Monogram ZISB420DK Guide d'installation

Marque: Monogram

Modèle: ZISB420DK

Catégorie: Frigos

Taper: Guide d'installation

Ce manuel convient également à

Side by Side Refrigerators

Design Guide

With Installation Instructions

Installation

Instructions

monogram.com

GE is a trademark of the General Electric Company. Manufactured under trademark license.

Safety Information

BEFORE YOU BEGIN

Read these instructions completely and carefully.

• IMPORTANT – Save these instructions for local

inspector’s use. Observe all governing codes and

ordinances.

• Note to Installer – Be sure to leave these instructions

with the Consumer.

• Note to Consumer – Keep these instructions with

your Owner’s Manual for future reference.

If you received a damaged refrigerator, you should

immediately contact your dealer or builder.

Skill Level – Installation of this refrigerator requires

basic mechanical, carpentry and plumbing skills. Proper

installation is the responsibility of the installer. Product

failure due to improper installation is not covered under

the GE Appliance Warranty.

See the Owner’s Manual for warranty information.

WARNING

Electrical Shock Hazard.

Plug into a grounded 3-prong outlet.

Do not remove the ground prong.

Do not use an adapter.

Immediately replace electric cords that become frayed or

damaged.

Do not use an extension cord with this appliance.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Follow the instructions in the section Grounding the

Refrigerator.

For Monogram local service in your area, call 1.800.432.2737.

For Monogram service in Canada, call 1.800.561.3344

For Monogram Parts and Accessories, call 1.877.959.8688.

www.monogram.com

WARNING

Tip Over Hazard.

These refrigerators are top heavy, especially with any doors open, and must be secured to prevent tipping forward

which could result in death or serious injury. Read and follow the entire installation instructions for securing the

refrigerator with the anti-tip system.

WARNING

Explosion Hazard.

Keep flammable materials and vapors, such as gasoline, away from refrigerator. Failure to do so can result in fire,

explosion, or death.

WARNING

To reduce the risk associated with choking, do not allow children under 3 years of age to have

access to small parts during the installation of this product.

CAUTION

Lifting Hazard

This refrigerator is very heavy. To reduce the risk of person injury during maneuvering and installing this refrigerator, 3

people are required for proper installation of 36” wide model and 4 people are required for proper installation of a 42”

or 48” wide model.

ADVERTENCIA

Risque de basculement

Ces réfrigérateurs présentent une partie supérieure lourde, en particulier avec une porte ouverte; ils doivent donc être

fixés pour prévenir le basculement vers l’avant et le risque concomitant de blessure grave ou fatale. Lisez et suivez

les instructions d’installation complètes pour l’installation du système anti-basculement.

ADVERTENCIA

Risque d’explosion.

Conservez les matériaux et vapeurs inflammables tels que l’essence à l’écart de votre réfrigérateur. Le non-respect

de cette instruction peut entraîner un risque d’incendie, d’explosion ou de décès.

ADVERTENCIA

Pour réduire le risque d’étouffement pendant l’installation de ce produit, ne pas laisser les

petites pièces à la portée des enfants âgés de moins de 3 ans.

ATTENTION

Risque associé à la manutention d’une charge lourde

Ce réfrigérateur est très lourd. Pour réduire le risque de blessure lors de la manutention de ce réfrigérateur, trois

(3) personnes sont nécessaires pour procéder à l’installation appropriée du modèle 36 pouces, quatre (4) pour

l’installation des modèles 42 ou 48 pouces.

Consignes de Sécurité

ADVERTENCIA

Risque de choc électrique.

Branchez l’appareil dans une prise triple avec terre.

Ne retirez pas la broche de terre.

N’utilisez pas d’adaptateur.

Le non-respect de ces instructions peut entraîner des

risques d’incendies, des chocs électriques ou la mort.

Remplacer immédiatement tout cordon électrique

effiloché ou endommagé.

N’utilisez pas de rallonge avec cet appareil.

Le non-respect de ces instructions peut entraîner des

risques d’incendies, des chocs électriques ou la mort.

Suivez les instructions de la section Mise à la terre du

réfrigérateur.

