Bushnell NatureView Cam HD Essential 119739 Manuel utilisateur

INSTRUCTION MANUAL

Model#: 119739 11-14

VIDEO

2

3

TABLE OF CONTENTS PAGE #

ENGLISH

FRANÇAIS

ESPAÑOL

DEUTSCH

ITALIANO

4-36

37-76

77-113

114-154

155-193

IMPORTANT NOTE

Congratulations on your purchase of one of the best trail cameras

on the market! Bushnell is very proud of this little unit and we

are sure you will be pleased with it as well. We appreciate your

business and want to earn your trust. Please refer to the notes

below and the instructions in this manual to ensure that you are

completely satisﬁed with this product.

If your Bushnell NatureView HD Essential does not seem

to be functioning properly or if you are having photo/video

quality issues, please check the Troubleshooting/FAQ

section on pages 29-33.

Problems are often due to something simple that was

overlooked, or require only changing one setting to solve.

If your problem continues after trying the solutions in

the Troubleshooting/FAQ section, please call Bushnell

Customer Service at (800) 423-3537. In Canada, call (800)

361-5702.

Bushnell recommends using 8 Energizer

®

Lithium AA batteries in

this NatureView HD Essential model to obtain maximum battery

life

Do not mix old and new batteries

Do not mix battery types-use ALL lithium or ALL alkaline

Rechargeable batteries are NOT recommended

Bushnell recommends using SanDisk

®

SD and SDHC Cards

(up to 32GB capacity) in all NatureView HD Cameras

5

INTRODUCTION

About the NatureView HD Essential

The Bushnell NatureView HD Essential is a digital scouting camera. It

can be triggered by any movement of game in a location, detected by a highly

sensitive Passive Infra-Red (PIR) motion sensor, and then take high quality

pictures (up to 12MP still photos), or video clips.

The NatureView HD Essential consumes very little power (less than

300mA) in a stand-by (surveillance) state. This means it can deliver up to

six months stand-by operation time when the device is powered by eight

AA alkaline batteries, and up to twelve months utilizing lithium AA batteries.

Once motion in the monitored area is detected, the digital camera unit will

be triggered at once (typically less than 0.5 second) and then automatically

take photos or videos according to previously programmed settings. The

NatureView HD Essential is equipped with built-in infrared LEDs that

function as a ﬂash, so that it delivers clear photos or videos (in black & white)

even in the dark, and it can take color photos or videos under sufﬁcient

daylight. The NatureView HD Essential is designed for outdoor use and

is resistant against water and snow. Your trail camera is one of the latest

generation of Bushnell NatureView HD Essentials, and includes many

new or improved features, such as:

• Auto PIR Sensitivity-the camera monitors ambient temperature

conditions and automatically adjusts the sensor/trigger signal to be

more sensitive to slight variations in temperature on hot days, less

sensitive on cold days.

• Field Scan 2x with Live Trigger-The “time lapse” feature added in last

year’s models has been enhanced with the addition of the option for

a second block of recording with its own start/stop times. Trigger

signals generated by nearby wildlife activity will still generate additional

photos/videos as they normally would, independently of the Field Scan

operation.

• Audio Recording capability in Video Mode. 720p HD Video.

Applications

The NatureView HD Essential can be used as a trail camera for hunting or

scouting game. It is also suitable for surveillance usage.

ENGLISH

6

PARTS AND CONTROLS

The NatureView HD Essential provides the following connections for

external devices: USB port, SD card slot, TV Out, and external DC power

in (Fig. 1).

A 3-way power switch is used to select the main operating modes: OFF,

SETUP, and ON (Fig. 2).

A control key interface with six keys is primarily used in SETUP mode to

select operational functions and parameters. As shown in Fig. 2, these keys

are: UP, DOWN, LEFT, RIGHT, OK and MENU. Four of the keys can also

perform a second function (shortcut operations in SETUP mode) in addition

to their main function: The DOWN key can be used to set the camera to

Photo mode (still camera icon), and the UP key can set the camera to Video

mode (movie camera icon). The RIGHT key also serves as the manual shutter

(“SHOT”) button of the camera and the OK key switches the camera to

the Playback (“REPLAY”) mode. These secondary functions are indicated by

icons or text above the key as shown in Fig. 2.

Fig. 2: Button and

Switch Guide

ON

SETUP

OFF

BACK VIEW

LCD Screen

Power/Mode

Switch

UP/Video

DOWN/Photo

LEFT

MENU

OK/Replay

RIGHT/Shot

Cable to Battery

Compartment

7

Tripod Socket

DC in

Cover Plug

Video Mic

Fig. 1: Connections

USB Port

SD Card Slot

DC In

TV Out

Video Mic

PARTS AND CONTROLS

FRONT VIEW

LED IR Flash

Motion/ Low

Battery Indicator

Lens

Lock Hole

PIR Sensor

8

INSTALLING THE BATTERIES AND SD CARD

Before you begin learning how to use your NatureView HD Essential, you

will ﬁrst need to install a set of batteries and insert an SD card. Although

that may only take you a minute, there are some important notes about both

batteries and SD cards you should be aware of, so please take the time to

read the following directions and cautions:

Loading Batteries

After opening the two latches on the right side

of the NatureView HD Essential, you will see

that the NatureView HD Essential has eight

battery slots. Starting at the top of the battery

compartment, slots 1, 2, 3 and 4 form one group,

while slots 5, 6, 7 and 8 form the other group,

each providing 6 volts in parallel. For maximum

battery life, you should install a full set of eight

batteries. The NatureView HD Essential may

also be operated by just four batteries installed

in the top group only (see right), starting at slot

1. Battery life will be shorter with 4 batteries, but

the camera will operate normally. Whether you

use 4 or 8, be sure to insert each battery with correct polarity (negative or

“ﬂat” end against the long spring of each battery slot).

Bushnell recommends using eight new lithium AA (Energizer

®

brand) or

alkaline AA batteries. NiMh Rechargeable batteries can also be used, but

they might have a shorter life span due to their reduced efﬁciency over time

and at low temperature. It is also possible to use a lead-acid external battery cell

with 6V output or suitable AC adapter-see below for more details.

Using an External Power Source (optional, user provided)

Optionally, you can connect an external 6V DC power source to the “DC In”

jack at the bottom of the NatureView HD Essential. It is recommended to

use a power source with a current output greater than 1000mA. However,

during bright daytime operation when no ﬂash is required, the NatureView

HD Essential can function with much less current (>400mA). Please use

a compatible power source cable (not provided) to connect the external DC

power source with the power input jack of the NatureView HD Essential,

making sure that the polarity is correct. Note: The power connector is a

9

4.0x1.7mm coaxial DC power plug with positive “tip” (inside pin) polarity

(Radio Shack P/N 274-1532 or equivalent).

If both an external power source is connected and batteries are installed, the

NatureView HD Essential will be powered by the external power source.

When the batteries become weak, the low-battery indicator LED will glow

blue, indicating the batteries should be changed (pg 7, “Front View”).

Inserting the SD Card

The NatureView HD Essentials have 32MB internal memory, which can

hold only about 10 photos (@ 5MP resolution). This is handy for testing and

getting familiar with the camera, but you will no doubt want to leave the camera

unattended for longer than a day, so using an SD card is recommended. Insert

the SD card (with the camera’s power switch in the OFF position) before

beginning to operate the camera. Don’t insert or remove the SD card when

the power switch is in the ON position.

The NatureView HD Essential uses a standard SD (Secure Digital) memory

card to save photos (in .jpg format) and/or videos (in .avi format). SD and

SDHC (High Capacity) cards up to a maximum 32GB capacity are supported.

Before inserting the SD card into the card slot after opening the camera’s

front cover, please make sure that the write-protect switch on the side of the

card is “off” (NOT in the “Lock” position). The following describes how to

insert and remove the SD card:

• Insert the SD card into the card slot with its label side upwards (see

above). A “click” sound indicates that the card is installed successfully.

If the wrong side of the card is facing up, you will not be able to insert

it without force-there is only one correct way to insert cards. If the SD

card is not installed correctly, the device will not display an SD card icon

on the LCD in SETUP mode (the SD card icon displayed after switching

to SETUP mode will have a “lock” symbol inside it in it if the card is locked).

