Mettler Toledo EasyClean200e cleaning and calibration system Mode d'emploi

EasyClean 200e

30 404 676 F

EasyClean 200e

Instruction manual

Bedienungsanleitung

Instructions d’utilisation

English: page 3

Deutsch: Seite 43

Français: page 83

EasyClean 200e 3

EasyClean 200e 02/2021 © METTLER TOLEDO

30 404 676 F Printed in Switzerland

EasyClean 200e

Instruction manual

4 EasyClean 200e

02/2021 © METTLER TOLEDO EasyClean 200e

Printed in Switzerland 30 404 676 F

How to use this instruction manual

This instruction manual is an integral part of the EasyClean 200e and contains notes

and instructions that are important for safety and operation.

All persons working on or with the EasyClean 200e must have first read and understood

the sections appropriate to the work in hand.

Please read this instruction manual carefully before using the EasyClean system. Keep this

document close to the unit, so operating personnel may be easily refer to it at any time.

First read section 2 “Safety”!

No part of this manual may be reproduced in any form, or modified, copied or distributed using electronic systems,

in particular in the form of photocopies, photographs, magnetic or other recordings, without written consent of

Mettler-Toledo GmbH, Process Analytics, CH-8902 Urdorf.

EasyClean is a trademark of the METTLER TOLEDO Group.

InDip is a registered trademark of the METTLER TOLEDO Group in Switzerland, Brazil, Belgium, Netherlands,

Luxembourg, Germany, France and Italy.

InTrac is a registered trademark of the METTLER TOLEDO Group in Switzerland, Brazil, UK, USA, Austria, Belgium,

Netherlands, Luxembourg, Germany, France, Italy and Russia.

EasyClean 200e 5

EasyClean 200e 02/2021 © METTLER TOLEDO

30 404 676 F Printed in Switzerland

Content

How to use this instruction manual 4

1 Product description 7

1.1 Introduction 7

1.2 Fittings and deliverables 7

1.3 Data and key characteristics EasyClean 200 e 8

2 Safety 10

2.1 Introduction 10

2.2 Intended use 10

2.3 Inappropriate use 10

2.4 Basic principles 11

2.5 Warning notices and symbols 11

2.6 Responsibility, organizational measures 12

2.7 Product-specific hazards 13

2.8 Residual hazards 13

2.9 Emergency measures 13

2.10 Safety measures 14

2.11 Modifications 14

3 Your device 15

3.1 Layout 15

3.2 Functions 17

3.3 Integration into a measurement system 18

4 Commissioning 19

4.1 Fitting 19

4.2 Connections 21

4.3 Commissioning procedure 28

4.4 Function test 29

4.5 Programming of control of EasyClean 200 e 30

4.5.1 User interface of the programmable control 30

4.5.2 SW parameter description 31

5 Operation 33

5.1 Checks by the operator 33

5.2 Refilling with cleaning fluid 33

5.3 Operating the EasyClean 200 e 33

5.4 Procedure in the event of a failure in the power or fuel supply 35

6 Maintenance and fault elimination 36

6.1 Maintenance 36

6.2 Fault elimination and repairs 36

7 Decommissioning, storage, disposal 39

7.1 Decommissioning 39

7.2 Storage 39

7.3 Correct disposal of the unit 39

8 Ordering information (product, spare parts, accessories) 40

8.1 Ordering information for EasyClean 200 e 40

6 EasyClean 200e

02/2021 © METTLER TOLEDO EasyClean 200e

Printed in Switzerland 30 404 676 F

EasyClean 200e 7

EasyClean 200e 02/2021 © METTLER TOLEDO

30 404 676 F Printed in Switzerland

1 Product description

1.1 Introduction

C

ertificates CE

I

dentification

1.2 Fittings and deliverables

Deliverables EasyClean 200e is shipped without connecting cables. At the installation site, cables are

connected to the appropriate terminals in the unit (please refer to section 4.2 “Connections”).

Packaging The unit is packed in plain and padded cardboard.

We recommend that you retain the packing materials for subsequent storage or transportation

of the unit. Should you choose to discard the packing materials, observe local regulations and

section 7.3 “Correct disposal of the unit”.

Good inspection Check the goods for damage while unpacking. Should you notice signs of damage,

inform the shipper and your supplier without delay.

Check the delivery against your order and the delivery note.

w

ww.mt.com/pro

M

ettler-Toledo GmbH

I

m Hackacker 15

8

902 Urdorf

S

witzerland

S

/N: 1234567890

P/N: 52403776

M

ODEL: EasyClean 200e

PWR: 100 - 230VAC 50/60Hz,

0.18 - 0.3A

M

ETTLER TOLEDO

w

0.18 - 0.3A

15

8 EasyClean 200e

02/2021 © METTLER TOLEDO EasyClean 200e

Printed in Switzerland 30 404 676 F

1.3 Data and key characteristics EasyClean 200e

Enclosure Stainless steel enclosure, powder-coated with polyester resin

Attention: housing may not be cleaned with solvents

containing acetone

Weight Control unit approx. 3.0 kg (6.6 lb)

Valve unit approx. 2.5 kg (5.5 lb)

Protection rating IP65

Ambient conditions Temp. in operation: 0…+55°C (+32…+131°F)

Temp. storage/transportation: –10…+70°C (+14…+158°F)

Power supply 100…230V AC, 50/60 Hz, 0.18…0.3 A (± 15%)

System control Process initiation:

via a wash contact in the associated transmitter

Sequence:

controlled by the integrated programable PLC

Control input 1 control input for wash contact in transmitter 24V

Transmitter METTLER TOLEDO transmitters:

– M300 Process

– M400 4-wire

– Alternatively via any standard transmitter with wash

contact and “HOLD” function

Electrical connections Terminal strip 0.08…2.5 mm

2

Connection to valve unit 10-wire control cable, 1.5 mm

2

Length: 1.5 m

Connection transmitter 4-wire control cable, 43 1.5 mm

2

Length: 5 m

Cable ducts ∆ 3.5…10 mm Æ M16

∆ 2.5…6.5 mm Æ M12

Compressed air supply 4…8 bar (400…800 kPa, 58…116 psi)

– Air quality according to ISO 8573-1

– Moisture class 4 (water dew point +3°C)

– Particles class 5 (filter 40 µm)

– Max. oil content class 2 (0.1 mg/m

3

)

Connection: thread G

1

/8"

EasyClean 200e 9

EasyClean 200e 02/2021 © METTLER TOLEDO

30 404 676 F Printed in Switzerland

Connection to Pneumatics: LDPE hose ∆ 6/4 mm (

1

/4"/

1

/8")

retractable housing (control air)

Medium: PTFE hose ∆ 6/4 mm (

1

/4"/

1

/8")

Hose length typ. 5 m (16.4 ft)

Hose length max. 10 m (32.8 ft)

Flushing water supply Pressure: 2…8 bar (200…800 kPa, 29…116 psi)

Particle filter: 50 µm

Volume: $4 l/min

Connection: thread G

1

/4" female

Adapter:

1

/4" NPT male (PP)

Pump Pump height: max. 5 m (16.4 ft)

Suction height: max. 3 m (9.8 ft)

Feed rate: 3…5 ml/s (depending on hose length

and medium viscosity)

Materials: PPS (pump body)

EPDM (membrane and sealings)

Connection: thread G

1

/8" female, polymer (PP)

Viscosity All liquids 25 mPa s/25°C (77°F)

Wetted materials Materials in contact with:

– Rinsing water: PP, EPDM, PFTE, PPS, Ni

– Compressed air: PP, EPDM, PFTE, PPS, LDPU, Ni

– Cleaning agents: PP, FFKM, PTFE, EPDM, PEEK

Liquid temperatures Water: 0…80°C, 95°C max. 10 min/h

(32…176°F, 203°F max. 10 min/h)

Cleaning agents: 0…50°C (32…122°F)

Subject to technical changes.

10 EasyClean 200e

02/2021 © METTLER TOLEDO EasyClean 200e

Printed in Switzerland 30 404 676 F

2 Safety

2.1 Introduction

This instruction manual lists the main points of how to use the EasyClean 200e efficiently,

in the intended manner. For safe, trouble-free operation, operators must be aware of these safety

instructions and comply with further warning notices in the instruction manual.

This instruction manual, and the safety requirements in particular, must be observed by the

operator and all other persons working with the EasyClean 200e. Compliance with local

regulations and statutory requirements is also essential.

The instruction manual must always be stored close at hand, in a place accessible to all

people working with the EasyClean 200e.

2.2 Intended use

EasyClean 200e is intended solely for automatically controlled or manual flushing and cleaning

of sensors in retractable housings, as described in this instruction manual.

Other prerequisites for appropriate use include:

– observing the instructions, notes and requirements set out in this instruction manual

– observing the prescribed inspection and maintenance intervals

– correct care and maintenance of the unit, according to the instruction manual

– observing the prescribed environmental and operational conditions, and permitted

installation positions

– compliance with local statutes.

2.3 Inappropriate use

Any other use, or use not mentioned here, that is incompatible with the technical specifications

is deemed inappropriate. The operator is solely responsible for any damage arising from such

use.

The following are deemed particularly inappropriate:

– use of hydraulic fluid in place of compressed air

– use of suspensions as cleaning media

– use of salt acid of > 10%.

EasyClean 200e 11

EasyClean 200e 02/2021 © METTLER TOLEDO

30 404 676 F Printed in Switzerland

2.4 Basic principles

The EasyClean system is a state-of-the-art construction and complies with engineering safety

g

uidelines.

All the same, there can remain certain risks and hazards:

– if the units are operated by inadequately trained personnel.

–

if the units are not used in the intended manner.

– if the units are not inspected periodically or the periodical inspection

is not carried out properly.

EasyClean units must only be used while in perfect working order, for their intended purpose,

with due awareness of associated safety and hazard issues and in compliance with the

instruction manual.

Defects or damage that impact the unit’s safety and functionality must be immediately repaired

by the operator or a suitably qualified person, and reported in writing to the manufacturer.

2.5 Warning notices and symbols

This instruction manual identifies safety instructions by means of the following symbols:

DANGER

Warns of a hazard that could lead to extensive material damage, death or grievous bodily

injuries.

CAUTION

Warns of a potentially hazardous situation that could lead to minor bodily injury and/

or material damage.

NOTICE

Information relating to technical requirements. Non-observance could lead to defects,

inefficient operation and possible loss of production.

12 EasyClean 200e

02/2021 © METTLER TOLEDO EasyClean 200e

Printed in Switzerland 30 404 676 F

2.6 Responsibility, organizational measures

Operator’s

responsibilities

– The operator must only permit personnel to work with the EasyClean if they are acquainted

with basic regulations concerning workplace safety and accident prevention, and familiar

with operating the unit. This instruction manual serves as a basis.

– In addition to the instruction manual, the operator must provide instruction in general statu-

tory and other binding regulations concerning workplace safety and accident prevention,

as well as environmental protection.

– Personnel safety and hazard awareness must be monitored regularly.

– Steps must be taken to ensure that the EasyClean is operated only while in a safe, properly

functional state.

Personnel

responsibilities

– All persons working with the EasyClean must have read the section on safety and respon -

sibilities the warning notices contained in this instruction manual.

– In addition to the instruction manual, generally applicable statutory and other binding

regulations concerning workplace safety and accident protection must also be observed.

– Avoid any hazardous working practices that exceed the unit’s intended purpose.

Personnel selection and

qualification

– basic responsibilities

– Only dependable, trained or supervised personnel may work with the EasyClean.

Operators must read this instruction manual beforehand.

– Responsibilities for operating, maintaining, installing, etc. the unit must be clearly defined.

– Appropriate steps must be taken to ensure that the unit is used by authorized personnel only.

– Personnel under instruction, supervision or general training may only work with the unit

under constant supervision by an experienced person.

– Work on electrical parts of the unit may only be performed by a qualified electrician in

compliance with electrical engineering regulations.

Constructional

modifications on the unit

– The unit may not be modified, extended or rebuilt in a way that impacts its safety without

written permission from Mettler-Toledo GmbH, Process Analytics.

– Any parts that are not in perfect working order must be replaced without delay.

EasyClean 200e 13

EasyClean 200e 02/2021 © METTLER TOLEDO

30 404 676 F Printed in Switzerland

2.7 Product-specific hazards

D

ANGER

Electrical hazards!

O

pening the unit for installation or repair work exposes live electrical parts.

C

lose the unit immediately after work is completed!

DANGER

Compressed air/water hazards!

Pressurized pipes (compressed air, water) must be isolated and depressurized before

commencing repair work!

2.8 Residual hazards

DANGER

Despite all precautionary measures, there remain residual hazards such as:

– a pipe bursting

– hazards arising from a defect in a supervisory controller.

2.9 Emergency measures

DANGER

Should fluid come into contact with the eyes, rinse thoroughly under running water

for at least 15 minutes. A doctor must be consulted for subsequent diagnosis.

Fluid coming into contact with the skin must be immediately washed away with water.

Medical assistance is mandatory for symptoms that clearly arise from skin or eye

contact with a medium. Inform the doctor about the type and specific identity of all

materials used.

14 EasyClean 200e

02/2021 © METTLER TOLEDO EasyClean 200e

Printed in Switzerland 30 404 676 F

2.10 Safety measures

Always observe local statutes and regulations. They are not incorporated in this instruction

manual.

Personal safety equipment like protective goggles and clothing must be worn.

T

he unit must only be operated while closed.

The operator is responsible for personnel instruction. By way of assistance, the instruction

manual can also be ordered in other languages. Being an integral part of the unit, this instruc-

tion manual must always be available at the unit’s location.

The operator should immediately inform the manufacturer about all safety-related events

occurring during use of the unit.

2.11 Modifications

Modifications are permitted only after prior consultation and written approval from the

manufacturer.

Only those parts of the unit essential to fulfilling its function may be removed and refitted.

Except for authorized service personnel, it is forbidden to remove protective guards and

covers using a regular tool. Touching live electrical parts represents a lethal hazard.

EasyClean 200e 15

EasyClean 200e 02/2021 © METTLER TOLEDO

30 404 676 F Printed in Switzerland

3 Your device

3.1 Layout

Control unit

1 “In/Out” button (housing control)

2 “Water” button

3 “Clean” button

4 Information display

5 Power supply unit

E

asyClean 200e

6 Programmable logic controller

7 Operating section PLC

8 Connection clamps

9 Remote PCB

1 2 3

4

5 6 7

9

8

16 EasyClean 200e

02/2021 © METTLER TOLEDO EasyClean 200e

Printed in Switzerland 30 404 676 F

V

alve unit (figure shows valve unit EasyClean 200e)

1 Compressed air valve

2 Water valve

3 Pressure reducing valve

4 Detergent valve

5 Housing control valve

6 Diaphramgm pump

6

1 2 3 4 5

EasyClean 200e 17

EasyClean 200e 02/2021 © METTLER TOLEDO

30 404 676 F Printed in Switzerland

3.2 Functions

General The EasyClean 200e is designed for the automatic rinsing and cleaning of electrodes in

r

etract able housings.

The EasyClean is supplied with a predefined rinsing and cleaning process. Both the rinsing

and cleaning time can be adjusted by the operator to suit the individual local conditions.

The individual processes are instigated by switching on the washing contact on the connected

transmitter.

An integrated programmable logic controller controls the whole rinsing and cleaning procedure.

Types of operation The EasyClean has no main switch, and is always in active status.

Basic setting When the EasyClean 200e is switched off, the electrode is removed from the process medium.

If the EasyClean 200e is connected to the mains, the housing and sensor move into

the measuring position.

The message “RUN” appears on the display. The EasyClean is ready for operation.

“HOLD” function The “HOLD” function is a function of the transmitter. This function suppresses the measured

values of the sensor during a work cycle of the EasyClean.

NOTICE

If the transmitter is usually used with exit points, a “HOLD” function is absolutely necessary.

Signals that can be measured through cleaning with acids or alkalis might otherwise activate

the transmitter control.

Messages

The integrated control is equipped with a display.

This displays the current function status of the control.

18 EasyClean 200e

Printed in Switzerland 30 404 676 F

3.3 Integration into a measurement system

T

he following diagram show typical examples of the integration of the EasyClean 200e

respectively into a measurement system.

EasyClean 200e

1 Control unit

2 Valve unit

3 Connection cable control unit > valve unit

4 Water connection

5 Drainwater hose

6 Connecting hose valve unit > cleaning medium

7 Connecting hose valve unit > retractable housing

8 Wall mounting kit

9 Compressed air hose inlet

10 Compressed air hoses

11 Control cable transmitter > control unit

12 Pneumatic set retractable housing

13 Panic button (optional)

14 Canister for cleaning medium

15 Remote control

16 Alarm light

11

16

1

3

8

1

5

9

4

2

10

7

5

12

6

14

Panic button

«Panik»-Knopf

Bouton «anti-panique»

10 0 – 230 VA C

20 – 2 53 VAC

EasyClean 200e 19

30 404 676 F Printed in Switzerland

DANGER

Please refer to section 2 “Safety”.

All work on the system’s electrical components may only be performed by authorized,

s

pecialist staff.

4.1 Fitting

The EasyClean 200e is designed to be fitted directly (c-rails), on to walls or posts/pipes.

The EasyClean 200e is built into the same type of housing and therefore have the

same dimensions.

The fitting location must have sufficient stability and must as far as possible be free of vibration.

Please make sure that the lengths of the leads are as short as possible.

4 Commissioning

Wall mounting

20 EasyClean 200e

Printed in Switzerland 30 404 676 F

Post/pipe mounting

NOTICE

For the detailed procedure when fitting the suspended item, please refer to the installation

manual supplied separately.

La page charge ...

Mettler Toledo EasyClean200e cleaning and calibration system Mode d'emploi

Mettler Toledo EasyClean200e cleaning and calibration system Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents