Electrolux EFDE317TIW Manuel utilisateur

EN FRONT LOAD DRYER

FR SÉCHEUSE Á CHARGEMENT FRONTAL

ES SECADORA DE CARGA FRONTAL

INSTALLATION INSTRUCTIONS

INSTRUCTIONS D’INSTALLATION

INSTRUCCIONES DE INSTALACIÓN

A11199801 January 2018

2

Important Safety Instructions

WARNING

For your safety, the information in this manual must be followed to minimize the risk of

ﬁre or explosion or to prevent property damage, personal injury or loss of life. DO NOT

store or use gasoline or other ﬂammable vapors and liquids in the vicinity of this or any

other appliance.

Safety Precautions

DO NOT attempt to install or operate

your unit until you have read the safety

precautions in this manual. Safety items

throughout this manual are labeled with a

Danger, Warning, or Caution based on the

risk type.

Deﬁnitions

This is the safety alert symbol. It is

used to alert you to potential personal injury

hazards. Obey all safety messages that

follow this symbol to avoid possible injury

or death.

IMPORTANT

Indicates installation, operation, or main-

tenance information which is important

but not hazard-related.

CAUTION

CAUTION indicates a potentially hazard-

ous situation which, if not avoided, may

result in minor or moderate injury.

WARNING

WARNING indicates a potentially hazard-

ous situation which, if not avoided, could

result in death or serious injury.

DANGER

DANGER indicates an imminently haz-

ardous situation which, if not avoided,

will result in death or serious injury.

Table of Contents

Important Safety Instructions ................2

Installation Requirements ...................... 4

Installation Instructions .......................12

Reversing Door ...................................19

Options ..............................................21

3

Important Safety Instructions

WARNING

RISK OF FIRE

Read all the following instructions before installing and using this appliance.

• Destroy the carton and plastic bags after the laundry center is unpacked. Children

might use them to play. Cartons covered with rugs, bedspreads, or plastic sheets

can become airtight chambers causing suffocation. Place all materials in a garbage

container or make materials inaccessible to children.

• Clothes dryer installation and service must be performed by a qualiﬁed installer,

service agency or the gas supplier.

• Install the clothes dryer according to the manufacturer’s instructions and local codes.

• The electrical service to the dryer must conform with local codes and ordinances

and the latest edition of the National Electrical Code, ANSI/NFPA 70, or in Canada,

the Canadian Electrical Code CSA C22.1 part 1.

• The gas service to the dryer must conform with local codes and ordinances and the

latest edition of the National Fuel Gas Code ANSI Z223.1/NFPA 54, or in Canada,

the Natural Gas and Propane Installation Code, CSA B149.1. An individual manual

shutoff valve must be installed within 6 ft (1.83 m) of the dryer in accordance with the

National Fuel Gas Code, ANSI Z223.1/NFPA 54.

• The dryer is designed under ANSI Z21.5.1/CSA 7.1 or UL 2158 - CAN/CSA C22.2

No. 112 (latest editions) for HOME USE only. This dryer is not recommended for

commercial applications such as restaurants, beauty salons, etc.

• DO NOT install a clothes dryer with ﬂexible plastic or ﬂexible foil venting

material. Flexible venting materials are known to collapse, be easily crushed

and trap lint. These conditions will obstruct clothes dryer airﬂow and in-

crease the risk of ﬁre.

• DO NOT stack a dryer on top of washer already installed on pedestal. DO NOT stack

washer on top of dryer. DO NOT stack washer on top of another washer.

• The instructions in this manual and all other literature included with this dryer are not

meant to cover every possible condition and situation that may occur. Good safe

practice and caution MUST be applied when installing, operating and maintaining

any appliance.

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

4

Installation Requirements

Tools and materials needed for installation:

Please read and save

this guide

Thank you for choosing Electrolux, the

premium brand in home appliances. These

Installation Instructions are part of our

commitment to customer satisfaction and

product quality throughout the life of your

new appliance.

Questions?

Toll-free telephone and online support:

U.S.

1-877-4ELECTROLUX (1-877-435-3287)

www.electroluxappliances.com

Canada

1-800-265-8352

www.electroluxappliances.ca

Exhaust Venting

 Free-ﬂowing, clear of lint buildup

 4 inch (102 mm) rigid or semi-rigid

ducting of minimal length and turns

 NO foil or plastic venting material

 Approved vent hood exhausted to

outdoors

Leveling

 Dryer is level, side-to-side and front-

to-back

 Cabinet is sitting solid on all corners

Gas Supply (Gas Dryer)

 Manual shutoff valve present in

supply

 All connections sealed with approved

sealer and wrench tight

 Conversion kit for LP GAS system

 Gas supply turned on

 No leaks present at all connections

- check with soapy water, NEVER

check with ﬂame

240v Electric Supply (Electric

Dryer)

 Approved NEMA 10-30 or 14-30

service cord with all screws tight on

terminal block

 Approved strain relief installed

 Terminal access cover installed

before initial operation

Door Reversal

 Follow detailed instructions in this

guide

 Test hinge and latch for function

Electrical Power

 House power turned on

 Dryer plugged in

Final Checks

 Installation Instructions and Use and

Care Guide read thoroughly

 Door latches and drum tumbles

when cycle starts

 Registration card sent in

Installation Checklist

5

Electrical system

requirements

Electrical Requirements For

Electric Dryer:

CIRCUIT - Individual 30 amp. branch circuit

fused with 30 amp. time delay fuses or

circuit breakers. Use separately fused

circuits for washer and dryer. DO NOT

operate washer and dryer on same circuit.

POWER SUPPLY - 3-wire or 4-wire,

120/240 volt, single phase, 60 Hz, Alter-

nating Current.

NOTE

Because of potentially inconsistent voltage

capabilities, the use of this dryer with power

created by gas powered generators, solar

powered generators, wind powered gener-

ators or any other generator other than the

local utility company is not recommended.

NOTE

A 120/208 volt, single phase, 60 Hz,

Alternating Current supply may be used on

dryers marked for use on rating plate.

IMPORTANT

Dryer is internally grounded to neutral

unless it was manufactured for sale in

Canada.

Only a 4-conductor cord shall be used

when the appliance is installed in a loca-

tion where grounding through the neu-

tral conductor is prohibited. Grounding

through the neutral link is prohibited for: (1)

new branch circuit installations, (2) mobile

homes, (3) recreational vehicles, and (4)

areas where local codes DO NOT permit

grounding through the neutral.

WARNING

FIRE HAZARD

• Failure to follow safety warnings

exactly could result in serious injury,

death, or property damage.

• DO NOT install a booster fan in dryer

exhaust duct.

• Install all clothes dryers in accor-

dance with the installation instruc-

tions in this manual.

Adjustable

pliers

4 inch, rigid metal or

semi-rigid metal exhaust duct work

Adjustable

wrench

Metal foil

tape (not

duct tape)

External

vent hood

or

Carpenter’s

level

Optional

universal

accessory

wrench

Pipe wrench

for gas

supply

gas line

shutoff valve

(gas dryer)

or

LP-resistant

thread tape

(for natural

gas or

LP supply)

½” NPT

union flare

adapters (x2)

and flexible

gas supply line

(gas dryer)

3-wire or 4-wire

240 volt cord kit

(electric dryer)

Phillips,

straight, &

square bit

screwdrivers

4 in.

(10.2 cm)

clamp

Installation Requirements

Tools and materials needed for

installation:

6

1. Installation MUST conform with local

codes, or in the absence of local

codes, with the National Fuel Gas

Code, ANSI Z223.1 (latest edition).

Installation Requirements

3-WIRE POWER SUPPLY CORD

(not supplied)

OUTLET RECEPTACLE - NEMA 14-30R

receptacle to be located so the power

supply cord is accessible when the dryer

is in the installed position.

GROUNDING CONNECTION - See

“Grounding requirements” in Electrical

Installation section.

The dryer MUST employ a 3-conductor

power supply cord NEMA 10-30 type

SRDT rated at 240 volt AC minimum, 30

amp, with 3 open end spade lug con-

nectors with upturned ends or closed

loop connectors and marked for use with

clothes dryers. For 3-wire cord connection

instructions see ELECTRICAL CONNEC-

TIONS FOR A 3-WIRE SYSTEM.

OUTLET RECEPTACLE - NEMA 10-30R

receptacle to be located so the power

supply cord is accessible when the dryer

is in the installed position.

4-WIRE POWER SUPPLY CORD

(not supplied)

The dryer MUST employ a 4-conductor

power supply cord NEMA 14-30 type

SRDT or DRT (as required) rated at 240

volt AC minimum, 30 amp, with 4 open

end spade lug connectors with upturned

ends or closed loop connectors and

marked for use with clothes dryers. For

4-wire cord connection instructions see

ELECTRICAL CONNECTIONS FOR A

4-WIRE SYSTEM.

Electrical Requirements For Gas

Dryer:

CIRCUIT - Individual, properly polarized and

grounded 15 amp. branch circuit fused

with 15 amp. time delay fuse or circuit

breaker.

POWER SUPPLY - 2-wire, with ground,

120 volt, single phase, 60 Hz, Alternating

Current.

POWER SUPPLY CORD - Dryer is equipped

with a 120 volt 3-wire power cord.

GROUNDING CONNECTION - See

“Grounding requirements” in Electrical

Installation section.

Grounding type wall receptacle

Power cord with

3-prong grounded plug

Do not, under

any circumstances,

cut, remove,

or bypass the

grounding prong.

3-wire receptacle

(NEMA type 10-30R)

4-wire receptacle

(NEMA type 14-30R)

GROUNDING CONNECTION - See

“Grounding requirements” in Electrical

Installation section.

NOTE

Dryers manufactured for sale in Canada

have factory-installed, 4-wire power

supply cord (NEMA 14-30).

Gas supply requirements

WARNING

EXPLOSION HAZARD

Uncoated copper tubing will corrode when

subjected to natural gas, causing gas leaks.

Use ONLY black iron, stainless steel, or

plastic-coated brass piping for gas supply.

WARNING

Improper grounding of the dryer may

cause serious injury or death. Check with

a licensed electrician if you are in doubt

as to whether the appliance is properly

grounded.

7

Installation Requirements

Exhaust system

requirements

If your present system is made up of

plastic duct or metal foil duct, replace

it with a rigid or semi-rigid metal duct.

Ensure the present duct is free of any

lint prior to installing dryer duct.

Use only 4 inch (102 mm) diameter

(minimum) rigid or ﬂexible metal duct and

approved vent hood which has a swing-

out damper(s) that open when the dryer

is in operation. When the dryer stops, the

dampers automatically close to prevent

drafts and the entrance of insects and

rodents. To avoid restricting the outlet,

maintain a minimum of 12 inches (30.5

cm) clearance between the vent hood and

the ground or any other obstruction.

Correct Incorrect

The following are speciﬁc require-

ments for proper and safe operation of

your dryer.

WARNING

FIRE HAZARD

Failure to follow these instructions can cre-

ate excessive drying times and ﬁre hazards.

WARNING

FIRE HAZARD

DO NOT install a clothes dryer with ﬂex-

ible plastic or metal foil venting materials.

Flexible venting materials are known to

collapse, be easily crushed and trap lint.

These conditions will obstruct clothes

dryer airﬂow and increase the risk of ﬁre.

WARNING

FIRE HAZARD

• Failure to follow safety warnings ex-

actly could result in serious injury,

death, or property damage.

• DO NOT install a booster fan in dryer

exhaust duct.

• Install all clothes dryers in accor-

dance with the installation instruc-

tions in this manual.

Gas supply requirements, con-

tinued

2. The gas supply line should be 1/2 inch

(1.27 cm) pipe.

3. If codes allow, ﬂexible metal tubing

may be used to connect your dryer to

the gas supply line. The tubing MUST

be constructed of stainless steel or

plastic-coated brass.

4. The gas supply line MUST have an

individual shutoff valve installed in ac-

cordance with the B149.1, Natural Gas

and Propane Installation Code.

5. A 1/8 inch (0.32 cm) N.P.T. plugged

tapping, accessible for test gauge con-

nection, MUST be installed immediately

upstream of the gas supply connection

to the dryer.

6. The dryer MUST be disconnected from

the gas supply piping system during

any pressure testing of the gas supply

piping system at test pressures in

excess of 1/2 psig (3.45 kPa).

7. The dryer MUST be isolated from the

gas supply piping system during any

pressure testing of the gas supply pip-

ing system at test pressures equal to or

less than 1/2 psig (3.45 kPa).

8. Connections for the gas supply must

comply with the Standard for Connec-

tors for Gas Appliances, ANSI Z21.24/

CSA 6.10.

8

Installation Requirements

The dryer must be connected to an

exhaust outdoors. Regularly inspect the

outdoor exhaust opening and remove any

accumulation of lint around the outdoor ex-

haust opening and in the surrounding area.

Exhaust Direction

Directional exhausting can be accom-

plished by installing a quick-turn 90° dryer

vent elbow directly to exhaust outlet of

dryer. Dryer vent elbows are available

through your local parts distributor or

hardware store.

Exhaust system requirements, continued

Number of 90° turns

MAXIMUM LENGTH

of 4” (102 mm) Rigid Metal Duct

VENT HOOD TYPE

(Preferred)

4”

(10.2 cm) louvered

2.5”

(6.35 cm)

0 125 ft. (38 m) 110 ft. (33.5 m)

1 115 ft. (35 m) 100 ft. (30.5 m)

2 105 ft. (32 m) 90 ft. (27.5 m)

3 95 ft. (29 m) 80 ft. (24.5 m)

4 85 ft. (26 m) 70 ft. (21.5 m)

See also CLEARANCE

REQUIREMENTS.

WARNING

FIRE HAZARD

A clothes dryer must be exhausted

outdoors. DO NOT exhaust dryer into

a chimney, a wall, a ceiling, an attic, a

crawl space or any concealed space of

a building. A clothes dryer produces

combustible lint. If the dryer is not ex-

hausted outdoors, some ﬁne lint will be

expelled into the laundry area. An accu-

mulation of lint in any area of the home

can create a health and ﬁre hazard.

WARNING

FIRE HAZARD

• DO NOT allow combustible materi-

als (for example: clothing, draperies/

curtains, paper) to come in contact

with exhaust system. The dryer MUST

NOT be exhausted into a chimney,

a wall, a ceiling, or any concealed

space of a building which can accu-

mulate lint, resulting in a ﬁre hazard.

• DO NOT screen the exhaust ends of

the vent system, or use any screws,

rivets or other fasteners that extend

into the duct to assemble the exhaust

system. Lint can become caught in

the screen, on the screws or rivets,

clogging the duct work and creating a

ﬁre hazard as well as increasing drying

times. Use an approved vent hood to

terminate the duct outdoors, and seal

all joints with metal foil tape. All male

duct pipe ﬁttings MUST be installed

downstream with the ﬂow of air.

WARNING

Exceeding the length of duct pipe

or number of elbows allowed in the

“MAXIMUM LENGTH” charts can cause an

accumulation of lint in the exhaust system.

Plugging the system could create a ﬁre

hazard, as well as increase drying times.

WARNING

FIRE HAZARD

• DO NOT install ﬂexible plastic or

ﬂexible foil venting material.

• DO NOT exceed 8 ft. (2.4 m)

duct length if installing semi-

rigid venting.

NOTE

Use of 90° quick-

turn elbow required to

meet minimum installation depth.

9

Installation Requirements

In installations where the exhaust system

is not described in the charts, the following

method must be used to determine if the

exhaust system is acceptable:

Exhaust system requirements, continued

Correct Incorrect

Install male fittings in correct direction:

1. Connect an inclined or digital manom-

eter between the dryer and the point

the exhaust connects to the dryer.

2. Set the dryer timer and temperature to

air ﬂuff (cool down) and start the dryer.

3. Read the measurement on the ma-

nometer.

4. The system back pressure MUST

NOT be higher than 1.0 inch of water

column. If the system back pressure is

less than 1.0 inch of water column, the

system is acceptable. If the manometer

reading is higher than 1.0 inch of water

column, the system is too restrictive

and the installation is unacceptable.

Although vertical orientation of the exhaust

system is acceptable, certain extenuating

circumstances could affect the perfor-

mance of the dryer:

• Only the rigid metal duct work should

be used.

• Venting vertically through a roof may ex-

pose the exhaust system to down drafts

causing an increase in vent restriction.

• Running the exhaust system through an

uninsulated area may cause condensa-

tion and faster accumulation of lint.

• Compression or crimping of the exhaust

system will cause an increase in vent

restriction.

• The exhaust system should be

inspected and cleaned a minimum of

every 18 months with normal usage.

The more the dryer is used, the more

often you should check the exhaust sys-

tem and vent hood for proper operation

and that it is free of obstructions.

Manufactured or mobile home installation

1. Installation MUST conform to current

Manufactured Home Construction &

Safety Standard, Title 24 CFR, Part

32-80 (formerly the Federal Standard

for Mobile Home Construction and

Safety, Title 24, HUD Part 280) or

Standard CAN/CSAZ240 MH.

2. Dryer MUST be exhausted outside

(outdoors, not beneath the mobile

home) using metal ducting that will not

support combustion. Metal ducting

must be 4 inches (10.16 cm) in diam-

eter with no obstructions. Rigid metal

duct is preferred.

3. If dryer is exhausted through the ﬂoor

and area beneath the mobile home is

enclosed, the exhaust system MUST

terminate outside the enclosure with

the termination securely fastened to a

non-combustible portion of the mobile

home structure.

4. Refer to previous sections in this guide

for other important exhaust venting

system requirements.

5. When installing a gas dryer into a mo-

bile home, a provision must be made

for outside make up air. This provision

is to be not less than twice the area of

the dryer exhaust outlet.

6. Installer MUST anchor this (1) dryer

or (2) dryer mounted on pedestal to

the ﬂoor with approved Mobile Home

Installation Kit - P/N 137067200.

WARNING

FIRE HAZARD

DO NOT install the dryer where gasoline

or other ﬂammables are kept or stored. If

the dryer is installed in a garage, it must

be a minimum of 18 inches (45.7 cm)

above the ﬂoor. Failure to do so can re-

sult in death, explosion, ﬁre or burns.

10

Installation Requirements

MIN INSTALLATION CLEARANCES -

Inches (cm)

Sides Rear Top Front

Alcove 0” (0 cm) 0” (0 cm)* 0” (0 cm) n/a

Under-

Counter

0” (0 cm) 0” (0 cm)* 0” (0 cm) n/a

Closet 0” (0 cm) 0” (0 cm)* 0” (0 cm)

1”

(2.5 cm)

Clearance requirements

60 sq. in.

(387.1cm²)

3"

(7.6cm)

60 sq. in.

(387.1cm²)

3"

(7.6cm)

Installation In A Recess Or

Closet

1. A dryer installed in a bedroom,

bathroom, recess or closet, MUST be

exhausted outdoors.

2. No other fuel burning appliance shall

be installed in the same closet as the

gas dryer.

3. Your dryer needs the space around it

for proper ventilation.

DO NOT install your dryer in a closet

with a solid door.

4. Closet door ventilation required: A

minimum of 120 square inches (774.2

cm²) of opening, equally divided at the

top and bottom of the door, is required.

Openings should be located 3 inches

(7.6 cm) from bottom and top of door.

Openings are required to be unobstruct-

ed when a door is installed. A louvered

door with equivalent air openings for the

full length of the door is acceptable.

closet door

•F

or other than straight back venting, a quick-

turn 90° dryer vent elbow must be installed to

achieve 0” (0 cm) installation.

0"

(0 cm)

0"

(0 cm)

1"

(2.5 cm)

0"

(0 cm)

NOTE

To achieve an installation with 0” (0

cm) clearance for the back of the dryer

(for other than straight back venting), a

quick-turn 90° dryer vent elbow must be

installed as described previously in this

manual.

IMPORTANT

DO NOT INSTALL YOUR DRYER:

1. In an area exposed to dripping water

or outside weather conditions.

2. In an area where it will come in con-

tact with curtains, drapes, or anything

that will obstruct the ﬂow of combus-

tion and ventilation air.

3. On carpet. Floor MUST be solid with

a maximum slope of 1 inch (2.5 cm).

11

Installation Requirements

Dryer dimensions

* Connection of water inlet hose on steam dryer adds 3/4 in. (2 cm) to installation depth.

1

Power supply cord length on gas dryer or electric Canadian dryer approximately 60

inches (152.5 cm).

2

Drain hose length on washer approximately 59 inches (150 cm).

3

Power supply cord length on washer approximately 60 inches (152.5 cm).

electrical

supply on

rear of unit

1

gas supply

pipe on rear

of gas unit

centerline

height of

rear vent

53.2” (135 cm)*

to clear open door

31.6” (80 cm)*

to front of closed door

27.0”

(68.5 cm)

ﬂoor line

freestand dryer

on ﬂoor

dryer mounted on

optional pedestal

38.0”

(96.5 cm)

53.25”

(135.5 cm)

17.0”

(43 cm)

19.0”

(48 cm)

3.7”

(9.5

1.5”

(4 cm)

3.75”

(9.5 cm)

electrical

supply on

rear of unit

1

gas supply

pipe on rear

of gas unit

centerline

height for

rear vent

53.5” (136 cm)*

to clear open door

32.0” (81.25 cm)*

to front of closed door

75.75”

(192.5 cm)

41.0”

(105 cm)

39.0”

(99 cm)

water supply

connection on

rear of unit

drain hose on

rear of unit

2

power cord on

rear of unit

3

ﬂoor line

approved stacking

kit (STACKIT7X)

required for

stacked installation

13.5”

(34.5 cm)

to center of

rear vent

12

Installation Instructions

Electrical installation

The following are speciﬁc requirements for

proper and safe electrical installation of

your dryer. Failure to follow these instruc-

tions can create electrical shock and/or a

ﬁre hazard.

Grounding requirements -

Electric dryer (USA)

For a grounded, cord-connected

dryer:

1. The dryer MUST be grounded. In the

event of a malfunction or breakdown,

grounding will reduce the risk of electri-

cal shock by providing a path of least

resistance for electrical current.

2. After you purchase and install a 3 wire

or 4 wire power supply cord having an

equipment-grounding conductor and a

grounding plug that matches your wir-

ing system, the plug MUST be plugged

into an appropriate, copper wired

receptacle that is properly installed and

grounded in accordance with all local

codes and ordinances. If in doubt, call

a licensed electrician.

3. DO NOT modify the plug you’ve in-

stalled on this appliance. If it will not ﬁt

the outlet, have a proper outlet installed

by a qualiﬁed electrician.

For a permanently connected dryer:

The dryer MUST be connected to a

grounded metal, permanent wiring system;

or an equipment grounding conductor

must be run with the circuit conductors

and connected to the equipment-ground-

ing terminal or lead on the appliance.

WARNING

ELECTRICAL SHOCK HAZARD

• This appliance MUST be properly

grounded. Electrical shock can result

if the dryer is not properly grounded.

Follow the instructions in this manual

for proper grounding.

• DO NOT use an extension cord with

this dryer. Some extension cords

are not designed to withstand the

amounts of electrical current this dryer

utilizes and can melt, creating electri-

cal shock and/or ﬁre hazard. Locate

the dryer within reach of the recep-

tacle for the length power cord to be

purchased, allowing some slack in

the cord. Refer to the pre-installation

requirements in this manual for the

proper power cord to be purchased.

WARNING

Improper grounding of the dryer may

cause serious injury or death. Check with

a licensed electrician if you are in doubt

as to whether the appliance is properly

grounded.

WARNING

ELECTRICAL SHOCK HAZARD

• A U.L.-approved strain relief must be

installed onto power cord. If the strain

relief is not attached, the cord can

be pulled out of the dryer and can

be cut by any movement of the cord,

resulting in electrical shock.

• DO NOT use an aluminum wired

receptacle with a copper wired

power cord and plug (or vice versa).

A chemical reaction occurs between

copper and aluminum and can cause

electrical shorts. The proper wiring

and receptacle is a copper wired

power cord with a copper wired

receptacle.

NOTE

Dryers operating on 208 volt power supply

will have longer drying times than dryers

operating on 240 volt power supply.

13

Installation Instructions

Grounding requirements -

Electric dryer (Canada)

Grounding requirements -

Gas dryer (USA and Canada)

For a grounded, cord-connected

dryer:

1. The dryer MUST be grounded. In the

event of a malfunction or breakdown,

grounding will reduce the risk of electri-

cal shock by providing a path of least

resistance for electrical current.

2. Since your dryer is equipped with

a power supply cord having an

equipment-grounding conductor and

a grounding plug, the plug must be

plugged into an appropriate outlet that

is properly installed and grounded in

accordance with all local codes and

ordinances. If in doubt, call a licensed

electrician.

3. DO NOT modify the plug provided with

this appliance. If it will not ﬁt the outlet,

have a proper outlet installed by a

qualiﬁed electrician.

1. The dryer is equipped with a three-

prong (grounding) plug for your protec-

tion against shock hazard and should

be plugged directly into a properly

grounded three-prong receptacle.

2. The plug must be plugged into an

appropriate outlet that is properly

installed and grounded in accordance

with all local codes and ordinances. If

in doubt, call a licensed electrician.

3. DO NOT modify the plug provided with

this appliance. If it will not ﬁt the outlet,

have a proper outlet installed by a

qualiﬁed electrician.

WARNING

Improper grounding of the dryer may

cause serious injury or death. Check with

a licensed electrician if you are in doubt

as to whether the appliance is properly

grounded.

Grounding type wall receptacle

Power cord with

3-prong grounded plug

Do not, under

any circumstances,

cut, remove,

or bypass the

grounding prong.

WARNING

Improper grounding of the dryer may

cause serious injury or death. Check with

a licensed electrician if you are in doubt

as to whether the appliance is properly

grounded.

14

Electrical connection

(non-Canada) - 3 wire cord

Installation Instructions

1. Turn off power supply to outlet.

2. Remove the screw securing the ter-

minal block access cover in the lower

corner on the back of the dryer.

3. Install a UL-approved strain relief

according to the power cord/strain

relief manufacturer’s instructions in the

power cord entry hole below the ac-

cess panel. At this time, the strain relief

should be loosely in place.

4. Thread an UNPLUGGED, UL-ap-

proved, 30 amp. power cord, NEMA

10-30 type SRDT, through the strain

relief.

5. Attach the power cord neutral (center

wire) conductor to the SILVER colored

center terminal on the terminal block.

Tighten the screw securely.

6. Attach the remaining two power cord

outer conductors to the outer, BRASS

colored terminals on the terminal block.

Tighten both screws securely.

3-wire receptacle

(NEMA type 10-30R)

Access

Cover Screw

Terminal

Block

Line 2

(BRASS Terminal)

Neutral

(SILVER Terminal)

Line 1

(BRASS Terminal)

Internal Ground

(GREEN Screw)

Install UL-Approved

Strain Relief Here

Terminal Screw

Recovery Slot

Neutral

(center wire)

30 AMP

NEMA 10-30

7. Follow manufacturer’s guidelines for

ﬁrmly securing the strain relief and

power cord.

8. Reinstall the terminal block cover.

DO NOT remove

internal ground in

a 3-wire system!!

Neutral

terminal

NOTE

If a terminal screw falls during cord

installation, it can be retrieved in the

terminal screw recovery slot below the

access panel.

WARNING

ELECTRICAL SHOCK HAZARD

Failure to disconnect power source be-

fore servicing could result in personal

injury or even death.

WARNING

ELECTRICAL SHOCK HAZARD

DO NOT make a sharp bend or crimp

wiring/conductor at connections.

IMPORTANT

If moving dryer from a 4-wire system and

installing it in a 3-wire system, move the

internal ground from the center terminal

back to the GREEN screw next to the

terminal block.

WARNING

ELECTRICAL HAZARD

Label all wires prior to disconnection when

servicing controls. Wiring errors can cause

improper and dangerous operation. Verify

proper operation after servicing.

15

Installation Instructions

Electrical connection

(non-Canada) - 4 wire cord

Access

Cover Screw

Terminal

Block

Line 2

(BRASS Terminal)

Neutral

(SILVER Terminal)

Line 1

(BRASS Terminal)

Internal Ground

(GREEN Screw)

Install UL-Approved

Strain Relief Here

Terminal Screw

Recovery Slot

4-wire receptacle

(NEMA type 14-30R)

1. Turn off power supply to outlet.

2. Remove the screw securing the ter-

minal block access cover in the lower

corner on the back of the dryer.

3. Install a UL-approved strain relief

according to the power cord/strain

relief manufacturer’s instructions in the

power cord entry hole below the ac-

cess panel. At this time, the strain relief

should be loosely in place.

4. Thread an UNPLUGGED, UL-ap-

proved, 30 amp. power cord, NEMA

14-30 type DRT or SRDT, through the

strain relief.

5. Disconnect the internal (WHITE) dryer

harness ground wire from the (GREEN)

ground screw next to terminal block.

6. Attach the ground (GREEN) power

cord wire to the cabinet with the

ground (GREEN) screw. Tighten the

screw securely.

7. Move the internal dryer harness ground

(WHITE) wire to the terminal block and

attach it along with the neutral (WHITE)

power cord wire conductor to center,

SILVER colored terminal on the terminal

block. Tighten the screw securely.

8. Attach the RED and BLACK power

cord conductors to the outer, BRASS

colored terminals on the terminal block.

Tighten both screws securely.

Neutral

(WHITE

wire)

30 AMP

NEMA 14-30

Ground

(GREEN

wire)

9. Follow manufacturer’s guidelines for

ﬁrmly securing the strain relief and

power cord.

10. Reinstall the terminal block cover.

Move internal ground (WHITE)

wire to neutral (SILVER)

terminal for 4-wire system.

Neutral

terminal

GREEN

ground screw

BLACK or

RED power wire

BLACK

or RED

power wire

GREEN

ground wire

WHITE

neutral wire

WARNING

ELECTRICAL SHOCK HAZARD

Failure to disconnect power source be-

fore servicing could result in personal

injury or even death.

WARNING

ELECTRICAL SHOCK HAZARD

DO NOT make a sharp bend or crimp

wiring/conductor at connections.

NOTE

If a terminal screw falls during cord instal-

lation, it can be retrieved in the terminal

screw recovery slot below the access

panel.

WARNING

ELECTRICAL HAZARD

Label all wires prior to disconnection when

servicing controls. Wiring errors can cause

improper and dangerous operation. Verify

proper operation after servicing.

16

Installation Instructions

Gas connection

1. Remove the shipping cap from gas

pipe at the rear of the dryer.

2. Connect a 1/2 inch (1.27 cm) I.D.

semi-rigid or approved pipe from gas

supply line to the 3/8 inch (0.96 cm)

pipe located on the back of the dryer.

Use a 1/2 inch to 3/8 inch (1.27 cm to

0.96 cm) reducer for the connection.

Apply an approved thread sealer that is

resistant to the corrosive action of lique-

ﬁed gases on all pipe connections.

3. Open the shutoff valve in the gas sup-

ply line to allow gas to ﬂow through

the pipe. Wait a few minutes for gas to

move through the gas line.

All connections must be wrench-tightened

Flare

Union

Flare

Union

Manual

Shutoff

Valve

Closed

Open

Flexible

Connector

GAS FLOW

Inlet Pipe on

Back of Dryer

Nipple

Shutoff Valve - Open position

to dryer

from gas supply

4. Check for gas system leaks with a ma-

nometer. If a manometer is not avail-

able, test all connections by brushing

on a soapy water solution.

IMPORTANT

DO NOT connect the dryer to L.P. gas

service without converting the gas valve.

An L.P. conversion kit must be installed

by a qualiﬁed gas technician.

WARNING

EXPLOSION HAZARD

NEVER test for gas leaks with an open

ﬂame.

IMPORTANT

Installation to the gas service must follow

local codes and ordinances and the lat-

est edition of the National Fuel Gas Code

ANSI Z223.1/NFPA 54 or in Canada,

CSA B149.1.

IMPORTANT

The supply line must be equipped with

an approved manual shutoff valve. This

valve should be located in the same room

as the dryer and should be in a location

that allows ease of opening and closing.

DO NOT block access to the gas shutoff

valve.

Water connection

(Steam Model only)

Water Supply Requirements

Cold water faucet MUST be installed

within 42 inches (107 cm) of your dryer’s

water inlet. The faucet MUST be 3/4

inch (1.9 cm) with threading for laundry

hose connection. Water pressure MUST

be between 20 and 120 psi. Your water

department can advise you of your water

pressure.

1. Turn off COLD water supply to washer.

2. Remove COLD inlet hose from COLD

water supply and inspect for rubber

washer.

Replace washer if it is torn or worn

out.

17

Rubber Washers

MUST BE PRESENT

NOTE

If you were able to install the “Y” connec-

tor directly to the COLD water supply,

please skip to step 8.

Installation Instructions

Direct Connection

or with Extension

Water Inlet

on Dryer

Cold Water Supply

Hose to Washer

6. If there is not room to install the “Y”

connector directly, thread the short

extension hose on to the COLD water

supply and snug it by hand; then

tighten it another 2/3 turn with pliers.

7. Thread the “Y” connector to the short

extension hose and snug it by hand;

then tighten it another 2/3 turn with

pliers.

8. Connect the COLD inlet hose for the

washer to the “Y” connector and snug

it by hand; then tighten it another 2/3

turn with pliers.

9. Connect the straight end of the long

hose from the kit to the other outlet

on the “Y” connector and snug it by

hand. Connect the hose’s 90° cou-

pling to the brass water inlet on the

back of the dryer and snug it by hand.

Tighten each connection of the dryer

inlet hose another 2/3 turn with pliers.

Water connection, continued

(Steam Model only)

4. Remove hose kit from dryer drum

and inspect hose couplings for proper

placement of rubber washers.

3. Momentarily turn on COLD supply

and run some water into a bucket or

container to clear any contaminants in

the line.

5. If your installation has room for the

COLD water supply to accept the “Y”

connector directly, thread the “Y” con-

nector to the COLD water supply and

snug it by hand; then tighten it another

2/3 turn with pliers.

10. Turn on the water and check for leaks

at all connections.

Cold Inlet Hose

to Washer

Rubber Washer

Must be Present

and Undamaged

18

Installation Instructions

General installation

1. Connect the exhaust duct to the out-

side exhaust system. Use of a 4” (102

mm) clamp (item A) is recommended to

connect the dryer to the exhaust vent

system. Use metal foil tape to seal all

other joints.

2. Use a carpenter’s level to level your

dryer front-to-back and side-to-side.

3. Use adjustable pliers to adjust the

leveling legs so the dryer is level front-

to-rear and side-to-side, and stable

corner-to-corner.

4. Press down on alternate corners and

sides and feel for the slightest move-

ment. Adjust the appropriate leg(s) so

the dryer sits solidly on the ﬂoor on

ALL four legs. Keep the leveling leg

extension at a minimum for best perfor-

mance of the dryer.

5. Plug the power cord into a grounded

outlet.

CAUTION

When discarding or storing your old dry-

er, remove the door.

IMPORTANT

Be sure the power is off at a circuit

breaker/fuse box before plugging the

power cord into an outlet.

6. Turn on the power at the circuit

breaker/fuse box.

7. Read the Use & Care Guide provided

with the dryer. It contains valuable and

helpful information that will save you

time and money.

8. If you have any questions during initial

operation, please review the “Avoid

Service Checklist” in your Use & Care

Guide before calling for service.

9. Place these instructions in a location

near the dryer for future reference.

NOTE

A wiring diagram and technical data

sheet are located under the dryer top

panel.

WARNING

Improper grounding of the dryer may

cause serious injury or death. Check with

a licensed electrician if you are in doubt

as to whether the appliance is properly

grounded.

19

Screwdriver

with #2

square bit

Reversing Door

Removing Latch and Hole Plugs

1. Open the door.

2. Remove plastic hole plugs and save to

reinstall later. You may have to use a

non-scratching plastic knife if you are

unable to dislodge the plugs manually.

3. Remove both screws from door latch.

Save latch and screws for reinstallation

later.

x2

NOTE

Door reversibility is available on all dryer models.

Plastic knife

Tools needed for reversal:

IMPORTANT

BEFORE YOU REVERSE YOUR DRYER

DOOR:

1. Be sure you have adequate swing area

before reversing door.

2. Gather your tools - including a screw

driver with a #2 square bit and plastic

knife (or small, ﬂat prying tool that won’t

damage paint).

3. Be sure dryer is unplugged from power

source!

WARNING

ELECTRICAL SHOCK HAZARD

Failure to disconnect power source before servicing could result in personal injury or

even death.

20

Reversing Door

x2

Reinstalling Door Assembly

1. Rotate the door and hang the upper

hook on the back of the hinge in the

upper hole of the front panel.

Reinstalling Latch and Hole Plugs

1. Install door latch with screws removed

earlier.

Verify Reversed Door Operation

1. Test door for free, smooth swinging

operation and secure latching when

closed.

2. Plug in dryer and close the door. Start

a test cycle: drum should tumble until

door is pulled open or cycle is paused

or canceled.

2. Reinstall and tighten all four screws

removed earlier - two front screws ﬁrst,

then two side screws.

2. Insert plastic hole plugs removed

earlier.

x4

1

2

3

4

Removing Door Assembly

1. Completely open the door to expose all

four hinge screws.

2. Remove all four hinge screws with #2

square bit driver. Save for reinstalling

later.

x4

3. Grasp the door with both hands and

lift slightly as you pull door and hinge

away from the front panel.

La page est en cours de chargement...

Electrolux EFDE317TIW Manuel utilisateur

Electrolux EFDE317TIW Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents