EN Installation, Operation and Maintenance Instructions
FR Instructions d’installation, d’utilisation et d’entretien
Built-in Freezers
Congélateurs intégrées
MP24FAS4**
MP24FAP4**
2
Contents:
Safety information .................................................2
Unpacking your appliance .....................................3
Warranty registration .........................................3
Installing your appliance ........................................4
Cabinet clearances ............................................4
Leveling the appliance ........................................4
Electrical connection ..........................................5
Product Dimensions ..............................................6
Starting your appliance .........................................8
Using your Electronic control ................................8
Sleep mode .........................................................8
Turning your appliance "ON" or "OFF" ...............8
Adjusting the temperature ..................................9
Temperature mode .............................................9
Interior lighting ...................................................9
Control lock ........................................................9
Alarms ..............................................................10
Door ajar ......................................................10
Power failure ................................................10
Temperature alarm .......................................10
Temperature sensor error codes .....................11
Vacation mode ...............................................11
Overlay door panel installation ............................12
Shelving congurations .......................................18
Energy saving tips ...............................................18
Care and cleaning ...............................................19
Obtaining service ................................................19
Troubleshooting ...................................................20
Warranty ................................................................22
Important Safety Instructions
Warnings and safety instructions appearing in this
guide are not meant to cover all possible conditions
and situations that may occur. Common sense,
caution, and care must be exercised when install-
ing, maintaining, or operating this appliance.
RECOGNIZE SAFETY SYMBOLS,
WORDS, AND LABELS.
NOTE
!
CAUTION
CAUTION- Hazards or unsafe practices which
could result in personal injury or property / product
damage.
NOTE- Important information to help assure a
problem free installation and operation.
CONTENTS
State of California Proposition 65 Warning:
This product contains one or more chemicals
known to the State of California to cause birth
defects or other reproductive harm.
!
WARNING
State of California Proposition 65 Warning:
This product contains one or more chemicals
known to the State of California to cause
cancer.
!
WARNING
WARNING - You can be killed or seriously
injured if you do not follow these instructions.
!
WARNING
3
UNPACKING YOUR REFRIGERATOR
NOTE
!
CAUTION
Figure 1
Remove Interior Packaging
Your appliance has been packed for shipment with
all parts that could be damaged by movement se-
curely fastened. Remove internal packing materials
and any tape holding internal components in place.
The owners manual is shipped inside the product
in a plastic bag along with the warranty registration
card, and other accessory items.
Important
Keep your carton and packaging until your appli-
ance has been thoroughly inspected and found to
be in good condition. If there is damage, the pack-
aging will be needed as proof of damage in transit.
Afterwards please dispose of all items responsibly.
Note to Customer
This merchandise was carefully packed and
thoroughly inspected before leaving our plant.
Responsibility for its safe delivery was assumed
by the retailer upon acceptance of the shipment.
Claims for loss or damage sustained in transit must
be made to the retailer.
DO NOT RETURN DAMAGED MERCHANDISE TO
THE MANUFACTURER - FILE THE CLAIM WITH
THE RETAILER.
If the appliance was shipped, handled, or stored
in other than an upright position for any period of
time, allow the appliance to sit upright for a period
of at least 24 hours before plugging in. This will
assure oil returns to the compressor. Plugging the
appliance in immediately may cause damage to
internal parts.
Warranty Registration
XXXXXXXXXXXX
XXXXXXXXXXXX
It is important you send in your warranty regis-
tration card immediately after taking delivery of
your appliance or you can register online at www.
marvelrefrigeration.com.
The following
information will
be required when
registering your
appliance.
Service Number
Serial Number
Date of Purchase
Dealer’s name and address
The service number and serial number can be
found on the serial plate which is located inside the
cabinet on the left side near the top. (See gure 1).
Online registra-
tion available at
www.marvelrefriger-
ation.com
WARNING - Help Prevent Tragedies
Child entrapment and suffocation are not
problems of the past. Junked or abandoned
refrigerators are still dangerous - even if they sit
out for "just a few hours".
If you are getting rid of your old refrigerator,
please follow the instructions below to help
prevent accidents.
Before you throw away your old refrigerator or
freezer:
• Take off the doors or remove the drawers.
• Leave the shelves in place so children
may not easily climb inside.
!
WARNING
WARNING - Dispose of the plastic bags which
can be a suffocation hazard.
!
WARNING
EXCESSIVE WEIGHT HAZARD
Use two or more people to move product.
Failure to do so can result in personal injury.
!
WARNING
MARVEL
4
INSTALLING YOUR REFRIGERATOR
Select Location
The proper location will ensure peak performance
of your refrigerator. We recommend a location
where the unit will be out of direct sunlight and
away from heat sources. To ensure your product
performs to specications, the recommended
installation location temperature range is from 55 to
100°F (13 to 38°C) for indoor units and 55 to 115°F
(13 to 46°C) for outdoor units.
Cabinet Clearance
Ventilation is required from the bottom front of the
refrigerator. Keep this area open and clear of any
obstructions. Adjacent cabinets and counter top
can be installed around the refrigerator as long as
the front grille remains unobstructed.
Front Grille
Do not obstruct the front grille. The openings within
the front grille allow air to ow through the con-
denser heat exchanger. Restrictions to this air ow
will result in increased energy usage and loss of
cooling capacity. For this reason it is important this
area not be obstructed and the grille openings kept
clean. Northland does not recommend the use of
a custom made grille as air ow may be restricted.
(See Figure 2).
!
CAUTION
Front Leveling
Legs
Figure 2
Rear
Leveling
Legs
Front Grille, keep
this area open.
Leveling Legs
Adjustable legs at the front and rear corners of
the appliance should be set so the unit is rmly
positioned on the oor and level from side to side
and front to back. The overall height of your Marvel
appliance may be adjusted higher (by turning the
leveling leg out, CCW) and lower (by turning the
leveling leg in, CW) dimensions as shown in Table
"A".
To adjust the leveling legs, place the appliance on a
solid surface and protect the oor beneath the legs
to avoid scratching the oor. With the assistance of
another person, lean the appliance back to access
the front leveling legs. Raise or lower the legs to
the required dimension by turning the legs. Repeat
this process for the rear by tilting the appliance
forward using caution. On a level surface check the
appliance for levelness and adjust accordingly.
The front grille screws may be loosened and the
grille adjusted to the desired height. When adjust-
ment is complete tighten the two front grille screws.
(See Figure 5).
Model Door Style
Minimum
Height
Maximum
Height
MP24* (S)
34"
(86.4 cm)
35"
(88.9 cm)
MP24* (P)
34"
(86.4 cm)
35"
(88.9 cm)
Table A
An optional stacking kit, for 24" wide models,
is required to stack products. Failure to use a
stacking kit could result in personal injury. Con-
tact your dealer or Northland customer service
at 844-875-7064 to order.
!
WARNING
5
INSTALLING YOUR REFRIGERATOR
Figure 3
Figure 4
Do not remove
ground prong
Front grille screw
Front grille
Figure 5
Figure 6
Ground Fault Circuit Interrupters (GFCI) are prone
to nuisance tripping which will cause the appliance
to shut down. GFCI’s are generally not used on
circuits with power equipment that must run unat-
tended for long periods of time, unless required to
meet local building codes and ordinances.
NOTE
Electrical Connection
A grounded 115 volt, 15 amp dedicated circuit is
required.
This product is factory equipped with a power
supply cord that has a three-pronged, grounded
plug. It must be plugged into a mating grounding
type receptacle in accordance with the National
Electrical Code and applicable local codes and or-
dinances (see Figure 6). If the circuit does not have
a grounding type receptacle, it is the responsibility
and obligation of the customer to provide the proper
power supply. The third ground prong should not,
under any circumstances, be cut or removed.
Electrical Shock Hazard
• Do not use an extension cord with this ap-
pliance. They can be hazardous and can
degrade product performance.
• This appliance should not, under any cir-
cumstances, be installed to an un-ground-
ed electrical supply.
• Do not remove the grounding prong from
the power cord. (See Figure 3).
• Do not use an adapter. (See Figure 4).
• Do not splash or spray water from a hose
on the appliance. Doing so may cause
an electrical shock, which may result in
severe injury or death.
!
WARNING
6
PRODUCT DIMENSIONS
MODEL
ROUGH-IN OPENING
DIMENSIONS
"A" "B" "C"
MP24FA(S)
24"
(61 cm)
**34
1
⁄4" to 35
1
⁄4"
(87 to 89.5 cm)
24"
(61 cm)
MP24FA(P)
24"
(61 cm)
**34
1
⁄4" to 35
1
⁄4"
(87 to 89.5 cm)
*24"
(61 cm)
MODEL
CABINET DIMENSIONS
"D" "E" "F" "G" "H" "J"
MP24FA(S)
23
7
⁄8"
(60.7 cm)
34" to 35"
(86.4 to 88.9 cm)
23
23
⁄32"
(60.2 cm)
26
7
⁄32"
(66.6 cm)
46
13
⁄32"
(117.9 cm)
26
7
⁄16"
(67.2 cm)
MP24FA(P)
23
7
⁄8"
(60.7 cm)
34" to 35"
(86.4 to 88.9 cm)
22
7
⁄8"
(58.1 cm)
-
46
1
⁄2"
(118.1 cm)
23
1
⁄8"
(58.7 cm)
DOOR STYLE
(S) Solid Door
(P) Solid Overlay Door (no handle)
Figure 8
If necessary to gain clearance inside the rough-in
opening a hole can be cut through the adjacent cab-
inet and the power cord routed through this hole to a
power outlet. Another way to increase the available
opening depth is to recess the power outlet into the
rear wall to gain the thickness of the power cord
plug. Not all recessed outlet boxes will work for this
application as they are too narrow, but a recessed
outlet box equivalent to Arlington #DVFR1W is rec-
ommended for this application, (see Figure 8).
"A"
"B"
"C"
"D"
"E"
Figure 7
Figure 7a
7
PRODUCT DIMENSIONS
MODEL
PRODUCT DATA
ELECTRICAL
REQUIREMENTS #
PRODUCT
WEIGHT
MP24FA(S) 115V/60Hz/15A
140 lbs
(63.6 kg)
MP24FA(P) 115V/60Hz/15A
140 lbs
(63.6 kg)
* To install (P) models with the door face ush with
adjacent cabinetry doors, custom decorative panel
thickness cannot exceed 3⁄4" (19 mm).
** Minimum rough-in opening required is to be larger
than the adjusted height of the cabinet.
# A grounded 15 amp dedicated circuit is required.
Follow all local building codes when installing electri-
cal and appliance.
"F"
21
1
⁄2"
(54.6 cm)
"D"
"E"
"G"
Figure 9
"J"
"H"
8
Power Failure
Starting your appli-
ance:
Plug the appliance power
cord into a 115 volt wall outlet. Your ap-
pliance is shipped from the factory in the "On" po-
sition and will begin start-up of cooling as soon as
power is supplied. If the appliance does not start,
conrm that the wall outlet has power, and that the
control is in the "On" position, (See "Turning your
appliance On and Off" below).
The control display is covered with a clear plastic
lm. This lm may be removed by carefully lifting
the lm at a corner.
On initial power up, the control display will indicate
a "Power Failure" alarm. This is a normal condition
as the appliance was powered-up at the factory for
quality inspection and then removed from power. A
momentary press of the "On/Off" keypad will reset
this alarm condition. (See Alarms section on page
10).
ALARM RESET
NOTE
Your product has an automatic defrost feature that
utilizes an electric heater element. Periodically
during defrost you may observe the following:
• Water dripping and running sounds as a
result of the frost melt
• Sizzling and popping sounds from water
dripping on the heater element
• A faint reddish glow in the freezer compart-
ment from the electric heater element
These are all “normal” operating characteristics
related to refrigeration product incorporating auto-
matic defrost. They do not represent any product
fault or safety issue.
Temp
Minus
keypad
Temp
Plus
keypad
On/Off
keypad
Light
keypad
Display Area
Lock
keypad
System Status
indicators
Figure 10
Electronic single zone control
Sleep mode:
If no keypads are pressed for 60 seconds, the
display will enter sleep mode to conserve power.
The control panel will go dark with the exception of
the system status "OK" indicator which will remain
enabled. Alarm conditions will wake the display,
(see alarms on page 10).
To make the following changes to the con-
trol settings (turning the appliance ON/OFF,
adjusting the temperature, changing the interior
lights, and activating vacation mode), the con-
trol must be awake.
To wake the display press any keypad. A conrm
tone will sound, and the current storage compart-
ment temperature will be displayed.
Using your electronic control:
The sleep mode can be disabled if you prefer to
have the display on continuously. Press and hold
the "Lock" keypad until the display goes past "Loc"
and reads "nSL". To enable the sleep mode, repeat
the instruction, again going past "Loc" until the
display reads "SLP".
Turning your appliance ON and OFF:
If the appliance is "On", (and out of sleep mode) the
temperature will be shown in the display area of the
control. To turn the appliance "Off", press and hold
the "On/Off" keypad for 4-seconds. "OFF" will now
be displayed on the control.
To turn the appliance "On", press and hold the "On/
Off" keypad for 4-seconds.
STARTING YOUR APPLIANCE
9
USING YOUR ELECTRONIC CONTROL
Adjusting the temperature:
To set or check the set-point temperature (with the
control out of sleep mode), press the "-" or "+" key-
pads. "SET" will be indicated on the user interface
panel and the current set-point temperature will
display and ash. Subsequent presses of the "-" or
"+" keypads will adjust the temperature colder or
warmer respectively. When you have reached your
desired set-point temperature, press the "On/Off"
keypad to accept, or do nothing and the "Set" mode
will time-out in 10-seconds accepting the displayed
temperature as the new set-point.
The available set-point temperature range for your
appliance is -10°F (-23°C) to 10°F (-12°C). If you
attempt to adjust the temperature outside of this
range you will receive an audible notication.
When making temperature set-point changes, it
may take up to 24-hours for the stored contents to
stabilize at your new set-point temperature.
Factors that affect the storage compartment stabi-
lized temperature:
• Changes to temperature setting.
• Room temperature changes.
• Temperature of stored contents.
- Loading warm contents.
- Cold content load will delay the change to a
warmer set-point temperature.
- Warm content load will delay the change to
a colder set-point temperature.
• Usage, (number and duration of the door
openings).
• Installation of the appliance in direct sunlight
or next to a heat source.
NOTE
Loading warm contents may trigger a temperature
alarm, see temperature alarm page 10. Depending
on the quantity and/or weight of warm contents, it
may take 48 hours for the compartment tempera-
ture to stabilize.
Temperature mode:
The temperature mode is preset from the factory in
Fahrenheit (°F) but you have the option to change it
to Centigrade (°C). To change the mode, press and
hold the "-" keypad, while pressing the "+" keypad,
then release the "-" keypad.
The temperature will now be displayed in Centi-
grade (°C). Repeat the procedure to change the
temperature mode back to Fahrenheit (°F).
Interior lighting:
Changing the Tri-Color lighting:
To change the color between white, amber, or
blue, with the control out of sleep mode, momen-
tarily press the "Light" keypad. The keypad will
illuminate. Then press and hold the keypad for
approximately 3 seconds the interior light will start
to cycle through the 3 available colors. On solid
door/drawer product this will need to be done with
the door/drawer open to be able to observe the
colors. Release the keypad when the desired color
is on, and your interior light will be changed to that
color. After selection of color for solid door/drawer
product, the display light feature should be turned-
off, ("Light" keypad not illuminated).
Control lock:
The control panel can be locked to avoid uninten-
tional changes. To lock the control, press and hold
the "Lock" keypad until the display reads "Loc" then
immediately release your nger from the keypad.
The lock icon will ash 3-times and then continu-
ously illuminate. When the control panel is locked,
only the Lock keypad, System Status OK indicator,
and the Alarm indicator are active. To un-lock
the control panel, repeat this instruction until the
display reads "nLc" then immediately release your
nger from the keypad.
NOTE
If the control lock is active (illuminated lock
icon) the control will have to be unlocked
before using the keypad to reset an alarm
condition. See page 9 (Control Lock) for instruc-
tions for unlocking the control.
10
Door Ajar
ALARM RESET
• Door ajar - If the door is open, or not closed
properly, for more than 5-minutes the System
Status OK indicator will turn-off, the "Door
Ajar" indicator will ash, and a tone will sound
every 60 seconds. Additionally, an "ALARM
RESET" indicator will be displayed below the
"On/Off" keypad.
Alarms:
The control will alert you to conditions that could
adversely affect the performance of the appliance.
NOTE
NOTE
NOTE
NOTE
NOTE
The audible alarm can be muted, for each occur-
rence, by pressing the lock keypad.
This alarm condition can be reset by closing the
door or momentarily pressing the "On/Off" keypad,
(i.e.-if you are cleaning the storage compartment,
etc.). The alarm will recur in 5-minutes if the alarm
condition persists.
ALARM RESET
Power Failure
• Power failure - If power to the appliance is
inter-rupted the System Status indicator will
turn-off and the "Power Failure" indicator
will ash. Additionally, an "ALARM RESET"
indicator will be displayed below the "On/
Off" keypad. No audible tone will sound. This
alarm condition can be reset by momentarily
pressing the "On/Off" keypad. If this alarm
occurs, it is recommended that you check
the condition of any perishables, even if the
appliance is operating normally and the tem-
perature has recovered, as prolonged power
outages could result in excessive temperature
excursions which may spoil perishables.
• Temperature alarm - If the storage compart-
ment temperature deviates excessively from
your set-point temperature for an extended
period of time, the "TEMP" indicator will ash,
and an audible tone will sound every 60
seconds. Additionally, an "ALARM RESET"
indicator will be displayed below the "ON/
OFF" keypad.
The audible alarm can be muted, for each occur-
rence, by pressing the lock keypad.
This alarm condition can be reset by momentarily
pressing the "On/Off" keypad. If this alarm occurs
it is recommended that you check the condition of
your stored contents, even though the appliance is
operating normally and the temperature has recov-
ered, as prolonged temperature excursions could
spoil perishables.
ALARM RESET
Temp
After a high temperature alarm condition, check all
perishables to ensure they are safe for consump-
tion.
The temperature alarm may occur as a result of
high usage or introduction of warm contents to the
storage compartment. If the temperature alarm
continues to occur, your unit may require service.
Door Ajar
Temp
Multiple alarms are possible, i.e.- "Door Ajar" for
a prolonged period may trigger a "Temp" alarm, in
which case both "Door Ajar" and "Temp" indicators
will activate.
USING YOUR ELECTRONIC CONTROL
11
USING YOUR ELECTRONIC CONTROL
Temperature Sensor Error Codes
Sensor
Displayed
Code
Error
Description Action to Take
Single Zone
Temperature
Sensor
Failed temperature sensor in the
single zone compartment. Can lead
to unwanted storage temperatures
and/or spoiled perishable goods.
Call service to have the
temperature sensor replaced
and remove all perishable goods
from compartment to prevent
spoilage.
Defrost
Sensor
Failed defrost temperature sensor.
Causes unit to not defrost properly
and can create large frost build-up.
Can lead to water damage to the
unit and surrounding oor.
Unplug the power cord
immediately and call service
to have the defrost sensor
replaced.
The temperature sensors are monitored continu-
ously. Any OPEN or SHORTED circuit condition will
initiate an ERROR CODE as listed below:
Temperature Sensor Error Codes
Vacation mode:
This operating mode can be used to save energy
during high cost energy periods, or when you won't
be using your appliance for an extended period
of time by disabling the lights, alarm tones, and
keypad entry tones. Vacation mode also serves
as a Sabbath mode, disabling functions and its
controls in accordance with the weekly Sabbath
and religious holidays observed within the Orthodox
Jewish community. When used as Sabbath mode,
you may open or close the door at any time to ac-
cess contents without concern of directly turning on
or off any lights, digital readouts, solenoids, fans,
valves, compressor, icons, tones, or alarms.
When activated, the display, alarm indicators and
tones, keypad touch tones, interior lights, and
all options are disabled. All keypad functions are
disabled, with the exception of the "On/Off" keypad
which is required to exit Vacation mode. Storage
compartment temperatures are monitored and
controlled at the settings prior to entering Vacation
mode.
To enter Vacation Mode (with the control out of
sleep mode), press and hold the "On/Off" keypad
until the display goes past "OFF" and reads "VAC".
The display will ash "VAC" 3-times to acknowledge
your request, then will display "VAC" continuously
until Vacation mode is exited. A power outage will
not exit Vacation mode, exiting can only be accom-
plished manually. To exit Vacation mode and return
to normal operation, press and hold the "On/Off"
keypad until the control displays the temperature.
12
OVERLAY DOOR PANEL INSTALLATION
If you purchased an overlay panel model, your
unit is equipped with articulated hinges to allow
fully integrated built-in installations. Custom panel
thicknesses of
5
⁄8" (15 mm) and
3
⁄4" (18 mm) are
accommodated.
!
CAUTION
It is important to use the factory provided grille that
came with the product to assure proper air ow is
maintained through the condenser. The use of a
custom grille is not recommended and will void the
warranty.
Figure 11
Figure 11b
Bottom of door
Figure 11a
Loosen (do not
remove) these
2 phillips head
screws on the
top and bottom
hinges
"P" clamp
and screw
Wire connector
see Figure 12
Cabinet
"Z" Bracket
Step 1: Removing the Door
With a phillips screwdriver remove the screw and
"P" clamp from the bottom of the door near the
hinge. See Figure 11b.
Disconnect the door wire harness by pressing and
holding down the locking tab on the wire connector
and pulling the connector apart. See Figure 12.
Open the door and loosen the screws holding the
hinges to the cabinet (2 at the top and 2 at the bot-
tom hinge). Do not remove the screws but loosen
them enough so the hinges can be slipped off of the
screws when sliding the door to the side.
With a helper, and being careful not to scratch the
cabinet or the door, slide the door to the side about
1
⁄2 inch and remove the hinges and door from the
unit.
The articulated hinges have many pinch points.
Carefully close / collapse the hinges as soon as
the door is removed from the cabinet.
!
WARNING
Overlay panel models are designed for use with
built-in installations only. Use in freestanding
installations could result in personal injury.
!
WARNING
Use extreme caution with the articulated hinges.
The hinge is self closing and many pinch points
exist prior to built-in installation. Do not remove
the cabinet "Z" bracket from the top of the
cabinet.
!
WARNING
13
OVERLAY DOOR PANEL INSTALLATION
Step 2: Remove the door gasket
With the door laying on a at surface and starting
at a corner of the door remove the magnetic door
gasket from the interior side of the door, see
Figure 13. Set the gasket aside on a at surface.
There are 10 holes in the gasket retainer extru-
sions, (3 on each side and 2 at the top and bottom
which are used to fasten the panel to the front of
the door. The screws are provided in the literature
pack.
Figure 12
Press and hold down this
tab on the wire connector
and pull the connector apart.
Figure 13
Figure 13a
Overlay panel ush
with top of door.
Holes in
gasket
retainer.
Magnetic
Gasket remove
starting at a
corner, grasp
and pull away
from the door.
Overlay
panel to be
centered on
width of door.
14
OVERLAY DOOR PANEL INSTALLATION
Figure 15
Left Hand Hinged Door
24" (61 cm) wide appliance
23
3
⁄4"
(60.3 cm)
1" (2.5 cm) diameter
x
1
⁄4" (6 mm) deep
4 places
4
7
⁄8"
(12.4 cm)
1
3
⁄16"
(3 cm)
14"
(35.6 cm)
1
⁄4" (6 mm)
radius is
permissible
3
1
⁄8"
(7.9 cm)
1
3
⁄4"
(4.4 cm)
2"
(5.1 cm)
3
11
⁄16"
(9.4 cm)
1
1
⁄2"
(3.8 cm)
typical
1
⁄4"
(6 mm)
Deep
1
11
⁄16"
(4.3 cm)
Hinge side of door
Top of door
Clearance for hinge
at top and bottom
Clearance for
screw head, 4
places
Figure 14
Left Hand
Hinged Door
24" (61 cm) wide
appliance
This side
facing interior
1
5
⁄32"
(2.9 cm)
Step 3: Cut and drill the overlay panel
Depending on your model cut the overlay door panel
to the dimensions shown in Figures 14 to 17. If your
appliance has a lock also drill the lock hole in the
panel, see Figure 18.
30
11
⁄32"
(77.1 cm)
15
OVERLAY DOOR PANEL INSTALLATION
Clearance for hinge
at top and bottom
Hinge side of door
Top of door
Clearance for
screw head, 4
places
Figure 16
Right Hand
Hinged Door
24" (61 cm)
wide appliance
Figure 17
Right Hand Hinged Door
24" (61 cm) wide appliance
23
3
⁄4"
(60.3 cm)
1" (2.5 cm) diameter
x
1
⁄4" (6 mm) deep
4 places
4
7
⁄8"
(12.4 cm)
1
3
⁄16"
(3 cm)
14"
(35.6 cm)
1
⁄4" (6 mm)
radius is
permissible
3
1
⁄8"
(7.9 cm)
1
3
⁄4"
(4.4 cm)
2"
(5.1 cm)
3
11
⁄16"
(9.4 cm)
1
1
⁄2"
(3.8 cm)
typical
1
⁄4"
(6 mm)
Deep
1
11
⁄16"
(4.3 cm)
This side
facing interior
1
5
⁄32"
(2.9 cm)
!
CAUTION
Weight of overlay door panel must not exceed 15
pounds (6.8 kg) for a solid door model.
30
11
⁄32"
(77.1 cm)
16
OVERLAY DOOR PANEL INSTALLATION
Table B
Material
Type #10 Wood Screw
Hardwood
1
⁄8" (3.2 mm) Diameter. Pilot Hole
Softwood
7
⁄64 (2.8 mm) Diameter. Pilot Hole
Step 4: Assemble the panel to the
door
The preferred method of attaching the panel to the
door is to clamp the panel to the door so it cannot
move while drilling the screw pilot holes. Use bar
clamps or "C" clamps with pads on the clamping
surfaces that will not mar the panel or the door.
The custom overlay panel should be ush with the
top of the door and centered along the width of the
door. See Figure 13a. Drill holes through the gasket
extrusion using the 10 holes as pilot holes. Use the
drill size from the chart in Table "B", being careful
not to drill through the front surface of the panel. If
the overlay panel is thinner than
5
⁄8" (16 mm) thick
shorter screws will have to be obtained. Fasten
the panel to the door with the 10 screws provided
in the literature pack. (See Figure 18a). Remove
the clamps and replace the gasket in the gasket
extrusion channels of the door. Some force may be
required to seat the gasket into the channels. Be
sure the gasket corners are seated properly.
Figure 18
3
1
⁄2"
(89 mm)
Counter bore lock
hole on back side.
Figure 18a
#10 x
1
⁄2"
screw
1
⁄2" (13 mm) diameter drill
through door panel, from
other side (see detail above)
13
⁄16" (20.5 mm) counter bore,
7
⁄16" (11 mm) deep.
17
⁄32"
(13.7 mm)
Hinge side of door
Step 5: Assemble lock parts
Two (2) lock extensions are provided with the lock.
Use the longer extension for
3
⁄4" thick overlay pan-
els and the shorter one for
5
⁄8" thick overlay panels.
Assemble the lock extension, cam stop washer,
spring washer, and set screw to the lock as shown
in Figure 19 and 20.
Install this lock assembly into the lock hole in the
overlay panel and secure with the retaining nut on
the back side with a 15 mm socket and ratchet.
Make sure the key slot in the front of the lock is
vertical.
17
OVERLAY DOOR PANEL INSTALLATION
SECTION A-A
SCALE 1 : 1
LOCK
NUT
BRASS EXTENSION
CAM
PHILLIPS SCREW
13/16 COUNTER
BORE 7/16 DEEP
1/2 HOLE
3/4 INCH
WOOD PANEL
SPRING WASHER
INNER
DOOR
Figure 20
Step 6: Install lock cam
Attach the lock cam to the back of the lock assem-
bly with the phillips head screw provided. Orient the
lock cam vertically when installing on the lock.
Figure 19
Cam stop
washer
Spring
washer
Cam
Set screw
Lock
Key
Retainer
nut
Screw
Brass extension
(2 lengths provided
Step 8: Secure the cabinet
Use the #8 x
3
⁄4" black screws from the literature
pack to secure the counter top to the cabinet top
through the holes in the cabinet "Z" bracket.
Step 7: Install the door
Carefully open the top and bottom hinges on the
door being careful as there are many pinch points.
Place the hinges over the 4 screws in the cabinet,
2 at the top and 2 at the bottom and slide the door
into position. Tighten the 4 hinge screws with a
phillips screwdriver. (See Figures 11 and 11a).
Place wire harness from the grille and mount to the
bottom of the door with the screw and "P" clamp
removed in step 1. (See Figure 11b). Reconnect the
wire harness, (See Figure 12).
Cabinet
"Z" bracket
#8 x 3⁄4" black
screws
(3 places)
Figure 21
18
Figure 22
Freezer:
Loading Tips and Suggestions
Your appliance is equipped with a basket system
which provides maximum adjustability and custom-
izing of the storage arrangements listed below.
24" (61 cm) Wide Models:
Shown with a solid door. Figure 22.
(3) pull-out metal baskets
The following suggestions will minimize the cost of
operating your refrigeration appliance.
1. Do not install your appliance next to a hot
appliance (cooker, dishwasher, etc.), heating
air duct, or other heat sources.
2. Install product out of direct sunlight.
3. Ensure the front grille vents at front of
appliance beneath door are not obstructed
and kept clean to allow ventilation for the
refrigeration system to expel heat.
4. Plug your appliance into a dedicated power
circuit. (Not shared with other appliances).
5. When initially loading your new product, or
whenever large quantities of warm contents
are placed within refrigerated storage com-
partment, minimize door openings for the next
12 hours to allow contents to pull down to
compartment set temperature.
6. Maintaining a relatively full storage compart-
ment will require less appliance run time than
an empty compartment.
7. Ensure door closing is not obstructed by
contents stored in your appliance.
8. Allow hot items to reach room temperature
before placing in product.
9. Minimize door openings and duration of door
openings.
10. Use the warmest temperature control set
temperature that meets your personal prefer-
ence and provides the proper storage for your
stored contents.
11. When on vacation or away from home for
extended periods, set the appliance to warm-
est acceptable temperature for the stored
contents.
12. Set the control to the “off” position if cleaning
the appliance requires the door to be open for
an extended period of time.
SHELVING CONFIGURATIONS AND ENERGY SAVING TIPS
To remove the basket:
Press this tab on each side of the
basket slide and pull the basket
out of the slides.
To install the basket:
Insert the basket slides into the ends of the cabinet
slides and push the basket completely closed. The
slide members will automatically lock together.
Figure 23
Figure 23a
19
Front Grille
Be sure that nothing obstructs the required air ow
openings in front of the cabinet. At least once or
twice a year, brush or vacuum lint and dirt from the
front grille area (see page 4).
SHOCK HAZARD: Disconnect
electrical power from the appliance
before cleaning with soap and
water.
