Samsung SCC-B1391P Manuel utilisateur

User’s Manual

DIGITAL COLOR CAMERA

E

D

F

Sp

I

Pl

R

SCC-B1391(P)

SCC-B1091P

(AB68-00512B)SCC-B1391-01Eng 2005.6.17 4:7 PM ˘`1

E

Important Safety Instructions

CAUTION: TO REDUCE THE

RISK OF ELECTRIC SHOCK,

DO NOT REMOVE REAR

COVER. NO USER

SERVICEABLE PARTS INSIDE.

REFER TO QUALIFIED

SERVICE PERSONNEL.

To prevent damage which may result in fire or electric shock hazard,

do not expose this appliance to rain or moisture.

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions.

1) This device may not cause harmful interference, and

2) This device must accept any interference that may cause undesired

operation.

CAUTION:

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the

manufacturer.

Dispose of used batteries according to the manufacturer’s instructions.

This symbol indicates

high voltage is present

inside. It is dangerous to

make any kind of contact

with any inside part of this

product.

This symbol alerts you

that important literature

concerning operation and

maintenance has been

included with this product.

CAUTION

RISK OF ELECTRIC

SHOCK DO NOT OPEN

2

(AB68-00512B)SCC-B1391-01Eng 2005.6.17 4:7 PM ˘ `2

3

E

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance

with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat

registers, or other apparatus (including amplifiers) that produce

heat.

9. Do not defeat the safety purpose of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than

the other. A grounding type plug has two blades and a third

grounding prong. The wide blade or the third prong are provided

for your safety. If the provided plug does not fit into your outlet,

consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being from being walked on or

pinched particularly at plugs, convenience receptacles, and the

point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with cart, stand, tripod, bracket, or table specified by

the manufacturer, or sold with the apparatus. When a used,

caution when moving the cart/apparatus combination to avoid

injury from tip-over.

13. Unplug this apparatus. When a cart is used, use caution when

moving the cart/apparatus combination to avoid injury from tip-

over.

14. Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged, liquid has been

spilled or objects have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does not operate

normally, or been dropped.

(AB68-00512B)SCC-B1391-01Eng 2005.6.17 4:7 PM ˘ `3

4

E

Chapter 1 Introduction ........................................................ 5

Chapter 2 Special Features ............................................. 6

Chapter 3 Installation ......................................................... 7

Checking the contents of the package .............. 7

Precautions in Installation and Use ................... 8

Connecting Auto Iris Lens Connector ................ 9

Lens Fixing

........................................................... 10

Setting Lens Selection Switch

.................... 11

Back Focus Adjustment

................................ 11

Connecting Cables and Checking Operation ..... 13

Chapter 4 Part Names and Functions ............................... 15

Product Specification ........................................ 20

Contents

(AB68-00512B)SCC-B1391-01Eng 2005.6.17 4:7 PM ˘ `4

5

E

This camera is the high-resolution monitoring camera of 540 TV Lines and can

provide the best monitoring function by connecting with the CCTV System.

❉

In the mechanical fluorescent light environment, if you attach MANUAL IRIS

LENS and turn the ELC switch among FUNCTION switches on, color may be

rolled.

In this case, supply AC power before you turn L/L switch among FUNCTION

switches on. (NTSC:60HZ , PAL:50HZ)

Chapter 1 Introduction

COLOR ROLLING is the problem that color on the

monitor screen changes non-periodically.

This happens when White Balance is not fixed,

because a mechanical fluorescent light flickers

when it’s cycle is the same to the cycle of the power

frequency.

(AB68-00512B)SCC-B1391-01Eng 2005.6.17 4:7 PM ˘ `5

6

E

High Sensitivity

It has an up-to-date 1/3" Super-HAD IT CCD for an image of high sensitivity.

Resolution

It realizes high resolution resulting from full digital image processing

supported by a state-of-art digital signal technology.

Superior Back Light Adjustment Function

In case the object has a bright illumination or sunlight behind it, this camera

adjusts the image shaded by the back light for clear photographs.

Digital Power Supply Synchronization Method

The Full Digital Method Line Lock is realized in this camera, which adjusts

the vertical camera synchronization directly to improve controllability and

reliability of the camera.

Chapter 2 Special Features

(AB68-00512B)SCC-B1391-01Eng 2005.6.17 4:7 PM ˘ `6

7

E

This chapter describes what should be checked before installation, how to

set the installation environment, and what should be done during installation.

Then, it describes how to install the camera and connect the cable in actual

circumstances.

Chapter 3 Installation

Be sure to check if the following items are included in the package.

Checking the contents of the package

Camera

Holder(Mount)

C Mount Adapter

Auto Iris

Lens Connector

User's Manual

Camera

(AB68-00512B)SCC-B1391-01Eng 2005.6.17 4:7 PM ˘ `7

8

E

① Do not attempt to disassemble the camera yourself.

➁ Be cautious in handling the camera. Avoid striking or shaking the

camera. Be cautious to avoid damage on the camera caused by improper

storage or operation.

➂ Do not expose this camera to rain or moisture. Do not operate this

camera on a wet place.

➃ Do not use strong or abrasive detergents when cleaning the camera

body. Use a dry cloth to clean the camera.

⑤ Keep the camera at a cool place away from the direct sunlight. Leaving it

under the direct sunlight may result in the malfunction of the unit.

Precautions in Installation and Use

(AB68-00512B)SCC-B1391-01Eng 2005.6.17 4:7 PM ˘ `8

9

E

Connecting Auto Iris Lens Connector

Prepare the following Auto Iris Lens Connector supplied with the camera.

Connect the cable of the control cable, whose covering is stripped, to the

Auto Iris Lens Connector as shown below.

Rb

Pin3

Pin2

Pin4

Pin1

Pin No. DC Control Type VIDEO Control Type

1 Damp(-) Power (+12V)

2 Damp(+) N/A

3 Drive(+) VIDEO Signal

4 Drive(-) GROUND

(AB68-00512B)SCC-B1391-01Eng 2005.6.17 4:7 PM ˘ `9

In case of CS lenses

Turn the CS lens clockwise until it is fixed as shown as follows.

In case of C lenses

Turn the C-mount adapter clockwise to fix it. Then turn the C lens

clockwise until it is fixed as follows.

Lens Fixing

CS lens

C lens

10

E

(AB68-00512B)SCC-B1391-01Eng 2005.6.17 4:7 PM ˘ `10

Back Focus Adjustment

Setting Lens Selection Switch

11

E

The camera back focus is adjusted at the plant before delivery, but some

lenses are out of focus though the number differs in types. If it's the case,

you should make the back focus adjustment as follows. First, this is the back

focus adjustment procedure for fixed focus lenses.

Lenses without zoom function

① Image an object with high resolution(letticed) at more than 10m distance

and put the lens focus ring in the infinite(

∞

) position.

➁ Rotate the BACK FOCUS control bar until the object is seen best.

➂ Tighten the BACK FOCUS control bar fixing screw.

When lens mounting is completed, set the Lens selection Switch on the side

of the camera according to the mounted lens type. When the mounted lens

is an Auto Iris Lens of the DC control type, set the Lens Selection Switch to

"DC". When the mounted lens is an Auto Iris Lens of the Video control type,

set the Lens Selection Switch to "VIDEO".

(AB68-00512B)SCC-B1391-01Eng 2005.6.17 4:7 PM ˘ `11

12

E

Lenses with zoom function

① Image an object with high resolution(letticed) at a distance of 3 to 5 m

and zoom in the lens as close to TELE as possible. Then adjust the lens

focus bar until the object is seen best.

➁ Zoom in the lens as close to WIDE as possible and adjust the BACK

FOCUS adjustment bar until the object is seen best.

➂ Repeat from ① to ➁ above 2 or 3 times until the focus on the ZOOM

TELE side is in line with that on the ZOOM WIDE side.

BACK FOCUS

CONTROL BAR

(AB68-00512B)SCC-B1391-01Eng 2005.6.17 4:7 PM ˘ `12

Connecting Cables and Checking Operation

13

E

1 First, connect the connector of the BNC cable to the Video Out terminal

2 Second, connect the other connector of the BNC cable to the Video In

terminal.

BNC cable

Video Out Terminal

Video In Terminal of

Monitor Rear Surface

(AB68-00512B)SCC-B1391-01Eng 2005.6.17 4:7 PM ˘ `13

14

E

3 Third, connect the power cable.

① AC24V/DC12V Power Input Camera.

Connect 2 lines of the power adapter using a screwdriver to the power

IN Terminal of the camera as shown below.

❉

Without the distinction of the polarity, connect to the AC24 or DC12V

power source.

➁ AC230V Power Input Camera

Connect the power input cord to the AC230V power source.

(AB68-00512B)SCC-B1391-01Eng 2005.6.17 4:7 PM ˘ `14

15

E

Chapter 4 Part Names and Functions

Side View

①

Mount Adapter Fixing Groove

This groove is used for screwing the mount adapter, a part of the bracket where the

camera will be installed.

➁

Camera Lens(Option)

This lens is installed in the camera.

❉

A camera lens with a stained surface should be cleaned softly with a lens

tissue or ethanol painted cotton cloth.

➂

Auto Iris Lens Connector

This connector provides the automatic shutter lens with power supply, control signal,

video signal, or DC signal necessary for the control of the lens shutter.

➃

Auto Iris Lens Control Cable

This cable transmits signal which controls the Iris.

⑤

ALC Lens Selection Switch

This Switch is used for select the type of Lens.

➅

Back Focus Control Bar

This bar is used for set back focus of the camera.

➃

Auto Iris Lens

Control Cable

⑤

ALC Lens

Selection Switch

➂

Auto Iris Lens

Connector

①

Mount Adapter Fixing

Groove

➅

Back Focus

Control Bar

➁

Camera Lens

(AB68-00512B)SCC-B1391-01Eng 2005.6.17 4:7 PM ˘ `15

Rear View

16

E

AC24V/DC12V Camera (SCC-B1391(P))

AC230V Camera (SCC-1091P)

⑤

➁

➅

⑦

①

➂ ➃

⑤

①

➂ ➃

⑦

➁

➅

(AB68-00512B)SCC-B1391-01Eng 2005.6.17 4:7 PM ˘ `16

17

E

① Power connection port

AC24V/DC12V Camera : It is a port connected to the power adaptor cable.

AC230V Camera : It is Power cord.

➁ POWER LED

If the power of a camera is supplied normally, the LED is ON.

➂➃INC and DEC Switch

Both switches increase or decrease the profit of RED and BLUE to fix a color

temperature as you wish while AWB among the FUNCTION switches is

off(USER) and control the vertical synchronous phase while both AWB and

L/L are on.

⑤ FUNCTION Switch

1. L/L 2. ELC

3. FL 4. AWB

SW1 SW2 SW3 SW4

ON

(AB68-00512B)SCC-B1391-01Eng 2005.6.17 4:7 PM ˘ `17

18

E

1) SW1(L/L) :

Set to OFF, the camera activates the internal synchronization mode and set to ON, the power

synchronization mode. If you connect multi cameras to the sequential switcher to enter the

automatic conversion mode, the screen will bounce every screen while the camera stays in

INT(internal synchronization). Such bouncing phenomena may be cleared and screen conversion

becomes smooth by setting the L/L switch to ON and using the INT/DEC switch to control the

vertical synchronous phase.

❉

If you want to control the vertical synchronous phase with the INT/DEC switch when L/L is set

to ON, you shall set SW4 to AWB ON.

❉

In case of DC12V, INT(internal synchronizer) will be fixed without regard to ON/OFF of L/L.

2) SW2(ELC) :

Use this switch with the Manual Iris Lens. While this switch is ON, the speed of the electronic

shutter varies with the brightness of the subject from 1/60(50) to 1/100,000 sec for automatically

controlling the brightness of the screen. However, with the Auto Iris Lens (DC or Video Control),

be sure to switch OFF.

Color Rolling may occur in this mode. In that case, input AC power source to the camera and

select SW1 "ON".

(NTSC : 60HZ, PAL : 50HZ)

3) SW3(FL):

This is to prevent flicker on the screen when NTSC system is used in 50HZ power supply region

and PAL system is used in 60HZ power supply region. That is to prevent shaking on the

screen resulted from the discordance of the vertical sync frequency and the flicker frequency of

the illumination. While this switch is ON, the electronic shutter is fixed to 1/100sec (NTSC) or

1/120 sec (PAL).

4) SW4(AWB):

When setting up ON, the color of screen is adjusted automatically in accordance with the change

of lighting color temperature by the change of outer environment. (ATW) If the lighting condition is

steady, OFF setting is available. The camera memorizes the lighting color temperature at the

time when the switch setting is changed from ON to OFF, and the camera color is adjusted to the

memorized color temperature. (AWC) If the lighting color temperature is changed and you want

to make the camera be memorized/operated with the changed color temperature, re-operate the

switch On/Off operation. However, be aware that an error may occur under the following

conditions.

First, a case that the subject is big, single color of the high chroma, and in the center of

the screen or a case with almost no white color on the screen.

Second, a case with a specific illumination such as a natrium lamp

(AB68-00512B)SCC-B1391-01Eng 2005.6.17 4:7 PM ˘ `18

19

E

➅

DC IRIS Level Controller

When the ALC lens selection switch is set to DC, use the same control bar as the

driver to control the IRIS level.

⑦

Video Output Port

This port shall be connected to the monitor video input port or equivalent. You

may output camera video signals through this port.

(AB68-00512B)SCC-B1391-01Eng 2005.6.17 4:7 PM ˘ `19

20

E

Product Specification

SCC-B1391P/B1091P

ITEM

Contents

Product Type CCTV Camera

Broadcasting System PAL STANDARD SYSTEM

CCD 1/3 Super-HAD CCD

Effective Pixels 752(H) x 582(V)

Scanning Type 625 Line, 2:1 Interlace

INTERNAL : 15,625Hz(H)

50 Hz(V)

LINE LOCK : 15,625Hz(H)

50 Hz(V)

INTERNAL

LINE LOCK(When AC Power source is used)

Resolution(H) 540 TV Lines

S/N Ratio About 50dB

Frequency

Sync Type

Minimum Illumination

of Object

0.3 Lux

(AB68-00512B)SCC-B1391-01Eng 2005.6.17 4:7 PM ˘ `20

La page charge ...

Samsung SCC-B1391P Manuel utilisateur

Samsung SCC-B1391P Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents