VTech LF2911 Mode d'emploi

Marque: VTech

Modèle: LF2911

Catégorie: Moniteurs vidéo bébé

Taper: Mode d'emploi

Touch and learn!

LF2911

High DefinitionHigh Definition

Pan & Tilt CameraPan & Tilt Camera

Need help?

Visit leapfrog.com/support

Parent Guide

This guide contains important information.

Please keep it for future reference.

Visit our website leapfrog.com leapfrog.com for more information

about products, downloads, resources and more.

Read our complete warranty policy online at

leapfrog.com/warranty.

Scan the QR

code to enter our

Online Manual:

Or go to leapfrog.com/support

UL STD.

62368-1

CERTIFIED TO

CSA STD.

C22.2 NO.62368-1

CONFORMS TO

Important Safety Instructions

The applied nameplate is located at the bottom of the camera’s base.

When using your equipment, basic safety precautions should always

be followed to reduce the risk of fire, electric shock and injury,

including the following:

1. Follow all warnings and instructions marked on the product.

2. Adult setup is required.

3. CAUTION: Do not install the camera at a height above 2 meters.

4. This product is not a substitute for adult supervision of the infant.

Supervising the infant is the parent’s or caregiver’s responsibility.

This product could cease operating, and therefore you should not

assume it will continue working properly for any given period of

time. Further, this is not a medical device and should not be used

as such. This product is intended to assist you in supervising your

baby.

5. Do not use this product near water. For example, do not use it next

to a bath tub, wash bowl, kitchen sink, laundry tub or swimming

pool, or in a wet basement or shower.

6. Use only the adapters included with this product. Incorrect

adapter polarity or voltage can seriously damage the product.

Power adapter information:

Camera Output: 5V DC 1A;

VTech Telecommunications Ltd.; Model: VT05EUS05100

7. The power adapters are intended to be correctly oriented in a

vertical or floor mount position. The prongs are not designed to

hold the plug in place if it is plugged into a ceiling, under-the-

table or cabinet outlet.

8. For pluggable equipment, the socket-outlet shall be installed

near the equipment and shall be easily accessible.

9. Unplug this product from the wall outlet before cleaning.

10. Do not use liquid or aerosol cleaners. Use a damp cloth for

cleaning. Do not cut off the power adapters to replace them with

other plugs, as this causes a hazardous situation.

11. Do not allow anything to rest on the power cords. Do not install

this product where the cords may be walked on or crimped.

12. This product should be operated only from the type of power

source indicated on the marking label. If you are not sure of the

type of power supply in your home, consult your dealer or local

power company.

13. Do not overload wall outlets or use an extension cord.

14. Do not place this product on an unstable table, shelf, stand or

other unstable surfaces.

15. This product should not be placed in any area where proper

ventilation is not provided. Slots and openings in the back or

bottom of this product are provided for ventilation. To protect

them from overheating, these openings must not be blocked by

placing the product on a soft surface such as a bed, sofa or rug.

This product should never be placed near or over a radiator or

heat register.

16. Never push objects of any kind into this product through the

slots because they may touch dangerous voltage points or create

a short circuit. Never spill liquid of any kind on the product.

17. To reduce the risk of electric shock, do not disassemble this

product, but take it to an authorized service facility. Opening or

removing parts of the product other than specified access doors

may expose you to dangerous voltages or other risks. Incorrect

reassembling can cause electric shock when the product is

subsequently used.

18. You should test the sound reception every time you turn on the

units or move one of the components.

19. Periodically examine all components for damage.

20. There is a very low risk of privacy loss when using certain

electronic devices, such as cameras, cordless telephones, etc. To

protect your privacy, make sure the product has never been used

before purchase, reset the camera periodically by powering off

and then powering on the units, and power off the camera if you

will not use it for some time.

21. Children should be supervised to ensure that they do not

play with the product.

22. The product is not intended for use by persons (including

children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning

use of the appliance by a person responsible for their safety.

SAVE THESE INSTRUCTIONS

Cautions

1. Use and store the product at a temperature between 32oF

(0oC) and 104oF (40oC).

2. Do not expose the product to extreme cold, heat or direct

sunlight. Do not put the product close to a heating source.

3. Warning—Strangulation Hazard—

Children have STRANGLED in cords. Keep this

cord out of the reach of children (more than 3 ft

(0.9m) away). Do not remove this tag.

4. Never place the camera(s) inside the baby’s

crib or playpen. Never cover the camera(s) with

anything such as a towel or a blanket.

5. Other electronic products may cause interference with your

camera. Try installing your camera as far away from these

electronic devices as possible: wireless routers, radios, cellular

telephones, intercoms, room monitors, televisions, personal

computers, kitchen appliances and cordless telephones.

Precautions for users of implanted cardiac pacemakers

Cardiac pacemakers (applies only to digital cordless devices):

Wireless Technology Research, LLC (WTR), an independent

research entity, led a multidisciplinary evaluation of the

interference between portable wireless devices and implanted

cardiac pacemakers. Supported by the U.S. Food and Drug

Administration, WTR recommends to physicians that:

Pacemaker patients

• Should keep wireless devices at least six inches from the

pacemaker.

• Should NOT place wireless devices directly over the

pacemaker, such as in a breast pocket, when it is turned ON.

WTR’s evaluation did not identify any risk to bystanders with

pacemakers from other persons using wireless devices.

Electromagnetic fields (EMF)

This LeapFrog product complies with all standards regarding

electromagnetic fields (EMF). If handled properly and according

to the instructions in this user’s manual, the product is safe to be

used based on scientific evidence available today.

What’s Included Download LeapFrog Baby Care App +

Connect and Power On the Camera

On LeapFrog Baby Care App+

Before you start...

• Connect your mobile device to a 2.4GHz Wi-Fi network for a better connection and smoother video

streaming.

• Enable the Location Service of your mobile device for the purpose of camera setup.

With a Wi-Fi network and enabled Location Service...

You can start to pair the camera with your own mobile device following the instructions in the app. Upon

the successful pairing, you can hear and watch your baby via your mobile device.

Tips:

• Move the camera and the Wi-Fi router closer to each other in order to strengthen the network signal.

• It takes up around 1 minute to search the camera.

Parent Guide

x 2 x 2

App Compatibility

• AndroidTM 6.0 or later

• iOS 12 or later.

Start monitoring from anywhere.

Scan the QR code to download the free LeapFrog Baby Care mobile app, or search “LeapFrog Baby

Care+” on Apple App Store or Google Play Store.

Strangulation

Hazard

Keep this cord out of reach of children.

The cord needs to be at least three feet

away from the child at all times. Do not

use with an extension cord. Do not

remove this tag.

Éloignez ce cordon des enfants. Le

cordon doit se trouver à au moins trois

pieds d’un enfant et ce, en tout temps.

N’utilisez pas de rallonge. Ne retirez pas

cette étiquette.

Mantenga este cable fuera de la alcance

de los niños. Este cable debe estar por

lo menos tres pies fuera de la alcance

del niño en todo momento. No lo use

con una extensión inalámbrica. No quite

esta etiqueta.

Risque

d’étranglement

Riesgo de

estrangulación

Notes:

• Use only the power adapter supplied with this product.

• If the camera is connected to a switch controlled electric outlet, make sure the switch is on.

• Connect the power adapters in a vertical or floor mount position only. The adapters’ prongs are not designed to hold

the weight of the camera, so do not connect them to any ceiling, under-the-table, or cabinet outlets. Otherwise, the

adapters may not properly connect to the outlets.

• Make sure the camera and the power adapter cords are out of reach of children.

• To maintain compliance with the FCC’s RF exposure guidelines, place the camera at least 20cm from nearby persons.

Pair the Camera with your Mobile Device

After installing the LeapFrog Baby Care App+...

• Sign up for an account

• Pair the camera with your mobile device

• Monitor your baby using a wide range of features

Tip:

• You can find the wall mounting tutorial video and

step-by-step guide by visiting our Online Manual.

> 3ft (1m) 2

Adjust the angle of the baby

unit to aim at your baby.

Position the Camera

Overview

13 14

1Infrared LEDs

2Light sensor

3Microphone

4Camera

5Night light

6 Night light control key

• Tap to turn the night light on or off.

• Tap and hold to adjust night light

brightness level.

7Speaker

8Vents

9Temperature sensor

10 Privacy switch

11 Power LED light

12 Wall mount slot

13 Power jack

14 PAIR key

• Press and hold to pair the camera with

your mobile devices.

Camera

1. Connect the Camera

2. Power On or Off the Camera

• Camera turns on automatically after it connects to the power

socket.

• Disconnect from the power supply to power off.

Note:

• POWER LED Light is OFF by default.

Designed for extra peace of mind, turn on Privacy Mode for a

moment of peace and quiet.

Slide the Privacy switch to turn on the privacy mode.

When the Privacy Mode is turned on, audio transmission

and video monitoring will be disabled so motion recording,

motion detection, and sound detection will be temporarily

unavailable.

Privacy mode

13 14

Cable Management

1 2 3

Your home Wi-Fi network provides Internet connection to your camera so that you can monitor and

control your camera whenever you are through the LeapFrog Baby Care App+.

Your Wi-Fi router (not included) provides the Internet connectivity, which serves as a communicating

channel.

If you plan to install your camera to a designated location, and will use your home Wi-Fi network to

connect your mobile device, test whether your selected monitoring areas have good Wi-Fi signal

strength. Adjust the direction and distance between your camera, mobile device and Wi-Fi router until

you have identified a suitable location with good connection.

Test the Location for the Camera

How the system works ?

Mobile access

Wi-Fi connection

FCC Part 15

This equipment has been tested and found to comply with the requirements for a Class

B digital device under Part 15 of the Federal Communications Commission (FCC) rules.

These requirements are intended to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one

or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

WARNING: Changes or modifications to this equipment not expressly approved by the

party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

To ensure safety of users, the FCC has established criteria for the amount of radio frequency

energy that can be safely absorbed by a user or bystander according to the intended usage

of the product. This product has been tested and found to comply with the FCC criteria. The

camera shall be installed and used such that parts of all persons’ body are maintained at a

distance of approximately 8 in (20 cm) or more.

This Class B digital apparatus complies with Canadian requirement: CAN ICES-3 (B)/

NMB-3(B)

Industry Canada

This device contains licence-exempt transmitter(s)/receiver(s) that comply with

Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).

Operation is subject to the following two conditions: (1) This device may not cause

interference. (2) This device must accept any interference, including interference that may

cause undesired operation of the device.

The term ‘’IC:‘’ before the certification/registration number only signifies that the Industry

Canada technical specifications were met.

This product meets the applicable Innovation, Science and Economic Development

Canada technical specifications.

RF radiation exposure statement

The product complies with FCC RF radiation exposure limits set forth for an uncontrolled

environment. The camera should be installed and operated with a minimum distance of

8 in (20 cm) between the camera and all persons’ body. Use of other accessories may not

ensure compliance with FCC RF exposure guidelines. This equipment complies also with

Industry Canada RSS-102 with respect to Canada’s Health Code 6 for Exposure of Humans

to RF Fields.

Mesures de sécurité importantes

La plaque signalétique appliquée est située au bas du socle de l’unité du bébé.

Lorsque vous utilisez votre appareil, vous devriez toujours suivre certaines mesures de precaution de base afin

de réduire les risques d’incendie, d’électrocution et de blessures corporelles, dont

ceux qui suivent :

1. Observez toutes les instructions et mises en garde inscrites sur l’appareil.

2. L’installation par un adulte est requise.

3. MISE EN GARDE: N’installez pas l’unité du bébé à une hauteur supérieure à 2 mètres.

4. Ce produit ne remplace pas la surveillance adulte du nourrisson. La supervision du nourrisson est

la responsabilité du parent ou de la personne qui s’occupe de l’enfant. Ce produit pourrait cesser

de fonctionner et, par conséquent, vous ne devriez pas présumer qu’il continuera de fonctionner

correctement pendant une période de temps donnée. De plus, il ne s’agit pas d’un instrument médical et

ne devrait pas être utilisé comme tel. Ce produit est destiné à vous aider à superviser votre bébé.

5. N’utilisez pas cet appareil près de l’eau ni de toute autre source d’humidité, par exemple, près d’une

baignoire, cuve à lessive, évier de cuisine, dans un sous-sol humide ni près d’une piscine, dans un soussol

humide ou une douche.

6. N’utilisez que les adaptateurs inclus avec ce produit. L’utilis ation d’un adaptateur dont la polarité ou la

tension serait inadéquate risque d’endommager sérieusement le pro duit et mettre votre sécurité en péril.

Informations sur les adaptateurs électriques :

Adaptateur de l’unité du bébé : Sortie : 5V DC 1A

VTech Telecommunications Ltd. Modèle: VT05EUS05100

7. Lorsqu’ils sont branchés dans une prise de courant, les adaptateurs secteur ont été conçus pour être

orientés correctement, soit à la verticale ou au plancher. Les broches n’ont pas été conçues pour supporter

le poids du bloc d’alimentation et le maintenir en place si celuici est branché dans une prise au plafond,

sous une table ou dans un meuble.

8. Pour les PRODUITS À BRANCHER À UNE PRISE DE COURANT, la prise de courant doit être installée près

du produit, afin d’assurer une accessibilité sécuritaire à la prise de courant.

9. Débranchez ce produit de la prise de courant avant de procéder au nettoyage. N’utilisez pas de nettoyants

en aérosols. Utilisez un chiffon humide pour le nettoyer.

10. Ne coupez pas les cordons d’alimentation pour remplacer les fiches, car ceci peut presenter un danger

potentiel.

11. Ne laissez aucun objet reposer ni appuyer sur le cordon d’alimentation. N’installez pas cet appareil dans un

endroit où l’on risque d’écraser le cordon d’alimentation ou de le piétiner.

12. Ne faites fonctionner cet appareil qu’avec le type d’alimentation indiqué sur l’étiquette. Si vous ne

connaissez pas le type d’alimentation que vous possédez à votre domicile, consultez votre marchand ou

votre compagnie locale d’électricité.

13. Ne surchargez pas les prises de courant murales ni les rallonges électriques.

14. Ne placez pas cet appareil sur un chariot, meuble, trépied, support de montage ni table chancelants.

15. Les trous et ouvertures du boîtier, situés à l’arrière de l’appareil ou sous celui-ci, servent à aérer l’appareil.

Pour l’empêcher de surchauffer, ne bloquez sous aucun prétexte ces ouvertures et n’empêchez pas

l’aération adéquate de l’appareil en le plaçant sur un lit, divan, tapis ou toute autre surface similaire. De

même, ne le positionnez pas à proximité ni au-dessus d’une source de chaleur ou d’un calorifère. De plus,

ne placez pas l’appareil dans un endroit avant de vous assurer qu’il y ait une bonne circulation d’air.

16. N’enfoncez jamais d’objets à travers les ouvertures de cet appareil, car ils pourraient entrer en contact avec

des points de tension dangereux ou causer des courts-circuits qui peuvent dégénérer en incendies ou en

risques d’électrocution. Ne renversez jamais de liquide dans ce produit.

17. Afin de réduire les risques d’électrocution, ne démontez pas cet appareil, mais apportez-le dans un

centre de service autorisé. L’ouverture du boîtier ou le retrait de toutes pièces que contient cet appareil,

à l’exception de l’accès autorisé à certaines portes ou ouvertures, risque de vous exposer à des points de

tension dangereux ou d’autres dangers. Un remontage incorrect peut par la suite présenter des risques

d’électrocution.

18. Vous devriez tester la réception chaque fois que vous mettez l’appareil en fonction.

19. Examinez les composantes afin de vérifier si celles-ci ne sont pas endommagées.

20. Il existe un très faible risque de perte de confidentialité avec certains appareils

électroniques (autres écoute-bébés, téléphones sans fils etc.). Pour l’éviter, s’assurer que le produit n’a

jamais été utilize avant l’achat, réinitialiser l’unité de façon périodique, éteindre l’écoute-bébé quand il n’est

pas en cours d’utilisation.

21. Les enfants devraient être supervisés afin de vous assurer qu’ils ne jouent pas avec l’appareil.

22. Le produit n’est pas conçu pour être utilisé par des personnes (incluant des enfants) aux capacités

physiques, sensorielles ou mentales réduites ou qui manquent d’expérience et de connaissances, à moins

qu’on leur ait donné suffisamment de supervision ou d’instructions relativement à l’utilisation de l’appareil

par une personne responsable de leur sécurité.

CONSERVEZ CES INSTRUCTIONS

Mises en garde

1. Utilisez et entreposez le produit à une température entre 0° C (32°F) et 40°C (104° F).

2. N’exposez pas cet appareil à des froids ou des chaleurs extrêmes, ainsi qu’à la lumière

directe du soleil. Ne l’installez pas près d’une source de chauffage.

3. Le bloc-piles ne doit pas être exposé à la chaleur excessive telle que la

lumière du soleil ou au feu0.

4. Avertissement - Risque de strangulation - Les enfants se sont

ÉTRANGLÉS dans des cordons. Gardez ce cordon hors de portée des enfants

(à plus de 0,9 m). N’enlevez pas cette étiquette.

5. Ne jamais placer le moniteur à l’intérieur du berceau ou du parc de bébé.

Ne jamais couvrir le moniteur ou l’unité (s) portative avec un article tel une serviette

ou une couverture.

6. D’autres équipements électroniques peuvent produire des interférences sur votre

moniteur vidéo et audio. Tentez d’installer votre moniteur vidéo ou audio à l’écart des

appareils électroniques tels que des routeurs sans fil, radios, téléphones cellulaires,

interphones, moniteurs, téléphones, ordinateurs personnels, électroménagers et

téléphones sans fil.

Stimulateurs cardiaques implantés dans l’organisme

Les simulateurs cardiaques (ne s’applique qu’aux dispositifs numériques sans fil) :

L’organisme ‘Wireless Technology Research, LLC (WTR)’, une firme de recherche

indépendante, a

mené une évaluation pluridisciplinaire des interférences entre les téléphones sans fil

portatifs et les

stimulateurs cardiaques implantés dans l’organisme. Appuyée par l’Administration des

aliments et

drogues (FDA) des États-Unis, la firme WTR recommande aux médecins:

Avis aux détenteurs de stimulateurs cardiaques

• Vous devriez maintenir les dispositifs sans fil à au moins six pouces du simulateur

cardiaque.

• Ils ne doivent PAS placer le téléphone sans fil directement sur le stimulateur cardiaque,

tel que

dans une poche de chemise, lorsque celui-ci est en marche.

L’étude effectuée par l’organisme WRS n’a pas identifié de risque pour les détenteurs de

simulateurs

cardiaques causés par les gens qui utilisent dispositifs sans fil à proximité de ceux-ci.

Champs électromagnétiques (EMF)

Ce produit de LeapFrog est conforme à toutes les normes se rapportant aux champs

électromagnétiques (EMF) standard. Si vous le manipulez correctement en suivant les

instructions de ce guide, son utilisation sera sécuritaire pendant de nombreuses années,

selon les meilleures évidences scientifiques dont nous disposons aujourd’hui.

FCC and IC regulations

For cETL compliance only

Visit our Consumer Support

website 24 hours a day at:

United States:

leapfrog.com/support

Canada:

leapfrog.ca/support

Technology Wi-Fi 2.4GHz 802.11 b/g/n

Channels 1-11 (2412 - 2462 MHz)

Internet Connection Minimum Requirement: 1.5 Mbps @ 720p or 2.5 Mbps @ 1080p

upload bandwidth per camera

Nominal

effective range

Maximum power allowed by FCC and IC. Actual operating range

may vary according to environmental conditions at the time of use.

Power requirements Camera unit power adapter: Output: 5V DC @ 1A

Call our Customer Service number

from Monday to Friday

9am - 6pm Central Time:

United States & Canada:

1 (800) 717-6031

Credits:

The Background Noise sound file was created by Caroline Ford, and is used under the Creative Commons license.

The Stream Noise sound file was created by Caroline Ford, and is used under the Creative Commons license.

The Crickets At Night sound file was created by Mike Koenig, and is used under the Creative Commons license.

The Heart Beat sound file was created by Zarabadeu, and is used under the Creative Commons license.

Find the answer to your question on our knowledge-rich

Online Manual. Get assisted at your own pace and learn

what your monitor is capable of.

Scan the QR code to access the Online Manual

or visit leapfrog.com/support

Video Tutorials

Walk-throughs on features and

installation such as mounting

the Camera on the wall.

FAQs & Troubleshooting

Answers to the most commonly

asked questions, including

troubleshooting solutions.

Full Manual

Comprehensive help

articles on product set up,

operations, Wi-Fi and settings.

Online Manual

Customer Support

Please visit our

website at

leapfrog.com

for full details of the

warranty provided

in your country.

Warranty

Specifications are subject to change without notice.

a subsidiary of VTech Holdings Limited.

Technical Specifications

Note:

• Depending on surroundings and obstructing factors, such as the effect distance and internal walls

have on signal strength, you may experience reduced Wi-Fi signal.

Night Light

Want a softer hue from the camera’s night light to relax your little one? You can control the brightness

of its glow remotely from the LeapFrog Baby Care App+, or directly on the Baby Unit.

Adjust the night light on the Camera

• Tap the Night light control key located on the top of

the camera to turn on/off the night light.

Disclaimer and Limitation of Liability

LeapFrog and its suppliers assume no responsibility for any damage or loss resulting from the use of this handbook. LeapFrog and its suppliers assume no responsibility

for any loss or claims by third parties that may arise through the use of this software. LeapFrog and its suppliers assume no responsibility for any damage or loss caused

by deletion of data as a result of malfunction, dead battery, or repairs. Be sure to make backup copies of important data on other media to protect against data loss.

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE

HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED

OPERATION.

CAN ICES-3 (B)/NMB-3(B)

Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Warranty: Please visit our website at leapfrog.com for full details of the warranty provided in your country.

Notes:

• Check for reception strength and the camera viewing angle before drilling the holes.

• The types of screws and anchors you need depend on the composition of the wall. You may need to purchase the

screws and anchors separately to mount your camera.

1. Place the wall mount

bracket on a wall and

then use a pencil to mark

the top and the bottom

holes as shown. Remove

the wall mount bracket

and drill two holes in the

wall (7/32 inch drill bit).

2. If you drill the holes into a stud,

go to step 3.

• If you drill the holes into an

object other than a stud, insert

the wall anchors into the holes.

Tap gently on the ends with a

hammer until the wall anchors

are flush with the wall.

3. Insert the screws

into the holes

and tighten the

screws until

only 1/4 inch of

the screws are

exposed.

4. Place the camera on the wall mount bracket. Insert the

mounting studs into the wall mount holes. Then, slide the

camera forwards until it locks securely. Align the holes on the

wall mount bracket with the screws on the wall, and slide the

wall mount bracket down until it locks into place.

5. You can maximize your camera viewing angles

by tilting the wall mount bracket.

Hold the camera, and then rotate the knob in

an anti-clockwise direction. This will loosen the

joint of the wall mount bracket.

Tilt your camera up or down to adjust to your

preferred angle. Then, rotate the knob in a

clockwise direction to tighten the joint and

secure the angle.

Mount the Camera (Optional)

LeapFrog cares about your privacy and peace of mind. That’s why we’ve put together a list of industry-

recommended best practices to help keep your wireless connection private and your devices protected when

online.

Ensure your wireless connection is secure

• Before installing a device, ensure your router’s wireless signal is encrypted by selecting the “WPA2-PSK

with AES” setting in your router’s wireless security menu.

Change default settings

• Change your wireless router’s default wireless network name (SSID) to something unique.

• Change default passwords to unique, strong passwords. A strong password:

- Is at least 10 characters long.

- Does not contain dictionary words or personal information.

- Contains a mix of uppercase letters, lowercase letters, special characters and numbers.

Keep your devices up to date

• Download security patches from manufacturers as soon as they become available. This will ensure you

always have the latest security updates.

• If the feature is available, enable automatic updates for future releases.

Disable Universal Plug and Play (UPnP) on your router

• UPnP enabled on a router can limit the effectiveness of your firewall by allowing other network devices

to open inbound ports without any intervention or approval from you. A virus or other malware program

could use this function to compromise security for the entire network.

For more information on wireless connections and protecting your data, please review the following

resources from industry experts:

1. Federal Communications Commission: Wireless Connections and Bluetooth Security Tips –

www.fcc.gov/consumers/guides/how-protect-yourself-online

2. U.S. Department of Homeland Security: Before You Connect a New Computer to the Internet –

www.us-cert.gov/ncas/tips/ST15-003

3. Federal Trade Commission: Using IP Cameras Safely –

https://www.consumer.ftc.gov/articles/0382-using-ip-cameras-safely

4. Wi-Fi Alliance: Discover Wi-Fi Security –

http://www.wi-fi.org/discover-wi-fi/security

Protect Your Privacy and Online Security

VTech LF2911 Mode d'emploi

Marque: VTech

Modèle: LF2911

Catégorie: Moniteurs vidéo bébé

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: VTech LF2911 User guide

VTech LF2911 Mode d'emploi

VTech LF2911 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents