Rev.2 2023/08/28
User Manual
Model Name: SX-PCEAX
Since this module is not sold to general end users directly, there is no user manual of module.
For the details about this module, please refer to the specification sheet of module.
This module should be installed in the host device according to the interface specification (installation
procedure).
Spec
Rev.2 2023/08/28
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
Operations in the 5.15-5.25GHz band are restricted to indoor usage only.
This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC
Rules.
Radiation Exposure Statement:
The product comply with the FCC portable RF exposure limit set forth for an uncontrolled
environment and are safe for intended operation as described in this manual. The further RF
exposure reduction can be achieved if the product can be kept as far as possible from the user
body or set the device to lower output power if such function is available.
This module is intended for OEM integrators only. Per FCC KDB 996369 D03 OEM Manual v01
guidance, the following conditions must be strictly followed when using this certified module:
KDB 996369 D03 OEM Manual v01 rule sections:
2.2 List of applicable FCC rules
This module has been tested for compliance to FCC Part 15
2.3 Summarize the specific operational use conditions
The module is tested for standalone mobile RF exposure use condition. Any other usage
Rev.2 2023/08/28
conditions such as co-location with other transmitter(s) or being used in a portable
condition will need a separate reassessment through a class II permissive change
application or new certification.
2.4 Limited module procedures
Not applicable.
2.5 Trace antenna designs
Not applicable.
2.6 RF exposure considerations
This equipment complies with FCC mobile radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with a
minimum distance of 20cm between the radiator & your body. If the module is installed
in a portable host, a separate SAR evaluation is required to confirm compliance with
relevant FCC portable RF exposure rules.
2.7 Antennas
The following antennas have been certified for use with this module; antennas of the same
type with equal or lower gain may also be used with this module. The antenna must be
installed such that 20 cm can be maintained between the antenna and users.
Brand Model Antenna
Type
2.4GHz
Gain
5GHz
Gain
6GHz
Gain
peak Min. peak Min. peak Min.
HONGBO 260-25094
PIFA +3.53dBi
+3.53dBi
+4.81dBi
+3.06dBi
- -
HONGBO 260-25083
PIFA - - - - +5.16dBi
+5.09dBi
HONGBO 260-25084
Monopole
+3.22dBi
+3.22dBi
+4.77dBi
+3.35dBi
+4.81dBi
+4.29dBi
Taoglas GW.05.0153
Monopole
+0.37dBi
+0.37dBi
+2.43dBi
+1.69dBi
+3.09dBi
+2.48dBi
TEconnectivity
2118907-8
Monopole
+2.31dBi
+2.31dBi
+2.81dBi
+1.71dBi
+3.23dBi
+2.70dBi
2.8 Label and compliance information
The final end product must be labeled in a visible area with the following: “Contains FCC
ID: N6C-PCEAX”. The grantee's FCC ID can be used only when all FCC compliance
requirements are met.
2.9 Information on test modes and additional testing requirements
This transmitter is tested in a standalone mobile RF exposure condition and any co-located
or simultaneous transmission with other transmitter(s) or portable use will require a
separate class II permissive change re-evaluation or new certification.
2.10 Additional testing, Part 15 Subpart B disclaimer
This transmitter module is tested as a subsystem and its certification does not cover the
FCC Part 15 Subpart B (unintentional radiator) rule requirement applicable to the final
host. The final host will still need to be reassessed for compliance to this portion of rule
requirements if applicable.
Rev.2 2023/08/28
As long as all conditions above are met, further transmitter test will not be required. However,
the OEM integrator is still responsible for testing their end-product for any additional
compliance requirements required with this module installed.
IMPORTANT NOTE: In the event that these conditions can not be met (for example
certain laptop configurations or co-location with another transmitter), then the FCC
authorization is no longer considered valid and the FCC ID can not be used on the final
product. In these circumstances, the OEM integrator will be responsible for re-
evaluating the end product (including the transmitter) and obtaining a separate FCC
authorization.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the end
product which integrates this module.
The end user manual shall include all required regulatory information/warning as show
in this manual.
OEM/Host manufacturer responsibilities
OEM/Host manufacturers are ultimately responsible for the compliance of the Host and
Module. The final product must be reassessed against all the essential requirements of
the FCC rule such as FCC Part 15 Subpart B before it can be placed on the US market.
This includes reassessing the transmitter module for compliance with the Radio and
EMF essential requirements of the FCC rules. This module must not be incorporated
into any other device or system without retesting for compliance as multi-radio and
combined equipment
Prohibited for control of or communications with unmanned aircraft systems, including
drones.
Industry Canada statement:
This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes : (1) le dispositif ne doit pas produire de brouillage
préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de
provoquer un fonctionnement indésirable.
Radiation Exposure Statement:
The product comply with the Canada portable RF exposure limit set forth for an uncontrolled environment and
are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved
if the product can be kept as far as possible from the user body or set the device to lower output power if such
function is available.
Déclaration d'exposition aux radiations:
Le produit est conforme aux limites d'exposition pour les appareils portables RF pour les Etats-Unis et le Canada
établies pour un environnement non contrôlé.
Rev.2 2023/08/28
Le produit est sûr pour un fonctionnement tel que décrit dans ce manuel. La réduction aux expositions RF peut
être augmentée si l'appareil peut être conservé aussi loin que possible du corps de l'utilisateur ou que le
dispositif est réglé sur la puissance de sortie la plus faible si une telle fonction est disponible.
This device is intended only for OEM integrators under the following conditions: (For module device
use)
1) The transmitter module may not be co-located with any other transmitter or antenna.
As long as 1 conditions above are met, further transmitter test will not be required. However, the OEM
integrator is still responsible for testing their end-product for any additional compliance requirements required
with this module installed.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes: (Pour
utilisation de dispositif module)
1) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.
Tant que les 1 conditions ci-dessus sont remplies, des essais supplémentaires sur l'émetteur ne seront pas
nécessaires. Toutefois, l'intégrateur OEM est toujours responsable des essais sur son produit final pour toutes
exigences de conformité supplémentaires requis pour ce module installé.
IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or co-location with
another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be
used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the
end product (including the transmitter) and obtaining a separate Canada authorization.
NOTE IMPORTANTE:
Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines configurations
d'ordinateur portable ou de certaines co-localisation avec un autre émetteur), l'autorisation du Canada n'est
plus considéré comme valide et l'ID IC ne peut pas être utilisé sur le produit final. Dans ces circonstances,
l'intégrateur OEM sera chargé de réévaluer le produit final (y compris l'émetteur) et l'obtention d'une
autorisation distincte au Canada.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed and operated
with greater than 20cm between the antenna and users. The final end product must be labeled in a visible
area with the following: “Contains IC: 4908A-PCEAX”.
Plaque signalétique du produit final
Ce module émetteur est autorisé uniquement pour une utilisation dans un appareil où l’antenne peut être
installée et utilisée à plus de 20 cm entre l’antenne et les utilisateurs. Le produit final doit être étiqueté dans
un endroit visible avec l'inscription suivante: "Contient des IC: 4908A-PCEAX ".
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to install or
remove this RF module in the user’s manual of the end product which integrates this module.
The end user manual shall include all required regulatory information/warning as show in this manual.
Rev.2 2023/08/28
Manuel d'information à l'utilisateur final
L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final quant à la façon
d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intègre ce module.
Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et avertissements
comme indiqué dans ce manuel.
Caution :
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for
harmful interference to co-channel mobile satellite systems;
(ii) for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the bands
5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit;
(iii) for devices with detachable antenna(s), the maximum antenna gain permitted for devices in
the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits
as appropriate;
(iv) where applicable, antenna type(s), antenna models(s), and worst-case tilt angle(s) necessary to remain
compliant with the e.i.r.p. elevation mask requirement set forth in section 6.2.2.3 shall be clearly indicated.
Avertissement:
Le guide d’utilisation des dispositifs pour réseaux locaux doit inclure des instructions précises sur les
restrictions susmentionnées, notamment :
(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à
l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les
mêmes canaux;
(ii) pour les dispositifs munis d’antennes amovibles, le gain maximal d’antenne permis pour les dispositifs
utilisant les bandes de 5 250 à 5 350 MHz et de 5 470 à 5 725 MHz doit être conforme à la limite de la p.i.r.e;
(iii) pour les dispositifs munis d’antennes amovibles, le gain maximal d’antenne permis (pour les dispositifs
utilisant la bande de 5 725 à 5 850 MHz) doit être conforme à la limite de la p.i.r.e. spécifiée, selon le cas;
(iv) lorsqu’il y a lieu, les types d’antennes (s’il y en a plusieurs), les numéros de modèle de l’antenne et les
pires angles d’inclinaison nécessaires pour rester conforme à l’exigence de la p.i.r.e. applicable au masque
d’élévation, énoncée à la section 6.2.2.3, doivent être clairement indiqués
For 6G statement
a. Operation shall be limited to indoor use only; and
b. Operation on oil platforms, cars, trains, boats and aircraft shall be prohibited except for on large aircraft
flying above 10,000 ft.
a. Utilisation limitée à l’intérieur seulement;
b. Utilisation interdite à bord de plateformes de forage pétrolier, de voitures, de trains, de bateaux et d’aéronefs,
Rev.2 2023/08/28
sauf à bord d’un gros aéronef volant à plus de 10 000 pieds d’altitude.
DETACHABLE ANTENNA USAGE
This radio transmitter [IC: 4908A-PCEAX] has been approved by Innovation, Science and Economic
Development Canada to operate with the antenna types listed below, with the maximum
permissible gain indicated. Antenna types not included in this list that have a gain greater than the
maximum gain indicated for any type listed are strictly prohibited for use with this device.
Le présent émetteur radio [IC: 4908A-PCEAX] a été approuvé par Innovation, Sciences et
Développement économique Canada pour fonctionner avec les types d'antenne énumérés ci-dessous
et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le
gain est supérieur au gain maximal indiqué pour tout type figurant sur la liste, sont strictement
interdits pour l'exploitation de l'émetteur.
Antenna Type Gain Impedance
2.4GHz 5GHz 6GHz
PIFA Antenna 3.53dBi 4.81dBi 5.16dBi 50ohms
Monopole Antenna
3.22dBi 4.77dBi 4.81dBi 50ohms
The antenna-to-user separation distance must be greater than 15 mm.
La distance de séparation antenne-utilisateur doit être supérieure à 15 mm.
To ensure compliance with the Radio Frequency (RF) exposure guidelines, this device must be used at least
15 mm away from your body or nearby persons. Failure to observe this warning could result in the RF
exposure levels exceeding the applicable limits.
Pour garantir la conformité aux directives d'exposition aux radiofréquences (RF), cet appareil doit être utilisé à
au moins 15 mm de votre corps ou des personnes à proximité. Le non-respect de cet avertissement peut
entraîner des niveaux d'exposition RF dépassant les limites applicables.
The distance between each antenna should more than 50 mm when integrated in the host to ensure the
simultaneous transmission compliance.
La distance entre chaque antenne doit être supérieure à 50 mm lorsqu'elle est intégrée à l'hôte pour assurer
la conformité de la transmission simultanée.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
dans d''autres langues
- English: Silex N6C-PCEAX User manual
Documents connexes
Autres documents
-
Silex technology SX-PCEAX Manuel utilisateur
-
Silex technology SX-SDMAX Manuel utilisateur
-
Mediatek MT7922A22M Mode d'emploi
-
-
-
-
Lantronix Open-Q Mode d'emploi
-
Realtek RTL8852BE Manuel utilisateur
-
Realtek RTL8852B M.2 1216 Combo Module Manuel utilisateur
-
