Dorel Home 4673639 Assembly Manual

Questions, concerns, missing parts?

CONTACT OUR CUSTOMER SERVICE DEPARTMENT

BEFORE RETURNING PRODUCT TO THE RETAILER.

4673639 (Blue Velvet)

B34467363900-KT

Date of Purchase

Daybed with Storage

KT. - 2023/08/15

If parts are missing or damaged, we will gladly ship your

replacement parts free of charge.

Lot Number (TAKEN FROM CARTON)

Thank you for purchasing from DHP!

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY

INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.

1

Twin

Visit www.dhpfurniture.com/eng/replacement-parts

or call Toll-Free 1-800-267-1739

You can also chat with us at www.dhpfurniture.com

Weight Limit:

DayBed: 400 Lb / 181 Kg

Drawer: 40 Lb / 18 Kg

2

1-800-267-1739

DHP Consumer Services

12345 Albert Hudon, Suite 100,

Montreal, Quebec H1G 3L1

cs@dhpfurniture.com

 Work in a spacious area and near where the unit will be used, preferably on a

carpet, or use a piece of the cardboard packaging to protect your floor and product.

 Make sure all parts are included. Most parts are labeled or stamped on the raw

edge.

 Read each step carefully. It is very important that each step of the instructions is

performed in the correct order. If these steps are not followed in sequence,

assembly difficulties will occur.

 This product may contain small components. Please ensure that they are kept

away from small children.

 This product is designed for home use and is not intended for commercial use.

For help with assembly, identifying parts, product information or to order parts,

please contact us:

Limited 1 year Warranty

DHP warrants this product to be free from defects in material and workmanship

and agrees to remedy any such defect. This warranty covers one year from the

date of original purchase from authorized retailers. This is solely limited to the

repair or replacement of defective parts and assembly labor is not included.

This warranty does not apply to any product which has been improperly

assembled, subjected to misuse or abuse or which has been altered or repaired in

any way.The warranty does not cover wearing, tearing, fading or splitting of the

fabric (where applicable). Liability for consequential damages is excluded to the

extent exclusion is permitted by law. This warranty gives you specific legal rights

and you may also have other rights which vary from state to state or province to

province.

To obtain warranty service, purchaser must present original bill of sale.

Components repaired or replaced are warranted through the remainder of the

original warranty period only. The defective components will be repaired or

replaced without charge, subject to the terms and conditions described above.

The terms and conditions of the limited warranty are subject to change without

notice. For the latest warranty policy, please visit www.dhpfurniture.com.

Contact Us!

Read Before Beginning Assembly

1.5 hours

Do NOT use

powertools

This product is shipped in

1 cartons

Chat

with us! www.dhpfurniture.com

3

PARTS

M

S

L

C

Q

N

X 2

V

B

D

A

E

F

G

I

O3

Z

W

4

Each part has unique part number.

Please reference the appropriate part

number when contacting customer

service for replacement parts.

Before throwing any packaging, please

verify all contents and make sure you

have received all the parts listed above!

PARTS LIST

M

LN

QS

Drawer Side Panel

X 2

Drawer Bottom Panel

X 2

Drawer Back Panel

X 2

Drawer Side Panel

X 2

Caster

X 10

VW

Bracket

X 1

Bracket

X 1

PART NUMBERS

PART LABELS 4673639 (Blue Velvet)

B T1031810

D T1031830

L T953380

M T953390

N T953400

O3 T1031850

QT953410

S T953420

V T960450

W T960460

O3

Wooden Slats

1 PC

Armrest

X 1

Armrest

X 1

BD

5

Each part has unique part number.

Please reference the appropriate part

number when contacting customer

service for replacement parts.

Before throwing any packaging, please

verify all contents and make sure you

have received all the parts listed above!

PARTS LIST

A

Back Rest

X 1

EG

I

Rear Rail

X 1 Front Rail

X 1

Center Rail

X 1

Center Leg

X 1

F

PART NUMBERS

PART LABELS 4673639 (Blue Velvet)

A T1031800

C T1031820

E T1024760

F T1024750

G T1031840

I T960440

Z T940600

C

Front Panel

X 2

Leg

X 4

Z

6

Please do not completely tighten all the hardware,

until the entire assembly is complete, unless

otherwise indicated in the step-by-step instructions.

The screw(s), bolt(s) to be used at each step are

shown in actual size in the lower right corner of the

page.

HARDWARE LIST

Hardware Pack

HP#:T4673639-00

4673639 (Blue Velvet)

678

45

3

21

1/4" X 3/4"

Bolt(Zinc)

X 2

3/16" X 7/8"

Bolt(Zinc)

X 28

3/16" X 7/8"

Bolt(Zinc)

X 12

3/16" X 3/8"

Bolt(Zinc)

X 4

1/4''

Washer(Zinc)

X 2

4mm

Allen Key

X 1

1/4" X 1 9/16"

Bolt(Zinc)

X 6

1/4" X 1 3/16"

Bolt(Zinc)

X 8

1/4" X 3/4"

Bolt(Zinc)

X 19

9

5/16" X 1 3/4"

Bolt(Zinc)

X 4

10

7

Step 1

Attach Z x 4 to B and D with .

Screw  to B and D.

X 4

3

To avoid fraying the fabric during assembly,

please lay the part B & D on a piece of cardboard.

Z

D

B

Z

9

D

Align the edge of Z with B/D as indicated!

B D

X 8

9

Z

DD

BB

3

9

3

Do not completely tighten the

BOLTS , leave half of the thread

exposed.

B

8

Step 2

Attach V and W to A with .

X 8

A

W

V

2

Small holes on slots of V and W

should be facing upward.

AV

A

W

2

9

Step 3

Hang sub-assembly from Step 2 on D and

B as illustrated.

Don't completely tighten the

bolts  until STEP 7 is complete.

A

D

B

A

V

B

3

10

Step 4

X 4

B

D

F

2

Attach F to D and B with .

2

D

F

Slat holes on part F should be facing upward.

2

11

Step 5

Attach I to G with .

X 3

G

I

2

I

G

2

12

Step 6

Attach G to D and B with .

X 4

D

B

G

The slot hole is located on

the outside of the bed

2

G

B

G

C

F

B

E

A

E

2

13

Step 7

Attach E to A with .

X 6

A

Slat holes towards upside!

4

A

E

A

E

Velcro towards the top!

4

Then properly tighten all the bolts.

14

Step 8

SLAT WARNING

Incorrect: Slat curve

facing downwards.

Correct: Slat curve should

be facing upwards.

8.1 Insert O into X;

8.2 Press X into E, repeat the same

procedure for the opposite side with

another O & X and press into G.

8.3 Insert ends of both slats O into Y,

then press Y into F as illustrated.

X

O

X

O

E

Y

O

F

D

G

O3

8.1 Attach one end of O3 to D by inserting

the tab into the slot and turn it to the level

position.

8.2 Spread the slats O3 along the bed with

equal spacing, engage the velcro at the end

of slat with the counter part on E and G.

E

G

D

B

O3

O3O3O3

D

8.1

8.2

15

Step 9

Attach the other end of O3 to B by inserting

the tab into the slot and turn it to the level

position.

O3

B

O3

B

D

O3

G

E

16

Step 10

Attach M to N and S with.

Don't completely tighten the

bolts until STEP 12 is complete.

6

X 8

X 2

Make sure that these holes are all located

on the top side before assembling!

S

N

M

For better performance, please orient the

plastic sheet towards inside of the drawer.

6

17

Step 11

Attach Q to L with .

5

Q

L

X 2

5

X 4

5

18

Step 12

Q

L

Q

M

N

S

7

X 4 X 16

12.1 12.2

X 2

7

Q

L

S

6

L

M

12.1 Attach Q X 4 and L to S and N with .

12.2 Attach L to M with .

6

7

6

19

Step 13

C

7

Attach sub-assembly N/L/S/M from

previous step to C with , then properly

tighten all the bolts.

X 12

X 2

S

M

N

L

7

20

Step 14

C

1

8

Attach  and  to C.

X 2 X 2

X 2

C

8

1

18

La page charge ...

Dorel Home 4673639 Assembly Manual

Dorel Home 4673639 Assembly Manual

dans d''autres langues

Documents connexes

Autres documents