Formatting the SD card by using the NatureView HD Essential’s

“Format” parameter before using it for the ﬁrst time is recommended,

especially when a card has been used

in other devices (see “Changing Menu

Parameter Settings” for details).

• To take out the SD card, just gently push

in the card (do not try to pull it out without

pushing in ﬁrst). The card is released from

the slot and ready to be removed when you hear the click. Be sure the

10

camera’s power is switched OFF before inserting or removing SD

cards or batteries.

USING THE NatureView HD Essential

Once you’ve prepared your NatureView HD Essential by properly installing

batteries and an SD card, you could simply take it outside, strap it to a tree,

switch it on and leave-and you might get some great photos that are exactly

what you wanted. However, we highly recommend that you ﬁrst spend some

additional time indoors with this manual and your camera until you know a

bit more about what the 3-way switch and those control keys do. If nothing

else, you’ll probably want to at least set the date and time so the camera will

imprint them (or not-it’s your option) on your photos as they are taken, learn

how to set the camera to shoot video clips instead of still photos if you like,

and read some tips about mounting it on a tree.

THE OFF, ON, AND SETUP MODES

The NatureView HD Essential has three basic operational modes:

• OFF mode: Power switch in the OFF position.

• ON mode: Power switch in the ON position (LCD screen is off.)

• SETUP mode: Power switch at SETUP position (LCD screen is on).

OFF MODE

The OFF mode is the “safe” mode when any actions must be taken, e.g.,

replacing the SD card or batteries, or transporting the device. You will also

use OFF mode if you connect the camera to a computer’s USB port later

to download your photos/videos. And of course, when you are storing or

not using the camera, you will switch it to OFF. Please note that even in the

OFF mode the NatureView HD Essential still consumes power at a very

low level. Therefore, it’s a good idea to take the batteries out of the battery

compartment if the camera will not be used for a long time.

ON MODE

Anytime after the batteries and SD card have been inserted, you can switch

on the camera. When the power switch is moved to the top position, the

camera will enter into the ON (Live) mode. The motion indicator LED (pg. 7,

“Front View”) will blink red for about 10 seconds. This interval allows time for

11

you to close the NatureView HD Essential’s front cover, lock it, and leave

the monitored area. Once in the ON mode, no manual controls are needed or

possible (the control keys have no effect). The NatureView HD Essential

will take photos or videos automatically (according to its current parameter

settings) when it is triggered by the PIR sensor’s detection of activity in the

area it covers.

You can either move the power switch directly from OFF to ON mode, or

stop at the SETUP position ﬁrst to change one or more settings, then move

the switch to ON after you have ﬁnished doing so.

SETUP MODE

In the SETUP mode you can check and change the settings of the

NatureView HD Essential with the help of its built-in LCD (or a monitor

connected to the TV out jack). These settings, found in the SETUP Menu,

let you change the photo or video resolution, interval between photos, switch

the time imprint on, etc. Moving the power switch to the SETUP position will

turn on the LCD display, and you will see an information screen that shows

how many images have been taken, the battery level, camera or video mode,

etc (see Fig. 3, pg. 12).

NOTE: Always move the power switch from OFF to SETUP mode. It

is possible that the camera could lockup if it is switched from ON to

SETUP mode. If this occurs, simply move the switch to OFF and then

push it up to SETUP again.

SETUP Mode Shortcut Keys/Functions

As mentioned earlier in “Parts & Controls”, four of the keys below the LCD

have secondary, “shortcut” functions when the camera is switched to

SETUP mode (but the MENU key has not been pressed):

• Press the UP key to quickly set the camera to shoot video clips.

• Press the DOWN key to quickly set the camera to take still photos.

• Press the RIGHT key to manually trigger the shutter. This is useful

for testing the camera-make sure you are in SETUP mode, press the

RIGHT key, and a few seconds later a photo or video (depending on

how the camera was set) will be saved to the SD card (or internal

memory if no card is inserted). The “number of images taken” counter

on the bottom left of the LCD will increase by one. If the display

indicates “SD PROTECTED” when you press the SHOT key, switch

the camera OFF, remove the SD card and slide its protect switch off.

12

5

Fig. 3: SETUP Information Screen

Still Photo Mode

Time Stamp

Field Scan On

# of Photos Taken Remaining Photo Capacity

Date:Month-Day-Year

Battery Level

Image Size (Resolution)

SD Card Status

Time

Hour:Minute:Second

Camera (Still Photo) Mode

Video Mode

Video Sound On

Video Resolution

Available Video Recording Time

Video Mode

13

• Press the OK key to replay (review or playback) photos/videos on a

connected TV monitor. See “Playing Back Photos/Videos” for more

details.

USING THE SETUP MENU TO CHANGE

SETTINGS

The main purpose of the SETUP mode is to allow you to change the

settings of the camera’s parameters (14 different ones are available) so your

NatureView HD Essential operates exactly the way you want it to. You will

do this by entering the SETUP Menu and pressing the keys below the LCD

display, which will show you each parameter and its setting.

Changing Parameter Settings in SETUP Mode

A wide range of options or “parameters” are provided to allow you to set

the NatureView HD Essential to your operational preferences. To change

the setting of any parameter you must ﬁrst switch to the SETUP mode.

Once in SETUP mode, pressing the MENU button will allow you to select

any parameter and change its setting. The name of the parameter and its

current setting will be shown on the LCD. Pressing the RIGHT or LEFT

key scrolls to the next or previous parameter (RIGHT key to move on to the

next parameter and LEFT key to go back to the previous parameter), and

pressing the UP or DOWN key lets you select a different setting for the

currently displayed parameter. Once you have selected your preferred new

setting for a parameter, press the OK button to save the new setting (actually

change it). When have are ﬁnished changing the settings of one or more

parameters, press MENU again to exit the SETUP menu. MENU can also

be pressed anytime you want to cancel changing a parameter’s setting after

a new setting has been selected (but OK has not been pressed yet). After

setting the parameters to your preferences, be sure to move the switch to

ON to begin actually taking photos or videos. No images will be captured if

the switch is left in the SETUP position (unless you press the RIGHT/Shot key

after exiting the menu)-in fact, the camera will power off automatically after a

few seconds with no key pressed.

14

Fig. 4: Selecting Parameter Settings

(4a)

(4b)

Press MENU

Press DOWN to select new setting

for the highlighted parameter

Press OK to conﬁrm and execute

the new setting

Parameter Display

The settings for a parameter are shown on the display as follows:

Only one setting is displayed at a time, starting with the current setting

for the parameter when it is ﬁrst selected (Fig. 4a). To change the

setting, use the UP/DOWN keys to display the new setting you want

(Fig. 4b), then press OK to “Execute” (make the actual change to this

setting). If you want to conﬁrm this setting is now the current one, just

press the RIGHT key to scroll to the next parameter, then press LEFT

to go back again to the previous one. You should see the parameter

setting you just made.

15

EXAMPLES-Changing the Settings of Some Common Parameters

Following this page, you will ﬁnd tables listing all of the parameters found in

the SETUP Menu, along with their possible settings (or range of settings),

and a detailed description of what the parameter controls and what

the settings do. If you read the previous section detailing how to select

parameters and change their settings, you should be able to dive right in, ﬁnd

the parameter(s) you want, and setup the camera to your preferences. But

maybe you’d rather walk through an example or two ﬁrst:

To change any parameter’s setting, always start with the power switch in the

SETUP position. After the LCD comes on, press the MENU key.

The ﬁrst parameter you will see when you ﬁrst enter the SETUP Menu is

“Mode”. To change it from its default setting of “Camera” (still photos) to

“Video” (shoot video clips), press the DOWN key to select the “Video”

setting. Press the OK key to “Execute” (Set) the new setting you’ve selected

for this parameter.

Now press the RIGHT key to move to another parameter in the Menu.

Pressing it four times will take you to “Video Length”. Try using the UP and

DOWN keys to scroll through the range of settings, then press OK to lock in

your setting for the length of each video clip the camera shoots.

Pressing the RIGHT key several more times will get you to the “Default Set”

parameter. Highlight or select “Execute” (using UP or DOWN) and press OK

to restore all parameters (including the Mode and Video Length parameters

you changed a minute ago) back to their original factory default settings. The

default settings for each parameter are indicated in bold type in the SETUP

Menu tables on the next several pages.

Be sure to set the current date and time, using the “Set Clock” parameter,

if you choose to change the “Time Stamp” parameter setting to “On” since

that will tell the camera to imprint the date and time on each of the images

it captures.

16

Field Scan 2x with Live Trigger Feature

Field Scan is a revolutionary new feature for the Bushnell NatureView

HD Essential, which allows you to monitor your food plots or ﬁeld edges

with time lapse images or video. When set to “On”, the NatureView HD

Essential will take a photo (or record a video clip) automatically at your

choice of intervals (for example, once every ﬁve minutes) during one or two

blocks of time you set up for each day, without requiring a trigger from

an active animal. This has the advantage of giving you the ability to monitor

the edge of a ﬁeld that might be 50 or 150 yards away from the camera out

of the PIR sensor’s range. The result is an effective range much greater than

it would normally be, with the camera dependant on triggers generated by

nearby animals. This is a great tool for hunters to scout an entire ﬁeld with

only one camera.

If an animal does enter the area covered by the PIR sensor and generate a

trigger event during a time in between the Field Scan intervals you set, the

camera will capture an image or video just as it normally would, based on

your other menu settings. Here’s how to setup and use Field Scan (be sure

you’ve set the current time in “Set Clock” ﬁrst, so your Field Scan recording

will stop and start at the correct times of day):

1. Move the main switch to SETUP, then press MENU.

2. Keep pressing the RIGHT key, stepping through the Setup Menu until

you reach Field Scan.

3. Press the UP key to select On, and press OK (Step 1, pg.18). You will

see "A", representing the ﬁrst block of time you can deﬁne (a second

block of time later in the day, "B" can also be setup if you wish). Press

OK (Step 2). This takes you to the screen to set Start and Stop times,

which determines the clock times when the ﬁrst block of Field Scan

recording will begin and end for each day. You can set these times to

the exact hour and minute you want, for a recording “window” that

lasts anywhere from just a minute to a full 24 hours.

4. Set the [Start] and [Stop] times, beginning with the Start hour, using

the UP/DOWN keys to change the setting (Step 3). The hour setting

is based on a 24-hour clock, with “00” hours = midnight, “12” hours

= noon, “23” hrs = 11PM, etc. To move to the next setting, press the

RIGHT key, change the minute for the Start time with UP/DOWN,

then on to the hour and minute settings for the Stop time.

17

Note: avoid any "overlap" of Field

Scan A & B recording blocks when

setting their start and stop times,

to assure correct operation.

5. After you ﬁnish setting the Stop minutes, press OK to conﬁrm your

settings for the ﬁrst block of Field Scan recording. If desired, you can

create a second block of time by pressing the DOWN key to select

"B" (Step 4), then press OK and follow the same process to set Start

and Stop times for Field Scan block "B" (Step 5). As an example of

how you might use these two available time blocks, you could setup

Field Scan time block "A" for the dawn hours from 6 AM to 8 AM, and

block "B" to capture images between 5:30 and 7 PM. No Field Scan

recording would occur from 8AM to 5:30PM, or from 7PM to 6AM.

6. After setting Start/Stop times to deﬁne Field Scan block "A" and/or

"B", press OK, then press the UP or DOWN key to select "Interval"

and press OK (Step 6). The Field Scan "Interval" setting lets you

control how often a photo or video clip is recorded during the block(s)

of time you deﬁned with the Start and Stop settings. Your options are

60 minutes, 30 minutes, 15 minutes, 5 minutes (this is the default), or

1 minute (still photo mode only). Use the UP/DOWN keys to select

your preference, then press OK to save it (Step 7). Note that for videos,

"Interval" is independent of the Length of each video recording-it’s

how often videos are recorded, not how long each one lasts.

7. Here’s an example of how the camera would operate, based on the

following Field Scan settings:

Field Scan: On

Field Scan A:

[Start]: 6:00

[Stop]: 8:00

Field Scan B:

[Start]: 17:30

[Stop]: 19:00

Interval: 15M

These settings would cause the camera to capture a photo (or video,

if the camera is set to that mode) once every 15 minutes, beginning

at 6 AM, until the Field Scan "A" recording block stops at 8:00 AM.

Later that day, the camera would again take a photo or video every 15

minutes between 5:30 PM and 7:00 PM (during Field Scan time block

"B"). The next day, the camera would again record an image or video

once every 15 minutes between 6:00 and 8:00 AM, and between

18

5:30 and 7:00 PM. No Field Scan recording would occur from 8AM

to 5:30PM, or from 7PM to 6AM. Remember, Field Scan recording

is independent of normal triggers due to animal activity–even if no

animals enter the IR sensor coverage zone, an image or video will still

be captured every 15 minutes during the block(s) of time. If an animal

triggers the camera “in between” the 15 minute intervals, it will be

recorded, same as it would if you had setup the camera with Field Scan

turned Off. Note: Field Scan settings of frequent intervals and/or

long periods between start and stop time can reduce battery life.

(Step 1)-set Field

Scan Mode to “On”

(Step 2)-select Field

Scan "A" (press OK)

(Step 3)-set Field

Scan "A" Stop & Start

(Step 4) (opt)-select Field

Scan "B" (press OK)

(Step 5) (opt)-set Field

Scan "B" Stop & Start

Steps 4 & 5 are

optional (only

required if you want

to set up a second

block of Field Scan

recording with

different stop and

start times)

(Step 6)-select Field

Scan "Interval"

(Step 7)-set Field

Scan Interval

Note: the Interval

Setting sets the

timing between each

image for both Field

Scan "A" and "B"

recording blocks.

19

Parameter

Settings

(Bold=default)

Description

Mode

Camera or Video

Selects whether still photos or video

clips are captured when the camera

is triggered.

Image Size

(only aects still

photos)

3M Pixel,

5M Pixel,

12M Pixel

Selects resolution for still photos from

3 to 12 megapixels. Higher resolution

produces better quality photos, but

creates larger ﬁles that take up more

of the SD card capacity (ﬁlls up

faster). 5M is a good compromise

between quality and ﬁle size.

Capture

Number

(only aects still

photos)

1 Photo,

2 Photo,

3 Photo

Selects how many photos are taken

in sequence per trigger in Camera

mode. Please also refer to the Interval

parameter.

Video Size

(only aects

video clips)

320x240,

640x480,

1280x720

Selects video resolution (in pixels per

frame). Higher resolution produces

better quality videos, but creates

larger ﬁles that take up more of the

SD card capacity (ﬁlls up faster).

640x480 is VGA video in standard

4:3 format, 1280x720 is widescreen

16:9 HD format.

Video Length

(only aects

video clips)

10S (second)

default, with 60S

to 5S possible

range

Sets length per captured video

clip. Settings begin with 10 second

default when parameter is ﬁrst

selected. After stepping down to

5S, video length settings start over

at 60S.

The SETUP Menu – Parameters and Settings

20

Parameter

Settings

(Bold=default)

Description

Interval

10S (second)

default, with a

60M (minute)

to1S (second)

range of settings

available.

(60M-1M are set

in one minute

increments,

59S-1S are set

in one second

increments)

Selects the length of time that the

camera will “wait” until it responds

to any additional triggers from the

PIR after an animal is ﬁrst detected

and remains within the sensor’s

range. During this user set “ignore

triggers” interval, the camera will not

capture photos/videos. This prevents

the card from ﬁlling up with too

many redundant images. Settings

begin with 10 second default when

parameter is ﬁrst selected. Note: after

setting down past “1S”, settings start

over at “60M”.

Sensor Level Low, Normal,

High, Auto

Selects the sensitivity of the PIR

sensor. The “High” setting will make

the camera more sensitive to infrared

(heat) and more easily triggered by

motion, and the “Low” setting makes

it less sensitive to heat and motion.

The High setting can be useful when

the ambient temperature is warm

(making it more difﬁcult for the sensor

to detect animals), and the Low

setting may help in cold weather if

the camera is being triggered too

often by anything warmer than the

surroundings. “Normal” is for average

or moderate conditions. The default

“Auto” setting will allow the camera

to determine the best setting based

on its current operating temperature.

This is an ideal setting if the weather

is expected to change signiﬁcantly

during the period the camera will be

used.

La page est en cours de chargement...

Bushnell NatureView Cam HD Essential 119739 Manuel utilisateur

Bushnell NatureView Cam HD Essential 119739 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents