shipping the tool from the factory, the

table inserts are so ﬁ xed that the saw blade does not contact them. The burr of the bottom

surface of the workpiece is remarkably reduced, if the table insert is ﬁ xed so that the gap

between the side surface of the table insert and the saw blade will be minimum. Before

using the tool, eliminate this gap in accordance with the following procedure.

(1) Right angle cutting

Loosen the three 4 mm machine screws, then secure the left side table insert and

temporarily tighten the 4 mm machine screws of both ends. Then ﬁ x a workpiece

(about 7-7/8" (200 mm) wide) with the vise assembly and cut it oﬀ . After aligning the

cutting surface with the edge of the table insert, securely tighten the 4 mm machine

screws of both ends. Remove the workpiece and securely tighten the 4 mm center

machine screw. Adjust the right hand table insert in the same way.

19

English

(2) Left and right bevel angle cutting

Adjust the table insert in the manner shown in Fig. 10-b and Fig. 10-c following the

same procedure for right angle cutting.

CAUTION: After adjusting the table insert for right angle cutting, the table

insert will be cut to some extent if it is used for bevel angle cutting.

When bevel cutting operation is required, adjust the table insert

for bevel angle cutting.

2. Use of sub fence (A)

WARNING: The sub fence (A) must be extended when making any right angle

bevel cut. Failure to extend the sub fence (A) will not allow enough

space for the blade to pass through which could result in serious

injury. At extreme miter or bevel angles the saw blade may also

contact the fence.

This power tool is equipped with a sub fence (A).

In the case of direct angle cutting and left bevel angle cutting,

use the sub fence (A). Then, you can realize stable cutting of

the material with a wide back face.

When right angle cutting, loosen the lock knob, then slide the

sub fence (A) outward, as shown in Fig. 11.

When you slide sub fence (A) outward, if enough space

cannot be secured or the sub fence (A) comes into contact

with other parts of the tool including the motor, fully remove

sub fence (A) from fence (A). Also, make sure to remove the

lock knob from fence (A).

NOTE: When transporting the saw, always secure the sub fence (A) in the

collapsed position and lock it.

3. Use of sub fence (B)

WARNING: The sub fence (B) must be extended when making any left angle

bevel cut. Failure to extend the sub fence (B) will not allow enough

space for the blade to pass through which could result in serious

injury. At extreme miter or bevel angles the saw blade may also

contact the fence.

This power tool is equipped with a sub fence (B). In the case of

direct angle cutting and right bevel angle cutting, use the sub

fence (B). Then, you can realize stable cutting of the material

with a wide back face. When left angle cutting, loosen the lock

knob, then slide the sub fence (B) outward, as shown in Fig. 12.

When you slide sub fence (B) outward, if enough space cannot

be secured or the sub fence (B) comes into contact with other

parts of the tool including the lower guard, fully remove sub

fence (B) from fence (B).

Fig. 11

Fence (A)

Lock knob

Sub fence (A)

Lock knob

Fence (B)

Fig. 12

Sub fence (B)

20

English

NOTE: When transporting the saw, always secure the sub fence (B) in the

collapsed position and lock it.

4. Securing the workpiece

WARNING: Always clamp or vise to secure the workpiece to the fence;

otherwise the workpiece might be thrust from the table and cause

bodily harm.

5. Slide carriage system

WARNING: To reduce the risk of injury, return slide carriage to the full rear

position after each crosscut operation.

For chop cutting operations on small workpieces, slide the cutting

head assembly completely toward the rear of the unit and tighten

the slide securing knob.

To cut wide boards up to 305 mm, the slide securing knob must

be loosened to allow the cutting head slide freely.

6. Quick-cam locking lever operation

If miter angles required are NOT one of the

nine positive stops, the miter table can be

locked at any angle between these positive

stops by using the postive stop lock button

and miter lock handle.

Unlock the miter table by lifting up the miter

lock handle, grasp the miter lock handle and

pressing down on the postive stop lock button

to move the table to the desired angle, then

release the postive stop lock button. Press

down on the miter lock handle to lock the table

in position.

Slide securing knob

Fig. 13

Postive stop

lock button

Miter detent

override button

Bevel lock handle

Miter lock handle

Fig. 14

La page est en cours de chargement...

Hitachi C 10FSHC Safety And Instruction Manual

Hitachi C 10FSHC Safety And Instruction Manual

dans d''autres langues

Documents connexes

Autres documents