Maytag MDG20PNAGW Installation Instructions Manual

www.maytagcommerciallaundry.com

W10868681B

INSTALLATION INSTRUCTIONS

Original instructiOns

cOmmercial gas Or electric Dryer

mODels

mDe20PDagW, mDe20PnagW, mDe20mnagW, mDe20csagW,

mDg20PDagW, mDg20PnagW, mDg20mnagW, anD mDg20csagW

INSTRUCTIONS D’INSTALLATION

instructiOns D’Origine

sèche-linge À gaz Ou Électrique À usage cOmmercial

mODèles

mDe20PDagW, mDe20PnagW, mDe20mnagW, mDe20csagW,

mDg20PDagW, mDg20PnagW, mDg20mnagW, anD mDg20csagW

INSTRUCCIONES DE INSTALACIÓN

instrucciOnes Originales

secaDOra a gas O elÉctrica cOmerciale

mODelOs

mDe20PDagW, mDe20PnagW, mDe20mnagW, mDe20csagW,

mDg20PDagW, mDg20PnagW, mDg20mnagW, anD mDg20csagW

ISTRUZIONI D’INSTALLAZIONE

istruziOni Originali

asciugatrice a gas O elettrica cOmmerciale

mODelli

mDe20PDagW, mDe20PnagW, mDe20mnagW, mDe20csagW,

mDg20PDagW, mDg20PnagW, mDg20mnagW, anD mDg20csagW

2

TABLE OF CONTENTS

DRYER SAFETY ................................................................................ 3

FOR THE OWNER

MAINTENANCE INSTRUCTIONS ..................................................6

IF YOU NEED ASSISTANCE .........................................................6

FOR WHIRLPOOL AUTHORIZED SERVICE PERSON

TOOLS & PARTS ..............................................................................7

SPECIFICATIONS ............................................................................ 7

DIMENSIONS/CLEARANCES .................................................... 8

DRYER INSTALLATION REQUIREMENTS ............................... 9

INSTALLING LEVELING LEGS AND COIN BOX ..................... 10

LEVELING ........................................................................................ 11

ELECTRIC DRYER INSTALLATION REQUIREMENTS ........ 12

GAS DRYER INSTALLATION REQUIREMENTS ................... 13

DRYER VENTING REQUIREMENTS ....................................... 15

GAS SUPPLY CONNECTION .................................................... 17

TECHNICAL SPECIFICATIONS–GAS DRYER ....................... 18

COMPLETE INSTALLATION ....................................................... 20

REVERSING DRYER DOOR SWING ........................................ 21

ELECTRONIC CONTROL SETUP INSTRUCTIONS

(PD & PN MODELS) ..................................................................... 22

DRYER DISPOSAL ........................................................................ 27

WARRANTY ................................................................................... 28

TABLE DE MATIÈRES

SÉCURITÉ DE LE SECHE-LINGE ................................................29

POUR LE PROPRIÉTAIRE

INSTRUCTIONS D’ENTRETIEN .................................................. 32

SI VOUS AVEZ BESOIN D'ASSISTANCE ................................ 31

POUR LE PERSONNEL D’ENTRETIEN AUTORISÉ

PAR WHIRLPOOL

OUTILS ET PIÈCES ....................................................................... 33

SPÉCIFICATIONS .......................................................................... 33

DIMENSIONS/DÉGAGEMENT ................................................... 34

EXIGENCES D’INSTALLATION DE LE SECHE-LINGE .......... 35

INSTALLATION DES PIEDS DE NIVELLEMENT ET

DE LA BOÎTE À MONNAIE .......................................................... 36

NIVELLEMENT ................................................................................ 37

EXIGENCES D’INSTALLATION DE LE

SECHE-LINGE ÉLECTRIQUE ...................................................... 38

EXIGENCES D’INSTALLATION DE LE

SECHE-LINGE À GAZ ................................................................... 39

EXIGENCES CONCERNANT L’ÉVACUATION

DE LE SECHE-LINGE .................................................................... 41

RACCORDEMENT A LA CANALISATION DE GAZ ................ 43

CARACTÉRISTIQUES TECHNIQUES —

SECHE-LINGE À GAZ ................................................................... 44

ACHEVER L’INSTALLATION ........................................................ 46

INVERSION DU SENS D’OUVERTURE

DE LA PORTE (FACULTATIF) ...................................................... 47

INSTRUCTIONS DE RÉGLAGE DU

TABLEAU DE COMMANDE ÉLECTRONIQUE

(MODÈLES PD ET PN SEULEMENT) ........................................ 49

MISE AU REBUT DE LE SECHE-LINGE ................................... 54

GARANTIE ...................................................................................... 55

ÍNDICE

SEGURIDAD DE LA SECADORA ................................................56

PARA EL PROPIETARIO

INSTRUCCIONES DE MANTENIMIENTO ................................ 59

SI NECESITA ASISTENCIA ......................................................... 59

PARA EL PERSONAL DE SERVICIO AUTORIZADO

DE WHIRLPOOL

HERRAMIENTAS Y PIEZAS ........................................................ 60

ESPECIFICACIONES .................................................................... 60

DIMENSIONES Y ESPACIOS LIBRES ..................................... 59

REQUISITOS DE INSTALACIÓN DE LA SECADORA ........... 62

INSTALACIÓN DE LAS PATAS NIVELADORAS Y

CAJA DE MONEDAS ..................................................................... 63

NIVELACIÓN ................................................................................... 64

REQUISITOS DE INSTALACIÓN DE LA

SECADORA ELÉCTRICA.............................................................. 65

REQUISITOS DE INSTALACIÓN DE LA

SECADORA A GAS ....................................................................... 66

REQUISITOS DE VENTILACIÓN DE LA SECADORA ........... 68

CONEXIÓN DEL SUMINISTRO DE GAS ................................. 71

ESPECIFICACIONES TÉCNICAS - SECADORA A GAS ...... 72

INSTALACIÓN COMPLETA ......................................................... 74

CÓMO INVERTIR EL SENTIDO DE APERTURA

DE LA PUERTA ............................................................................... 75

INSTRUCCIONES DE PROGRAMACIÓN DEL CONTROL

ELECTRÓNICO (SOLO MODELOS PD Y PN) ......................... 76

ELIMINACIÓN DE LA SECADORA ............................................ 81

GARANTÍA ....................................................................................... 82

SOMMARIO

SICUREZZA DELL'ASCIUGATRICE ............................................ 83

PER IL PROPRIETARIO

ISTRUZIONI PER LA MANUTENZIONE ................................... 86

COME RICHIEDERE ASSISTENZA .......................................... 86

PER IL PERSONALE DI ASSISTENZA

AUTORIZZATO WHIRLPOOL

ATTREZZI E PARTI ........................................................................ 87

SPECIFICHE ................................................................................... 87

DIMENSIONI/SPAZI ................................................................... 88

REQUISITI PER L'INSTALLAZIONE

DELL'ASCIUGATRICE ................................................................... 89

INSTALLAZIONE DEI PIEDINI DI REGOLAZIONE

E GETTONIERA .............................................................................. 90

LIVELLAMENTO ............................................................................. 91

REQUISITI DELL’INSTALLAZIONE

DELL’ASCIUGATRICE ELETTRICO ............................................ 92

REQUISITI DELL’INSTALLAZIONE

DELL’ASCIUGATRICE A GAS .................................................... 93

REQUISITI DI SCARICO DELL'ASCIUGATRICE ..................... 95

COLLEGAMENTO DI ALIMENTAZIONE DEL GAS ................. 97

CARATTERISTICHE TECNICHE - ASCIUGATRICE

A GAS .............................................................................................. 98

COMPLETAMENTO DELL'INSTALLAZIONE ........................... 96

INVERTIRE IL SENSO DI APERTURA DELLO

SPORTELLO (FACOLTATIVO) ................................................... 101

ISTRUZIONI DI CONFIGURAZIONE DEI COMANDI

ELETTRONICI (SOLO MODELLI PD E PN) ........................... 102

ELIMINAZIONE DELL'ASCIUGATRICE ................................... 107

GARANZIA ................................................................................... 108

3

DRYER SAFETY

WARNING – “Risk of Fire”

This is an additional safety alert symbol that alerts you to the risk of fire.

WA RNING

-

“Risk of Fire”

- Clothes dryer installation and service must be performed by a Whirlpool authorized

installer.

- Install the clothes dryer according to the manufacturer’s instructions and local codes.

by the appliance manufacturer as suitable for use with clothes dryers. Flexible venting

materials are known to collapse, be easily crushed, and trap lint. These conditions will

-To reduce the risk of severe injury or death, follow all installation instructions.

- Save these instructions.

4

DRYER SAFETY

WARNING:

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result in serious injury, death or property

damage.

–

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

or any other appliance.

WHAT TO DO IF YOU SMELL GAS:

–

Installation and service must be performed by a qualified installer, service agency, or

the gas supplier.

•

Do not try to light any appliance.

•

Do not touch any electrical switch; do not use any phone in your building.

•

Clear the room, building, or area of all occupants.

•

Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

•

If you cannot reach your gas supplier, call the fire department.

■ It is recommended that the owner post, in a prominent location, instructions for the customer’s use in the event the customer

smells gas. This information should be obtained from your gas supplier.

■ Post the following warning in a prominent location.

FOR YOUR SAFETY

1. DO NOT USE OR STORE GAS OR OTHER FLAMMABLE MATERIALS IN THIS APPLIANCE OR NEAR THIS APPLIANCE.

2. DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION.

3. DO NOT MODIFY THIS APPLIANCE.

5

DRYER SAFETY

■ The appliance is intended, but not limited, to be used in

public areas.

■ Children of less than 3 years should be kept away unless

continuously supervised.

■ The appliance must be disconnected from it's power

source during service and when replacing parts.

■ If drum rotation is blocked due to trapped textiles,

disconnect the dryer from the electrical supply before

gently removing the blockage.

■ If the dryer is not heating, or appears to be defective or

damaged, do not use it. Contact the owner.

■ Do not install or store the dryer where it will be exposed

to the weather.

■ Do not tamper with controls.

■ Clean dryer lint screen before or after each load.

■ Do not use this dryer without the lint screen in place.

■ Do not repair or replace any part of the dryer or attempt

any servicing unless specically recommended in this

Installation Instructions that you understand and have the

skills to carry out.

■ Fabric softeners, or similar products, should be used as

specied by the fabric softener instructions.

■ Items such as foam rubber (latex foam), shower caps,

waterproof textiles, rubber-backed articles and clothes or

pillows tted with foam rubber pads should not be dried

in the tumble dryer.

■ The nal part of a tumble dryer cycle occurs without

heat (cool-down cycle) to ensure that the articles are left

at a temperature that ensures that the items will not be

damaged.

■ WARNING: Never stop a tumble dryer before the end of

the drying cycle unless all items are quickly removed and

spread out so that the heat is dissipated. (Avoids risk of

spontaneous combustion).

■ In case of electrical supply failure, remove the load

quickly and spread it out to avoid risk of spontaneous

combustion.

■ Keep area around the exhaust opening and adjacent

surrounding areas free from the accumulation of lint, dust,

and dirt.

■ The fresh air ventilation openings into the room and into

the dryer must not be blocked or sealed.

■ Emergency stop control: After installation, access to

mains plug (gas dryer) or mains supply (electric dryer)

via a double-pole switch must be maintained at all times

in order to ensure immediate deactivation of the dryer in

case of emergency.

■ The interior of the dryer and dryer exhaust vent should

be cleaned periodically by Whirlpool authorized service

personnel.

■ See “Electrical Requirements” section for earthing

instructions.

■ Adequate ventilation has to be provided to avoid the

back-ow of gases into the room from appliances burning

fuels, including open res.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of re, electric shock, or injury to persons when using the dryer, follow basic precautions,

including the following:

■ Read all instructions before using the dryer.

■ This dryer is intended only for drying clothes and textiles

that have been washed in water. Do not use for any other

purpose.

■ WARNING: If you smell gas, do not use the dryer or any

electrical equipment nearby. Warn other people to clear

the area. Contact the dryer owner immediately.

■ Do not place items exposed to cooking oils in your dryer.

Items contaminated with cooking oils may contribute

to a chemical reaction that could cause a load to catch

re. To reduce the risk of re due to contaminated loads,

the nal part of a tumble dryer cycle occurs without heat

(cool down period). Avoid stopping a tumble dryer before

the end of the drying cycle unless all items are quickly

removed and spread out so that the heat is dissipated.

■ If it is unavoidable that fabrics that contain vegetable or

cooking oil or that have been contaminated by hair care

products be placed in a tumble dryer, they should rst

be washed in hot water with extra detergent – this will

reduce, but not eliminate the hazard.

■ Do not dry articles that have been previously cleaned

in, washed in, soaked in, or spotted with gas,

dry-cleaning solvents, other ammable, or explosive

substances as they give off vapors that could ignite

or explode.

■ Items that have been soiled with substances such as

acetone, alcohol, gas, kerosene, spot removers,

turpentine, waxes, and wax removers should be washed

in hot water with extra detergent before being dried in

the dryer.

■ Do not dry unwashed items in the dryer.

■ Do not use this dryer if industrial chemicals have been

used for cleaning. The possible presence of residual

quantities of aggressive or decomposed chemicals in the

load may produce damage to the dryer and harmful fumes.

■ Do not allow children to play on, in, or with the dryer.

Close supervision of children is necessary when the dryer

is used near children.

■ This dryer is not intended for use by persons (including

children) with reduced physical, sensory, or mental

capabilities, or lack of experience or knowledge,

unless they have been given supervision or instruction

concerning use of the dryer by a person responsible for

their safety.

■ Before the dryer is removed from service or discarded,

remove the door to the dryer compartment.

■ Do not reach into the dryer if the drum is moving.

■ Do not open door while dryer is in operation. It will stop.

■ When loading or re-loading the dryer, avoid touching hot

metal parts of the drum (burn risk).

■ Remove all objects from pockets such as lighters and

matches.

■ Cleaning and user maintenance shall not be made by

children without supervision.

■ WARNING: The appliance must not be supplied through

an external switching device, such as a timer, or connected

to a circuit that is regularly switched on and off by a utility.

■ The dryer must not be installed behind a lockable door, a

sliding door, or a door with a hinge on the opposite side to

that of the dryer in such a way that full opening of the dryer

door is restricted.

SAVE THESE INSTRUCTIONS

6

MAINTENANCE INSTRUCTIONS

If you need help, contact the dealer from whom you purchased the appliance, or a Maytag designated service company. When

calling, please know the purchase date and the complete model and serial number of your appliance. This information will help us to

better respond to your request.

IF YOU NEED ASSISTANCE

■ Clean lint screen before and after each cycle.

■ Removing accumulated lint:

From inside the dryer cabinet:

Lint should be removed every 2 years or more often,

depending on dryer usage. Cleaning should be done by

a Whirlpool authorized person.

From the exhaust vent:

Lint should be removed every 2 years, or more often,

depending on dryer usage.

■ Keep area around dryer clear and free from combustible

materials, gas, and other ammable vapors and liquids.

■ Keep dryer area clear and free from items that would

obstruct the ow of combustion and ventilation air.

If dryer does not operate, check the following:

■ Electrical supply is connected.

■ Circuit breaker is not tripped or house fuse is not blown.

■ Door is closed. Listen closely to hear the door switch

activate.

■ Controls are set in a running or “on” position.

■ For gas dryers, check that gas supply shut-off valves are

set in open position.

WARNING: Improper connection of the equipment-earthing conductor can result in a risk of electric

shock. It is your responsibility to check with a qualied electrician or service representative if you are in doubt

as to whether the dryer is properly earthed and meets all local codes and ordinances. Do not modify the plug

provided with the dryer: If it will not t the outlet, have a proper outlet installed by a qualied electrician.

IF YOU NEED SERVICE:

Contact your authorized Maytag Commercial Laundry distributor. To locate your authorized Maytag Commercial Laundry distributor,

visit www.maytagcommerciallaundry.com.

For written correspondence:

Maytag Commercial Laundry Service Department

2000 N M 63

Benton Harbor, Michigan 49022-2632 USA

7

Tools Needed:

203 mm (8") 203 mm (8") or 254 mm (10") Flat-Blade Screwdriver Phillips Screwdriver

or 254 mm (10") Adjustable Wrench

Pipe Wrench (that opens to 25 mm (1"))

Torx T-20

†

Security 25 mm (1") Hex-Head 8 mm (5⁄16") Socket Wrench Pliers (that open to

Screwdriver or Bit Socket Wrench 39 mm [1

9

/

16

"])

Level Utility Knife 6 mm (1/4") Nut Driver 686 mm (27")

Wood Block

Caulk Gun and Caulk Vent Clamps Pipe-Joint Compound Putty Knife

(for installing new exhaust vent) Suitable for Gas Type

Flashlight (optional) 25 mm (1") Ruler or Measuring Tape

Open-End Wrenches

TOOLS & PARTS

Parts Supplied:

Foot Boots (4) Leveling Legs (4) Security Cone 5/16" Hex Head – 18 x 2

1

⁄2"

Security Bolt

†

TORX and T20 are trademarks of Acument Intellectual Properties, LLC.

These units are sold in multiple regions with different

requirements for measuring capacity. Below are a few of

the valid forms of measure posted on this product:

Dry Linen Capacity: A weight measure that reects a minimum

threshold for dry volume capacity that is needed for import

tariff purposes.

IEC Capacity: The capacity measure that represents the

maximum capacity of dry linens and textiles which the

manufacturer declares can be treated in a specic cycle.

Dry Linen Capacity

10.5 kg (23 lb)

IEC Capacity

9.0 kg (20 lb)

Sound Level

LpA: 58 dB(A) (Kpa+/-10 dB(A))

SPECIFICATIONS

NOTE: The circuit diagram for this dryer is located inside

the lower front panel, within the Tech Sheets.

Technical Specications:

220 – 240 V, 50 Hz. AC

4575W

Total mass: 68 kg max.

8

DIMENSIONS/CLEARANCES

Dimensions

Clearances

Side View Back View

743 mm

(29

1

/4")

889 mm

(35")

210 mm

(8

1

/4")

25 mm

(1")

660 mm

(26")

83 mm

(3

1

/4")

191 mm

(7

1

/2")

38 mm

(1

1

/2")

140 mm

(5

1

/2")

273 mm

(10

3

/

4

")

953 mm

(37

1

/2")

(gas models)

1042 mm

(41")

343 mm

(13

1

/

2

")

Electric

Gas

686 mm

(27")

83 mm

(3

1

/4")

914 mm

(36")

(electric models)

102 mm

(4" dia)

343 mm

(13

1

/2")

0 mm

(0")

0 mm

(0")

381 mm

(15")

356 mm

(14" max)

0 mm

(0")

Front View, Recessed Opening Side View, Recessed In Closet

127 mm

(5")

356 mm

(14" max)

25 mm

(1")

25 mm

(1")

76 mm

(3"/3")

76 mm

(3"/3")

310 cm

2

(48"

2

/48"

2

)

155 cm

2

(24"

2/

24"

2

)

381 mm

(15")

Closet Door to

Front of Dryer

9

Your dryer can be installed in a basement, laundry room, or

recessed area.

This dryer is not intended for installation in a mobile home.

Companion appliance location requirements should also be

considered.

IMPORTANT: Do not install or store the dryer where it

will be exposed to the weather. Proper installation is your

responsibility.

You will need:

■ An grounded electrical outlet located within 1.8 m (6 ft.) of

where the power cord is attached to the back of the dryer.

See “Electrical Requirements.”

■ A level oor with a maximum slope of 25 mm (1") under

entire dryer. Installing the dryer on soft oor surfaces,

such as carpets or surfaces with foam backing, is not

recommended.

Dryer installation clearances

■ The location must be large enough to allow the dryer door

to be fully opened.

■ Additional spacing should be considered for ease of

installation and servicing. The door opens more than 180°.

■ Additional clearances might be required for wall, door, and

oor moldings.

■ Additional spacing of 25 mm (1") on all sides of the dryer

is recommended to reduce noise transfer.

When installing a dryer:

IMPORTANT: Observe all governing codes and ordinances.

■ Check code requirements: Some codes limit or do not

permit installation of clothes dryers in garages, closets,

or sleeping quarters. Contact your local building inspector.

NOTE: For installation in Australia and New Zealand,

install dryer in accordance with AS/NZS 5601.1 and local

governance codes.

■ Gas Dryers only: Make sure that lower edges of the

cabinet, plus the back and bottom sides of the dryer, are

free of obstructions to permit adequate clearance of air

openings for combustion air. See “Recessed Area and

Closet Installation Instructions” below for minimum spacing

requirements.

Location Requirements

DRYER INSTALLATION REQUIREMENTS

(Australia and New Zealand – for full details of installation requirements refer to AS/NZS 5601.1)

Recessed Area and Closet Installation Instructions

This dryer may be installed in a recessed area or closet. For

recessed area and closet installations, minimum clearances

can be found on the warning label on the rear of the dryer

or in “Dimensions/Clearances.”

The installation spacing is in millimeters and is the minimum

allowable. Additional spacing should be considered for ease

of installation, servicing, and compliance with local codes and

ordinances.

If closet door is installed, the minimum unobstructed air

opening in the top and bottom is required. The unobstructed

opening needs to be 1 square inch per 1,000 Btu (252 kcal)

of gas burner output. Output on North American gas dryers

is typically 22,000 Btu; however, Canadian dryers may have

lower output. Louvered doors with equivalent air openings are

acceptable.

The dryer must be exhausted outdoors.

No other fuel-burning appliance may be installed in the same

closet as the dryer.

NOTE: For installation in Australia and New Zealand, refer to

AS/NZS 5601.1 for ventilation requirements.

Closet

Door

Front

View

10

INSTALLING LEVELING LEGS AND COIN BOX

1. Prepare dryer for leveling legs

NOTE: Slide dryer onto cardboard or hardboard before moving

to avoid damaging oor covering.

Using two or more people, move dryer to desired installation

location.

Take tape off front corners of dryer. Open dryer and remove

the literature and parts packages. Wipe drum interior with a

damp cloth to remove any dust.

Take two cardboard corners from the dryer carton and place

them on the oor in back of the dryer. Firmly grasp the body of

the dryer and gently lay it on its back on the cardboard corners.

Disconnect power before making electrical connections.

2. Screw in leveling legs

Examine leveling legs and nd diamond

marking. Screw legs into leg holes by

hand. Use an adjustable wrench or

25 mm (1") hex-head socket wrench

to nish turning legs until diamond

marking is no longer visible. Then t

a covered foot boot over each leg foot.

To protect the oor, use a large piece of cardboard from the

dryer carton. Stand dryer up on the cardboard. Slide the dryer

until it is close to its nal location. Leave enough room for

electrical connection and to connect the exhaust vent.

A longer leveling foot is available if needed on extremely sloped

oors, Part Number 279810.

Foot

Diamond

Marking

(appearance may vary)

The console houses the electronic control board. The board is

factory set for a dry time of 30 minutes. Consult the tech sheet

found inside the dryer toe panel to reset dry time and for other

options.

The card reading mechanism is not included, but is available

from your usual industry sources.

The meter case houses the factory-installed accumulator timer

with actuating arm or service switch.

The service door lock and key and coin box lock and key

may not be included but are available from the usual industry

sources.

1. Install coin box

Remove the service door of the meter case by lifting it up

at the back. Install the money-accepting device. (Refer to

manufacturer’s instructions for proper installation.)

Replace the meter case service door. Put the coin vault with

lock and key in the meter case opening.

Remove cardboard or hardboard from under dryer. Adjust the

legs of the dryer up or down until the dryer is level.

2. Install added security device

Check that power is not supplied to the dryer.

Open and remove the service door.

Insert the narrow part of the security cone into the oblong hole

in the bottom rear of the meter case assembly.

Pass the security bolt through this cone and thread it by hand

into the cage nut below the oblong hole.

Tighten the security bolt by hand a few turns before using a

wrench to tighten until snug.

NOTE: Installing the security bolt provides added security, but

will add to the service time when the top needs to be removed

for servicing the dryer.

security

bolt

security

cone

cage nut

Security

Bolt

Security

Cone

Cage

Nut

11

1. Remove cardboard from beneath dryer. Place a level on top

edges of dryer, checking each side and front. If not level,

tip dryer and adjust legs up or down as shown in Step 3,

repeating as necessary.

LEVELING

Leveling your dryer properly reduces excess noise and vibration.

Not Level LEVEL Not Level

2. Grip dryer from top and rock back and forth, making sure all

four legs are rmly on oor. Repeat, rocking dryer from side

to side. If dryer rocks, go to Step 3 and adjust leveling legs.

3. If dryer is not level, use a 25 mm or 1" open-end or

adjustable wrench to turn the leveling leg counterclockwise

to lower the dryer or clockwise to raise the dryer. Recheck

levelness of dryer and that all four legs are rmly in contact

with the oor. Repeat as needed.

HELPFUL TIP: You may want to prop up front of dryer

about 102 mm (4") with a wood block or similar object that

will support weight of dryer.

12

ELECTRIC DRYER INSTALLATION REQUIREMENTS

Electrical Requirements

.

IMPORTANT: Observe all governing codes and ordinances.

This dryer is supplied without an electric cord and plug. It

must be connected by a Whirlpool authorized service person

to a single-phase electricity supply at the voltage shown

on the dataplate, using a suitable xed wiring installation in

accordance with local and national wiring regulations.

■ A 3-wire circular cord of minimum conductor size 2.5 mm

2

cross-section area should be used.

■ A 25 A (minimum) supply fuse should be used, and a switch

with a clear OFF marking having a contact separation in

both poles that provides full disconnection under over-

voltage category III conditions must be incorporated into the

xed wiring in accordance with local wiring regulations by

a Whirlpool authorized service person. The dryer should be

positioned so that the disconnection switch is clearly visible

and easily accessible to the user. This disconnection switch

also provides the function of an emergency stop control for

the user.

■ A cord clamp bush is provided on the dryer, and should

be tightened on completion of wiring. The electrical mains

terminals are located behind the small rear access panel

(terminal block cover), and connections should be made

in accordance with the terminal markings. Remember to

replace the terminal access panel (terminal block cover).

NOTE: In accordance with the European EMC Directive

(2004/108/EC), the maximum electrical supply system

impedance to which the electric dryer should be connected

is declared to be 0.054 Ohm + j0.034 Ohm.

NOTE: Electrical safety standards: The manufacturer has

chosen compliance with IEC/EN.60335 standards as the

most appropriate for this product.

If codes permit and an additional ground bond wire is used, it

is recommended that a qualied electrician determine that the

ground bond path is adequate.

Recommended Earthing Method

It is your responsibility to contact a qualied electrical installer

to ensure that the electrical installation is adequate and in

conformance with all local codes and ordinances.

13

GAS DRYER INSTALLATION REQUIREMENTS

Electrical Requirements

EARTHING INSTRUCTIONS

SAVE THESE INSTRUCTIONS

IMPORTANT: Observe all governing codes and ordinances.

You will need a grounded electrical outlet located within

610 mm (2 feet) of either side of the dryer.

This dryer is supplied/tted with an electrical supply cord and

plug. It should be connected to electrical supply socket at the

voltage shown on the rating plate. The minimum supply fuse

capacity should be 10 A. The dryer must be positioned so that

the plug is clearly visible and accessible. This plug also provides

the function of an emergency stop control for the user. If the

tted plug is not used, the electrical connection must be carried

out by a competent electrician in accordance with local or

national codes.

If the supply cord is damaged, it must be replaced with a

specially terminated cord by an authorized service agent or

a similarly competent person in order to avoid a hazard.

Do not use an adapter.

Do not use an extension cord.

NOTE: In accordance with the European EMC Directive

(2004/108/EC), the maximum electricity supply system

impedance to which the gas dryer should be connected is

declared to be 0.054 Ohm + j0.034 Ohm.

NOTE: Electrical safety standards: The manufacturer has

chosen compliance with IEC/EN.60335 standards as the

most appropriate for this product.

If codes permit and an additional ground bond wire is used, it

is recommended that a qualied electrician determine that the

ground bond path is adequate.

Using the universal cord included with this dryer:

The gas dryer is equipped with a universal cord with

interchangeable plugs.

1. To use the universal cord, select the plug end that ts

your electrical outlet, and plug it into the adapter on

the supply cord.

2. Secure the plug end in place on the cord by aligning

the 2 cover halves over the cord adapter and clipping

them together.

14

Gas Supply

GAS DRYER INSTALLATION REQUIREMENTS

IMPORTANT: Observe all governing codes and ordinances.

In Australia and New Zealand, refer to AS/NZS 5601.1 – Gas

Installations.

Gas Supply

Before installation, check that the local gas distribution

conditions, nature of gas and pressure, and the adjustment of

the appliance are compatible. Burner information will be found

on the model/serial rating plate in the door recess of the dryer.

If this information does not agree with the type of gas available,

see your dealer.

Natural Gas:

This dryer is factory adjusted for use with NATURAL GAS (G20),

and no further adjustment should be required at installation.

L.P. Gas:

This dryer is also certied for use with L.P. (propane or butane)

gases with appropriate conversion. No attempt shall be made

to convert the appliance from the gas specied on the model/

serial rating plate for use with a different gas without consulting

the serving gas supplier.

Conversion must be done by a Whirlpool authorized service

technician. Gas conversion kit (European Country), part number

W10233219, is available for purchase from your dealer. Gas

conversion kit (Australia), part number W10315369, is available

for purchase from your dealer. Full instructions are supplied

with the kit.

Natural Gas (France/Belgium):

This dryer is also certied for France/Belgium for use with G20/

G25 gases (20 mbar/25 mbar) with appropriate conversion. No

attempt should be made to convert this appliance from the gas

specied on the gas rating label for use with a different gas

without consulting the serving gas supplier. Gas conversion

must be done by a Whirlpool authorized gas service technician.

Conversion kit, part number (W10181947) is available for

purchase from your dealer. Full instructions are supplied with

the kit.

Supply line requirements:

Provide a rigid gas supply line to the dryer location. It should

be minimum 12.5 mm (1/2") ID. When acceptable to the gas

supplier and local codes, 10 mm (3/8") ID rigid supply line may

be used for lengths under 6.1 m (20'). Pipe-joint compounds

resistant to the action of L.P. gas must be used.

NOTE: For installation in Australia and New Zealand, refer to

AS/NZS 5601 for pipe sizing details. All piping is to be in

accordance with AS/NZS 5601.1 – Gas Installations.

Gas connection to the dryer itself should be made by means

of a exible gas hose suitable for the appliance and gas

category in accordance with national installation regulations. If

in doubt, contact the gas supplier. It should be minimum

10 mm (3/8") ID.

A means of restraint should be used between the dryer and the

wall to avoid straining of the rigid gas supply when the dryer

is moved. An appropriate length of chain and a wall hook is

recommended.

The dryer gas inlet connection is a 3/8" NPT thread. An adapter

is supplied for conversion to standard ISO.228-1 thread

(3/8" BSP).

Check for leaks by using an approved noncorrosive leak-

detection solution. Bubbles will show a leak. Correct any leak

found. A pressure measurement tapping is provided on the gas

valve within the dryer, accessible after removal of the lower

front panel.

The dryer must be disconnected from the gas supply piping

system during any pressure testing of that system.

15

DRYER VENTING REQUIREMENTS

WARNING: To reduce the risk of re, this dryer MUST BE

EXHAUSTED OUTDOORS.

IMPORTANT: Observe all governing codes and ordinances.

In Australia and New Zealand, refer to AS/NZS 5601.1 – Gas

Installations.

Dryer exhaust must not be connected into any gas vent,

chimney, wall, ceiling, attic, crawlspace, or a concealed space

of a building. Only rigid or exible metal vent shall be used for

exhausting.

■ Only a 102 mm (4") heavy, metal exhaust vent and clamps

may be used.

■ Do not use plastic or metal foil vent.

Rigid metal vent:

■ Recommended for best drying performance and to avoid

crushing and kinking.

Flexible metal vent: (Acceptable only if accessible to clean)

■ Must be fully extended and supported in nal dryer location.

■ Remove excess to avoid sagging and kinking that may result

in reduced airow and poor performance.

■ Do not install in enclosed walls, ceilings, or oors.

■ The total length should not exceed 2.4 m (7

3

⁄

4

ft.).

NOTE: If using an existing vent system, clean lint from entire

length of the system and make sure exhaust hood is not

plugged with lint. Replace plastic or metal foil vents with rigid

metal or exible metal vents. Review “Vent System Chart” and

if necessary, modify existing vent system to achieve best drying

performance.

102 mm (4") Heavy, Metal Exhaust Vent

Elbows:

■ 45° elbows provide better airow than 90° elbows.

Clamps:

■ Use clamps to seal all joints.

■ Exhaust vent must not be connected or secured with screws

or other fastening devices that extend into interior of duct

and catch lint. Do not use duct tape.

Better

Good

102 mm

(

4"

)

16

DRYER VENTING REQUIREMENTS

102 mm (4") Diameter Exhaust Hoods

Box Hood Louvered Hood Angled Hood

Vent Hoods

Exhaust hood must be at least 305 mm (12") from the ground

or any object that may be in the path of the exhaust (such as

owers, rocks, bushes, or snow).

Maximum Vent Length/Vent Connection

Maximum length of vent system depends upon the type of vent

used, number of elbows, and type of exhaust hood.

Vent System Chart (Rigid Metal Vent)

No. of 90˚ Turns

Box and

Louvered Hood

Angled Hood

0 39.6 m (130 ft.) 39.3 m (129 ft.)

1 38.1 m (125 ft.) 36.3 m (119 ft.)

2 35.1 m (115 ft) 33.2 m (109 ft.)

3 32.3 m (106 ft.) 30.5 m (100 ft.)

4 29.9 m (98 ft.) 28.0 m (92 ft.)

For vent systems not covered by the vent specication chart,

see your parts distributor.

Provision must be made for enough air for combustion and

ventilation. (Check governing codes and ordinances.) See

“Recessed Area and Closet Installation Instructions” in the

“Location Requirements” section.

A 102 mm (4") outlet hood is preferred. However, a 64 mm

(2

1

⁄

2

") outlet exhaust hood may be used. A 64 mm (2

1

⁄

2

") outlet

creates greater back pressure than other hood types. For

permanent installation, a stationary vent system is required.

Connect Vent

1. If connecting to existing vent, make sure the vent is clean.

2. Using a 102 mm (4") clamp, connect vent to exhaust outlet

in dryer.

NOTE: Do not remove vent collar.

Vent System Length

3. Tighten hose clamp with Phillips screwdriver.

4. Make sure the vent is secured to exhaust hood with

a 102 mm (4") clamp.

5. Move dryer into nal position. Do not crush or kink vent.

Make sure dryer is level.

NOTE: Testing for proper ventilation should be done with a

Manometer. Minimum: 0.01" (0.2 mm). Maximum: 0.6" (16 mm).

Vent Collar

12" min.

(305 mm)

305 mm min.

(12")

17

DRYER VENTING REQUIREMENTS

1. Connect gas supply to dryer. If the exible gas hose has

10 mm (3/8") BSP thread, use the supplied conversion

thread adapter. Use pipe-joint compound resistant to the

action of L.P. gas for gas connections.

Make Gas Connection

GAS SUPPLY CONNECTION (on some models)

The outside end of main vent should have a sweep elbow

directed downward.

If main vent travels vertically through the roof, rather than

through wall, install a 180° sweep elbow on end of vent at least

610 mm (2 ft.) above surface of roof.

The opening in wall or roof shall have a diameter 13 mm (1⁄2")

larger than vent diameter. Vent should be centered in opening.

Do not install screening over end of vent for best performance.

A main vent can be used for venting a group of dryers. The

main vent should be sized to remove 5663 l/min. (200 CFM) of

air per dryer. Large-capacity lint screens of proper design may

be used in main vent if checked and cleaned frequently. The

room where the dryers are located should have make-up air

equal to or greater than CFM of all the dryers in the room.

Back-draft dampers are available from your distributor and

should be installed in the vent of each dryer to keep exhausted

air from returning into dryers and to keep exhaust in balance

within main vent. Unobstructed return air openings are required.

Although usually each single-load dryer should have an

unobstructed outdoor air opening of 154 cm

2

(24 in.

2

) (based

on 6.5 cm

2

[1 in.

2

] per 252 kcal [1,000 Btu]), common make-up

air openings are also acceptable. Set up common openings so

the make-up air is distributed equally to all of the dryers. Keep

in mind that the coverage area must be increased by 33% to

account for the use of registers or louvers over the openings.

Also, make-up air openings should not be installed near the

location where exhaust vents exit the building.

Each vent should enter the main vent at an angle pointing in

the direction of the airow. Vents entering from the opposite

side should be staggered to reduce the exhausted air from

interfering with the other vents.

The maximum angle of each vent entering the main vent should

be no more than 30°.

Keep air openings free of dry cleaning uid fumes. Fumes

create acids which, when drawn through the dryer heating

units, can damage dryers and items being dried.

A clean-out cover should be located on the main vent for

periodic cleaning of the vent system.

NOTE: For more dryer venting information, please refer to

Whirlpool document W10100920.

If an Exhaust Hood Cannot be Used Multiple Dryer Venting

* Minimum clearance above

any accumulation of snow,

ice, or debris such as leaves

30˚ max.

Air ow

Air Flow

If necessary for service, open the toe panel. Use a putty

knife to press on the 2 toe panel locks located at the top

of the toe panel. Pull downward on the toe panel to open.

Toe panel is hinged at the bottom.

2. Open the shut-off valve in the gas supply line and make

sure the dryer has its own gas supply opened.

3. Test all connections by brushing on an approved

noncorrosive leak-detection solution. Bubbles will show

a leak. Correct any leaks found.

18

TECHNICAL SPECIFICATIONS – GAS DRYER

220–240 V~50 Hz 1 ph 3 A max. IP24 Clothes capacity: 9.0 kg max. Sound pressure level, Lpa: 58 dBA (uncertainty, Kpa: +/-10

dBA) Total mass: 68 kg max.

Factory set for NATURAL GAS: Injector size: 2.2 mm Heat input gross: 5.9 kW

European Country:

CH, CZ, CY, ES, GB, GR,

IE, IT, LT, PT, SI, SK, TR

BG, CY, CZ, DK, EE, FI, GR,

HR, IT, LT, NO, RO, SE, SI, SK

European Gas Category: II

2H3+

II

2H3B/P

Gas Flow Rate: 0.562703 m

3

/hr 0.562703 m

3

/hr

Supply Pressure (G20): 20 mbar 20 mbar

Factory Adjusted Pressure: 7.4 mbar 7.4 mbar

With L.P. Gas Conversion Kit: Injector size: 1.25 mm Heat input gross: 6.4 kW

European Country:

CH, CZ, CY, ES, GB, GR,

IE, IT, LT, PT, SI, SK, TR

BG, CY, CZ, DK, EE, FI, GR,

HR, IT, LT, NO, RO, SE, SI, SK

European Gas Category:

II

2H3+

II

2H3B/P

Butane Supply Pressure (G30): 28-30 mbar 30 mbar

Adjusted Pressure: N/A N/A

L.P. Supply Pressure (G31): 37 mbar 30 mbar

Adjusted Pressure: N/A N/A

With France/Belgium NATURAL GAS conversion kit: Injector size 1.65 mm Heat input gross: 5.9 kW

European Country: FR, BE

European Gas Category:

I

2E+

Supply Pressure (G20): 20 mbar

Supply Pressure (G25): 25 mbar

Adjusted Pressure: N/A

Factory set for NATURAL GAS: Injector size: 2.2 mm Heat input gross: 5.9 kW

Country:

AT, BG, CH, CZ, DK, EE, ES, FI, GB, GR, HR,

IE, IS, IT, LT, LV, NO, PT, RO, SE, SI, SK, TR

European Gas Category: I

2H

Gas Flow Rate: 0.562703 m

3

/hr

Supply Pressure (G20): 20 mbar

Factory Adjusted Pressure (G20): 7.4 mbar

Factory set for NATURAL GAS: Injector size: 2.2 mm Heat input gross: 5.9 kW

Country: LU, RO

European Gas Category: II

2E3B/P

Gas Flow Rate: 0.562703 m

3

/hr

Supply Pressure (G20): 20 mbar

Factory Adjusted Pressure (G20): 7.4 mbar

With L.P. Gas Conversion Kit: Injector size: 1.25 mm Heat input gross: 6.4 kW

Country: LU, RO

European Gas Category: II

2E3B/P

Butane Supply Pressure (G30): 30 mbar

Adjusted Pressure: N/A

L.P. Supply Pressure (G31): 30 mbar

Adjusted Pressure: N/A

19

TECHNICAL SPECIFICATIONS – GAS DRYER

Factory set for NATURAL GAS: Injector size: 2.2 mm Heat input gross: 5.9 kW

Country: DE, LU, PL, RO

European Gas Category:

I

2E

Gas Flow Rate: 0.562703 m

3

/hr

Supply Pressure (G20): 20 mbar

Factory Adjusted Pressure (G20): 7.4 mbar

Factory set for Australia/New Zealand NATURAL GAS: Injector size: 2.2 mm Heat input gross: 5.9 kW

Country: AU, NZ

Supply Pressure (G20): minimum 1.13 kPa

Adjusted Pressure (Test Point Pressure): 0.74 kPa

Nominal Hourly Gas Consumption: 21.1 MJ/h

With Australia L.P. Gas Conversion Kit: Injector Size: 1.40 mm Heat input gross: 6.54 kW

Country: AU, NZ

L.P. Supply Pressure: 2.75 kPa

Adjusted Pressure: 2.75 kPa

Nominal Hourly Gas Consumption: 23 MJ/h

Factory set for NATURAL GAS: Injector size: 2.2 mm Heat input gross: 5.0 kW

Country: NL

European Gas Category:

I

2L

II

2L3B/P

Gas Flow Rate: 0.562703 m

3

/hr 0.562703 m

3

/hr

Gas Flow Rate: 25 mbar 25 mbar

Factory Adjusted Pressure (G25) : 7.4 mbar 7.4 mbar

With L.P. Gas Conversion Kit: Injector size: 1.25 mm Heal input gross: 6.4 kW

Country: MT, PL NL

European Gas Category

I

3B/P

II

2L3B/P

Butane Supply Pressure (G30) 30 mbar

Adjusted Pressure: N/A

L.P. Supply Pressure: 30 mbar

Adjusted Pressure: N/A

NOTE: Conversion kit: From Natural Gas to L.P. Gas - Europe: Whirlpool Part No. W10233219.

Conversion kit: From Natural Gas to L.P. Gas - Australia: Whirlpool Part No. W10315369.

Conversion kit: From Natural Gas to Natural Gas - France/Belgium: Whirlpool Part No. W10181947.

Manufacturer: Whirlpool Corporation, Benton Harbor, Michigan 49022, U.S.A.

Manufacturing Site: Whirlpool Corporation, 1300 Marion-Agosta Rd., Marion, OH, 43302, U.S.A.

EU Representatives: Whirlpool EMEA S.p.A., Via Carlo Pisacane, 1, 20016 Pero (MI) Italy

20

1. Check the electrical requirements. Be sure that you have

the correct electrical supply and the recommended earthing

method. See “Electrical Requirements.”

2. Check that all parts are now installed. If there is an extra

part, go back through the steps.

3. Check that you have all of your tools.

4. Dispose of/recycle all packaging materials.

5. Plug into an grounded outlet, or connect power.

6. Check dryer operation. Close dryer door. Set the cycle.

Operating time will accumulate per number of coins.

Using a full heat cycle (not the air cycle), let the dryer run

for at least ve minutes. Dryer will stop when time is used

up. Make sure the dryer turns off.

NOTE: Dryer door must be closed for dryer to operate.

When door is open, dryer stops, but timer continues to run.

7. Gas Models only: Open the dryer door. Check that the

inside of the dryer is warm. If the burner does not ignite

and you can feel no heat inside the dryer, shut off dryer for

5 minutes. Check that all supply valve controls are in “ON”

position and that the electrical cord is plugged in. Repeat

ve-minute test.

8. If drying time is too long, make sure that the lint screen is

clean and that there are no obstructions to airow in the

dryer vent system.

9. Restart the dryer and allow it to complete a full heat cycle

(not air cycle) to make sure it is working properly.

COMPLETE INSTALLATION

WARNING

Electric Shock Hazard

This dryer must be earthed.

Securely tighten all electrical connections.

Failure to do so can result in death, fire, or

electric shock.

La page charge ...

Maytag MDG20PNAGW Installation Instructions Manual

Ce manuel convient également à

Maytag MDG20PNAGW Installation Instructions Manual

dans d''autres langues

Documents connexes

Autres documents