Contents

Safety 2, 3

Instructions for Standard Installation 5-22

Planning Guide

The Installation Space 6

Dimensions and Clearances 6

Customization Basics 7

Side Panels 7

Refrigerator Location 7

1/4” Framed Panel Dimensions 8

3/4” Overlay Panel Dimensions 9

130° Door Swing 10

90° Door Swing 11

Dispenser Trim 12

Installation Instructions

Tools, Hardware, Materials 13

Grounding the Unit 13

Step 1. Remove Packaging 14

Step 2. Move the Refrigerator into the House 14

Step 3. Install Water Line 14

Step 4. Installation with Filtration System 15

Step 5. Install Side Panels 15

Step 6. Anti-Tip Procedures 15

Step 7. Level Refrigerator 16

Step 8. Alternate Anti-Tip Procedure 16

Step 9. Adjust Door Swing 17

Step 10. Install Grille Panel 17

Step 11. Install 1/4” Framed Panels 18

Step 11A. Install Overlay Panels 19, 20

Step 12. Connect Water Supply 20, 21

Step 13. Connect Power, Close Grille Panel 21

Step 14. Start Icemaker 21

Step 15. Install Toekick 21

Inspect Final Installation 22

Instructions for Flush Installation 23-40

Planning Guide

The Installation Space 24

Dimensions and Clearances 24

Customization Basics 25

Custom Handle Design Guide 25

Refrigerator Location 25

Side Panels 25

1/2” Overlay Panel Dimensions 26

3/4” Raised Panel Dimensions 27

3/4” Raised Door Panel Routing 28

3/4” Raised Grille Panel Routing 29

Dispenser Trim 30

Side Cleats 30

Installation Instructions

Tools, Hardware, Materials 31

Grounding the Unit 29

Step 1. Remove Packaging 32

Step 2. Move the Refrigerator into the House 32

Step 3. Install Water Line 32

Step 4. Installation with Water Filtration System 33

Step 5. Install Side Panels 33

Step 6. Install Case Trim 33

Step 7. Anti-Tip Procedure 33-34

Step 8. Level Refrigerator 34

Step 9. Adjust Door Swing 35

Step 10. Install Grille Panel 36

Step 11. Install 1/4” Framed Panels 37

Step 11A. Install Overlay Panels 38

Step 12. Connect Water Supply 39

Step 13. Connect Power, Close Grille Panel 39

Step 14. Start Icemaker 39

Step 15. Install Toekick 40

Inspect Final Installation 40

Instructions for Stainless Steel Installation 41-49

Planning Guide

The Installation Space 42

Dimensions and Clearances 42

Customization Basics 43

Side Panels 43

Refrigerator Location 43

130° Door Swing 44

90° Door Swing 45

Installation Instructions

Tools, Hardware, Materials 46

Grounding the Unit 46

Step 1. Remove Packaging 47

Step 2. Moving the Refrigerator into the House 47

Step 3. Install Water Line 47

Step 4. Installation with Water Filtration System 48

Step 5. Install Side Panels 48

Step 6. Anti-Tip Procedure 48

Step 7. Level Refrigerator 49

Step 8, Alternate Anti-Tip Procedure 49

Step 9. Adjust Door Swing 49

Step 10. Connect Water Supply 50

Step 11. Connect Power, Close Grille Panel 50

Step 12. Start Icemaker 50

Step 13. Install Toekick 51

Inspect Final Installation 51

Instructions for Standard Installation

Design Guide - Standard Installation

THE INSTALLATION SPACE

Water And Electrical Locations

The opening must be prepared with the electrical and

the cold water supply located as shown.

The Cutout Depth Must Be 24”

The refrigerator will project forward, slightly beyond

adjacent cabinetry for standard installation.

Additional Specifications

• A 115 volt 60Hz., 15 or 20 amp power supply is

required. An individual properly grounded branch

circuit or circuit breaker is recommended. Install

a properly grounded 3-prong electrical receptacle

recessed into the back wall. Electrical must be

located on the rear wall as shown.

NOTE: GFI (ground fault interrupter) is not

recommended.

• The water line can enter the opening through the

floor or back wall. The water line should be 1/4”

O.D. copper tubing or SmartConnect

™

kit between

the cold water line and water connection location,

long enough to extend to the front of the refrigerator.

Installation of an easily accessible shut-off valve in

the water line is required.

DIMENSIONS AND CLEARANCES

* Shipping height.

The refrigerator can

be adjusted to fit

into a cutout that is

84-1/2” in height.

Use leveling legs

and wheels for a

maximum 1” height

adjustment.

Product Clearances

These refrigerators are

equipped with a 3-position

door stop. The factory-

set 115° door swing can

be adjusted to 130°, or

to 90° on panel models

or 90° on stainless steel

models if clearance to

adjacent cabinets or walls

is restricted.

90° Door Swing

130° Door Swing

(Panel Models Only)

115° Door Swing

*Finished Width

Electrical

Area

85" max

Finished

Opening

75" From Floor

to Bottom

of Electrical

Area

24"

3 1/2"

Water Supply

3 1/2"

36" Models 12"

42" Models 18"

48" Models 20"

Panel Models Only: Allow minimum clearances for

the freezer door (Dimension A) and fresh food door

(Dimension B) for a full 130° door swing and to allow

for pan removal.

For a 90° door swing, allow 4” min. clearance to a

wall. If the 90° door stop position is used, pan access

is maintained, but pan removal is restricted.

See the illustrations on pages 10 and 11 to determine

door swing interaction with adjacent cabinets or

countertops.

Models A B C

36” 13” 15” 20-5/8”

42” 13” 19” 26-5/8”

48” 15” 20” 28-5/8”

*84"

From

Floor

25-3/8" Framed Models

Depth Including Handles 26-7/8”

36", 42" or 48"

Frame to Frame

35", 41", or 47"

Case Width

*83-1/2"

Rear

23-7/8"

Behind

Frame

*Min. Distance

to Wall

4”

*The finished cutout width must be:

35-1/2” for 36” models

41-1/2” for 42” models

47-1/2” for 48” models

CUSTOMIZATION BASICS:

These refrigerators are designed to be customized with decorative panels. Field installed custom door and grille

panels are required.

Optional Accessory Kits

ZKHSS2: Monogram Tubular Stainless Steel handles

designed to fit 3/4” overlay panels.

ZKHPSS1: Professional Tubular Stainless Steel handles

designed to fit 3/4” overlay panels. Kit includes one

handle. Order 2 kits for side-by-side refrigerator models

from your Monogram supplier

Design Guide - Standard Installation

SIDE PANELS

Side panels must be used

whenever the sides of

the refrigerator will be

exposed. The 1/4” side

panels will slip into the

side case trim. Secure the

panels to the refrigerator

with stick-on hook and

loop fastener strips. Order

the side panels from the

cabinet manufacturer.

• Cut a notch in the top

front corner as shown

to allow clearance for

corner keys in the front

side trim.

* Depending on installation height.

*84"

2-9/16"

24"

*3" to 4"

3/16"

1-7/8"

REFRIGERATOR LOCATION

• Do not install the refrigerator where the

temperature will go below 55°F (13°C). It

will not run often enough to maintain proper

temperatures.

• Do not install the refrigerator where temperatures

will go above 100°F (37°C). It will not perform

properly.

• Do not install the refrigerator in a location

exposed to water (rain, etc.) or direct sunlight.

• Install it on a floor strong enough to support it

fully loaded.

1/4” FRAMED PANEL DIMENSIONS

If you choose to install framed panels, they must

be cut to the dimensions shown. The panels will

slide into the frame on the door and grille.

Non-Dispenser Models

If the custom panel is less than 1/4” thick and it fits

loosely in the door frame it can be backed up with

a piece of filler material or foam tape to improve

the fit.

Fresh

Food

Panel

Freezer

Panel

Grille Panel

Dispenser

Cutout

9-5/8"

Dispenser Cutout

15-3/8

Side-by-Side (in inches)

Dispenser Cutout

Position

ABCD E F G

36” Models 33-7/8 9 68-3/8 14-9/16 18-9/16 17-13/16 3-1/8

42” Models 39-7/8 9-1/2 68-3/8 14-9/16 24-9/16 17-13/16 3-1/8

48” Models 45-7/8 9-1/2 68-3/8 18-9/16 26-9/16 17-13/16 5-1/8

IMPORTANT NOTE: Maximum total panel weight:

• Fresh food door panel – 75 lbs.

• Freezer door panel – 53 lbs.

• Grille Panel – 18 lbs.

1/4"

Panel

Door

5/16"

Trim

Reveal

The framed panel must be 1/4” nominal thickness

to fit the dispenser trim.

IMPORTANT NOTE – DISPENSER MODELS

The refrigerator is supplied with two dispenser trims, one for framed panels and one for overlay panels.

• If the panel is less than 0.250” thick, a noticeable gap may be created around the dispenser trim. Foam tape may

be applied on the door to improve the fit.

• If the panel is more than 0.250” thick, the dispenser trim cannot be secured to the door.

See Dispenser Trim Fit Example, page 12.

Design Guide - Standard Installation

36” Side-by-Side (in inches)

Dispenser Cutout

Position

ABCD E F G

1/4” Backer Panel 33-7/8 9 68-3/8 14-9/16 18-9/16

.10” Spacer Panel 33 8-3/8 67 13-1/4 17-1/4

3/4” Overlay Panel 34-1/8 9-1/4 68-5/8 14-13/16 18-13/16 17-13/16 3-1/4

42” Side-by-Side (in inches)

ABCD E F G

1/4” Backer Panel 39-7/8 9-1/2 68-3/8 14-9/16 24-9/16

.10” Spacer Panel 39 8-5/8 67 13-1/4 23-1/4

3/4” Overlay Panel 40-1/8 9-3/4 68-5/8 14-13/16 24-13/16 17-15/16 3-1/4

48” Side-by-Side (in inches)

ABCD E F G

1/4” Backer Panel 45-7/8 9-1/2 68-3/8 18-9/16 29-9/16

.10” Spacer Panel 45 8-5/8 67 17-1/4 25-1/4

3/4” Overlay Panel 46-1/8 9-3/4 68-5/8 18-13/16 26-13/16 17-15/16 5-1/4

3/4” OVERLAY PANEL DIMENSIONS

For a more custom appearance, overlay panels may

be installed on trimmed models. The overlay panel

must be secured to a 1/4” thick backer panel which

slides into the trim. A spacer panel 0.10” thick must be

placed between the overlay and backer panel.

Assemble the panels with glue and screws:

• Center the spacer panel on the backer panel, left to

right and top to bottom. Secure the panels with glue.

• Center the spacer and backer panel on the overlay

panel and secure with glue and screws. Screws

must be countersunk into the backer panel.

NOTE: Left-to-right offset

is not always equal to top-

to-bottom offset.

Spacer Panel

Overlay Panel

Backer Panel

Fresh

Food

Panel

Freezer

Panel

Grille Panel

Dispenser

Cutout

9-5/8"

Dispenser Cutout

15-3/8

*Cut the dispenser opening after the backer, spacer and overlay

panels have been assembled.

IMPORTANT NOTE: Maximum total weight for the

assembled panels:

• Fresh food door panel – 75 lbs.

• Freezer door panel – 53 lbs.

• Grille Panel – 18 lbs.

IMPORTANT NOTE – DISPENSER MODELS

The refrigerator is supplied with two dispenser trims, one for framed panels and one for overlay panels. The overlay

dispenser trim is designed to fit a total panel thickness of 1.100”.

• If the panel is less than 1.100” a noticeable gap may be created around the dispenser trim.

• If the panel is more than 1.100” the dispenser trim cannot be secured to the door.

See Dispenser Trim Fit Example, page 12.

• The overlay panel must be constructed according to the specifications shown to achieve the correct total thickness.

• Alternative panel construction methods such as securing a 3/4” panel to a 1/4” backer panel cannot

be used. Another method, routing a 3/4” thick panel on all sides, cannot be used. These methods will not result in

the required 1.100” panel thickness.

.250” + .10” + .750” = 1.100” Total Panel Thickness

3/4"

Overlay

Panel

1/4"

Backer

Panel

Door

.10"

Spacer

Design Guide - Standard Installation

1/4"

1/2"

3/4"

1-1/4"

3/4" Overlay

Panel

(Nominal Size)

Stainless Steel

1/4"

1/2"

3/4"

1-1/4"

1-1/2"

1-3/4"

2-1/4"

2-1/2"

2-3/4"

1/4"

1/2"

3/4"

Door

23-7/8" From

Rear of

Refrigerator

Case

Trim

Top View

130° DOOR SWING

Scale 1:1

IMPORTANT NOTE –

FOR DISPENSER MODELS:

Dispenser models are supplied with two

dispenser trims, one to fit framed panels and

one for overlay panels. Dispenser trim fit

to the custom panel depends on correct

panel thickness. Framed panels must

be 1/4” nominal. Overlay panels should be

constructed as shown to accomplish a total

1.100” thickness. See pages 19 and 20 for

details.

Frameless Cabinets: The case trim

overlaps cabinets at the top and sides.

Therefore, frameless cabinets may require

filler strips to prevent interfeence with

cabinet door swing. The opening must

allow for filler strips.

1/4"

1/2"

3/4"

1-1/4"

1/4"

1/2"

3/4"

1-1/4"

1-1/2"

23-7/8"

From Rear of

Refrigerator

3/4" Overlay

Panel

(Nominal Size)

Case Trim

Refrigerator

Door

Stainless Steel

Top View

90° DOOR SWING

Scale 1:1

IMPORTANT NOTE –

FOR DISPENSER MODELS:

Dispenser models are supplied

with two dispenser trims, one

to fit framed panels and one for

overlay panels. Dispenser trim

fit to the

custom panel depends on

correct panel thickness.

Framed panels must be 1/4”

nominal. Overlay panels should

be constructed as shown to

accomplish a total 1.100”

thickness

. See pages 19 and 20

for details.

Frameless Cabinets:

The case trim overlaps

cabinets at the top

and sides. Therefore,

frameless cabinets may

require filler strips to

prevent interference with

cabinet door swing. The

opening must allow for

filler strips.

Design Guide - Standard Installation

DISPENSER TRIM FIT EXAMPLES:

(NOT TO SCALE)

1/4” FRAMED PANEL

• The dispenser trim fits over the

custom panel and snaps into the

freezer door.

• The clips will not engage the door

if the panel is more than 0.250”

thick.

• If the panel is less than 0.250”

thick,

a noticeable gap may be created

around the dispenser trim.

3/4” OVERLAY PANEL

• The dispenser trim fits over the

custom panel and snaps into the

freezer door.

• The clips will not engage the door

if the panel is more than 1.100”

thick.

• If the panel is less than 1.100”

thick, a noticeable gap may be

created around the dispenser trim.

Design Guide - Standard Installation

1/4” Dispenser Trim

3/4” Overlay Dispenser Trim

TOOLS AND MATERIALS REQUIRED

• Tinsnips to cut banding

• Stepladder

• 1” Bit extension

• Tape measure

• Gloves

• 1/4” Drywall screws

• 5-Gal. Bucket with cover

• 6” Spirit level

• Appliance hand truck

• Tubing cutter

• 7/16” open-end wrench

• #2 Phillips screwdriver

• Drill and appropriate bits

• 5/16”, 7/16” socket

• Safety glasses

• 1-1/8” open end wrench

• Pliers

• 1/4”, 5/16” Combo Rachet

• 35” long 2x4 for Anti-Tip support

• 1/4” copper water line tubing or SmartConnect

™

Refrigerator Tubing kits

• Water shut-off valve

• Custom panels for doors and grille panel

• Screws to secure refrigerator to cabinetry

• Stick-on hook and loop fastener strips for 1/4” side

panels

Installation Instructions - Standard Installation

HARDWARE SUPPLIED

• Water filter bypass plug

• Toekick

• 1/4” nut and ferrule

• Dispenser trim for overlay panels (for use with

Custom Panel models).

GROUNDING THE REFRIGERATOR

WARNING

Electrical Shock Hazard.

Failure to follow these instructions can result in death,

fire, or electrical shock.

The power cord of this appliance is equipped with a

3-prong (grounding) plug which mates with a standard

3-prong (grounding) wall receptacleto minimize the

possibility of electric shock hazard from this appliance.

Have the wall outlet and circuit checked by a qualified

electrician to make sure the outlet is properly grounded.

Where a standard 2-prong wall outlet

is encountered, it is your personal

responsibility and obligation to have

it replaced with a properly grounded

3-prong wall outlet.

DO NOT, UNDER ANY

CIRCUMSTANCES, CUT OR REMOVE THE THIRD

(GROUND) PRONG FROM THE POWER CORD.

DO NOT USE AN ADAPTER PLUG TO CONNECT

THE REFRIGERATOR TO A 2-PRONG OUTLET.

DO NOT USE AN EXTENSION CORD WITH THIS

APPLIANCE.

MISE À LA TERRE DU RÉFRIGÉRATEUR

ADVERTENCIA

Risque de choc

électrique.

Le non-respect de ces instructions peut entraîner des

risques d’incendies, des chocs électriques ou la mort.

Le cordon d’alimentation de cet appareil est équipé

d’une fiche à trois broches (pour une mise à la terre)

qui s’adapte à la prise de courant standard à 3 broches

(pour une mise à la terre) pour minimiser les risques de

chocs électriques par cet appareil.

Faites vérifier la prise murale et le circuit électrique par

un électricien qualifié pour s’assurer que le système est

correctement mis à la terre.

Dans le cas d’une prise biphasée,

l’installateur a la responsabilité et

l’obligation de la remplacer par une prise

triphasée correctement mise à la terre.

NE COUPEZ PAS OU N’ENLEVEZ

PAS, SOUS AUCUN PRÉTEXTE, LA

TROISIÈME BROCHE DE MISE À LA TERRE DU

CORDON D’ALIMENTATION.

N’UTILISEZ PAS D’ADAPTATEUR POUR BRANCHER

LE RÉFRIGÉRATEUR À UNE PRISE BIPHASÉE.

N’UTILISEZ PAS DE RALLONGE AVEC CET

APPAREIL.

FLOORING

For proper installation, this refrigerator must be placed

on a level surface of hard material that is at the same

height as the rest of the flooring. This surface should

be strong enough to support a fully loaded refrigerator,

or approximately 1,500 lbs.

NOTE: Protect the finish of the flooring. Cut a large

section of the cardboard carton and place under

the refrigerator where you are working.

Installation Instructions - Standard Installation

STEP 1 REMOVE PACKAGING

WARNING

Tip Over Hazard.

The refrigerator is much heavier at the top than at the

bottom—be careful when moving. When using a hand

truck, handle from the side only.

ADVERTENCIA

Risque de

basculement Le réfrigérateur est beaucoup plus

lourd en haut qu’en bas. Il faut être prudent lors des

déplacements. Si un diable est utilisé, il faut soulever

le réfrigérateur sur le côté seulement.

• Carefully cut banding at the top and bottom, remove

the outer carton.

• Slide out the back corner posts (2).

• Slide the carton off the top of the cabinet.

NOTE: IT IS NOT NECESSARY TO LAY THE

CABINET DOWN IN ORDER TO REMOVE THE

SKID!

• The unit is secured to the

skid with 4 slotted tie-down

straps. Remove the six

7/16” bolts from the base

channels in the tie-downs.

• Remove the six 7/16” bolts

securing the straps to the

skid.

NOTE: DO NOT ATTEMPT

TO ROLL UNIT OFF SKID.

• The support blocks on the

bottom of the refrigeration

case must be removed before the refrigerator is

taken off the skid or damage will occur. Carefully

tilt the refrigerator and slide the blocks out from

beneath.

• Remove the toekick and set aside for final

installation.

• Lift the refrigerator off the skid with an appliance

dolly. Handle from the sides.

STEP 3 INSTALL WATER LINE

• A cold water supply is required for automatic

icemaker operation. The water pressure must be

between 40 and 120 p.s.i.

• Route 1/4” OD copper or SmartConnect

™

plastic

tubing between house cold water line and the water

connection location.

• The tubing should be long enough to extend to the

front of the refrigerator. Allow enough tubing to

accommodate the bend leading into the water line

connection.

Remove

Tie Downs

Toekick

Floor

Cold Water Line

NOTE: The only GE Appliances approved plastic tubing

is supplied in the SmartConnect

™

Refrigerator Tubing

kits. Do not use any other plastic water supply line

because the line is under pressure at all times. Other

types of plastic may crack or rupture with age and

cause water damage to your home.

SmartConnect

™

Refrigerator Tubing Kits are available

in the following lengths:

2’ (.6 m) WX08X10002

8’ (2.4 m) WX08X10006

15’ (4.6 m) WX08X10015

25’ (7.6 m) WX08X10025

STEP 2 MOVE THE REFRIGERATOR

INTO THE HOUSE

• Re-use the corner posts from the packaging to

protect stainless steel models. Run the appliance

dolly straps over the posts and under the handles.

• Leave the protective film on the refrigerator until

installation is complete. IMPORTANT: Never lift the

refrigerator by the handle or push against the grille

panel; this could cause damage or misalignment.

• Avoid laying the unit on its back or side to prevent

sealed system restrictions.

NOTE: Commonwealth of Massachusetts Plumbing

Codes 248CMR shall be adhered to. Saddle valves

are illegal and use is not permitted in Massachusetts.

Consult with your licensed plumber.

Shut off the main water supply.

Turn on the nearest faucet long enough to clear the line

of water.

• Install a shut-off valve between the icemaker water

valve and cold water pipe in a basement or cabinet.

The shut-off valve should be located where it will be

easily accessible.

• Turn on the main water supply and flush debris.

Run about a quart of water through the tubing into a

bucket. Shut off the water supply at the shut-off valve.

NOTE: Saddle type shut-off valves are included in

many water supply kits. Before purchasing, make sure

a saddle type valve complies with your local plumbing

codes.

STEP 4 INSTALLATION WITH

HOUSEHOLD WATER

FILTRATION SYSTEM

Skip this step if you do not have a household

water filtration system

If the water supply to the refrigerator is from any

household water filtration system, the filter cartridge

should be removed. For better ice and water

performance, remove the filter and install the filter

bypass plug.

STEP 5 INSTALL SIDE PANELS

Skip this step when not using side panels.

If you are using 1/4” side panels, they should be

inserted into the case trim. Fasten the panels to

the refrigerator with stick-on hook and loop fastener

strips before setting the refrigerator in place.

STEP 6

ANIT-TIP PROCEDURE

WARNING

Tip Over Hazard.

These refrigerators are top heavy, especially with

any doors open, and must be secured to prevent

tipping forward which could result in death or

serious injury. Read and follow the entire installation

instructions for securing the refrigerator with the anti-

tip system.

ADVERTENCIA

Risque de

basculement

Ces réfrigérateurs présentent une partie supérieure

lourde, en particulier avec une porte ouverte; ils

doivent donc être fixés pour prévenir le basculement

vers l’avant et le risque concomitant de blessure

grave ou fatale. Lisez et suivez les instructions

d’installation complètes pour l’installation du système

anti-basculement.

Installation Instructions - Standard Installation

Filter Bypass

Plug

Rotate Counterclockwise

to Remove

• Cut a 2” x 4” block, 35” long and secure the block

to the mounting brackets provided using #12 or #14

wood screws.

• Secure the bracket

with wood block to

the back wall so

that it is 84” from

the finished floor.

Use #12 or #14

wood screws. See

the illustration.

• The screws must

penetrate at least

one inch into the

vertical wall studs.

• If metal wall studs, use self-tapping sheet metal

screws in place of wood screws.

IMPORTANT: When the refrigerator is installed under

a soffit or if there is not enough height for this method

of security, brackets cannot be used. Proceed to step

7 to level the refrigerator and then to step 8 to secure

refrigerator to cabinets.

The refrigerator must be

secured to prevent tipping.

Connect Power Cord:

• Before pushing the refrigerator into the opening,

plug the power cord into the receptacle. Open the

grille panel and reach into the opening at the back

to grasp the power cord. Pull the power cord into the

opening as you push the refrigerator back.

• Gently push refrigerator into the opening with hands

against front corners.

STEP 6 ANIT-TIP PROCEDURE (Cont.)

STEP 7 LEVEL REFRIGERATOR

All models have 4-point leveling. The front is

supported by leveling legs, the rear is supported by

adjustable wheels. Both are accessible from the front

of the refrigerator.

• To level the back of the refrigerator, turn the 7/16”

hex nut located above the front wheels. Turn

clockwise to raise or counterclockwise to lower the

refrigerator.

• For front leveling, use a

1-1/4” open-end wrench.

• Adjust height of refrigerator

to match installation cutout

opening 84-1/2”. The

refrigerator should be level

and plumb with cabinetry.

NOTICE: The rear leveling

wheels and front leveling legs are limited to a

maximum height adjustment of 1”. If the installation

requires more than 84-1/2” height, the installer should

elevate the refrigerator on a sheet of plywood or

runners. Cabinetry trim could also be added across

the top of the opening to shorten the opening. If you

attempt to raise the refrigerator more than 1”,

you will damage the front leveling legs and the

rear leveling wheels. Make adjustments in small

increments.

Installation Instructions - Standard Installation

STEP 8 ALTERNATE ANTI-TIP

PROCEDURE

The refrigerator must be secured to prevent tipping.

• Raise the grille panel to access case trim.

• Use a 3/16” bit to drill four evenly spaced clearance

holes through the metal top case trim.

• Use a 1/16” bit to drill to pilot holes through the metal

clearance holes and into the wood soffit. The holes

should be centered in the soffit or a 3/4” min. wood

brace. The brace spanning the enclosure must be

securely fastened to cabinets on both sides.

• Install four, 1-1/2” drywall screws into the pilot holes.

• Drill screws into adjacent cabinets through side case

trim.

Installation Instructions - Standard Installation

STEP 9 ADJUST DOOR SWING

NOTE: This refrigerator has a 3-position door stop:

90°, 115°, and 130°. When space does not allow the

door to swing open fully to 115°, you may change

the door swing to a 90° opening. A 130° door swing

option is available for standard installation only. Skip

this step if door opening is satisfactory for your

installation situation.

• Open the door to view the bottom hinge. Note the

door stop pin locations. The pin is factory installed in

the 115° position.

• Close the door. From below, use pliers to unscrew

the door stop and reinstall into the 130° or 90°

position.

STEP 10 INSTALL GRILLE PANEL

To insert the framed or overlay panel into the

grille:

• Raise the grille panel to the stop position.

Adjust Nut Below

Spring to Accommodate

Panel Weight

Loosen

Side

Trim

Screw

Loosen

Side

Trim

Screw

• Loosen the screws on the side trim behind the frame.

Remove the bottom trim.

CAUTION

SHARP EDGE HAZARD

The metal panel may be slippery. Grip the metal panel

firmly so the panel does not slip out of the frame and

cause personal injury or damage to the frame.

ATTENTION

RISQUE DE COUPURE : ATTENTION

AUX ARÊTES VIVES

Le panneau en métal peut bêtre glissant. Tenir

fermement le panneau en métal, de manière à ce

que le panneau ne glisse pas en dehors du cadre en

provoquant des blessures corporelles ou des dommages

au cadre.

• Slide the panel over the metal backer panel and into the

trim.

• If necessary, tap with a wood block until the panel slips

under the top trim piece.

• Reassemble the bottom trim. Tighten the screws.

• Adjust the hinge spring to accommodate the panel

weight, if necessary.

STEP 11 INSTALL 1/4” FRAMED PANELS

Install door panels:

• Open the door to 90°. Remove the 6 Phillips head

screws from the door handle.

• Remove the handle. Retain all screws.

• Remove the 6 screws holding the trim, then lift off the

trim. Retain the screws.

• Slide the framed panel into the door trim.

Dispenser Models Only:

• The dispenser controls protrude beyond the face of the

freezer door. To avoid damage to the dispenser, the

trim at the top of the door should be removed.

• Remove the screws holding the top trim in place.

• Place the freezer panel into the bottom channel and

slide into the hinge side trim.

• Reinstall the top trim piece with screws.

• There are two sets of holes in the handle side trim.

Replace the handle side trim by installing the original

screws in the FRONT screw holes.

• Secure the handle to the door using the REAR screw

holes.

• Follow the same procedures to install the opposite

panel.

• Check to be sure the handles are evenly aligned with

each other at the top. To adjust, loosen the handle

screws and slide up or down. Tighten the screws.

NOTE: Aluminum cover trim is supplied for use with

custom handles on overlay panels. It is not intended for

use with 1/4” panels. Discard the cover trim when using

1/4” framed panels.

Go to Step 12A for Overlay Panels

Supplied Handle

Shown in 1/4”

Panel Position

Installation Instructions - Standard Installation

STEP 11A INSTALL OVERLAY PANELS

Install door panels:

• Open door to 90°. Remove the 6 Phillips head screws

from the door handle.

• Remove the handle. Retain all screws.

• Remove the 6 screws holding the trim, then lift off the

trim. Retain the screws.

• Slide the overlay panel into the door trim.

Dispenser Models Only:

• The dispenser controls protrude beyond the face of

the freezer door. To avoid damage to the dispenser,

the trim at the top of the door should be removed.

• Remove the screws holding the top trim in place.

• Place the assembled freezer panel into the bottom

channel and slide into the hinge side trim.

• Reinstall the top trim piece with the screws.

• There are two sets of holes in the handle side trim.

Replace handle side trim by installing the original

screws in the REAR screw holes.

• Secure the handle to the door using the FRONT

screw holes.

• Follow the same procedures to install the opposite

panel.

• Check to be sure the handles are evenly aligned with

each other at the top. To adjust, loosen the handle

screws and slide up or down. Tighten the screws.

Supplied Handle

Shown in Overlay

Panel Position

Installation Instructions - Standard Installation

STEP 12 CONNECT WATER SUPPLY

• Locate and bring the tubing to the front of the cabinet.

• Turn the water on to flush debris from the line. Run

about a quart of water through the tubing into a

bucket, then shut off the water.

Copper Tubing:

• Slip a 1/4” nut and ferrule (provided) over both ends of

the copper tubing. Insert the tube into the union fitting

on the unit and tighten the nut to the union.

• Turn on the water to check for leaks.

SmartConnect

™

Tubing:

NOTE: The only GE Appliances-approved plastic tubing is

supplied in the SmartConnect

™

Refrigerator Tubing kits.

Do not use any other plastic water supply line because

the line is under pressure at all times. Other types of

plastic may crack or rupture with age and cause water

damage to your home.

SmartConnect

™

Refrigerator Tubing Kits are available in

the following lengths:

Refrigerator

Water Supply

House

Water Supply

Installation Instructions - Standard Installation

STEP 11A INSTALL OVERLAY PANELS

(continued)

Custom Handles

• If you are using custom handles, the handle must e

properly secured to the overlay panel before sliding

the panel into the trim.

• The cabinet manufacturer will supply the custom

handle and hardware.

• Discard the supplied handle.

• Remove the trim. Peel away a few inches of the

adhesive backing.

IMPORTANT: The tape is very sticky and strong.

Once it adheres to a surface, it cannot be removed

without damaging both surfaces. Do not install the

trim before the final wood panels are in place. Be

sure to align the trim carefully before removing the

paper backing.

• Reinstall the handle side trim, using all 12 supplied

flat-head screws, plus the 12 flat-head screws

originally installed in the handle trim.

• Install a supplied end cap onto the top of the door,

using a Phillips head screwdriver and the 2 screws

provided. Hand-tighten the screws into the end

caps. Do not overtighten; damage will occur.

• Clean the aluminum trim with rubbing alcohol—

do not use alcohols with oil or lanolin that will prevent

adhesion of double-sided tape.

• Slip the aluminum cover onto the top bracket to check

the fit. The aluminum cover trim has a slot on each

end which fits the bracket.

Reinstall all original screws.

STEP 11A INSTALL OVERLAY

PANELS (continued)

• Carefully place the aluminum cover trim onto the top

bracket so that the bracket is inside the cover trim.

Use the top to bottom grooves along the handle side

to align the cover trim accurately. Align the bracket

with the screw holes in the top of the door. Pull the

tape a few inches at a time while pressing the trim

against the door. Press and hold approximately 10

seconds before continuing along the length of the

door.

• Install another bracket at the bottom of the door to

secure the cover trim. Use a stubby Phillips head

screwdriver and the 2 screws provided.

• NOTE: Make sure there are no gaps in the

installation.

• Follow the same procedure on the opposite door.

Secure top

bracket with

2 screws.

Top Bracket

Slide aliminum

trim over top

bracket.

La page charge ...

Monogram ZISB420DK Guide d'installation

Marque: Monogram

Modèle: ZISB420DK

Catégorie: Frigos

Taper: Guide d'installation

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Monogram ZISB420DK Installation guide

Monogram ZISB420DK Guide d'installation

Ce manuel convient également à

Monogram ZISB420DK Guide d'installation

dans d''autres langues

Documents connexes

Autres documents