Indesit AQM9F 29 U (KW) Mode d'emploi

Marque: Indesit

Modèle: AQM9F 29 U (KW)

Catégorie: Machines à laver

Taper: Mode d'emploi

English,1

Contents

Installation, 2-3-4-5

Unpacking and levelling

Connecting the electricity and water supplies

Technical data

Description of the machine, 6-7

Control panel

How to run a wash cycle or a drying

cycle, 8

Wash cycles and options, 9

Table of wash cycles

Wash options

Detergents and laundry, 10

Detergent

Preparing the laundry

Washing recommendations

Load balancing system

Precautions and advice, 11

General safety

Disposal

Opening the porthole door manually

Care and maintenance, 12

Cutting off the water and electricity supplies

Cleaning the machine

Cleaning the detergent dispenser drawer

Caring for your appliance drum

Cleaning the pump

Checking the water inlet hose

Trouble shooting, 13

Assistance, 14

WASHER-DRYER

AQUALTIS

AQM9F 29 U

Instructions for

installation and use

, 29

 This symbol reminds you to read this instruction manual.

Français,15

Installation

 This instruction manual should be kept in a safe place

for future reference. If the washer-dryer is sold, given

away or moved, please ensure the manual is kept with

the machine, so that the new owner may benefit from

the advice contained within it.

 Read these instructions carefully: they contain vital

information relating to the safe installation and operation

of the appliance.

 Inside the pack containing this manual, you will also

find the guarantee and all the details necessary for

installation.

Unpacking and levelling

Unpacking

1. Once you have removed all the packaging from the

washer-dryer, make sure it has not been damaged

during transportation.

If it has been damaged, contact the retailer and do not

proceed any further with the installation process.

2. Remove the 4

protective screws (used

during transportation) and

the corresponding spacer,

located on the rear part of

the appliance (see figure).

3. Close off the holes using the plastic plugs supplied in

the pack.

4. Keep all the parts in a safe place; they will be needed

again if the washer-dryer is moved to another location,

to prevent the inside of the appliance being damaged.

 Packaging materials should not be used as toys for

children.

Levelling

1. Place the washer-dryer on a flat sturdy floor, without

resting it up against walls or cabinets.

2. If the floor is uneven,

the front feet of the

machine may be adjusted

until it reaches a horizontal

position (the angle of

inclination must not

exceed 2 degrees).

 If the appliance is levelled correctly, it will be more

stable and much less likely to cause vibrations and noise

while it is operating, particularly during the spin cycle.

 If it is placed on carpet or a rug, adjust the feet in such

a way as to allow a sufficient ventilation space

underneath the washer-dryer.

Connecting the electricity and water

supplies

Connecting the water inlet hose

 Before connecting the inlet hose to the water supply,

run the water until it is perfectly clear.

1. Connect the inlet hose

to the machine by

screwing it onto the cold

water inlet of the

appliance, which is

situated on the top right-

hand side of the rear part

of the appliance (see

figure).

2. Connect the inlet hose

by screwing it to a cold

water tab using a 3/4 gas

threaded connection (see

figure).

3. Make sure that the hose is not folded over or bent.

 The water pressure at the tap must fall within the

values indicated in the Technical data table (see next

page).

 If the inlet hose is not long enough, contact a

specialised shop or an authorised technician.

 Never use second-hand or old inlet hoses; use the

products supplied with the machine.

Connecting the drain hose

Connect the drain hose,

without bending it, to a

draining duct or a wall

drain situated between 65

and 100 cm from the floor;

alternatively, place it over

the edge of a basin, sink

or tub, fastening the duct

supplied to the tap (see

figure). The free end of

the hose should not be

underwater.

 We advise against the use of hose extensions; in case

of absolute need, the extension must have the same

diameter as the original hose and must not exceed 150

cm in length.

Electric connection

Before plugging the appliance into the mains socket,

make sure that:

 the socket is earthed and in compliance with the

applicable law;

 the socket is able to sustain the appliance's

maximum power load indicated in the Technical

details table (see page 5);

 the supply voltage is included within the values i

ndicated on the Technical details table

(see page 5);

 the socket is compatible with the washing

machine's plug. If this is not the case, replace

the socket or the plug.

Your appliance is now supplied with a 13 amp fused plug

it can be plugged into a 13 amp socket for immediate

use. Before using the appliance please read the

instructions below.

WARNING - THIS APPLIANCE MUST BE EARTHED.

THE FOLLOWING OPERATIONS SHOULD BE

CARRIED OUT BY A QUALIFIED ELECTRICIAN.

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA approved

fuse to BS 1362 should always be used, and the fuse

cover re-fitted. If the fuse cover is lost, the plug must

not be used until a replacement is obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be of the

correct colour as indicated by the coloured marking or

the colour that is embossed in words on the base of the

plug. Replacements can be obtained directly from your

nearest Service Depot.

Removing the plug:

If your appliance has a non-rewireable moulded plug

and you should wish to re-route the mains cable

through partitions, units etc., please ensure that either:

the plug is replaced by a fused 13 ampere re-wearable

plug bearing the BSI mark of approval.

or:

the mains cable is wired directly into a 13 amp cable

outlet, controlled by a switch, (in compliance with BS

5733) which is accessible without moving the appliance.

Disposing of the plug:

Ensure that before disposing of the plug itself, you make

the pins unusable so that it cannot be accidentally

inserted into a socket.

Instructions for connecting cable to an alternative plug:

Important: the wires in the mains lead are coloured in

accordance with the following code:

Green & Yellow Earth

Blue Neutral

Brown Live

As the colours of the wires in the lead may not

correspond with the coloured markings identifyng the

terminals in your plug, proceed as follows:

Connect Green & Yellow wire to terminal marked E or

or coloured Green or Green & Yellow.

Connect Brown wire to terminal marked L or coloured

Red.

Connect Blue wire to terminal marked N or coloured

Black.

65 - 100 cm

If a 13 amp plug (BS 1363) is used it must be fitted with

13 amp fuse, either in the plug or adaptor or at the

distribution board.

If you are in any doubt the electrical supply to your

machine, consult a qualified electrician before use.

How to connect an alternative plug:

The wires in this mains lead are coloured in accordance

with the following code:

BLUE NEUTRAL (N)

BROWN LIVE (L)

GREEN & YELLOW EARTH (E)

Disposing of the appliance:

When disposing of the appliance please remove the plug

by cutting the mains cable as close as possible to the

plug body and dispose of it as described above.

 The washing machine should not be installed in an

outdoor environment, not even when the area is

sheltered, because it may be very dangerous to leave it

exposed to rain and thunderstorms.

 When the washing machine is installed, the mains

socket must be within easy reach.

 Do not use extensions or multiple sockets.

 The power supply cable must never be bent or

dangerously compressed.

 The power supply cable must only be replaced by an

authorised serviceman.

Warning! The company denies all liability if and when

these norms are not respected.

GREEN &

YELLOW

BROWN

BLUE

13 ampere fuse

CROSS-BAR

CORD GRIP

Technical data

Model

AQM9F 29 U

Dimensions

width 59,5 cm

height 85 cm

depth 64,5 cm

Capacity

from 1to 9 kg for wash programme

from 1 to 6 kg for the drying programme

Electrical

connections

please refer to the technical data

plate fixed to the machine

Water connections

maximum pressure 1 MPa (10 bar)

minimum pressure 0.05 MPa (0.5 bar)

drum capacity 62 litres

Spin speed

up to 1200 rotations per minute

Energy rated

programmes

according to

regulation

EN 50229

Wash: programme ; temperature

60°C; using a load of 9 kg.

Drying: first drying cycle performed

with a 3 kg load, by selecting the

drying level "L1";

Second drying cycle performed with a

6 kg load, selecting the maximum

drying level "L4".

This appliance conforms to the

following EC Directives:

- 89/336/EEC dated 03/05/89

(Electromagnetic Compatibility) and

subsequent modifications

- 2006/95/EC (Low Voltage)

- 2002/96/EC

CONTROL

PANEL

PORTHOLE DOOR

HANDLE

KICK STRIP

ADJUSTABLE FEET

Description of the machine

PORTHOLE DOOR

Always use the handle to

open the porthole door (see

figure).

DETERGENT DISPENSER DRAWER

The detergent dispenser

drawer is located inside the

machine and can be

accessed by opening the

door.

For more information on

detergent measures, please

refer to the chapter entitled

Detergents and laundry.

Note: stick the label showing

the wash cycle descriptions and options on the front of

the detergent dispenser drawer. You will find the sticker

in the pack containing this manual.

1. pre-wash compartment:

use powder detergent.

 Before pouring in the

detergent, make sure that

extra compartment 3 has

been removed.

2. main wash compartment:

use powder or liquid

detergent. If using the latter

type of detergent, we

recommend it is poured into

the drawer immediately before you start the washer-

dryer.

3. extra compartment: Bleach

 The use of extra compartment 3 excludes the pre-

wash function.

washing additives compartment: for fabric softener or

liquid additives. We recommend that the maximum level

indicated by the grille is not exceeded, and that

concentrated fabric softeners are diluted.

Standby mode

This washer-dryer, in compliance with new energy saving

regulations, is fitted with an automatic standby system

which is enabled after about 30 minutes if no activity is

detected. Press the ON-OFF

button briefly and wait

for the machine to start up again.

TEMPERATURE button

WASH CYCLE

SELECTOR knob

OPTION buttons with

indicator lights

DOOR LOCKED

indicator light

START/PAUSE

button with indicator

light

WASH

CYCLE

PHASE

icons

DRYING

button

DELAYED

START

button

CONTROL PANEL

LOCK button with

indicator light

Button withON/OFF

indicator light

ECO indicator light

OPTION buttons with

indicator lights

TEMPERATURE

display

DRYING

display

DELAYED START/CYCLE

DURATIONdisplay

Control panel

Button with  ON/OFF indicator light: press this briefly

to switch the machine on or off. The green indicator light

indicates that the machine is switched on. To switch off

the washer-dryer during the wash cycle, press and hold

the button for approximately 3 seconds; if the button is

pressed briefly or accidentally the machine will not

switch off. If the machine is switched off during a wash

cycle, this wash cycle will be cancelled.

WASH CYCLE SELECTOR knob: may be turned in

either direction. To select the most suitable wash cycle,

please refer to the Table of wash cycles.

The knob will not move during the wash cycle.

TEMPERATURE

button: press to modify or exclude

the temperature setting; the value selected will appear

on the display above (see "How to run a wash cycle or a

drying cycle").

DRYING button

: press to decrease or exclude drying;

the selected drying level or time will appear on the display

(see "How to run a wash cycle or a drying cycle").

DELAYED START

button: press to set a delayed

start for the selected wash cycle; the set delay time will

appear on the display above (see "How to run a wash

cycle or a drying cycle").

OPTION buttons with indicator lights: press to select the

available options. The indicator light corresponding to the

selected option will remain lit (see "How to run a wash

cycle or a drying cycle").

WASH CYCLE PHASE icons: these illuminate to

indicate the progress of the wash cycle (Wash



Rinse

 Spin/Drain  Drying ). The text

lights up when the cycle is complete.

START/PAUSE button with indicator light: when the

green indicator light flashes slowly, press the button to

start a wash cycle. Once the cycle has begun the

indicator light will remain lit in a fixed manner. To pause

the wash cycle, press the button again; the indicator

light will flash in an orange colour. If the Door locked

indicator light is switched off, the door may be

opened. To start the wash cycle from the point at which

it was interrupted, press the button again.

DOOR LOCKED

indicator light: indicates that the

porthole door is locked. To open the door, pause the

wash cycle (see "How to run a wash cycle or a drying

cycle").

CONTROL PANEL LOCK

button with indicator

light: to activate or deactivate the control panel lock,

press and hold the button for approximately 2 seconds.

when the indicator light is illuminated, the control panel is

locked. This means it is possible to prevent wash cycles

from being modified accidentally, especially where there

are children in the home.

ECO indicator light: the

icon lights up when, after

altering the washing parameters, an energy saving of at

least 10% is made. Furthermore, before the machine

enters Standby mode, the icon will light up for a few

seconds; when the machine is switched off the

estimated energy saving will be around the 80% mark.

WARNING: before you use the washer-dryer for the first

time, run a wash cycle with detergent and no laundry,

using the 90° cottons cycle without pre-wash.

1. SWITCH THE MACHINE ON. Press the

button.

All the indicator lights will illuminate for 1 second; the

indicator light corresponding to the

button will then

remain lit in a fixed manner and the START/PAUSE

indicator light will flash slowly.

2. LOAD THE LAUNDRY. Open the porthole door.

Load the laundry, making sure you do not exceed the

maximum load value indicated in the table of wash

cycles on the following page.

3. MEASURE OUT THE DETERGENT. Pull out the

detergent dispenser drawer and pour the detergent

into the relevant compartments as described in

Description of the machine.

4. CLOSE THE PORTHOLE DOOR.

5. SELECT THE PROGRAMME. Turn the WASH CYCLE

SELECTOR KNOB right or left, until you have selected

the desired wash cycle. A temperature and spin speed is

set for each wash cycle; these may be adjusted.

6. CUSTOMISE THE WASH CYCLE. Use the

relevant buttons on the control panel:

Modify the temperature.

The machine automatically displays the maximum

temperature values set for the selected cycle, or the

most recently-used settings if they are compatible

with the selected cycle. The temperature can be

decreased by pressing the

button, until the cold

wash (

) setting is reached. If these buttons are

pressed again, the maximum values are restored.

 Exception: if the Cottons programme is selected, the

temperature can be increased up to a value of 90°C.

Setting the drying cycle

The first time the button

is pressed, the machine

will automatically select the maximum drying cycle

which is compatible with the selected wash cycle.

Subsequent presses will decrease the drying level and

then the drying time, until the cycle is excluded

completely (

). If these buttons are pressed again,

the maximum values are restored.

Drying may be set as follows:

A - Based on a set time period: between 20 and 180

minutes.

B- Based on the desired laundry dryness level:

Iron (L1): suitable for clothes which will need ironing

afterwards. the remaining dampness softens creases,

making them easier to remove.

Hanger (L2): ideal for clothes which do not need to be

dried fully.

Cupboard (L3): suitable for laundry which can be put

back in a cupboard without being ironed.

Extra (L4): suitable for garments which need to be

dried completely, such as sponges and bathrobes.

If your laundry load to be washed and dried is much

greater than the maximum stated load (see adjacent

table), perform the wash cycle, and when the cycle is

complete, divide the garments into groups and put

some of them back in the drum. At this point, follow

the instructions provided for a "Drying only" cycle.

Repeat this procedure for the remainder of the load. A

cooling-down period is always added to the end of

each drying cycle.

Drying only

Use the cycle selector knob to select a drying cycle

(

- - ) in accordance with the type of fabric. The

desired drying level or time may also be set using the

DRYING button

Set a delayed start.

Press the button until you have reached the desired

delay time. During the setting process, the delay time

is shown on the display and the

symbol flashes.

After selecting a delayed start time, the fixed

symbol and the cycle duration will appear on the

display. Press the button once to display the selected

delay time. To remove the delayed start option, press

the button until the display shows the text OFF; the

symbol will disappear.

 Once the START/PAUSE button has been pressed,

the time delay may only be decreased.

Modify the cycle settings.

Press the OPTION buttons to customise the wash

cycle in accordance with your own requirements.

 Press the button to activate the option; the

corresponding indicator light will switch on.

 Press the button again to disable the option; the

indicator light will switch off.

 If the selected option is not compatible with the

selected wash cycle, this incompatibility will be

signalled by the flashing of the indicator light and a

sound alert (3 beeps); the option will not be activated.

 If the selected option is not compatible with another

option that has been selected previously, the indicator

light corresponding to the first option selected will flash

and only the second option will be activated; the

indicator light corresponding to the button will remain

lit in a constant manner.

7. START THE PROGRAMME. Press the START/

PAUSE button. The corresponding indicator light

remains lit in a fixed manner and the porthole door

locks (the

DOOR LOCKED indicator light

illuminates). The icons corresponding to the wash

cycle phases will light up during the cycle to indicate

which phase is currently in progress.

To change a wash cycle once it has already started,

pause the washer-dryer by pressing the START/

PAUSE button; then select the desired cycle and

press the START/PAUSE button again. To open the

door during a wash cycle, press the START/PAUSE

button; if the DOOR LOCKED

indicator light is

switched off you may open the door. Press the

START/PAUSE button again to restart the wash cycle

from the point at which it was interrupted.

8. THE END OF THE WASH CYCLE. This is indicated

by the illuminated text END. The porthole door may be

opened immediately. If the START/PAUSE indicator light

is flashing, press the button to end the cycle. Open the

door, unload the laundry and switch off the machine.

 If you wish to cancel a cycle which has already begun,

press and hold the

button until the cycle stops and

the machine switches off.

How to run a wash cycle or a

drying cycle

Wash cycles and options

(*) The duration of the wash cycles can be checked

on the display.

(*) Note: 10 minutes after the START, the machine will recalculate the time remaining until the end of the wash cycle on the basis of the load inside it; this

value will then be shown on the display.

Table of wash cycles

For all Test Institutes:

1) Test wash cycle in compliance with regulation EN 50229: set wash cycle

with a temperature of 60°C.

2) Long wash cycle for cottons: set wash cycle

with a temperature of 40°C.

3) Short wash cycle for cottons: set wash cycle

with a temperature of 40°C.

Icon Description of the wash cycle

Max.

temp.

(°C)

Max.

speed

(rpm)

Drying

Detergent and additives

Max.

load

(kg)

Cycle

duration

Wash

Fabric

softener

Bleach

Cottons wash cycles

Cottons

with pre-wash

(Add detergent to the relevant compartment).

90° 1200

ll l

- 9

Cottons (1):

heavily soiled whites and resistant colours.

60°

(Max. 90°)

1200

ll l l

Cottons (2):

heavily soiled whites and delicate colours.

40° 1200

ll l l

Coloured

Cottons (3)

40° 1200

ll l l

Jeans

40° 800

ll l

- 4

Special cycles

Baby:

heavily soiled delicate colours

40° 800

ll l l

Mix 30':

to refresh lightly soiled garments quickly (not suitable

for wool, silk and clothes which require washing by hand)

30° 800

ll l

- 3,5

Durable

Synthetics

60° 800

ll l l

Silk:

for garments in silk and viscose, lingerie.

30° 0 -

- 2

Wool:

for wool, cashmere, etc.

40° 800

ll l

- 2

Drying cycles

Wash&Dry 30° 1200

ll l

- 1

Drying Cotton - -

- - - 6

Drying Synthetic - -

- - - 4

Drying Wool - -

- - - 1,5

Partials wash cycles

Rinse - 1200

Spin - 1200

- - - 9

Drain - 0 - - - - 9

Wash options

Super Wash

This option offers a high-performance wash due to the

greater quantity of water used in the initial phase of the

cycle, and due to the increased wash cycle duration, is

particularly useful for the

removal of stubborn stains.

It can be used with or

without bleach. If you desire

bleaching, insert the extra

tray compartment (3) into

compartment 1. When

pouring in the bleach, be

careful not to exceed the

max level marked on the

central pivot (see figure).

To bleach laundry without

carrying out a full wash cycle, pour the bleach into the

extra compartment 3, select the "Rinse" cycle

and

activate the "Super Wash" option

 It cannot be used in conjunction with

, , , , ,

, , , , , .

Easy Iron

By selecting this option, the wash and spin cycles will be

modified in order to reduce the formation of creases.

At the end of the cycle the washer-dryer drum

will rotate slowly; the Easy Iron and START/PAUSE

indicator lights will flash. To end the cycle press the

START/PAUSE button or the Easy Iron button.

For the Silk

wash cycle, the machine will end the

cycle while the laundry is soaking and the Easy

Iron indicator light will flash. To drain the water so that

the laundry may be removed, press the START/PAUSE

button or the Easy Iron button.

 It cannot be used in conjunction with

, , , , ,

, , , .

Note: If you also want to run the drying cycle, this option is

enabled only if combined with level Iron (L1).

Time Saver

If you select this option, the wash cycle duration will be

reduced by 30%-50%, depending on the selected cycle,

thereby guaranteeing simultaneous water and energy

saving. Use this cycle for lightly soiled garments.

 It cannot be used in conjunction with

, , , , ,

, , , , , .

Extra rinse

By selecting this option, the efficiency of the rinse is

increased and optimal residual detergent removal is

guaranteed. It is particularly useful for skin which is

sensitive to detergents. We recommend this option is

used with a full load of washing, or when a large amount

of detergent is required.

 It cannot be used in conjunction with

, , , , ,

, .

Detergents and laundry

Detergent

The type and quantity of detergent required depend on

the type of fabric you are washing (cotton, wool, silk,

etc.), as well as its colour, the washing temperature, the

level of soiling and the hardness of the water in the area.

Measuring out the detergent carefully will avoid wastage

and help to protect the environment: although they are

biodegradable, detergents still contain ingredients which

alter the balance of nature.

We recommend the following:

 use powder detergents for white cotton garments and

pre-washing.

 use liquid detergents for delicate cotton garments and

for all low-temperature wash cycles.

 use gentle liquid detergents for wool and silk

garments.

The detergent should be poured into the relevant

compartment - or the dispenser placed directly inside

the drum - before the wash cycle begins. In the latter

case, it will not be possible to select the Cottons with

pre-wash cycle.

 Do not use hand washing detergents because these

create too much foam.

Preparing the laundry

 Shake out the garments before loading them into the

machine.

 Divide the laundry according fabric type (symbol on the

washing instruction label) and colour, making sure you

separate the coloured garments from the white ones;

 Empty all pockets and check the buttons;

 Do not exceed the values listed in the Table of wash

cycles, which refer to the weight of the laundry when dry.

How much does your laundry weigh?

1 sheet 400-500 g

1 pillowcase 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1200 g

1 towel 150-250 g

1 pair of jeans 400-500 g

1 shirt 150-200 g

Washing recommendations

Jeans: use the special Jeans wash cycle for all

denim garments; turn inside out before washing and use

a liquid detergent.

Baby: use the special Baby

wash cycle to remove

the remove the soiling typically caused by babies, while

removing all traces of detergent from nappies in order to

prevent the delicate skin of babies from suffering allergic

reactions. The cycle has been designed to reduce the

amount of bacteria by using a greater quantity of water

and optimising the effect of special disinfecting additives

added to the detergent. At the end of the wash cycle,

the machine will slowly rotate the drum; to end the cycle

press the START/PAUSE button.

Silk: use the special Silk

wash cycle to wash all silk

garments. We recommend the use of special detergent

which has been designed to wash delicate clothes.

Curtains: use the Silk

wash cycle. Fold curtains

and place them in a pillow case or mesh bag.

Wool: Ariston is the only washer-dryer brand to have

been awarded the prestigious Woolmark Platinum Care

endorsement (M.0508) by the Woolmark Company,

which means that all woollen garments may be washed

in the washer-dryer, even those which state hand wash

only

on the label. The Wool wash cycle can be

used to wash all woollen garments in the washer-dryer

while guaranteeing optimum performance.

Bedlinen and towels: use the Bed & Bath

cycle

to wash laundry from all over the house; this optimises

fabric softener performance and helps you save time and

energy. We recommend the use of powder detergent.

Stubborn stains: it is wise to treat stubborn stains with

solid soap before washing, and to use the Cottons with

pre-wash cycle.

Wash & Dry

was designed to wash and dry lightly

soiled garments quickly. This cycle may be used to wash

and dry a laundry load of up to 1 kg in just 60 minutes.

To achieve optimum results, use liquid detergent and pre-

treat cuffs, collars and stains.

Load balancing system

Before every spin cycle, to avoid excessive vibrations

before every spin and to distribute the load in a uniform

manner, the drum rotates continuously at a speed which

is slightly greater than the washing rotation speed. If,

after several attempts, the load is not balanced

correctly, the machine spins at a reduced spin speed. If

the load is excessively unbalanced, the washer-dryer

performs the distribution process instead of spinning. To

encourage improved load distribution and balance, we

recommend small and large garments are mixed in the

load.

Precautions and tips

 The machine was designed and constructed in

accordance with international safety regulations. The

following information is provided for safety reasons and

must therefore be read carefully.

General safety

 This appliance is not intended for use by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience and

knowledge, unless they have been given supervision

or instruction concerning use of the appliance by a

person responsible for their safety.

Children should be supervised to ensure that they do

not play with the appliance.

 Do not dry unwashed items in the tumble dryer.

 Items that have been soiled with substances such

as cooking oil, acetone, alcohol, petrol, kerosene,

spot removers, turpentine, waxes and wax removers

should be washed in hot water with an extra amount

of detergent before being dried in the tumble dryer.

 Items such as foam rubber (latex foam), shower

caps, waterproof textiles, rubber backed articles and

clothes or pillows fitted with foam rubber pads should

not be dried in the tumble dryer.

 Fabric softeners, or similar products, should be used

as specified by the fabric softener instructions.

 The final part of a tumble dryer cycle occurs without

heat (cool down cycle) to ensure that the items are

left at a temperature that ensures that the items will

not be damaged.

WARNING: Never stop a tumble dryer before the end

of the drying cycle unless all items are quickly

removed and spread out so that the heat is

dissipated.

 This appliance was designed for domestic use only.

 Do not touch the machine when barefoot or with wet

or damp hands or feet.

 Do not pull on the power supply cable when

unplugging the appliance from the electricity socket.

Hold the plug and pull.

 Do not touch the drained water as it may reach

extremely high temperatures.

 Never force the porthole door. This could damage the

safety lock mechanism designed to prevent

accidental opening.

 If the appliance breaks down, do not under any

circumstances access the internal mechanisms in an

attempt to repair it yourself.

 Always keep children well away from the appliance

while it is operating.

 If it must be moved, proceed with the help of two or

three people and handle it with the utmost care.

Never try to do this alone, because the appliance is

very heavy.

 Before loading laundry into the washer dryer, make

sure the drum is empty.

 During the drying phase, the door tends to get

quite hot.

 Do not use the appliance to dry clothes that have

been washed with flammable solvents (e.g.

trichlorethylene).

 Do not use the appliance to dry foam rubber or

similar elastomers.

 Make sure that the water tap is turned on during

the drying cycles.

Disposal

 Disposing of the packaging materials: observe local

regulations so that the packaging may be re-used.

 The European Directive 2002/96/EC relating to Waste

Electrical and Electronic Equipment (WEEE) states

that household appliances should not be disposed of

using the normal solid urban waste cycle. Exhausted

appliances should be collected separately in order to

optimise the cost of re-using and recycling the

materials inside the machine, while preventing

potential damage to the atmosphere and to public

health. The crossed-out dustbin is marked on all

products to remind the owner of their obligations

regarding separated waste collection.

For more information relating to the correct disposal of

household appliances, owners should contact their

local authorities or appliance dealer.

Opening the porthole door manually

In the event that it is not possible to open the porthole

door due to a powercut, and if you wish to remove the

laundry, proceed as follows:

1. remove the plug from the

electrical socket.

2. make sure the water level

inside the machine is lower

than the door opening; if it is

not, remove excess water

using the drain hose,

collecting it in a bucket as

indicated in the figure.

3. remove the cover panel

on the lower front part of the

washer dryer (see overleaf).

4. pull outwards using the

tab as indicated in the figure,

until the plastic tie-rod is

freed from its stop position;

pull downwards until you

hear a click, which

indicates that the door is

now unlocked.

5. open the door; if this is

still not possible repeat the

procedure.

6. reposition the panel,

making sure the hooks are

securely in place before you

push it onto the appliance.

Cutting off the water and electricity

supplies

 Turn off the water tap after every wash cycle. This will

limit wear on the hydraulic system in the machine and

help to prevent leaks.

 Unplug the appliance when cleaning it and during all

maintenance work.

Cleaning the machine

The outer parts and rubber components of the appliance

can be cleaned using a soft cloth soaked in lukewarm

soapy water. Do not use solvents or abrasives.

Cleaning the detergent dispenser

drawer

To remove the drawer, press

lever (1) and pull the drawer

outwards (2) (see figure).

Wash it under running

water; this procedure should

be repeated frequently.

Caring for your appliance drum

 Always leave the door ajar to prevent unpleasant

odours from forming.

Cleaning the pump

The washer-dryer is fitted with a self-cleaning pump

which does not require any maintenance. Sometimes,

small items (such as coins or buttons) may fall into the

protective pre-chamber at the base of the pump.

 Make sure the wash cycle has finished and unplug the

appliance.

To access the pre-chamber:

1. take off the cover panel on the front of the machine

by first pressing it in the centre and then pushing

downwards on both sides until you can remove it (see

figures);

2. position a container so

that it will collect the water

which flows out

(approximately 1.5 l) (see

figure);

3. unscrew the lid by

rotating it in an anti-

clockwise direction (see

figure);

4. clean the inside thoroughly;

5. screw the lid back on;

6. reposition the panel, making sure the hooks are

securely in place before you push it onto the appliance.

Checking the water inlet hose

Check the inlet hose at least once a year. If there are

any cracks, it should be replaced immediately: during

the wash cycles, water pressure is very strong and a

cracked hose could easily split open.

Care and maintenance

Trouble shooting

Your washer-dryer could occasionally fail to work. Before contacting the Technical Assistance Centre

(see Assistance), make sure that the problem cannot be not solved easily using the following list.

Problem:

The washer-dryer does not switch on.

The wash cycle does not start.

The washer-dryer does not fill

with water.

The washer-dryer door remains

locked.

The machine continuously fills

with water and drains.

The washer-dryer does not drain

or spin.

The machine vibrates a lot during

the spin cycle.

The washer-dryer leaks.

The icons corresponding to the

Phase in progress flash rapidly

at the same time as the ON/OFF

indicator light.

There is too much foam.

The washer-dryer door remains locked.

The washer-dryer does not dry.

Possible causes / Solutions:

 The appliance is not plugged into the socket fully, or not enough to make contact.

 There is no power in the house.

 The door is not closed properly.

 The START/PAUSE button has not been pressed.

 The water tap has not been opened.

 A delayed start has been set.

 The water inlet hose is not connected to the tap.

 The hose is bent.

 The water tap has not been opened.

 There is no water supply in the house.

 The pressure is too low.

 The START/PAUSE button has not been pressed.

 If you have selected the Baby

 cycle or the Easy iron  option, when

the wash cycle has finished the machine will slowly rotate the drum; to end

the cycle press the START/PAUSE button or the Easy iron

 button. If

you have selected the Silk

 wash cycle, the machine will end the cycle

while the laundry is soaking; to drain the water so that the laundry may be

removed, press the START/PAUSE button or the Easy iron

 button.

 The drain hose is not fitted at a height between 65 and 100 cm from the

floor (see Installation).

 The free end of the hose is under water (see Installation).

 If the dwelling is on one of the upper floors of a building, there may be

problems relating to water drainage, causing the washer-dryer to fill with

water and drain continuously. Special anti-draining valves are available in

shops and help to prevent this inconvenience.

 The wall drainage system is not fitted with a breather pipe.

 The wash cycle does not include draining: Some wash cycles require the

drain phase to be started manually (see Wash cycles and options).

 The Easy iron option is enabled: to complete the wash cycle, press the

START/PAUSE button (Wash cycles and options).

 The drain hose is bent (see Installation).

 The drainage duct is clogged.

 The drum was not unlocked correctly during installation (see Installation).

 The machine is not level (see Installation ).

 The machine is trapped between cabinets and walls (see Installation).

 The load is unbalanced (see Detergents and laundry).

 The water inlet hose is not screwed on properly (see Installation).

 The detergent dispenser is blocked (to clean it, see Care and maintenance).

 The drain hose is not fixed in place properly (see Installation).

 Switch off the machine and unplug it, wait for approximately 1 minute and

then switch it back on again. If the problem persists, contact the Technical

Assistance Service.

 The detergent is not suitable for machine washing (it should display the text

for washer-dryers or hand and machine wash, or the like).

 Too much detergent was used.

 Perform the manual unlocking procedure (see Precautions and tips).

 The appliance is not plugged into the socket, or not enough to make contact.

 There has been a power failure.

 The appliance door is not shut properly.

 A DELAY TIMER has been set.

 DRYING is in the

position.

Before calling for Assistance:

 Check whether you can solve the problem by yourself (see Trouble shooting);

 Restart the wash cycle to check whether the problem has been solved;

 If it has not, contact the Authorised Technical Assistance Service.

 If the washer-dryer has been installed or used incorrectly, you will have to pay for the call-out service.

 Always request the assistance of authorised technicians.

Please have the following information to hand:

 the type of problem;

 the appliance model (Mod.);

 the serial number (S/N).

The above information can be found on the data plate located on the appliance itself.

Assistance

 Note: To exit Demo mode, press and hold the two ON/OFF and START/PAUSE buttons simultaneously for 3 seconds.

Français

Sommaire

Installation, 16-17-18-19

Déballage et mise à niveau

Raccordements eau et électricité

Caractéristiques techniques

Description de lappareil, 20-21

Tableau de bord

Comment effectuer un cycle de lavage ou un

séchage, 22

Programmes et options, 23

Tableau des programmes

Options de lavage

Produits lessiviels et linge, 24

Lessive

Triage du linge

Conseils de lavage

Système déquilibrage de la charge

Précautions et conseils, 25

Sécurité générale

Mise au rebut

Ouverture manuelle de la porte hublot

Entretien et soin, 26

Coupure de larrivée deau et du courant

Nettoyage de lappareil

Nettoyage du tiroir à produits lessiviels

Entretien du tambour

Nettoyage de la pompe

Contrôle du tuyau darrivée de leau

Anomalies et remèdes, 27

Assistance, 28

LAVANTE-SÉCHANTE

AQUALTIS

AQM9F 29 U

Mode dinstallation et demploi

! Ce symbole vous rappelle de lire ce mode d'emploi.

Installation

 Conserver ce mode demploi pour pouvoir le consulter

à tout moment. En cas de vente, de cession ou de

déménagement, veiller à ce quil accompagne toujours

le lavante-séchante.

 Lire attentivement les instructions : elles fournissent

des conseils importants sur linstallation, lutilisation et la

sécurité de lappareil.

 Cette notice, la garantie et les pièces servant à

linstallation sont réunies dans un sachet.

Déballage et mise à niveau

Déballage

1. Sitôt le lavante-séchante déballé, sassurer quil na

pas été endommagé pendant son transport.

Sil est abîmé, ne pas le raccorder et contacter le

vendeur.

2. Enlever les quatre vis de

protection pour le

transport, le caoutchouc

et la cale, placés dans la

partie arrière (voir figure).

3. Boucher les trous à laide des bouchons plastique

fournis dans le sachet.

4. Ces pièces sont à conserver car il faut les remonter

en cas de déplacement du lavante-séchante pour éviter

dendommager lintérieur de lappareil pendant le

transport.

 Les pièces demballage ne sont pas des jouets pour

enfants.

Mise à niveau

1. Poser le lavante-séchante sur un sol plat et rigide,

sans ladosser à un mur ou à un meuble.

2. Pour compenser les

irrégularités du sol, visser

ou dévisser les pieds de

réglage jusquà ce que

lappareil soit parfaitement

à lhorizontale (il ne doit

pas être incliné de plus de

2 degrés).

 Une mise à niveau minutieuse garantit une bonne

stabilité de lappareil et évite toute vibration et bruit

surtout pendant lessorage.

 Si lappareil est posé sur de la moquette ou un tapis,

agir sur les pieds de réglage de manière à ce quil y ait

suffisamment de place pour assurer une bonne

ventilation.

Raccordements eau et électricité

Raccordement du tuyau darrivée de leau

 Avant de raccorder le tuyau darrivée de leau, laisser

couler leau jusquà ce quelle soit limpide.

1. Raccorder le tuyau

darrivée de leau à

lappareil en le vissant à la

prise deau prévue, dans la

partie arrière en haut à

droite (voir figure).

2. Reliez le tuyau

dalimentation en le vissant

à un robinet deau froide à

embout fileté 3/4 gaz (voir

figure).

3. Attention à ce que le tuyau ne soit pas plié ou écrasé.

 La pression de leau doit être comprise entre les

valeurs indiquées dans le tableau des Caractéristiques

techniques (voir page ci-contre).

 Si la longueur du tuyau dalimentation ne suffit pas,

sadresser à un magasin spécialisé ou à un technicien

agréé.

 Ne jamais utiliser de tuyaux darrivée usés mais

uniquement ceux fournis avec lappareil.

Raccordement du tuyau de vidange

Raccordez le tuyau

d'évacuation, sans le plier,

à un conduit d'évacuation

ou à une évacuation

murale placés à une

distance du sol comprise

entre 65 et 100 cm;

ou bien accrochez-le à un

évier ou à une baignoire,

dans ce cas, fixez le

support en plastique fourni

avec l'appareil au robinet

(voir figure). L'extrémité

libre du tuyau

d'évacuation ne doit pas

être plongée dans l'eau.

 L'utilisation de tuyaux de rallonge est absolument

déconseillée, si vous ne pouvez vraiment pas faire

autrement vous devrez utiliser un tuyau de même

diamètre et de longueur maximum de 150 cm.

Branchement électrique

Avant de brancher votre électroménager à la prise de

courant, contrôlez que:

 la prise est bien avec terre et conforme aux

réglementations applicables en la matière;

 la prise électrique est bien apte à supporter la

puissance maximum de l'électroménager figurant

sur la plaquette des caractéristiques (voir page 19);

 la tension d'alimentation est bien comprise entre

les valeurs figurant sur la plaquette des

caractéristiques (voir page 19);

 la prise est bien compatible avec la fiche du lave-

linge. Autrement, remplacez la prise ou la fiche.

Votre électroménager dispose à présent d'une fiche

moulée 13 ampères qui peut être branchée dans une

prise compatible pour utilisation immédiate. Veuillez lire

les instructions suivantes avant d'utiliser votre

électroménager.

ATTENTION - L'ELECTROMENAGER DOIT ETRE

RACCORDE A LA MASSE. LES OPERATIONS

DECRITES CI-APRES DOIVENT ETRE EFFECTUEES

PAR UN ELECTRICIEN QUALIFIE.

Remplacement du fusible:

En cas de remplacement d'un fusible défectueux, utilisez

toujours des fusibles de 13 ampères ASTA conformes au

standard BS1362 et remontez le couvercle du fusible. Si

vous avez perdu le couvercle du fusible, n'utilisez pas la fiche

tant que la pièce manquante n'aura pas été remplacée.

Couvercles des fusibles:

Si vous remplacez le couvercle du fusible, veillez à ce que sa

couleur soit bien celle qui est indiquée par le code ou

l'indication colorée à la base de la fiche. Pour toute pièce

détachée, adressez-vous directement au centre

d'assistance technique le plus proche de chez vous.

Démontage de la fiche:

Si l'électroménager est équipé d'une fiche incorporée

qui ne peut pas être câblée à nouveau et s'il faut faire

passer le câble à travers des divisions, des unités, etc.

contrôlez que:

la fiche est bien remplacée par une autre câblable à

nouveau de 13 ampères portant la marque BSI

ou bien:

que le câble est bien raccordé directement à la prise

de 13 ampères, contrôlée par un interrupteur

(conforme BS 5733) accessible sans qu'il faille déplacer

l'électroménager.

Elimination de la fiche:

Avant d'éliminer la fiche, rendez les broches

inutilisables de manière à ce que la fiche ne puisse pas

être branchée accidentellement dans une prise.

Instructions pour le raccordement du câble à une fiche

alternative:

Important: les couleurs des fils du câble de réseau

correspondent à la codification suivante:

Jaune/Vert Terre

Bleu Neutre

Marron Alimenté

Les couleurs des fils du câble pourraient ne pas

correspondre aux indications de couleur qui identifient

les broches de la fiche, procédez comme suit:

raccordez le fil jaune/vert à la borne repérée par la

lettre E ou

ou de couleur verte ou jaune/vert

raccordez le fil marron à la borne repérée par la lettre L

ou de couleur rouge

raccordez le fil bleu à la borne repérée par la lettre N

ou de couleur noire.

65 - 100 cm

En cas d'utilisation d'une fiche de 13 ampères (BS

1363), installez un fusible de 13 ampères dans la fiche

ou sur l'adaptateur ou sur la carte de distribution.

En cas de doute sur l'alimentation électrique de votre

électroménager, faites appel à un électricien qualifié

avant de le mettre en service.

Raccordement d'une fiche alternative:

les couleurs des fils du câble de réseau correspondent à

la codification suivante:

BLEU NEUTRE (N)

MARRON ALIMENTE (L)

JAUNE/VERT TERRE (E)

Elimination de l'électroménager:

Lors de la mise au rebus de l'électroménager,

débarrassez-le de sa fiche en coupant le câble

d'alimentation le plus près possible de cette dernière et

éliminez comme décrit précédemment.

 Votre lave-linge ne doit pas être installé dehors, même

à l'abri, car il est très dangereux de le laisser exposé à

la pluie et aux orages.

 Après installation du lave-linge, la prise de courant doit

être facilement accessible.

 N'utilisez ni rallonges ni prises multiples.

 Le câble ne doit être ni plié ni écrasé.

 Le câble d'alimentation ne doit être remplacé que par

des techniciens agréés.

Attention! Nous déclinons toute responsabilité en cas de

non respect des normes énumérées ci-dessus.

GREEN &

YELLOW

BROWN

BLUE

13 ampere fuse

CROSS-BAR

CORD GRIP

.Caractéristiques techniques

Modèle

AQM9F 29 U

Dimensions

largeur 59,5 cm

hauteur 85 cm

profondeur 64,5 cm

Capacité

de 1 à 9 kg pour le lavage;

de 1 à 6 kg pour le séchage

Raccordements

électriques

Voir la plaque signalétique appliquée

sur la machine

Raccordements

hydrauliques

pression maximale 1 MPa (10 bar)

pression minimale 0,05 MPa (0,5 bar)

capacité du tambour 62 litres

Vitesse

d'essorage

jusqu'à 1200 tours minute

Programmes de

contrôle selon la

norme EN 50229

lavage: programme ; température

60°C; effectué avec une charge de 9 kg.

séchage: premier séchage effectué pour

3 kg de linge avec sélection du niveau

de séchage "

" (PRET A REPASSER);

deuxième séchage effectué pour 6 kg

de linge avec sélection du niveau de

séchage "L4" (INTENSIF).

Cet appareil est conforme aux

Directives Communautaires suivantes:

- 89/336/CEE du 03/05/89

(Compatibilité électromagnétique) et

modifications suivantes

- 2006/95/CE (Basse Tension)

- 2002/96/CE

Description de lappareil

PORTE HUBLOT

Pour ouvrir la porte, se

servir de la poignée prévue

(voir illustration).

TIROIR A PRODUITS LESSIVIELS

Le tiroir est situé à lintérieur

de lappareil et il faut ouvrir

la porte pour y accéder.

Pour le dosage des produits

lessiviels, consulter le

chapitre Produits lessiviels

et linge.

Remarque : coller sur le

tiroir létiquette contenant les

descriptions des

programmes et options. Létiquette se trouve dans la

pochette avec le présent manuel.

1. bac à produit de

prélavage : utiliser de la

lessive en poudre.

 Avant dintroduire la

lessive, sassurer que le bac

supplémentaire 3 nest pas

présent.

2. bac à produit de lavage :

utiliser de la lessive en poudre

ou liquide. Dans ce dernier

cas, il est recommandé de le

verser juste avant de démarrer le lavage.

3. Bac supplémentaire: Eau de Javel

 Lutilisation du bac supplémentaire 3 exclut le

prélavage.

bac à additifs : pour assouplissant ou additifs liquides.

Il est recommandé de ne jamais dépasser le niveau

maximal indiqué par la grille et de diluer des

assouplissants concentrés.

Stand-by

Ce lavante-séchante, conformément aux nouvelles

normes en vigueur dans le domaine de l'économie

d'énergie, est équipée d'un système d'extinction

automatique (veille) activé après environ 30 minutes

d'inutilisation. Appuyez brièvement sur la touche ON-OFF

et attendre que la machine soit réactivée.

TABLEAU DE

BORD

PORTE HUBLOT

POIGNEE PORTE

HUBLOT

SOCLE

PIEDS REGLABLES

La page charge ...

Indesit AQM9F 29 U (KW) Mode d'emploi

Marque: Indesit

Modèle: AQM9F 29 U (KW)

Catégorie: Machines à laver

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Indesit AQM9F 29 U (KW) User guide

Indesit AQM9F 29 U (KW) Mode d'emploi

Indesit AQM9F 29 U (KW) Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents