LED WORLD LIGHTING QS-RD-COB3W-12V 3W LED Puck Light Recessed Mount Manuel utilisateur

Taper
Manuel utilisateur
IMPORTANT INSTRUCTIONS
1/2
1-800-387-4081
ledworldlighting.com ledworld.ca |
LED PUCK LIGHT (Recessed/Surface Mounted)
WARNING: Always connect the LED light to the power supply rst and then connect the power supply to the mains. Failure to do so may cause damage
to the existing diode.
CAUTION: To reduce the risk of electric shock:
ŸRoute the low voltage wire from the light so that they will not be damaged or pinched when the cabinet is installed (pushed to the wall).
ŸNot intended for recessed ceiling installation or softs.
Low voltage portable cabinet light maybe installed in furniture or cabinets when:
ŸThe power supply is located outside cabinets and is not concealed (this does not apply to the wiring between the light and the power supply).
ŸWhen the low voltage wire are not concealed or pass through the structure of the building (concealed behind the wall) where it may be inaccessible for
examination or where damage to may go unnoticed.
Installation instructions:
ŸUse only insulated staples or plastic ties to secure cords.
ŸCords should be visible and examined regularly.
ŸMust be installed by a qualied licenced electrician.
ŸTurn power off prior to installation.
ŸInsert the light into the hole; ction t light will lock in place.
ŸRoute the low voltage wiring through the hole.
ŸPlug the light’s low voltage wiring into the class 2 LED power supply. (# , # - sold separately).MD-012-060VTDHV2 MD-012-030VTDHV2
ŸBore a hole Ø2.36” (60mm) minimum recess depth required 5/8” (15mm).
ŸFermez l'alimentation électrique avant de procéder à l'installation.
MISE EN GARDE: An de prévenir les risque incendie ou de choc électrique:
ŸN'utilisez que des crampons isolés ou des attaches en plastique pour xer les cordons.
Les baladeuses de basse tension peuvent être installée dans un meuble ou dans une armoires lorsque:
ŸL'alimentation électrique est située à l'extérieur des armoires et n'est pas dissimulée (ceci ne s'applique pas au câblage entre le luminaire et l'alimentation
électrique).
ŸLe câble de basse tension n'est pas dissimulé ou passé à travers la structure de l'immeuble (dissimulé derrière le mur), le rendant inaccessible pour une
verication et ou des dommages pourraient passer inaperçus.
ŸLes cordons doivent être visibles et examinés régulièrement.
ŸPassez le câble de basse tension à partir du luminaire an de ne pas l'endommager ou de le coincer une fois l'armoire installée (poussée contre le mur).
ŸN'est pas conçu pour l'installation de luminaires encastrés au plafond ou les softes.
Instructions d'installation:
ŸPour de meilleurs résultats, ayez recours aux services d'un électricien agréé qualié pour une installation professionnelle de votre luminaire.
ŸPercez un trou de Ø2.36" (60mm) profondeur de l'embrasure minimum requise de 5/8" (15mm).
ŸPassez le câble de basse tension à travers le trou.
ŸInsérez le lumière dans le trou an de xer solidement le luminaire en place.
ŸBranchez le câbe de basse tension du lumière dans la l'alimentation LED classe 2. (# , # - vendu séparément).MD-012-060VTDHV2 MD-012-030VTDHV2
MISE EN GARDE: Il faut toujours brancher le luminaire DEL à source d'alimentation en premier et ensuite brancher l'alimentation à la source principale
d'alimentation électrique. Le défaut de le faire pourrait causer des dommages à la diode en place.
INSTRUCTIONS IMPORTANTES
If a product is defective, we will replace the product with similar or identical product or at our option a credit towards a future purchase. To make a claim under this warranty, obtain a return authorization number.
LED WORLD INC. warranties this product for three year (some exceptions may apply) from the date of shipping unless otherwise noted in writing. This warranty is expressly in lieu of all other warranties expressed or
implied. Under this Limited Warranty, the obligation of the company is limited to replacing on a prorated basis, at its option, any component found to be defective. This Limited Warranty does not apply to damage
caused by buyer or alteration to the product or incorrect power supply. Factory warrantees are covered by the original manufacturer and claims must be submitted to them.
LED World Inc. And its providers will never be liable to you or any other person for any indirect, incidental, consequential, special, punitive or exemplary loss or damage arising from, connected with, the purchase
of products, including but not limited to loss of data, business, markets, cost of labour, savings, income, profits, use, production, reputation or goodwill, anticipated or otherwise, or economic loss, under any theory
of liability (whether in contract, tort, strict liability or any other theory or law or equity), regardless of any negligence or other fault or wrongdoing (including without limitation gross negligence and fundamental
breach) by led world inc. Or any person for whom led world inc. Is responsible, and even if led world inc. Has been advised of the possibility of such loss or damage being incurred.
THREE YEAR LIMITED LIGHTING WARRANTY
Model : QS-RD-COB3W-12V
Copyright © 2022 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA | Version 2.2 - 09/28/22
For Under Cabinet lighting and Under Counter Top Lighting
ŸTurn off the power at breaker.
SURFACE MOUNTING:
RECESSED MOUNTING:
ŸTurn off the power at breaker
ŸConnect light to the Class 2 driver, see g 2.
ŸInsert the recessed puck light into the cut hole, see g 1a.
ŸInsert the recessed puck light back into the surface mount ring, see g 1b.
ŸTurn on the power.
ŸDrill a Ø60mm hole through cabinet or shelf, see g 1.
ŸConnect light to the Class 2 driver, see g 2.
ŸTurn on the power.
ŸTake the surface mounting ring off the tting, see g 1b.
ŸMount the ring to surface with the attached screws, pay attention to the direction of the notch for the cord, see g 1b.
120V AC
Case enclosure wire must be grounded
Recessed Mounting Surface Mounting
1
1
1
2
V+
V- (Dotted line Wire)
2
Cut end connector before connecting to power supply
1-800-387-4081
ledworldlighting.com ledworld.ca |
LED PUCK LIGHT (Recessed/Surface Mounted)
2/2
Model : QS-RD-COB3W-12V
Copyright © 2022 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA | Version 2.2 - 09/28/22
INPUT
100~277VAC
OUTPUT
12VDC
V+V-
Red Wire (V+)
Black Wire (V-)
Green Wire
Ground
G
0-10V
Dimming
Grey Wire (-)
Purple Wire (+)
Not used
Leave caps on
Serial Connection (Max. 10 pcs in a continuous run) Power In
Male End
Female End
  • Page 1 1
  • Page 2 2

LED WORLD LIGHTING QS-RD-COB3W-12V 3W LED Puck Light Recessed Mount Manuel utilisateur

Taper
Manuel utilisateur