Valor 1800JN/JP Le manuel du propriétaire

4004995-12

This appliance may be installed in an after-

market permanently located, manufactured

(mobile) home where not prohibited by local

codes.

This appliance is only for use with the type

of gas indicated on the rating plate. This

appliance is not convertible for use with

other gases, unless a certiﬁ ed kit is used.

HOT GLASS WILL

CAUSE BURNS.

DO NOT TOUCH GLASS

UNTIL COOLED.

NEVER ALLOW CHILDREN

TO TOUCH GLASS.

DANGER

!

A barrier designed to reduce the risk of burns from the hot

viewing glass is provided with this appliance and shall be

installed for the protection of children and other at-risk

individuals.

Ce guide est disponible en français sur demande.

This appliance is a domestic room-heating

appliance. It must not be used for any other

purposes such as drying clothes, etc.

This appliance is suitable for installation in

a bedroom or bed sitting room.

INSTALLER

Leave this manual

with the appliance.

CONSUMER

Retain this manual

for future reference.

Please read this manual

BEFORE installing and

operating this appliance.

INSTALLATION & OWNER’S MANUAL

— Do not store or use gasoline or other

ﬂ ammable vapors and liquids in the

vicinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

▪ Do not try to light any appliance.

▪ Do not touch any electrical switch; do

not use any phone in your building.

▪ Leave the building immediately.

▪ Immediately call your gas supplier from

a neighbor’s phone. Follow the gas

supplier’s instructions.

▪ If you cannot reach your gas supplier,

call the ﬁ re department.

— Installation and service must be

performed by a qualiﬁ ed installer,

service agency or the gas supplier.

! WARNING

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly

could result in serious injury, death, or

property damage.

Direct Vent Zero Clearance Gas Fireplaces

1800JN (natural gas) & 1800JP (propane gas)

This manual contains instructions to install the

ENGINE ONLY. A trim kit is REQUIRED to

complete the installation. A barrier screen is

provided with the trim kit. Refer to the manual

supplied with the trim for installation.

L3 Series

2

Table of Contents

Speciﬁ cations ................................................20

Overview.........................................................21

Dimensions & Location .................................22

Mantel & Hearth Clearances .........................23

Framing Requirements ................................. 25

Venting ............................................................ 28

Co-axial Venting............................................. 29

Installation Planning ..................................... 33

Plan Wall Finish ....................................................... 34

Installation ......................................................35

Unpack Appliance ....................................................35

Install Standoﬀ s .......................................................35

Remove Window ..................................................... 36

Complete Installation of optional LDK HeatShift

Duct Kit (if used) ...................................................36

Fit optional LDK HeatShift Duct Kit’s take-oﬀ collars

to appliance (if used) ............................................ 36

Fit Appliance into Framing ....................................... 36

Install Electrical Wiring (for optional accessories) ...37

Set-up Gas Supply .................................................. 38

Install Liners ............................................................ 40

Install Driftwood Kit 1800DWK ................................ 42

Install Decorative Glass Murano 1800DGM ............45

Install Split Wood Kit 1800SWK .............................. 46

Reﬁ t Window ...........................................................51

Install Remote Battery and Wall Switch Kit

RBWSK (required) ................................................52

Synchronize Remote Control ................................... 54

Check Operation ...................................................... 55

Set Aeration (if necessary) ......................................55

Install Plinth Support Bracket .................................. 56

Install Trim and Barrier Screen ................................56

Install Remote Control Handset Wall Holder ...........56

Wiring Diagram .............................................. 57

Approved Venting Components ...................58

Commonwealth of Massachusetts...............60

Warranty .........................................................62

Spare Parts.....................................................63

Massachusetts: The piping and ﬁ nal

gas connection must be performed by a

licensed plumber or gas ﬁ tter in the State of

Massachusetts. Also, see Carbon Monoxide

Detector requirements on page 60.

Designed and Manufactured by / for Miles Industries Ltd.

190–2255 Dollarton Highway,

North Vancouver, BC, CANADA V7H 3B1

Tel. 604-984-3496 Fax 604-984-0246

www.valorﬁ replaces.com

FOR THE OWNER FOR THE QUALIFIED INSTALLER

The information contained in this installation manual

is believed to be correct at the time of printing. Miles

Industries Ltd. reserves the right to change or modify

any information or speciﬁ cations without notice.

Miles Industries Ltd. grants no warranty, implied or

stated, for the installation or maintenance of your

heater, and assumes no responsibility for any conse-

quential damage(s).

Warranty Card at the

back of this manual.

W

A

R

A

N

T

Y

P

R

O

G

R

A

M

W

A

R

A

N

T

Y

P

R

O

G

R

A

M

V

A

L

O

R

C

O

M

F

O

R

T

V

A

L

O

R

C

O

M

F

O

R

T

V

A

L

O

R

C

O

M

F

O

R

T

Safety and Your Fireplace ...............................3

Introduction ......................................................6

Locating Fireplace & Lighting Information Card ........ 6

Operating Your Fireplace for the First Time ............... 6

Operating Your Fireplace ................................ 7

Fireplace Control Devices ......................................... 7

How to Turn Your Fireplace ON ................................. 7

How to Turn Your Fireplace OFF (and pilot) ..............7

How to Ensure Your Fireplace Cannot

Be Turned ON Inadvertently ...................................7

Using the Remote Control ..............................8

Using the Wall Switch ...................................13

Kits & Accessories ........................................ 13

Lighting Instructions .....................................14

Maintaining Your Fireplace ........................... 15

Servicing Your Fireplace ..........................................15

Annual Inspection .................................................... 15

Cleaning Your Fireplace .......................................... 16

Checking Pilot and Burner Flames .......................... 18

Replacing Batteries ................................................. 19

Using Handset Wall Holder ...................................... 19

Warranty .........................................................62

3

Safety and Your Fireplace

SAFETY AND YOUR FIREPLACE

!

Children and adults should be alerted to the hazards

of high surface temperature and should stay away to

avoid burns or clothing ignition.

Young children should be carefully supervised

when they are in the same room as the appliance.

Toddlers, young children and others may be susceptible

to accidental contact burns. A physical barrier is

recommended if there are at-risk individuals in the

house. To restrict access to a ﬁ replace or stove, install

an adjustable safety gate to keep toddlers, young

children and other at-risk individuals out of the room

and away from hot surfaces.

Do not place furniture or any other combustible house-

hold objects within 36” of the ﬁ replace front.

Read and understand all instructions carefully before

starting the installation. Failure to follow these instal-

lation instructions may result in possible ﬁ re hazard and

will void the warranty.

Prior to the ﬁ rst ﬁ ring of the ﬁ replace, read the

Owner’s information section of this manual.

Do not use this appliance if any part has been under

water. Immediately, call a qualiﬁ ed service technician

to inspect the unit and to replace any part of the control

system and any gas control that has been under water.

This unit is not for use with solid fuel.

Installation and repair should be performed by a

qualiﬁ ed service person. The appliance and venting

system should be inspected before initial use and at

least annually by a professional service person. More

frequent cleaning may be required due to excessive lint

from carpeting, bedding, etc. It is imperative that the

unit’s control compartment, burner, and circulating air

passageways be kept clean to provide for adequate

combustion and ventilation air.

Always keep the appliance clear and free from

combustible materials, gasoline, and other ﬂ ammable

vapors and liquids.

Never obstruct the ﬂ ow of combustion and venti-

lation air. Keep the front of the appliance clear of all

obstacles and materials for servicing and proper opera-

tion.

Due to the high temperature, the appliance should be

located out of traﬃ c areas and away from furniture and

draperies.

Clothing or ﬂ ammable material should not be placed

on or near the appliance.

This unit must be used with a vent system as de-

scribed in this installation manual. No other vent sys-

tem or components may be used.

This gas ﬁ replace and vent assembly must be vented

directly to the outside and must never be attached to

a chimney serving a separate solid fuel burning appli-

ance. Each gas appliance must use a separate vent

system. Common vent systems are prohibited.

Inspect the external vent cap on a regular basis to

make sure that no debris, plants, trees, shrubs are inter-

fering with the air ﬂ ow.

Do not operate this appliance with the glass door

removed, cracked, or broken. Replacement of the

glass door should be performed by a licensed or qualiﬁ ed

service person. Do not strike or slam the glass door.

The glass door assembly shall only be replaced as

a complete unit, as supplied by the ﬁ replace manufac-

turer. No substitute material may be used.

A barrier designed to reduce the risk of burns from

the hot viewing glass is provided with this appliance and

shall be installed for the protection of children and

other at-risk individuals.

Do not use abrasive cleaners on the glass door assem-

bly. Do not attempt to clean the glass door when it is hot.

If the barrier becomes damaged, the barrier shall

be replaced with the manufacturer’s barrier for this

appliance.

Turn oﬀ the gas before servicing this appliance. It is

recommended that a qualiﬁ ed service technician per-

form an appliance check-up at the beginning of each

heating season.

Any safety screen, guard or barrier removed for

servicing the appliance, must be replaced prior to

operating the appliance.

Be careful not to put any decorating objects sensi-

tive to heat to close above or around the ﬁ replace as it

gets very hot when operating.

Do not use this heater as a temporary source of

heat during construction.

This appliance is a domestic room-heating appliance.

It must not be used for any other purposes such as dry-

ing clothes, etc.

The glass door assembly must be in place and sealed

before the unit can be placed into safe operation.

This product can potentially expose you to chemicals

including Benzene which are known to the State of

California to cause cancer and birth defects or other

reproductive harm. For more information go to

www.P65Warnings.ca.gov

WARNING:

4

Parts of your Valor Fireplace become

extremely hot while in operation.

The glass viewing window temperature

can exceed 500 F at full capacity.

Momentary contact with a hot glass

surface can cause a severe burn, even

if the ﬁ replace is operating at reduced

heating capacity.

The glass window will remain hot

for an extended period of time after

the ﬁ replace has been turned oﬀ .

Ensure that children are prevented from

touching the ﬁ replace during the cool

down period.

Toddlers and Young Children must

be closely supervised at all times

when they are in the same room as

the operating ﬁ replace. They lack full

awareness of danger and rely on your

protection. Toddlers, in particular, do

not have the motor skills and response

reﬂ exes to withdraw in the event of

accidental contact with a hot surface.

A physical barrier is strongly

recommended if there are young

children, or at-risk individuals in the house.

Install an approved after-market safety

gate to keep toddlers, young children and

other at-risk individuals a safe distance

from the ﬁ replace.

Keep the remote control handset out

of reach of children at all times. A wall

mount storage holster is provided with

your remote control handset.

Ensure that the ﬁ replace, including

the pilot light, is completely turned

oﬀ when children are present and close

supervision and safety barriers are not

available—see page 7 of this manual.

If the ﬁ replace is not going to be used

for the summer or any extended period

of time, remove the batteries from the

remote control handset and remote

battery box. It is recommended that

batteries are replaced annually in any

event—see page 19.

Read and carefully follow all safety warnings and

operating instructions contained in your owner’s manual

Replacement manuals are available by contacting the Valor Service Department

at 1-800-468-2567 or visit www.valorﬁ replaces.com.

Safety and Your Fireplace

!

FOLLOW THESE IMPORTANT CHILD SAFETY

PRECAUTIONS AND RECOMMENDATIONS

5

Front outlet

Side

outlet

This manual and particularly the preceeding and following pages contain very important information regarding

the safe operation of your ﬁ replace as well as maintenance instructions. Read carefully before operating your

ﬁ replace and pay special attention to the safety warnings.

A heating gas appliance does require safe handling. For this reason, we very strongly recommend children are not

allowed to touch the ﬁ replace or controls. Install a screen or barrier in front of the ﬁ replace to protect your children

against severe burns.

This appliance is designed and approved as a supplemental heater and provides the potential for most

energy conservation when used while attended. The use of an alternate primary heat source is advisable.

Do not put

furniture or other objects

in this space in front of

the replace:

36” (0.9 m)

Fireplace

Hearth

WARNING

HeatShift

Duct Kit:

Do not cover

or place items

in front of or

on top of

outlet(s)!

!

!WARNING

EXTREMELY HOT!!!

• Read the safety information on pages 3 and

4 of this manual before operating your gas

heater.

• Some parts of your ﬁ replace are extremely

hot, particularly the glass window.

• Do not let children touch the glass or any

parts of your ﬁ replace even after it is turned

oﬀ as it is still hot.

• Use the barrier screen provided with the trim

or a gate to reduce the risk of severe burns.

• Keep the remote control handset out of reach

of children.

• Hot wall surfaces! The wall directly above

the ﬁ replace is very hot when the ﬁ replace

heats. It is constructed of non-combustible

materials and although safe, it may reach

temperatures in excess of 200º F depending

on choice of trims or optional accessories. DO

NOT TOUCH! We recommend installing the

optional LDK HeatShift Duct Kit when hot

walls are a concern.

•

Some materials or items, although safe, may

discolor, shrink, warp, crack, peel, and so on

because of the heat produced by the ﬁ replace.

Avoid placing

candles, paintings, photos, and

other items

sensitive to heat

within 36 inches

(0.9 m) around the ﬁ replace.

•

Solid wood ﬂ ooring in front of the ﬁ replace (if

allowed) may shrink during the heating season

due to heat.

SAFETY AND YOUR FIREPLACE

!

6

WARNING

DO NOT ATTEMPT TO TOUCH THE DATA CARD

WHILE THE FIREPLACE IS STILL HOT! Let the

ﬁ replace cool ﬁ rst before touching it.

!

Operating Your Fireplace for the First

Time

When operating your new ﬁ replace for the ﬁ rst time,

some vapors may be released due to the burning of

curing compounds used in the manufacture of the

appliance. They may cause a slight odor and could

cause the ﬂ ames to be the full height of the ﬁ rebox, or

even slightly higher, for the ﬁ rst few hours of operation.

It is also possible that these vapors could set oﬀ any

smoke detection alarms in the immediate vicinity.

These vapors are quite normal on new appliances. We

recommend opening a window to vent the room. After

a few hours use, the vapors will have disappeared and

the ﬂ ames will be at their normal height.

Flame Supervision Device

For your safety, this appliance is ﬁ tted with a ﬂ ame

supervision device which will shut-oﬀ the gas supply

if, for any reason, the pilot ﬂ ame goes out. This device

incorporates a ﬁ xed probe, which senses the heat

from the pilot ﬂ ame. If the probe is cool, the device will

prevent any gas ﬂ ow unless manually lighting the pilot.

See full lighting instructions on page 14 of this manual.

Introduction

Thank You ...

For purchasing a Valor by Miles Industries. Your new

radiant gas heater is a technical appliance that must

be installed by a qualiﬁ ed dealer. Each Valor ﬁ replace

is fully tested during the production process for your

safety and comfort.

Your unit has been professionally installed by:

Dealer Name: ________________________________

Phone Number :_______________________________

Should you encounter an operational problem, call

your dealer immediately.

Do not try to repair the unit as you may cause an

injury or damage the ﬁ replace.

Locating Fireplace & Lighting Information

Card

The Fireplace and Lighting Information card is located at

the right hand side of the ﬁ replace opening. The card is

attached under the plinth.

To access the card, remove the barrier screen, side

doors and the plinth. Grab the card and pull it out.

There is important information on both sides of the

card.

739MN

FOR NATURAL GAS POUR LE GAZ NATUREL

750

24,000

6,500

3.2"

5.0"

4006176N/01

CIRCULATING FAN KIT 755CFK VENTILAT EUR POUR CIRCULATION D'AIR 755CFK

#4003360-741, #4003293-742, #4003313-745, #4003426-765, #4004666 772

120V, 60Hz, LESS THAN 1A 120V, 60Hz, MOINS DE 1A

739N 10000

Fireplace

model

Serial

number

Performance of propane gas appliances may be

aﬀ ected by the quality of commercial gas sup-

plied in your area.

Info

card

Window

The info card is located behind the front

panel below the window.

OWNER’S

INFORMATION

7

Gas valve

Battery holder

& wall switch

Fireplace

Receiver Gas valve

The receiver and gas valve are located on the bottom of the

ﬁ replace behind the front panel. The battery holder is located

next to the wall switch.

Thermostatic

Remote

Control

Wall SwitchRemote control

handset

ON: parallel to pipe OFF:

perpendicular

to pipe

Wall Switch

Fireplace Control Devices

There are two ways to control your

ﬁ replace.

1. Thermostatic Remote Control

can be programmed to function

automatically—see pages 8–12;

2. Wall Switch turns ﬁ re on, oﬀ and

controls ﬂ ame height—see page 13.

How to Turn Your Fireplace ON

Press and hold button(s) until a short beep conﬁ rms the

start sequence has begun; release buttons.

Continuing beeps conﬁ rm the ignition is in process.

When the pilot is lit, the gas ﬂ ows—see Using the

Remote Control section for more information.

How to Turn Your Fireplace OFF (and pilot)

Press and hold the OFF button for a second (either on

the handset or the wall switch).

If the ﬂ ames are on, they go down and you hear the

valve motor wind down. You hear a clunk and a beep

indicating that the valve has received the signal from

the remote control.

In the unlikely event that you cannot turn oﬀ your

ﬁ replace with the remote control handset, use the

wall switch; if the wall switch malfunctions and will not

turn oﬀ the ﬁ replace, wait 6 hours and the ﬁ replace

will automatically go to pilot. You can then access the

controls inside your ﬁ replace.

Alternately, turn oﬀ gas supply. In all cases, call your

dealer for service assistance.

How to Ensure Your Fireplace Cannot

Be Turned ON Inadvertently

You can use one of the two following methods to

ensure that your ﬁ replace will not turn on when you

don’t want it on.

• On gas valve, turn dial from ON

position to MAN position as

shown. Turning dial to MAN will

ensures that main burner cannot

come on. The pilot will remain on

if lit.

• Alternately, remove all batteries

from the battery holder next to the

wall switch as well as the battery

from the handset.

Automatic Shut-Oﬀ (in

certain conditions)

Your ﬁ replace’s remote control is equipped with an

automatic shut-oﬀ mechanism which is activated

in certain conditions. See page 12 in the Using the

Remote Control section for a description of this feature.

Operating Your Fireplace

WARNING

RISKS OF SEVERE BURNS! SURFACES OF

THE FIREPLACE ARE VERY HOT DURING

OPERATION! Ensure ﬁ replace has cooled oﬀ

before accessing controls.

!

Wall SwitchRemote control

handset

OWNER’S

INFORMATION

8

Using the Remote Control

5DGLR)UHTXHQF\

0+]IRU86$DQG&DQDGD

7KLVGHYLFHFRPSOLHVZLWK3DUWRIWKH)&&5XOHV

DQGZLWK,QGXVWU\&DQDGDOLFHQVHH[HPSW566

VWDQGDUGV2SHUDWLRQLVVXEMHFWWRWKHIROORZLQJWZR

FRQGLWLRQV

WKLVGHYLFHPD\QRWFDXVHKDUPIXOLQWHUIHUHQFHDQG

WKLVGHYLFHPXVWDFFHSWDQ\LQWHUIHUHQFHUHFHLYHG

LQFOXGLQJLQWHUIHUHQFHWKDWPD\FDXVHXQGHVLUHG

RSHUDWLRQ

127(%HIRUHXVLQJWKHUHPRWHFRQWUROV\VWHPIRU

WKH¿UVWWLPHWKHUHFHLYHUDQGWKHKDQGVHWPXVWEH

V\QFKURQL]HG6HHWKHVHFWLRQ Synchronize Remote

Control

,03257$17BEFORE YOU BEGIN, please note that

on this system, the settings of time, temperature and

automatic ON/OFF can only be programmed when

the function display is ﬂ ashing. Be patient when

programming as it can take a few seconds to set.

1RWH,QWKH7(03RU7,0(5PRGHVWKHUHPRWHKDQGVHW

VHQVHVWKHURRPWHPSHUDWXUHDQGDGMXVWVWKHÀDPH

DFFRUGLQJO\

7RFRPPXQLFDWHWKHKDQGVHWVKRXOGEHZLWKLQIHHW

PHWHUVRIWKH¿UHSODFH

Do not leave the handset on the mantel or hearth.

6(7(scrolls

through

modes and

settings)

2))(returns

to set mode,

turns the burner

and the pilot o)

Large ame

button (ames

up, sets hours,

temperature)

Small ame

button (ames

down and o,

sets minutes,

temperature)

Current

temperature

(F or C)

Current time

(12 or 24 hour clock)

Modes (Manual,

Temperature, Timer)

Handset

sensor

Battery status

Current

programmed

period (Timer)

Period

start or end

(Temp, Timer)

:KHQWKHSLORWLVRႇLWZLOOWDNH

PLQXWHVEHIRUHLWFDQEHOLWDJDLQ

72785121$33/,$1&( 7278512))$33/,$1&(

)/$0(+(,*+7$'-8670(17

2QWKHYDOYHWXUQ0$1NQRERQWKH21IXOO

FRXQWHUFORFNZLVHSRVLWLRQ

3ODFH212))VZLWFKLIHTXLSSHGLQ,21SRVLWLRQ

67$1'%<02'(3LORW)ODPH

3UHVVDQGKROGVPDOOÀDPHWRVHWDSSOLDQFHDW

SLORWÀDPH

6LPXOWDQHRXVO\SUHVVWKH2))DQG

ODUJHÀDPHEXWWRQVXQWLODVKRUW

EHHSFRQ¿UPVWKHVWDUWVHTXHQFHKDV

EHJXQUHOHDVHEXWWRQV

&RQWLQXLQJEHHSVFRQ¿UPWKHLJQLWLRQLV

LQSURFHVV

2QFHSLORWLJQLWLRQLVFRQ¿UPHGWKHUHLV

PDLQJDVÀRZ

$IWHUPDLQEXUQHULJQLWLRQWKHKDQGVHW

ZLOODXWRPDWLFDOO\JRLQWRPDQXDO0$1

FRQWUROPRGH

3UHVV2))EXWWRQ

:KHQWKHSLORWLVRႇLWZLOOWDNH

PLQXWHVEHIRUHLWFDQEHOLWDJDLQ

,QVWDQGE\PRGH3UHVVDQGKROG

ODUJHÀDPHEXWWRQWRLQFUHDVH

ÀDPHKHLJKW

&$87,21

:KHQSLORWLJQLWLRQLVFRQ¿UPHGPRWRUWXUQV

DXWRPDWLFDOO\WRPD[LPXPÀDPHKHLJKW

OWNER’S

INFORMATION

9

Using the Remote Control

6(77,1*7+(7,0(

6(77,1*&+525)+5&/2&.

02'(62)23(5$7,21

127(0DQXDOPRGHFDQDOVREH

UHDFKHGE\SUHVVLQJHLWKHUWKH

ODUJHÀDPHRUWKHVPDOO

ÀDPHEXWWRQV

3UHVVDQGKROGVPDOOÀDPH

EXWWRQWRGHFUHDVHÀDPHKHLJKWRUWR

VHWWKHDSSOLDQFHDWSLORWÀDPH

)RU¿QHDGMXVWPHQWWDSWKHODUJH

ÀDPHRUVPDOOÀDPHEXWWRQV

'RXEOHFOLFNVPDOOÀDPHEXWWRQ

³/2´ZLOOEHGLVSOD\HG

127()ODPHJRHVWRKLJK¿UH¿UVW

EHIRUHJRLQJWRGHVLJQDWHGORZ¿UH

,Q0$1PRGHSUHVV2))DQG

VPDOOÀDPHEXWWRQVXQWLOGLVSOD\

FKDQJHVIURP)DUHQKHLWKRXUFORFN

WR&HOVLXVKRXUFORFNDQGYLFH

YHUVD

7KHWLPHGLVSOD\ZLOOÀDVKDIWHUHLWKHU

,QVWDOOLQJWKHEDWWHU\RU

6LPXOWDQHRXVO\SUHVVLQJWKH

ODUJHÀDPHDQGVPDOOÀDPH

EXWWRQV

3UHVVODUJHÀDPHEXWWRQWRVHW

WKHKRXU

3UHVVVPDOOÀDPHEXWWRQWRVHW

WKHPLQXWH

3UHVV2))RUVLPSO\ZDLWWRUHWXUQWR

0$1PRGH

'RXEOHFOLFNODUJHÀDPHEXWWRQ

)ODPHDXWRPDWLFDOO\JRHVWRKLJK¿UH

³+,´ZLOOEHGLVSOD\HG

0DQXDO0RGH0DQXDO

)ODPH+HLJKW$GMXVWPHQW

([SUHVV/RZDQG+LJK)LUH

'D\WLPH7HPSHUDWXUH

0RGH$SSOLDQFHPXVWEHLQ

VWDQGE\PRGHSLORWLJQLWHG7KH

URRPWHPSHUDWXUHLVPHDVXUHGDQG

FRPSDUHGWRWKHVHWWHPSHUDWXUH

7KHÀDPHKHLJKWLVWKHQDXWRPDWLFDOO\

DGMXVWHGWRDFKLHYHWKH'D\WLPH6HW

7HPSHUDWXUH

x 2

MAN

TEMP

%ULHÀ\SUHVVLQJWKH6(7EXWWRQ

FKDQJHVWKHPRGHRIRSHUDWLRQLQWKH

IROORZLQJRUGHU

ĺĺ

ĺĺDQGEDFNWR

MAN

TEMP

TIMER

1LJKWWLPH6HWEDFN

7HPSHUDWXUH0RGH$SSOLDQFHPXVW

EHLQVWDQGE\PRGHSLORWLJQLWHG

7KHURRPWHPSHUDWXUHLVPHDVXUHG

DQGFRPSDUHGWRWKH1LJKWWLPH

6HWEDFNWHPSHUDWXUH7KHÀDPH

KHLJKWLVWKHQDXWRPDWLFDOO\DGMXVWHG

WRDFKLHYHWKH1LJKWWLPH6HWEDFN

7HPSHUDWXUH

7LPHU0RGH$SSOLDQFHPXVW

EHLQVWDQGE\PRGHSLORWLJQLWHG

7KHWLPHUV3DQG33URJUDP

3URJUDPHDFKFDQEHSURJUDPPHG

WRJR21DQG2))DWVSHFL¿F

WLPHV)RULQVWUXFWLRQVVHH7LPHU

3URJUDPPLQJ0RGH

127(7KHGLVSOD\VKRZVWKHVHW

WHPSHUDWXUHHYHU\VHFRQGV

TEMP

TIMER

OWNER’S

INFORMATION

10

Using the Remote Control

6(77,1*7+(212))7(03(5$785(6

%ULHÀ\SUHVV6(7EXWWRQWRVFUROO

WR7(03VXQPRGH

+ROGWKH6(7EXWWRQXQWLOWKH7(03

ÀDVKHV

3UHVVODUJHÀDPHEXWWRQ

WRLQFUHDVHWKH'D\WLPH6HW

7HPSHUDWXUH

3UHVVVPDOOÀDPHEXWWRQ

WRGHFUHDVH'D\WLPH6HW

7HPSHUDWXUH

3UHVV2))RUVLPSO\ZDLWWRFRPSOHWH

SURJUDPPLQJ

6(77,1*7+(³'$<7,0(´7(03(5$785( 6(77,1*7+(³1,*+77,0(6(7%$&.´

7(03(5$785(

'HIDXOW6HWWLQJVVXQ&)

'HIDXOW6HWWLQJVPRRQ³´2))

3UHVVODUJHÀDPHEXWWRQWR

LQFUHDVH1LJKWWLPH6HWEDFN

7HPSHUDWXUH

3UHVVVPDOOÀDPHEXWWRQWR

GHFUHDVH1LJKWWLPH6HWEDFN

7HPSHUDWXUH

3UHVV2))RUVLPSO\ZDLWWRFRPSOHWH

SURJUDPPLQJ

%ULHÀ\SUHVV6(7EXWWRQWRVFUROO

WR7(03PRRQPRGH

+ROGWKH6(7EXWWRQXQWLOWKH7(03

ÀDVKHV

TEMP

7LS

6HWWKHGLႇHUHQWSDUDPHWHUVZKHQWKH\DUHÀDVKLQJ

OWNER’S

INFORMATION

11

Using the Remote Control

6(77,1*352*5$07,0(56

<RXFDQSURJUDPWZRSHULRGVRIWLPHEHWZHHQ

DPDQGSPLQHDFKKRXUF\FOH

7KH3URJUDPV3DQG3PXVWEHVHWLQWKHIROORZLQJ

RUGHUGXULQJDKRXUF\FOH

DQG

7KHLFRQLQGLFDWHVWKHEHJLQQLQJRIWKHSHULRG21

DQGWKHLFRQLQGLFDWHVWKHHQGRIWKHSHULRG2))

,I RU WKHSURJUDPPLQJLV

FDQFHOOHG

7RNHHSWKH¿UHSODFH21DOOQLJKWVHWDW

DPDQGDWDP

'HIDXOWVHWWLQJV

3URJUDPDPDP

3URJUDPSPSP

%ULHÀ\SUHVV6(7EXWWRQWRVFUROOWR

7,0(5PRGH

+ROGWKH6(7EXWWRQXQWLO

VXQLVGLVSOD\HGDQGWKHWLPH

ÀDVKHV

%ULHÀ\SUHVV6(7EXWWRQWRVFUROOWR

7,0(5PRRQZKLOHWKHWLPH

ÀDVKHV

3UHVVODUJHÀDPHEXWWRQWRVHW

WKHKRXU

3UHVVODUJHÀDPHEXWWRQWRVHW

WKHKRXU

3UHVVVPDOOÀDPHEXWWRQWRVHW

WKHPLQXWHV

3UHVVVPDOOÀDPHEXWWRQWRVHW

WKHPLQXWHV

6(77,1*3217,0( 6(77,1*3217,0(

%ULHÀ\SUHVV6(7WRVFUROOWR7,0(5PRGHVXQ

ZKLOHWKHWLPHÀDVKHV

)ROORZWKHLQVWUXFWLRQVJLYHQWRVHW321WLPH

6(77,1*32))7,0(

%ULHÀ\SUHVV6(7WRVFUROOWR7,0(5PRGH

PRRQZKLOHWKHWLPHÀDVKHV

)ROORZWKHLQVWUXFWLRQVJLYHQWRVHW32))WLPH

3UHVV2))EXWWRQWRVDYHWKHVHVHWWLQJV7KHWLPHUV

DUHSURJUDPPHG6HHWKHGLDJUDPRQSURJUDPPLQJ

VHTXHQFHVRQWKHIROORZLQJSDJH

7LS

,I\RXZDQWWRSURJUDPRQO\RQHSHULRGSURJUDP

DQGZLWKGHVLUHGWLPHVDQGSURJUDPDQG

ZLWKWKHVDPHWLPHDV

6(77,1*32))7,0(

P1

P2

P1

P2

OWNER’S

INFORMATION

12

Using the Remote Control

7LPHU3URJUDPPLQJ([DPSOHGHIDXOWWHPSHUDWXUHVVKRZQ

DP²

3

6WDUWWLPH

SP²

3

6WDUWWLPH

DP²

3

6WDUWWLPH

DP²

3

(QGWLPH

SP²

3

(QGWLPH

6HWWHPSÛ) 6HWWHPSÛ)6HWWHPSÛ)

6HWWHPSÛ)

$8720$7,&7851'2:1

$8720$7,&6+872))

/2:%$77(5<,1',&$7,21

+$1'6(75(&(,9(50$7&+

5HPRWHKDQGVHW7KHEDWWHU\LFRQZLOOVKRZ

ZKHQWKHEDWWHU\QHHGVWREHUHSODFHG5HSODFHZLWK

RQH9DONDOLQHEDWWHU\

5HPRWHEDWWHU\KROGHU)UHTXHQWµEHHSV¶IRU

VHFRQGVZKHQWKHYDOYHPRWRUWXUQVLQGLFDWHWKH

EDWWHULHVQHHGWREHUHSODFHG5HSODFHZLWKIRXU9

DONDOLQHEDWWHULHV

7KHUHPRWHFRQWUROKDQGVHWDQGUHFHLYHUDUH

SURJUDPPHGWRIXQFWLRQWRJHWKHU,QFDVHRID

UHSODFHPHQWRIWKHKDQGVHWRUWKHUHFHLYHU\RXZLOO

QHHGWRUHVHWWKHUHFHLYHUWRDOORZWKHPWRIXQFWLRQ

WRJHWKHU&RQWDFW\RXUGHDOHUIRUGHWDLOV

+RXUQR0RWRU0RYHPHQW

0DQXDO0RGH7HPSHUDWXUH7LPHU0RGH7KHYDOYHZLOO

WXUQWRSLORWÀDPHLIWKHUHLVQRFKDQJHLQÀDPHKHLJKW

IRUDKRXUSHULRG,Q7HPSHUDWXUH7LPHU0RGHLIWKH

DPELHQWURRPWHPSHUDWXUHFKDQJHVWKHÀDPHKHLJKW

ZLOODGMXVWDXWRPDWLFDOO\WRPDLQWDLQVHWWHPSHUDWXUH

DQGWKH¿UHZLOOFRQWLQXHWRIXQFWLRQQRUPDOO\7KHYDOYH

ZLOOWXUQWRSLORWÀDPHLIWKHVHWWHPSHUDWXUHDQGWKH

DPELHQWURRPWHPSHUDWXUHUHPDLQWKHVDPHRYHUD

KRXUSHULRG

/RZEDWWHULHVUHFHLYHU:LWKORZEDWWHU\SRZHULQWKH

UHFHLYHUEDWWHU\KROGHUWKHV\VWHPVKXWVRႇWKH¿UH

FRPSOHWHO\7KLVGRHVQRWDSSO\ZKHQWKHSRZHUVXSSO\

LVLQWHUUXSWHG

2Q'HPDQG3LORW7KLVJUHHQIHDWXUHHOLPLQDWHV

JDVHQHUJ\FRQVXPSWLRQGXULQJH[WHQGHGDSSOLDQFH

LQDFWLYLW\:KHQWKHDSSOLDQFHLVLQDFWLYHIRUGD\V

WKHV\VWHPDXWRPDWLFDOO\H[WLQJXLVKHVWKHSLORW7KLV

IHDWXUHKHOSVWKHFRQVXPHUUHDOL]HFRVWEHQH¿WVE\

DXWRPDWLFDOO\HOLPLQDWLQJHQHUJ\FRQVXPSWLRQGXULQJ

QRQKHDWLQJPRQWKVDQGOLPLWHGXVH

&$87,21

'212786(DVFUHZGULYHURURWKHUPHWDOOLFREMHFW

WRUHPRYHWKHEDWWHULHVIURPWKHEDWWHU\ER[RUWKH

KDQGVHW7KLVFRXOGFDXVHDVKRUWFLUFXLW

OWNER’S

INFORMATION

13

Using the Wall Switch

TO TURN APPLIANCE ON and OFF

TO ADJUST FLAME HEIGHT

Press ON-OFF button once to light

pilot. Press again to shut of pilot.

Press and hold large ﬂ ame button

to gradually increase ﬂ ame height.

Press and hold small ﬂ ame button to

gradually decrease ﬂ ame height.

The Wall Switch can be used to

control your ﬁ replace. You can

turn the pilot on or oﬀ and you can

increase or decrease the ﬂ ame

height.

Note that the thermostat and

programming functions are not

available with the wall switch.

Required Kits

Information accurate at the time of printing and subject

to change without notice.

Optional Accessories

Information accurate at the time of printing and subject

to change without notice.

Kits & Accessories

Fuel Beds (choose one)

1800DWK Driftwood Set Kit

1800DGM Decorative Glass Murano

1800SWK Split Wood Kit

Liners (choose one)

1815FBL Linear Fluted Black Liner Set

1835LML Limestone Liners

1825RGL** Linear Reﬂ ective Glass Liner Set

(**Add 1725RGL-3 Glass Retainer Kit)

Trims (choose one) Barrier

Screen

1850LSB Linear 5-1/4” Surround - black 4005460

1875LFB Linear 1” Finishing Trim Black 4005413

Conversion Kits

1800NGK Conversion to natural gas

1800PGK Conversion to propane gas

Other Accessories

GV60CKO Outdoor Fireplace Conversion Kit

1506DRK Additional rocks for Driftwood Kit

1595CFK Circulating Fan Kit

1270RBK Remote Blower Kit

LDK HeatShift Duct Kits (gravity ﬂ ow)

Hearth

Gate

Hearth gates such as Cardinal’s

VersaGates are available at retail stores

carrying safety products for children.

OWNER’S

INFORMATION

14

Lighting Instructions

FOR YOUR SAFETY, READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a ﬁ re or explosion may result

causing property damage, personal injury or loss of life.

A. This appliance has a pilot which must be lighted by hand, remote control, or wall switch. Follow these instructions

exactly. To save gas, turn the pilot oﬀ when not using the appliance for a prolonged period of time.

B. BEFORE LIGHTING, smell all around the appliance area for gas. Be sure to smell next to the ﬂ oor because

some gases are heavier than air and will settle on the ﬂ oor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electric switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the ﬁ re department.

C. Use only your hand to push in or turn the control knobs. Never use tools. If the knobs will not push in or turn by

hand, don’t try to repair them; call a qualiﬁ ed service technician. Force or attempted repair may result in a ﬁ re or

explosion.

D. Do not use this appliance if any part has been under water. Immediately call a qualiﬁ ed service technician to

inspect the appliance and to replace any part of the control system and any gas control, which has been under water.

LIGHTING INSTRUCTIONS

1. STOP! Read the safety information above.

2. TO CLEAR ANY GAS, turn main valve oﬀ by pressing OFF (red dot) button on remote handset

(1).

• Wait ﬁ ve (5) minutes to clear out any gas, then smell for gas, including near the ﬂ oor. If you

smell gas, STOP! Follow “B” in the safety information above on this label. If you don’t smell

gas, go to the next step.

3. AUTOMATIC IGNITION: MAN-knob (2) in ON position. Ensure Flame Adjustment

knob (3) is set to lowest setting () (Fig. 1). Locate the pilot (Fig. 3.) inside of

ﬁ rebox at left hand side.

• On the remote control handset, press the OFF button (red dot) and large ﬂ ame

button () simultaneously; a short acoustic signal conﬁ rms the start has begun.

• Further short acoustic signals indicate the ignition process is in progress.

• When the pilot is lit, the Flame Adjustment knob (3) will automatically rotate to

the highest setting.

• Press the small ﬂ ame button () on the remote control handset to reduce the

ﬂ ame height.

4. MANUAL IGNITION: MAN-knob (2) in MAN position (Fig. 2). With the window

oﬀ , locate the pilot (Fig. 3) inside of ﬁ rebox at left hand side.

• Set Flame Adjustment knob (3) to the lowest setting ().

• Push down the metallic core (4) with a pen or similar instrument; this will establish

the pilot gas ﬂ ow.

• Light gas at the pilot (5) with a match.

• Continue holding down metal core (4) for about 10 seconds; after release, pilot

should remain lit.

• If the pilot will not stay lit after several tries, turn the gas control knob (3) to OFF () and call your local

service technician or gas supplier.

• Reinstall the window and set the MAN-knob (2) to ON; turn Flame Adjustment knob (3) up () or down ()

manually or use the ﬂ ame buttons ()() on the remote control handset to adjust the ﬂ ame height.

TO TURN OFF GAS TO APPLIANCE

AUTOMATIC SHUT-OFF (using the remote control handset):

• Press and hold the small ﬂ ame button () on the remote control handset to shut-oﬀ the main burner gas ﬂ ow.

• Press OFF button (red dot) on remote handset to shut-oﬀ the appliance, including pilot ﬂ ame.

Spark

Pilot

Fig 3

Fig 1

Fig 2

1

OFF

5

OWNER’S

INFORMATION

15

Servicing Your Fireplace

We recommend having your ﬁ replace serviced every year. Contact your supplier quoting the model

number. It will be helpful if the appliance’s serial number can also be quoted. These numbers are

on the information card. The replacement parts are shown at the end of this manual. Please always

quote the part number and description when requesting spare parts.

Safe Operation List

To be performed by a qualiﬁ ed technician only

1. Inspect and operate the pressure relief mechanism to verify relief mechanisms are free from

obstruction to operate. See Cleaning Your Fireplace: To reﬁ t the window section of this manual.

2. Clean glass window with a suitable ﬁ replace glass cleaner. Abrasive cleaners must not be used.

Be careful not to scratch the glass when cleaning. See Cleaning Your Fireplace section of this manual.

3. Inspect the operation of the ﬂ ame safety system Pilot or Flame rectiﬁ cation device.

4. Inspect and ensure the lighting of the main burner occurs within 4 seconds of the main gas valve

opening. Visual inspection should match that outlined in the appliance instruction manual. Inspect

primary air openings for blockage. See Checking Pilot and Burner Flame section of this manual.

5. Inspect condition of vent and vent terminal for sooting or obstruction and correct if present.

6. Vacuum and clean any debris in the ﬁ rebox that is not supposed to be there.

7. Test and measure the ﬂ ame failure response time of the ﬂ ame safety system.

It must de-energize the safety shutoﬀ in no more than 30 seconds.

8. Check all accessible gas-carrying tubes, connections, pipes and other components for leaks.

See Set up Gas Supply section of this manual.

Annual Inspection

In order to maintain the safe operation of your ﬁ replace, contact your dealer to have a qualiﬁ ed

technician go over the list below and make the necessary veriﬁ cations at least once every year.

Maintaining Your Fireplace

OWNER’S

INFORMATION

16

WARNING

CHOKING HAZARD! Ensure that the ﬁ replace

area is clear of ﬁ rebed particles as these could

be ingested by small children. Vacuum thoroughly

around the ﬁ replace area after cleaning.

WARNING

DO NOT TOUCH THE GLASS WHILE IT IS HOT!

Let the ﬁ replace cool ﬁ rst before cleaning it.

!

Cleaning Your Fireplace

Important - Glass cleaning - Mineral deposits

One of the by-products of the combustion process in

a gas appliance is a mineral which can show up as a

white ﬁ lm on the ceramic glass of the viewing door.

The composition of the deposit varies with location and

time. It is believed to be associated with the varying

sulfur content of the gas. You may have the problem

intermittently.

We have consulted with ceramic glass manufacturers

and they cannot oﬀ er a deﬁ nitive solution to this prob-

lem. Dealers have tried various cleaning products with

varying results. The following are recommendations

only and are not meant to guarantee results.

NOTE: This is a problem beyond Miles Industries’

control and is not covered under warranty.

• Clean the glass regularly as soon as you notice

the buildup (white ﬁ lm). If the ﬁ lm is left for a longer

period of time, it will etch into the glass. It is then

much harder, if not impossible, to remove.

• NEVER use an abrasive cleaner or ammonia-

based cleaner on the ceramic glass. Any

abrasion of the surface has the immediate eﬀ ect of

compromising the strength of the glass. An emulsion

type cleaner is recommended.

• Use a soft damp cloth to apply the cleaner. Dry the

glass with a soft, dry, preferably cotton cloth. Most

paper towels and synthetic materials are abrasive to

ceramic glass and should be avoided.

• Our dealers have had good results from the

products listed below. We cannot, however,

guarantee the results of these products.

◊ Brasso, Polish Plus by Kelkem, Cook Top Clean

Creme by Elco, White Oﬀ by Rutland, Turtle Wax

Do not clean the glass while it is hot!

Always securely replace the window and the barrier

screen before lighting.

If broken, the glass pane may only be replaced

as a complete window unit as supplied by the

manufacturer.

If the barrier becomes damaged, the barrier shall

be replaced with the manufacturer’s barrier for this

appliance.

Clean the window panes following the guidelines in this

section.

Clean the steel trim with mild soap and warm water.

Any alcohol/solvent base cleaner will weaken the coat-

ing and damage it.

Clean the barrier screen dusting it with a soft brush.

Clean the ﬁ rebox ceramic logs/rocks and walls dusting

them with a soft brush. Dust can also be removed from

the burner using a soft brush after removing the fuel

bed. When cleaning, make sure that no particles are

brushed into the slots of the burner.

To remove the window for cleaning, we suggest

you get help from another person as the window

is long and heavy:

1. Remove the barrier screen.

2. Remove the side doors and the plinth.

3. Remove plinth support bracket.

4. Find the levers on each

side of the window

towards the top. Using

your ﬁ nger, pull the levers

towards you and unhook

them from the window

frame brackets.

Maintaining Your Fireplace

Spring Loaded Window Levers

Remove plinthRemove side doors

OWNER’S

INFORMATION

17

Window frame

Bottom railing

5. Gently pull the top of the window outward.

6. Lift the window out of its bottom railing and set it

aside in a safe place to avoid damage.

To reﬁ t the window:

1. Place the window in its bottom railing. Ensure to

remove any vermiculite or glass particles in

the railing before installing the window.

2. Push the top

of the window

frame against

the ﬁ rebox.

3. While you hold it, pull the side levers

back into the window brackets on each side.

1

2

3

WARNING

Failure to install the window correctly can

leak carbon monoxide, aﬀ ect the performance

of the ﬁ replace, damage components, cause

overheating resulting in dangerous conditions.

Damage caused by incorrect window installa-

tion is not covered by the Valor warranty.

!

DANGER

The window unit must be correctly installed,

fastened and sealed after servicing or serious

bodily injury and/or damage to the appliance

may result.

To ensure a safe operation:

• Double-check that the bottom of the window

frame is correctly installed in the bottom

support railing;

• Verify that the levers are hooked properly to

the window tabs then;

• Pull out the top of the window and release it

to insure the springs return it;

• Ensure the window is sealed before operation.

!

Maintaining Your Fireplace

Hot Glass Warning Plate

4. Apply ﬁ rm hand pressure around the window frame to

ensure the window is sealed tight against the ﬁ rebox.

5. If the Hot Glass Warning plate has been removed

from the front lower corner of the window,

reinstall it by sliding it between the glass and

the frame as indicated.

OWNER’S

INFORMATION

18

1800DWK—Driftwood

Correct Flame Appearance

1800DGM—Decorative Glass Murano

1800SWK—Split Wood

Pilot Flame Thermocouple Probe

must be in Flame

Checking Pilot and Burner Flames

A periodic check of the pilot and burner ﬂ ames should

be made. Check after the ﬁ re has been on for at least

30 minutes. The pilot ﬂ ame must cover the tip of the

thermocouple probe. The main burner ﬂ ame pattern will

vary from appliance to appliance depending on the type

of installation and climatic conditions.

The appliance area must always be kept clear and

free from combustible materials, gasoline and other

ﬂ ammable vapors and liquids.

Inspect the vent terminal outdoors regularly to make

sure that snow, trees, bushes, leaves, or other objects

do not obstruct it.

Examine the vent system and terminal regularly. We

recommend annually.

Maintaining Your Fireplace

Pilot Flame can be seen at the back

of the ﬁ re bed on the left hand side

Pilot Flame can be seen at the back

of the ﬁ re bed on the left hand side

Pilot Flame can be seen at the back

of the ﬁ re bed on the left hand side

WARNING

FOR SAFETY PURPOSE, ensure the barrier

screen is re-installed on the fireplace after

maintenance.

!

6. Reinstall the plinth support bracket hooking it up to

the stiﬀ ener bracket located below the window as

shown.

7. Reinstall the plinth and side doors.

8. Reinstall the barrier screen on the trim..

9. Verify that the screen is properly hooked to the trim

and secure.

Plinth

support

bracket

Stiﬀ ener

bracket

OWNER’S

INFORMATION

19

WARNING

DO NOT ATTEMPT TO CHANGE THE BATTER-

IES WHILE THE FIREPLACE IS STILL HOT! Let

the ﬁ replace cool ﬁ rst before touching it.

CAUTION

DO NOT USE a screwdriver or other metallic object

to remove the batteries from the battery holder or

the handset! This could cause a short circuit.

Battery holder

& wall switch

Fireplace

The battery holder is located beside the wall switch.

Disconnect

connector

!

Replacing Batteries

Low batteries signal: see page 12.

BEFORE changing the batteries, turn the ﬁ replace

oﬀ (including pilot).

The appliance uses four 1.5 V AA alkaline batteries

located next to the wall switch and one 9 V alkaline

battery in its handset. Batteries should last one to two

seasons, depending on usage. Removing the batteries

in the oﬀ -season will extend the battery life.

To replace the batteries:

The battery compartment is located next to the wall

switch in the vicinity of the ﬁ replace. Its front plate is

attached with magnets to the wall switch box.

1. Pull on the plate next to the wall switch to access

the batteries.

2. Disconnect the snap connector from the battery

holder. Do not pull the connector by the wire!

3. Replace the batteries with 4 AA alkaline batteries

orienting them as indicated inside the holder.

4. Reconnect the snap connector to the battery holder.

5. Put the battery holder back in its place beside the

wall switch and snap it in place.

Using Handset Wall Holder

Your ﬁ replace equipment includes a wall

holder to store the handset. If it hasn’t be

installed, refer to the instructions further

on in this manual for the installation.

Maintaining Your Fireplace

OWNER’S

INFORMATION

20

X

Model JN JP

Gas Natural Propane

Altitude (Ft.)* 0-4,500 feet*

Input Maximum (Btu/h) 42,000 42,000

Input Minimum (Btu/h) 23,000 23,000

Manifold Pressure (in w.c.) 3.5” 10”

Minimum Supply Pressure (in

w.c.) 5” 11”

Maximum Supply Pressure (in

w.c.) 10” 14”

Main Burner Injector Marking 1400 DMS#47

Pilot Injector Marking 51 30

Min. Rate By-Pass Screw 260 160

Approval & Codes

This appliance is certiﬁ ed to ANSI Z21.88-2016/CSA

2.33-2016 American National Standard / CSA Standard

for Vented Gas Fireplace Heaters for use in Canada

and USA, and to CGA 2.17-91 High Altitude Standard in

Canada. This appliance is for direct vent installations.

This appliance complies with CSA P.4.1-15 Testing

method for measuring annual ﬁ replace eﬃ ciencies.

The installation must conform to local codes or, in the

absence of local codes, with the National Fuel Gas Code,

ANSI Z223.1/NFPA 54 or the Natural Gas and Propane

Installation Code CAN/CGA-B149.1. Only qualiﬁ ed

licensed or trained personnel should install this appliance.

This appliance must be electrically grounded in

accordance with local codes, or, in the absence of local

codes, with the National Electrical Code, ANSI/NFPA

70 or the Canadian Electrical Code, CSA C22.1.

Ratings

*High Altitude Installations

Input ratings are shown in BTU per hour and are

certiﬁ ed without deration for elevations up to 4,500 feet

(1,370 m) above sea level.

For elevations above 4,500 feet (1,370 m) in USA,

installations must be in accordance with the current

ANSI Z223.1 and/or local codes having jurisdiction.

Heating value of gas in some areas is reduced to

compensate for elevation—consult your local gas

utility to conﬁ rm.

For installations at elevations above 4,500 feet

(1,370 m) in Canada, please consult provincial and/or

local authorities having jurisdiction.

Supply Gas

Heater engine 1800JN is used with natural gas.

Heater engine 1800JP is used with propane gas.

Speciﬁ cations

The supply pressure must be

between the limits shown in

the Ratings section above.

The supply connection is

3/8” NPT male and located

on the left hand side of the

ﬁ rebox. A shut-oﬀ valve (not supplied) is required on

the supply line to isolate the unit during service. See

Supply Gas Installation section for details.

Conversion Kits

The 1800J L3 is supplied as natural gas or propane gas

and is ﬁ eld convertible between fuels. See instructions

packaged with the conversion kit for further information.

Electrical

The 1800J is designed to run on battery power and

does not require an electrical power source to operate

as a heater. However, it requires electrical power

to operate optional 1595CFK Circulating Fan Kit or

1270RBK Remote Blower Kit.

LDK HeatShift Duct Kit

The 1800J is designed to allow the installation of the

optional LDK HeatShift Duct Kit, a convection system

that redistributes the warm air ﬂ ow away from the

ﬁ replace opening to a more desirable location using

natural convection, without use of a fan.

The warm air ﬂ ow may be relocated to a position higher

up the wall, out the sidewalls, or even to another room.

The result is much cooler wall temperatures above the

ﬁ replace opening for locating televisions, artwork, etc.

Please note that the framing and mantel clearances

are aﬀ ected by the installation of the LDK. Refer to

the installation manual packed with the kit for more

information.

This appliance is designed and approved as a

supplemental heater and provides the potential

for most energy conservation when used while

attended. The use of an alternate primary heat

source is advisable.

Outdoor Conversion Kit

The 1800J models are supplied standard for indoor

applications and may be adapted for installation

in speciﬁ c “outdoor” applications protected from

weather as deﬁ ned in the GV60CKO outdoor

conversion kit manual.

WARNING

Optional electrical accessories

ARE NOT ALLOWED when adapting

appliance for outdoor use.

!

QUALIFIED

INSTALLER

La page est en cours de chargement...

Valor 1800JN/JP Le manuel du propriétaire

Valor 1800JN/JP Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents