Summit Commercial SBC635MBI7NKSSTB Manuel utilisateur
- Catégorie
- Frigos
- Taper
- Manuel utilisateur
Ce manuel convient également à
BEER DISPENSER
DISTRIBUTEUR de BIÈRE
Model / Modèle SBC635M
Use and Care Guide
Mode d’emploi
Felix Storch, Inc.
770 Garrison Avenue
Bronx, NY 10474
www.summitappliance.com
BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND
OPERATING INSTRUCTIONS.
Keep proof of original sales date (such as your sales slip) with this manual to
establish the warranty period.
Write the Serial Number below. You’ll find it on a plate located either on the back
of the appliance or on an interior wall.
AVANT UTILISATION, S'IL VOUS PLAÎT LIRE ET SUIVRE LES RÈGLES DE
SÉCURITÉ ET INSTRUCTIONS D'UTILISATION.
Conserver une preuve de la date d'achat d'origine (comme votre ticket de
caisse) avec ce manuel pour établir la période de garantie.
Écrire numéro de série ici. Vous le trouverez sur une plaque située soit sur
l’arrière de l'appareil ou sur un mur intérieur.
__________________________________________________
1
TABLE OF CONTENTS
Important Safeguards .................................................................................. 2 – 4
Location of Parts ................................................................................................ 5
Before Using for the First Time ........................................................................ 5
Placement and Installation ......................................................................... 6 - 10
Choosing the right place ............................................................................ 6
Installation ................................................................................................. 6
Applications ............................................................................................... 6
Connecting to power supply ...................................................................... 6
Reversing the door swing .......................................................................... 7
Installation of accessories ................................................................. 8 – 10
Operation .................................................................................................. 11 – 13
Control panel ........................................................................................... 11
Setting the temperature ........................................................................... 11
Switching between Celsius and Fahrenheit ............................................. 11
‘Rapid cooling’ function ........................................................................... 11
Automatic defrosting ............................................................................... 12
Error prompts .......................................................................................... 12
Normal functioning .................................................................................. 12
Dispensing beer .............................................................................. 12 – 13
Understanding beer temperature ............................................................ 13
Beer serving tips ..................................................................................... 13
Maintenance of the Beer Dispenser ............................................................... 14
Cleaning .................................................................................................. 14
Out of service .......................................................................................... 14
Transporting the unit ............................................................................... 14
Specifications of beer kegs ..................................................................... 14
Disposing of a Worn-Out Appliance ............................................................... 15
Draft Beer Troubleshooting .................................................................... 16 – 17
General Troubleshooting ................................................................................ 18
Limited Warranty .............................................................................................. 19
French version of this manual ................................................................. 20 - 39
2
IMPORTANT SAFEGUARDS
WARNING!
To reduce the risk of fire, electric shock or injury when using this
appliance, follow these basic precautions:
1. Read all instructions before using the appliance.
2. The appliance must be correctly connected to the power supply.
3. Immediately replace worn power cords, loose plugs and faulty power outlets.
4. Do not operate your appliance in the presence of explosive fumes.
5. Disconnect the appliance from the power supply before cleaning or repairing it.
Only a qualified technician should repair it.
6. Never stand on top of or inside this appliance, or swing on the door
7. To reduce likelihood of injury,
. Avoid
putting weight on top of the appliance.
do not let children play with this appliance
8. Do not operate the valve control unless the cylinder is completely installed and
connected.
.
9. Do not attempt to repair or replace any part unless this is recommended in this
Use and Care Guide. Leave other service matters to qualified technical
personnel.
10. Keep packing materials away from children as they could become a choking
hazard.
11. Do not spray or flush the beer dispenser with water, and avoid keeping it in a
damp place since this could damage the electrical insulation.
DANGER! Risk of child entrapment!
Child entrapment and suffocation are not problems of the past. Junked or
abandoned appliances are still dangerous, even if they will "just sit at the
curb for a few days."
Before discarding your old appliance:
• Take off the door.
• Leave the shelves in place so that children may not easily climb
inside.
• This appliance is CFC- and HFC-free and contains small quantities of
Isobutane (R600a) which is environmentally friendly, but flammable. It does
not damage the ozone layer, nor does it increase the greenhouse effect. Care
must be taken during transportation and setting up of the appliance that no
parts of the cooling system are damaged. Leaking coolant can ignite and may
damage the eyes.
In the event of any damage:
- Avoid open flames and anything that creates a spark,
- Disconnect from the electrical power line,
3
- Air the room in which the appliance is located for several minutes, and
- Contact the Service Department for advice.
• The more coolant there is in an appliance, the larger the room it should be
installed in. In the event of a leakage, if the appliance is in a small room, there
is the danger of combustible gases building up. For every ounce of coolant at
least 325 cubic feet of room space is required. The amount of coolant in the
appliance is stated on the data plate on the back of the appliance. It is
hazardous for anyone other than an Authorized Service Person to carry out
servicing or repairs to this appliance.
• Take serious care when handling, moving, and using the appliance to avoid
either damaging the refrigerant tubing or increasing the risk of a leak.
• Replacing component parts and servicing shall be done by factory authorized
service personnel so as to minimize the risk of possible ignition due to
incorrect parts or improper service.
SAFETY PRECAUTIONS REGARDING ELECTRICAL MATTERS
1. Do not pull on the power cord when unplugging the machine. Grasp the plug
firmly and pull it straight out of the socket. Do not pull the plug with wet hands.
2. Keep the power cord at the back of the appliance to avoid tripping accidents or
damage to the cord.
3. If the power cord is damaged or frayed, it must be replaced by a qualified
service professional.
4. Use only a standard three-hole grounded power socket rated above 10A. The
socket should not be shared with other appliances.
5. Be sure the plug fits firmly into the socket and that the socket is grounded.
6. The use of an extension cord is NOT recommended.
7. The beer dispenser requires an AC power supply of 110~120V/60Hz and pulls
a current of over 10A. The fuse or circuit breaker should be rated at 15A.
8. If the leakage of a combustible gas is detected, turn off the gas valve and
open the doors and windows. To reduce the risk of fire caused by a spark, do
not pull out the plug of the beer dispenser or of any other electrical device.
SAFETY PRECAUTIONS REGARDING CO
2
(CARBON DIOXIDE) GAS
Always connect the CO
2
cylinder to a regulator! Failure to do so may cause an
explosion resulting in possible injury or death when the cylinder valve is opened.
Never connect the CO
2
cylinder directly to the product container.
Always keep CO
2
cylinders away from heat. Store extra cylinders in a cool place
(preferably below 70°F). Securely fasten cylinders with a chain in an upright
position when storing.
Never drop or throw a CO
2
cylinder.
Always check the D.O.T. (Department of Transportation) test date on the
cylinder neck before installation. If it has been more than 5 years, do not use.
Return the cylinder to your gas supplier.
4
Never connect a product container unless there are at least two safety devices in
the pressure system: one on the CO
2
regulator and the other on the product
container or in the pressurized gas line.
The recommended pressure for the CO
2
system is 8-10 lbs.
SAVE THESE INSTRUCTIONS
Tips to save energy and maintain optimum performance:
When positioning this unit: If used freestanding, allow 4 inches
of clearance on top, at the sides and in the rear for sufficient
airflow.
Do not use under a bar or counter.
5
LOCATION OF PARTS
BEFORE USING FOR THE FIRST TIME
The SBC635M is designed for dispensing beer only, and is not recommended for
storing perishable foods such as meats or dairy products
.
Before connecting the appliance to the power supply, leave it standing for 2 to 3
hours
Clean the appliance thoroughly, especially the interior. (See Maintenance of the
Beer Dispenser.)
. This allows the refrigerant to drain back into the compressor and reduces
the risk of malfunctions in the cooling system caused by shipping.
Proper grounding must be ensured to reduce the risk of shock
and fire. Do not cut or remove the grounding plug!
Try not to open the door too often, especially when the weather is hot and humid.
Once you open the door, try to close it as soon as possible.
TIPS FOR SAVING ENERGY
If possible, disconnect the power before changing a keg of beer.
Keep the unit out of direct sunlight.
Periodically, check that the beer dispenser seals well and that none of the
contents prevent the door from closing.
Beer tower assembly
Upper cover guardrail
Drip tray
Display and control
panel
Evaporator
Ball valve
Beer keg
Door
Bottom pad
Caster
Top cover
Cabinet
CO
2
regulator valve
CO
2
gas cylinder
CO
2
tank supporter
Control board device
Compressor
chamber cover
6
PLACEMENT AND INSTALLATION
To ensure that your beer dispenser works at the maximum efficiency it was
designed for, install it in a location where there are proper air circulation and
electrical connections.
Choosing the Right Place
Choose a location where the beer dispenser will be away from any heat sources
and will not be exposed to direct sunlight.
Remove all packing materials before using the beer dispenser.
Place the machine on a smooth, flat and sturdy surface.
Your appliance is not designed to operate in enclosed spaces. When placing
your unit, make sure you allow at least 4” of clearance at the sides, rear and top
to allow for adequate airflow.
Installation
The SBC635M beer dispenser meets UL Standard 250 and is suitable for
residential use.
Applications
Connect this appliance to a 3-prong power supply socket (which has a ground
terminal).
Connecting to Power Supply
If you only have a two-prong outlet, have it replaced by a qualified
technician with an outlet that meets the local codes
DO NOT USE AN EXTENSION CORD
.
Required nominal voltage and frequency are indicated on the rating plate. The
connection to the power supply and grounding has to be made according to
current standards and regulations. The appliance resists temporary voltage
fluctuations with a tolerance of ±10%.
Once connected, allow the appliance to operate empty for two to three hours
before putting a beer keg inside.
7
Reversing the Door Swing
Figure 1 (Default position) Figure 2 (After door reversal)
1. Upper hinge cover 6. Screws
2. Screws 7. Hole cover
3. Upper hinge 8. Cabinet
4. Door 9. Pin cap
5. Lower door hinge
The beer dispenser can be opened from either the right side or the left. By default, the
door hinge is on the right side. If you prefer it on the left, please follow these instructions:
Note: All of the parts that are removed must be kept for the reinstallation of the door.
1. Remove the three screws (6) holding lower door hinge (5). Keep hinge for later use.
2. Remove the door from the upper hinge (3), and keep the padded surface upward to
prevent scratching.
3. Remove the upper hinge cover (1), remove the two screws (2), remove the upper
hinge (3) and keep it for later use.
4. Remove the hole cover (7) and transfer it to the same location on the opposite side.
5. Insert the lower door hinge (5) into the left side, fixing the hinge into place by
tightening all the screws (6).
6. Remove the pin cap (9) from the left side of the upper door frame and then transfer it
to the same location on the opposite side.
7. Set the door on the lower door hinge (5), keep the door level, then fix the upper hinge
(3) to the body (8) by the screws (2).
8. Put on the upper hinge cover (1).
8
Installation of Accessories
Diagram of overall structure
Installation components
Installation steps
1. Install universal wheels:
Lock braking guidelines for universal wheels
with foot brakes (See Figure 1):
Install the two universal wheel washers at the front of the cabinet base, and
then install two universal wheels without foot brakes. Next, install the two
universal wheels with foot brakes at the back of the cabinet base. Once
Beer keg handle
Soft red CO
2
tube
Beer keg
Tap handle
Draft beer tap
CO
2
hose clamp
CO
2
tank bracket and bolt
Drip tray
Drip tray assembly
9
installed these rear wheels will keep the unit from moving if you step on the
foot brakes (See Figure 2):
2. Install the beer tower assembly and the mixed ball valve:
a) Plug the beer tower assembly into the top cover of the beer dispenser:
3.0” tower: This does not require a tower
buckle. Put beer tower directly over the
hole at the top of the beer dispenser’s
upper surface. Fix the beer tower assem-
bly with screws directly on the upper sur-
face of the beer dispenser. (See Fig. 3).
2.5” tower: This requires the tower buckle.
Place the beer tower at the hole in the upper surface of the beer dispenser
at an inclination of 60°, and rotate 60° clockwise along the card slot. Be
sure the tap is facing toward the front of the machine. Attach the beer tower
with washers (See Figure 4).
b) Take out the accessories of the mixed ball valve. Attach the transparent
hose to the beer outlet of the mixed ball valve (See Figure 5).
3. Install CO
2
gas cylinder and CO
2
regulator valve:
a) Fix the two CO
2
hose clamps on the red
CO
2
tube (See Figure 6).
b) Connect the ends of the red CO
2
tube
respectively to the CO
2
intake port of the
mixed ball valve and the round outlet of
the CO
2
regulator valve. Lock these
connections firmly with the two clamps on
the red CO
2
tube (See Figure 7).
c) Using the wrench, tighten the CO
2
regulator table valve with the hex nut port
to the gas outlet of the CO
2
tank (See Figure 8).
CO
2
regulator
valve
Safety switch
Red CO2 tube
Bracket and retainer
of CO
2
tank
Regulating
table
CO
2
gas
cylinder
10
d) Place the CO
2
tank and CO
2
regulator valve component into the
cabinet and fix the CO
2
tank
with tank bracket and bolt (See
Figure 8).
4. Install the beer keg:
Place the beer keg into the cabinet and
firmly connect the keg’s opening to the
connection port of the mixed ball valve
(See Figure 10).
Note: To place a keg into the cabinet,
use the keg handle to move the keg
to the front of the open beer
dispenser, then carefully tip the keg
so that the raised bottom edge contacts the edge of the cabinet. Finally, lift
the keg handle to raise the keg to the level of the floor of the cabinet and
push the keg into place.
5. Install tap handle and beer tap:
Screw the tap handle clockwise into the beer tap to make a firm connection.
Then connect the tap to the beer tower components and tighten with a wrench
(See Figure 9).
6. Install upper cover guardrail and drip tray:
Set the upper cover guardrail and drip tray on top of the beer dispenser (See
Figure 10).
Notes:
• When replacing the beer keg, first turn off the safety switch on the CO
2
regulator valve and remove the mixed ball valve to take out the keg.
• When replacing the CO
2
gas cylinder, remember to turn off the main
switch of the CO
2
gas cylinder and the safety switch on the CO
2
regulator
valve. Afterwards, use a wrench to loosen the hexagonal nut port
connecting the CO
2
regulator valve with the CO
2
tank. Then, using a
wrench, remove the fixed bolt of the CO
2
tank to take out the CO
2
tank.
• During the installation process, be sure that all parts are connected tightly
and that there are no gas leaks.
• When connecting the hose to the connection port, you can dip the ends
into warm water to make the connection easier.
• If the high-pressure compressed gas in the CO
2
tank is not handled
properly, it could be dangerous:
a. Make a note of the D.O.T. testing date on the cylinder neck before
installation. If it is more than 5 years old, don’t use the product. Return
it to the gas supplier.
b. Keep gas cylinder away from heat sources. Unused cylinders should
be placed upright in a cool, ventilated place (preferably at 70°F).
11
OPERATION
The control panel is located just above the door, and looks like this:
Control Panel
Adjust the DOWN or UP button on the control panel until the display module
shows the desired temperature.
Setting the Temperature
The display module shows the set temperature, and the temperature-controlled
range varies from 32 to 50°F (0 to 10°C).
The display module shows 5°C at the initial power up. Each press of the DOWN
or UP button decreases or increases the temperature displayed by 1°C (1°F).
The optimal temperature for the storage and distribution of beer is 34 - 38°F (1.1
to 3.3°C.
You can switch between a Celsius and Fahrenheit temperature display by
pressing the °F/°C button. When the displayed temperature is in Celsius, the “°C”
symbol will be illuminated; with a Fahrenheit display, “°F” will be illuminated.
Switching between Celsius and Fahrenheit
Press the Deep Chill button to enter the Rapid Cooling state. The “rapid cooling”
icon on the display module will light and the temperature display will read “00”.
After entering the Rapid Cooling mode, the appliance will work continuously for
24 hours and the icon will remain lit. After that time, the icon will turn off and the
appliance will return to its former state.
‘Rapid Cooling’ Function
You can cancel the Rapid Cooling mode any time during the 24 hour period by
simply pressing the Deep Chill button again.
Note: The Rapid Cooling function is normally used only for cooling the first keg of
beer in the appliance, when that keg is to be used as soon as possible. To
prevent over-cooling the beer, do not use Rapid Cooling for succeeding kegs.
DOWN: Lowers UP: Raises Display module Fahrenheit/Celsius Rapid
temperature temperature switching cooling
12
There is usually no need to defrost the beer dispenser because the ice deposited
on the inner back wall is automatically defrosted. Ice deposits on the inner back
wall during compressor operation. Later on, when the compressor is not
operating, the ice defrosts and water drains through the outlet in the inner back
wall into the drain pan situated above the compressor where it evaporates. If you
see water building up in the rear of the unit, check that the drain trough is not
clogged. Use a pipe cleaner or a piece of flexible wire. During extremely hot and
humid weather, some ice may build up. If necessary, remove contents of the
beer dispenser, unplug the unit and allow defrosting. A hair dryer may facilitate
the process.
Automatic Defrosting
When the following prompts appear in the display module, there is a failure in the
appliance. Although one of the fault conditions occurs, the beer dispenser may
still work. However, you should contact our Service Department as soon as
possible to obtain advice on handling the situation.
Error Prompts
Prompt
E1
E4
E7
Fault
Temperature sensor
failure in the
refrigerated zone
Defrosting sensor
failure in the refrigerator
compartment
Ambient
temperature
sensor fault
Note: When two or more sensors fail simultaneously, all fault codes will display
alternately on the display module. If the ambient temperature and defrost
sensors fail, any key may be pressed. The temperature is adjustable. The
fault display will be restored after 15 seconds.
• If there is a sound of rushing water when the machine is in use, the noise is
caused by the refrigerant flowing in the cooling pipes and running through the
compressor. This is a normal phenomenon.
Normal Functioning
• The beer dispenser has no heating function. When the temperature is set
higher than the ambient temperature, the machine will not run.
Follow these steps to dispense beer:
Dispensing Beer
1. Make sure the beer dispenser is plugged in properly to a 120V, 60Hz, 15 amp
grounded AC outlet.
2. Place the drip tray under the beer tap.
3. Open the beer faucet by pulling the tap towards you quickly and completely to
dispense the beer.
4. Increase the pressure if the beer runs too slowly. At the correct pressure and
temperature, a 10-oz glass should be filled in 4 seconds.
13
5. Hold the glass steady at a 45° angle. When it is 2/3 full, start straightening the
glass. Proper foam should be a tight, creamy head and the collar on an
average glass should be 3/4" to 1" high.
Note: It is normal to see condensation forming on the tap. It is caused by the
difference in temperature between the cold beer and the inner surfaces of the
tap when beer is flowing through the line.
The recommended temperature for serving chilled beer is between 38° and 43°F.
To maintain this temperature in average room conditions of 70°F, set the
thermostat accordingly.
Understanding Beer Temperature
Notes: During the summertime when temperatures are warmer, we recommend
that you adjust the control to a cooler setting. Selecting and maintaining the
proper temperature inside the refrigerator cabinet is necessary for maintaining
the flavor and freshness of beer. Excessively cold or warm temperatures
inside the refrigerator cabinet may cause a loss of flavor.
The best temperature for storing a keg is approximately 38°F.
Sour beer is produced as a result of secondary fermentation above 45°F.
The following tips will help you serve the perfect beer. To serve beer from the
tap similar to the way it left the vat, check the following:
Beer Serving Tips
• Cleanliness (see Maintenance of the Beer Dispenser)
• Temperature (see Setting the Temperature and Understanding Beer
Temperature)
• Pressure (The recommended pressure for the CO
2
system is 8-10 lbs.)
• Use only CO
2
gas
14
MAINTENANCE OF THE BEER DISPENSER
To optimize cooling and to save energy at the same time, dust the back of the
beer dispenser periodically.
Cleaning
The interior should be cleaned regularly. Use a soft towel or sponge that has
been dampened in a solution of mild detergent. Rinse with clean water and dry
with a cloth. Leave the door open for a while to allow the unit to dry thoroughly
before turning the power back on.
Do not use a hard brush, steel wool, wire brush, or abrasives such as toothpaste,
or organic solvents like alcohol or acetone to clean the beer dispenser.
When cleaning or rinsing the unit, be careful not to let the control panel or any
electrical components become wet.
If the machine will be out of service for more than three weeks, unplug it and
clean and dry it thoroughly. Allow the door to remain open slightly to prevent the
buildup of mold and odors.
Out of Service
Firmly fix any loose items inside the beer dispenser with tape. Tape the door shut
so it will not open during transportation.
Transporting the Unit
Loosen the two foot brakes before moving the unit.
Keg sizes that can be used in your beer dispenser:
Specifications of Beer Kegs
1/2 barrel 59 liters 15.5 gals. 1,984 oz. 164 / 12-oz. Glass
1/4 barrel 30 liters 7.8 gals. 992 oz. 82 / 12-oz. Glass
1/6 barrel 20 liters 5.2 gals. 661 oz. 55 / 12-oz. Glass
1/8 barrel 15 liters 4.0 gals. 496 oz. 41 / 12-oz. Glass
Note: Our beer dispenser accepts almost all brand name 1/2 kegs. However,
Coors’ kegs do not fit in our unit.
15
DISPOSING OF A WORN-OUT APPLIANCE
• When your appliance finally wears out, dispose of it.
• Before you dispose of an old appliance: Take the door or doors off but leave
any shelves or drawers in place so that children cannot easily climb inside.
• The refrigerating system of the appliance is filled with refrigerant and insulating
substances that should be recycled separately. Either have a licensed
appliance repair company or dealer remove the appliance or call your local
recycling office for the appropriate disposal information.
• For the sake of environmental protection, when moving the appliance, be
careful not to damage the rear wall (the condenser unit or the tubes) or any
part of the refrigeration system inside the appliance.
• This beer dispenser is 100% CFC-free, but the coolant is under pressure and
inflammable, and puncturing the sealed system could be dangerous. The
coolant used in the sealed system is non-toxic.
• Many older appliances may contain refrigerants that are harmful to the
environment, and should be recycled by a lawfully licensed company.
16
DRAFT BEER TROUBLESHOOTING
Problem
Cause
Correction
Beer is cloudy:
The beer in the
glass appears
hazy and not clear.
Excessively low
temperatures
may cause
hazy or cloudy
beer,
particularly
when the beer
lies in the cold
coil for long
periods of time.
Drain a few ounces before drinking.
Raise the temperature setting of the unit.
Glasses may
not have been
cleaned
properly.
Do not wash beer glasses together with glasses
that have contained milk or any other fatty
substance. An excessive amount of germicide
build-up may also leave a fatty film, which will
cause beer to go flat.
It is preferable to steam and sterilize glasses
where health laws permit.
Wash glasses thoroughly with a good detergent
to remove all fatty substances (e.g., lipstick).
Do not use soap.
Do not wipe the glasses dry. Permit glasses to
air-dry by placing them on a wire rack or
corrugated metal sheet.
Rinse the glasses in fresh cold water just before
serving beer. It is best to serve beer in a wet
glass.
Improper
drawing of beer
into glass
Open the faucet quickly and completely; proper
foam should be a tight creamy head. The collar
on the average glass should be ¾" to 1" high.
Beer drawn without a head has the appearance
of being flat.
Not enough
pressure
Increase the pressure if beer runs too slowly.
The correct flow should fill a 10-oz glass in 4
seconds (approx. 8 oz of liquid). Check the
pressure source to determine whether there are
obstructions in the air line. Replace a sluggish
air source or the CO
2
regulator and gauge. The
tank pressure must always be higher than the
pressure used on the keg. Always apply
pressure to the keg before drawing beer.
17
Beer has off taste:
Often bitter and
bite-y; sometimes
completely lacking
flavor and zest. It
may also have an
oily or foul odor
which may carry
an unpleasant
taste.
Improper
cleaning of the
tap
Brush and clean the tap properly. It should be
scoured using a detergent, then rinsed clean.
Contaminated
air line
Beer tube should be examined. If contaminated,
it should be replaced.
Condensation is
forming on the tap.
It is normal to
see conden-
sation forming
on the tap. It is
caused by a
difference in
temperature
between the
cold beer and
the surfaces of
the tap when
beer is flowing
through the line.
Beer that is left
in the tap is not
cooled by the
beer dispenser.
After a period of non-use, a few ounces should
be drained before drinking.
18
GENERAL TROUBLESHOOTING
If there is a problem with the beer dispenser itself, see if you can find it listed in
the chart below. You may be able to save yourself the cost of a service visit.
Problem
Possible Cause
The beer dispenser doesn’t
work.
Power supply not firmly connected.
Supplied voltage is too low.
Tripped circuit breaker or blown fuse.
The machine switches on
and off frequently.
Indoor temperature is higher than usual.
Machine door is opened frequently.
Door is not completely closed.
Temperature control is not set correctly.
Door cannot be closed
properly.
Beer keg not properly placed.
Beer dispenser is not level.
Door was reversed and re-installed incorrectly.
Metal plate or beer kegs are out of place.
Noise Rushing noise may be the sound of refrigerant
flow, which is normal.
As each cycle ends, the gurgle of refrigerant flow
may be heard.
Contraction and expansion of inner wall may cause
pops and crackles.
19
LIMITED WARRANTY
Within the 48 contiguous United States, for one year from the date of purchase, when this appliance is
operated and maintained according to instructions attached to or furnished with the product, warrantor will
pay for factory-specified parts and repair labor to correct defects in materials or workmanship. Service must
be provided by a designated service company. Outside the 48 states, all parts are warranted for one year
from manufacturing defects. Plastic parts, shelves and cabinets are warranted to be manufactured to
commercially acceptable standards, and are not covered from damage during handling or breakage.
ONE-YEAR LIMITED WARRANTY
1. The compressor is covered for 5 years.
5-YEAR COMPRESSOR WARRANTY
2. Replacement does not include labor.
ITEMS WARRANTOR WILL NOT PAY FOR:
1. Service calls to correct the installation of your appliance, to instruct you how to use your appliance, to
replace or repair fuses or to correct wiring or plumbing.
2. Service calls to repair or replace appliance light bulbs or broken shelves. Consumable parts (such as
filters) are excluded from warranty coverage.
3. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation,
installation not in accordance with electrical or plumbing codes, or use of products not approved by
warrantor.
4. Replacement parts or repair labor costs for units operated outside the United States.
5. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
6. Expenses for travel and transportation for product service in remote locations.
7. The removal and reinstallation of your appliance if it is installed in an inaccessible location or is not
installed in accordance with published installation instructions.
DISCLAIMER OF IMPLIED WARRANTIES;
CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE
PRODUCT REPAIR AS PROVIDED HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR.
WARRANTOR SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME
STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF MERCHANTABILITY
OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY
GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY
FROM STATE TO STATE.
LIMITATION OF REMEDIES
FELIX STORCH, INC.
770 Garrison Avenue
Bronx, NY 10474
Phone: (718) 893-3900
Fax: (844) 478-8799
www.summitappliance.com
For parts and accessory ordering,
troubleshooting and helpful hints, visit:
www.summitapplianceparts.com
WARNING! This product may contain chemicals known to the state of California
to cause cancer or birth defects or other reproductive harm. For more information,
visit: www.summitappliance.com/prop65
Chemicals known by the manufacturer to be present in this product in concentrations
higher than threshold limits: NONE.
Revised March 2015
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
Summit Commercial SBC635MBI7NKSSTB Manuel utilisateur
- Catégorie
- Frigos
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
Documents connexes
Autres documents
-
Summit SBC635MBIIF Manual SBC635MBI
-
-
Kenmore 25591589010 Le manuel du propriétaire
-
Summit SBC635MBI7TWIN Manuel utilisateur
-
Philips HD3620/20 Manuel utilisateur
-
Philips HD3620 Manuel utilisateur
-
Philips HD3720/25R1 Manuel utilisateur
-
Philips hd 3620 perfect draft Manuel utilisateur