Cabinet
The painted cabinet can be washed with either
a mild soap and water and thoroughly rinsed
with clear water. NEVER use abrasive scouring
cleaners.
Interior
Wash interior compartment with mild soap and
water. Do NOT use an abrasive cleaner, solvent,
polish cleaner or undiluted detergent.
Care of Appliance
1. Avoid leaning on the door, you may bend the
door hinges or tip the appliance.
2. Exercise caution when sweeping, vacuuming
or mopping near the front of the appliance.
Damage to the grille can occur.
3. Periodically clean the interior of the appliance
as needed.
!
CAUTION
CARE AND CLEANING AND OBTAINING SERVICE
If Service is Required:
• If the product is within the rst year warranty
period please contact your dealer or call
Marvel Customer Service at 800.223.3900 for
directions on how to obtain warranty cover-
age in your area.
• If the product is outside the rst year warranty
period, Marvel Customer Service can provide
recommendations of service centers in your
area. A listing of authorized service centers is
also available at www.marvelrefrigeration.com
under the service and support section.
• In all correspondence regarding service, be
sure to give the service number, serial num-
ber, and proof of purchase.
• Try to have information or description of
nature of the problem, how long the appliance
has been running, the room temperature, and
any additional information that may be helpful
in quickly solving the problem.
• Table "C" is provided for recording pertinent
information regarding your product for future
reference.
For Your Records
Date of Purchase
Dealer’s name
Dealer’s Address
Dealer’s City
Dealer’s State
Dealer’s Zip Code
Appliance Serial Number
Appliance Service Number
Date Warranty Card Sent (Must be
within 10 days of purchase).
Table C
4. Periodically check and/or clean the front grille
as needed.
In the Event of a Power Failure
If a power failure occurs, try to correct it as soon
as possible. Minimize the number of door openings
while the power is off so as not to adversely affect
the appliance's temperature.
Light assembly replacement
All models use LED lamps to illuminate the interior
of the appliance. This component is very reliable,
but should one fail, contact a qualied service
technician for replacement of the LED.
20
Before You Call for Service
If the appliance appears to be malfunctioning, read
through this manual rst. If the problem persists,
check the troubleshooting guide below. Locate the
problem in the guide and refer to the cause and
its remedy before calling for service. The problem
may be something very simple that can be solved
without a service call. However, it may be required
to contact your dealer or a qualied service tech-
nician.
NOTE
NOTE
Your freezer has been designed to be very energy
efcient. Because of this the storage compart-
ment has an almost air tight seal. Therefore when
accessing contents and closing the door, the warm
air intrusion will collapse due to the cold compart-
ment temperature creating a slight vacuum inside
the unit. This may make the door harder to open
for about 10 seconds until the internal pressure
equalizes with the exterior.
!
CAUTION
In the unlikely event you lose cooling in your unit,
do not unplug the product from the electric supply,
but do call a qualied service technician immediate-
ly. It is possible that the loss of cooling capacity is a
result of excessive frost build-up on the evaporator
cooling coil. In this case, removing power to the unit
will result in the melting of this excessive quantity of
ice, which could generate melt water that exceeds
the capacity of the defrost drain system and could
result in water damage to your home. The end-user
will be ultimately responsible for any water damage
caused by prematurely turning the unit off without
appropriately managing the excess water run-off.
Your product has an automatic defrost feature that
utilizes an electric heater element. Periodically
during defrost you may observe the following:
• Water dripping and running sounds as a
result of the frost melt
• Sizzling and popping sounds from water
dripping on the heater element
• A faint reddish glow in the freezer compart-
ment from the electric heater element
These are all “normal” operating characteristics
related to refrigeration product incorporating auto-
matic defrost. They do not represent any product
fault or safety issue.
TROUBLESHOOTING
• Never attempt to repair or perform mainte-
nance on the appliance until the main electrical
power has been disconnected. Turning the
appliance control "OFF" does not remove
electrical power from the unit's wiring.
• Replace all parts and panels before operating.
Electrocution Hazard
!
WARNING
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
dans d''autres langues
- English: Marvel undefined User guide
Documents connexes
-
Marvel MA15CRS1LS Mode d'emploi
-
Marvel ML24BCF2RP Manuel utilisateur
-
Marvel ML15BCG2LS2 Mode d'emploi
-
Marvel ML15CPS1RB Mode d'emploi
-
Marvel 60RDE-BB-O Mode d'emploi
-
Marvel 3BARM-BS-G-L Mode d'emploi
-
-
-
-
Marvel MLBV215IS01A Le manuel du propriétaire