A l l e g r o W a l l M o u n t
I n s t a l l a t i o n G u i d e
Category: Residential and Commercial Metering
Type: Installation Manual
Issue: Operation
Master Meter, Inc. 101 Regency Pkwy, Mansfield, TX 76063 T: 817-842-8000 F: 817-842-8100 MasterMeter.com
1. Introduction
The Allegro Wall mount endpoint for wáter meters provides two-way communication capabilitiblites over the
Allegro RF Network to transmit encoded wáter meter readings, alarms, and other related functions. The Allegro
Wall mount endpoint is battery operated and utilizes an FCC licensed frequency within the 450- 470Mhz band.
The following are the main features of the Allegro Wall mount endpoint:
On request reads for last-time meter reads
Alarm report & data logging
Remote, over-the-air firmware upgrades
Remote unit configurations
Confirmation of network connectivity
2. General Information
Read the instructions below before installing the endpoint.
To prevent injury or damage, do not install, operate, or maintain the endpoint without following the
instructions in this guide.
Store the endpoint in a cool, dry place.
Follow all warnings and instructions marked on the product.
3. Unpacking and handling
Carefully unpack the endpoint and inspect all contents for shipping damage before attempting to install.
If any indication of physical damage is found, immediately contact the responsible transportation service
and your local Master Meter representative.
Avoid hard blows, jolts, or impact to the endpoint.
Master Meter, Inc. 101 Regency Pkwy, Mansfield, TX 76063 T: 817-842-8000 F: 817-842-8100 MasterMeter.com
4. Regulation Information
FCC and Industry Canada Class B Digital Device Notice
The digital circuit of this device has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
CAN ICES-3 (B)/NMB-3(B)
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numerique de la classe B est conforme a la norme NMB-003 du Canada.
Industry Canada interference Notice
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of
the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage;
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
FCC interference Notice
This device complies with part 90 of the FCC rules.
Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of
the device.
FCC and Industry Canada Radiation Hazard Warning
WARNING! To comply with FCC and IC RF exposure compliance requirements, the device should be located
at a distance of at least 20 cm from all persons during normal operation. The antennas used for this product
must not be co-located or operated in conjunction with any other antenna or transmitter.
Le dispositif doit être placé à une distance d'au moins 20 cm à partir de toutes les personnes au cours de son
fonctionnement normal. Les antennes utilisées pour ce produit ne doivent pas être situés ou exploités
conjointement avec une autre antenne ou transmetteur.
WARNING! Changes or modifications to this equipment not expressly approved by the party responsible for
compliance (ST Engineering Telematics Wireless Ltd.) could void the user’s authority to operate the equipment.
Master Meter, Inc. 101 Regency Pkwy, Mansfield, TX 76063 T: 817-842-8000 F: 817-842-8100 MasterMeter.com
5. Product Specifications
Figure 1) Specification Tables
Dimensions
Length x width x height
Inches
5.2 x 3.6 x 2
Weight
Product Weight
Lbs
2.2
Environment (worst case)
Submerge time (@0°, 25°, 40°C)
Hours
168
Temperature Operating temperature range for basic operation (transmission of
last 12 reads, no data logger transmission)
°C -20 to 65
Operating temperature range for data logger transmission
°C
-
10 to 65
Storage temperature range
°C
-
30 to 80
Humidity
Maximal humidity at temperature of 65 °C
%
95
Chemical exposure
Oliec acid + Hydraulic oils + Fuel+ Other Chemicals
Hours
72
Connector Types
Nicor, Bare Wire
Regulatory
UL, FCC, IC
Figure 2) Encoder Compatibility List
Master Meter
Elinx, AccuLinx Digital Encoders All Sizes
Sensus
ICE, Ipearl, Accustream Digital Encoders All Sizes
Mueller
Mueller Translator Register All Sizes
Neptune
ARB II
–
VI Encoded Registers
Figure 3) LED Indicator Behavior
Mode Details LED
Magnet sensing LED should indicate in case of magnet sensing 5 seconds slow blinks
(1sec on / 1 sec off)
Fast mode Indication when unit enters to fast mode 5 seconds fast blinks
(0.5Sec on / 05sec off)
Magnet release Indication for magnet release, 8 seconds after magnet
sensing
1 blink, 2 seconds duration
Install mode no parent After magnet removal when unit enters to install mode
and no parent acquirement
5 seconds slow blinks
(1sec on / 1 sec off)
Install mode after parent
acquirement
Unit acquired a parent, and it still in install mode 2 seconds fast blinks
(0.5Sec on / 05sec off)
Normal mode Device is associated to a parent, got configuration from
Command center.
5 seconds fast blinks
(0.5Sec on / 05sec off)
Master Meter, Inc. 101 Regency Pkwy, Mansfield, TX 76063 T: 817-842-8000 F: 817-842-8100 MasterMeter.com
6. Installation Requirements
Step 1)
Remove the Meter Pit Lid
Step 2)
Remove threaded locking mechanism
Step 3)
Pass the cable through the Lid hole and install the Allegro Wall mount endpoint into the Pit lid. If
mounting brackets are available beneath the meter pit lid, the endpoint may alternatively be
installed in this manner.
Step 4)
Fasten the endpoint to the meter pit lid using the threaded locking mechanism
Step 5)
Attach the Allegro Wall mount endpoint to the encoded water meter using the appropriate Nicor
or Bare Wire connections
Step 6)
Activate the Allegro Wall mouont endpoint using a magnet or Allegro Activator tool
Step 7)
Verify Status using the LED Indicators located at the bottom of the endpoint’s neck
-
1
-
2
-
3
-
4
-
5
Master Meter 40685 Guide d'installation
- Taper
- Guide d'installation
- Ce manuel convient également à
dans d''autres langues
Autres documents
-
SyberSense XPT01E1433 Mode d'emploi
-
Xylem FLXI2102 Mode d'emploi
-
Extron NAV E 201 D Manuel utilisateur
-
Extron NAV 10E 201 D Mode d'emploi
-
ST Engineering MIU1USLA Meter Interface Unit Manuel utilisateur
-
Universal Remote Control Remote control HCCUR Le manuel du propriétaire
-
Ohaus STARTER 5000 Manuel utilisateur
-
CARLO GAVAZZI UWPAM1US1L2X Guide d'installation
-
-
