brondell EM617-EW Le manuel du propriétaire

Owner’s Manual

ADVANCED BIDET SEAT

SWASH BL97 / EM617

2

This manual contains important safety information.

Before operating the bidet, please read this manual

thoroughly, and retain it for future reference.

PRODUCT INSTALLATION

GENERAL INFO

PRODUCT OPERATION

01 SAFETY INFORMATION

06

07

08

PRODUCT INFORMATION

Product Features

Product Dimensions

Product Parts

09

10

11

13

PRODUCT INSTALLATION

Installation Parts

Before Installation

Swash Installation

Remote Control Installation

External Bidet Filter Installation

14

16

17

18

OPERATING THE SWASH

BL97 / EM617 Remote Control

BL97 / EM617 Auxiliary Control Panel

Using the BL97 / EM617

Special Mode Operations

TECHNICAL INFO

TRANSLATIONS

21 PRODUCT SPECIFICATIONS

22

23

MAINTENANCE

Seat Cleaning & Removal

Nozzle Cleaning

Cleaning the Mesh Filter

Product Storage

24 TROUBLESHOOTING

27 WARRANTY

28 CONTACT

1ENGLISH

29 SPANISH

58 FRENCH

BL97 / EM617 OWNER'S MANUAL

Table of Contents

1

SAFETY INFORMATION

(IMPORTANT SAFEGUARDS)

READ ALL INSTRUCTIONS BEFORE USING

BE CAREFUL TO KEEP THIS SAFETY INFORMATION. PLEASE READ THIS INFORMATION TO PREVENT

PROPERTY LOSS AND ENSURE SAFETY.

DANGER: If not observed, serious injury or even death may occur as a result.

WARNING: If not observed, serious physical injury or property damage may occur as a result.

CAUTION: If not observed, minor physical injury or property damage may occur as a result.

DANGER Failure to observe the following warnings may result in electric shock, ﬁre,

personal injury, property damage or product damage.

• Do not use a damaged power plug or plug into a loose electric outlet.

• Do not move the product by pulling the power cord.

• Do not handle the product or power plug with wet hands.

• Do not forcefully bend the power cord or place heavy objects on it to prevent it from being

damaged or deformed.

• Do not connect and pull out the power plug or cord repeatedly.

• Unplug the product before cleaning, repairing, inspecting, or replacing parts.

• Remove any dust or water from the power plug prior to plugging in.

• Do not plug the product into an electrical outlet or power strip that is being used by too many

other products. Use an electrical outlet adequate for the wattage of the product rated for a

minimum of 15 amps.

• If the power cord is damaged, do not attempt to repair, modify, or replace the cord yourself.

Contact the Brondell Service Center toll free at 888-542-3355 or email us through our website.

• If the product produces a strange noise, a burning smell, or emits smoke, unplug it immediately

from the electrical outlet and contact Brondell. Failure to do so may result in electric shock or ﬁre.

• Do not insert any wires or sharp objects into any product gaps. This may result in electric shock,

ﬁre, or product damage.

• Do not place an electronic or gas heater near the product or dispose of any burning materials

such as a lit cigarette in the toilet. This may result in ﬁre or product deformation. Do not place any

containers ﬁlled with water or other liquids, food, metallic objects, or any ﬂammable material on

top of the product. If foreign material enters the product, this may result in electric shock or ﬁre.

SAVE THESE INSTRUCTIONS

2

• Do not plug in, operate, or store the unit in locations where ﬂammable or combustible materials are

used or kept.

• Do not use industrial water, or gray water for the supply, as this may cause skin damage or disease.

• Turn o the main water supply valve when cleaning.

• For children and seniors who may have diculties with adjusting temperatures or those with

sensitive skin or impaired heat sensitivity, set the temperature of the wash spray and seat to “low”

or “o” to prevent burning.

• Close supervision is necessary when this product is used by children, seniors, or persons requiring

general assistance.

• Do not press the buttons using excessive force.

• Do not stand on top of or place any heavy objects onto the seat cover.

• Use this product for its intended use only, as described in this manual. Do not use any attachments

that are not recommended by Brondell.

SAVE THESE INSTRUCTIONS

SAFETY INFORMATION

(IMPORTANT SAFEGUARDS)

DANGER Failure to observe the following warnings may result in electric shock, ﬁre,

personal injury, property damage or product damage.

• Do not use the product in locations exposed to excessive moisture and do not splash water

onto the product.

• While cleaning the bathroom, pull the power plug out of the electrical outlet and exercise

caution to ensure that water or cleaning supplies do not splash onto the bidet. Failure to do so

may result in electric shock or ﬁre.

• If foreign material enters the product, pull the power plug out of the electrical outlet, turn o

the main water valve, and call the Brondell Service Center.

• Do not disassemble, repair, or modify the product yourself.

• Do not use the product while wet from bathing or showering.

• Do not place or store the product where it can fall or be pulled into a tub or sink.

• Do not place in or drop the product into water or any other liquid.

• Do not reach for the product if it has fallen into water. Unplug the product immediately and call

the Brondell Service Center.

• Do not use the product if it is not working properly. Please unplug the product immediately,

close the main water supply valve, and call the Brondell Service Center at 888-542-3355.

Failure to do so may result in electric shock, ﬁre, or ﬂooding.

WARNING Failure to observe the following warnings may result in electric shock, ﬁre,

personal injury, property damage or product damage.

3

SAVE THESE INSTRUCTIONS

• Do not connect the main water supply to the hot water pipe or supply (only connect to the

cold water supply).

• After the installation, make sure to check all water supply connections for leaks. Rubber

washers should be in place for the water connection hoses & T-Valve.

• Do not open/close the seat or seat cover with excessive force.

• Exercise caution that urine does not come into contact with the product - failure to do so may

result in bad odors or malfunction.

• If the product will not be used for a long period of time, unplug the power cord, close the

main water supply valve, and drain any water in the water tank.

• Do not pull out the bidet hose using excessive force.

• Do not use thinner, benzene, acidic chemicals, chloride, or hydrochloric acid detergent on or

near the product. This may result in corrosion to the metal parts or discoloration or scratches

to the bidet body.

• This appliance is not intended for use by persons (including children and seniors) with

reduced physical, sensory, or mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction concerning the use of the appliance by

a person responsible for their safety.

• Children should be supervised to ensure that they do not play with the appliance.

• Never operate this product if it has a damaged cord or plug, if it is not working properly, if it

has been dropped or damaged, or dropped into water. Contact the Brondell Service Center for

examination and repair.

• Keep the cord away from heated surfaces and heating vents.

• Never block the air openings of the product or place it on a soft surface, such as a bed or couch,

where the air openings may be blocked. Keep the air openings free of lint, hair, etc.

• Never drop or insert any object into any opening or hose.

• Do not use the product outdoors or operate where aerosol (spray) products are being used or a

room where it could be exposed to oxygen.

• Connect this product to a properly grounded outlet only. Refer to the Grounding Instructions in

the next pages of the manual.

SAFETY INFORMATION

(IMPORTANT SAFEGUARDS)

WARNING Failure to observe the following warnings may result in electric shock, ﬁre,

personal injury, property damage or product damage.

CAUTION Failure to observe the following warnings may result in electric shock, ﬁre,

personal injury, property damage or product damage.

4

SAFETY INFORMATION

(IMPORTANT SAFEGUARDS)

Ground GFCI Outlet

ATTENTION

This product should only be used with a grounded GFCI (Ground Fault

Circuit Interrupter) outlet and a grounded three-prong electrical cord

as shown to the right. In the event of an electrical short circuit, using a

grounded GFCI outlet reduces the risk of electric shock.

This product is equipped with a grounded cord and is for use on a

nominal 120V circuit only (minimum 15 amps) and must be plugged

into an outlet that is properly grounded with a GFCI breaker as shown.

Replace or repair a damaged cord immediately.

Test

Reset

Grounding Pin

IMPROPER USE OF THE GROUNDING PLUG CAN RESULT

IN A RISK OF ELECTRIC SHOCK.

• If repair or replacement of the cord or plug is necessary,

do not connect the grounding wire to either ﬂat blade

terminal. The wire with green insulation (either with or

without a yellow stripe) is the grounding wire.

• Check with a qualiﬁed electrician if the grounding

instructions are not completely understood, or if there is

doubt if the product is properly grounded.

For those with certain medical or mobility issues in the bathroom,

we recommend our Swash 1400 or Swash 1000 bidet seats, as their

mounting systems are engineered for the most secure transitions from

wheelchairs or walkers.

GROUNDING AND GFCI OUTLET INSTRUCTIONS

SAVE THESE INSTRUCTIONS

DANGER Improper use of the grounding plug can result in a risk of electric shock.

5

DANGER Do not connect the grounding wire to a

non-grounded outlet.

SAVE THESE INSTRUCTIONS

OPTIONAL GROUNDING INSTRUCTIONS

SAFETY INFORMATION

(IMPORTANT SAFEGUARDS)

This product is for use on a nominal 120V circuit, and has a grounding

plug that looks like the plug illustrated in sketch A in Figure 1.

A temporary adapter, which looks like the adapter illustrated in

sketches B and C, may be used to connect this plug to a 2-pole

receptacle as shown in sketch B if a properly grounded outlet is

not available.

The temporary adapter should be used only until a properly grounded

outlet (sketch A) can be installed by a qualiﬁed electrician.

A

B

D

C

Figure 1

Figure 2

Attach the grounding wire to the grounding screw on the product as

shown in sketch D of Figure 2. Attach the other end of the grounding

wire to the grounding screw located on the temporary outlet.

6

Stainless Steel Nozzle

Stainless Steel resists soiling and bacterial

contamination for enhanced hygiene.

Posterior and Feminine Warm Water Wash

Experience the ultimate in clean with

adjustable temperature, position, pressure,

massage, and oscillation settings.

Strong Wash

Concentrated stream with adjustable

pressure, position, temperature, massage, and

oscillation settings.

Positionable Nozzle

The nozzle has ﬁve dierent positions

to ensure the most comfortable and

complete wash.

Adjustable Water Temperature and Pressure

Front, Rear and Strong wash modes have four

available water temperature settings, and ﬁve

water pressure settings.

Pulse

When activated, the water pressure

automatically increases and decreases to

provide a pulsating, cleaning spray.

Warm Air Dryer

Includes adjustable temperature with ﬁve

levels for a hands-free experience and

toilet paper reduction – even elimination

(EM617 model only).

PRODUCT INFORMATION

Product Features

Nozzle Oscillation

The Move function provides a massaging,

oscillating cleanse during the wash cycle

ensuring a thorough and comfortable wash.

Gentle Wash Function

Activates a preset wash cycle at the softest

setting for a gentle clean. A drying cycle will

follow on EM617 model only.

Ergonomic Heated Seat

With four temperature settings

(High/Medium/Low/O).

Illuminating Nightlight

The cool blue hue of the nightlight means

no more blinding lights during midnight trips

to the bathroom.

Gentle Closing Seat and Lid

“Slam free” Gentle Closing seat and lid are

user friendly.

Eco Mode

When activated, this function automatically

lowers the water and seat temperature to one

of two dierent settings.

Quick Release Seat

Quick Release button for easy removal and

cleaning of seat and toilet.

7

4.72 in – 8.27 in

Required Distance Between Mounting Holes

15.9 in

8.1 in

11.4 in

8.1 in

20.7 in

19.5 in

10.6 in

Elongated Top View

Round Top View

PRODUCT INFORMATION

Product Dimensions

8

13

1. Lid

2. Seat Sensor

3. Warm Seat

4. Warm Air Dryer (EM617 model only)

5. Nozzle Assembly

6. LED Nightlight

7. Power Plug

8. Remote IR Receiver

9. Water Inlet with Mesh Filter

10. Drain Plug

11. Mounting Plate

12. Quick Release

13. Grounding Wire

PRODUCT INFORMATION

Product Parts

9

1. Mounting Bolt (2)

2. Rubber Cone Washer (2)

3. Flat Washer (2)

4. Nuts (2)

5. Mounting Plate

6. Adjustable Brackets (2)

7. T-Valve Connector with

Rubber Washer

8. Bidet Hose

9. Remote Control

10. Remote Control Wall Mount

11. AAA Batteries (4)

PRODUCT INSTALLATION

Installation Parts

BL97 EM617

10

PRODUCT INSTALLATION

Before Installation

DO NOT PLUG THE PRODUCT IN WHILE THE UNIT IS UPSIDE DOWN

This may cause damage to the internal components.

WATCH OUR INSTALLATION VIDEO

Installation for all Swash products can be found online at brondell.com

CHECK BOLT SPREAD

This bidet seat can only be installed on toilets with a bolt hole spread of 4.72 – 8.27 in.

(see Product Dimensions on page 7 for more information).

CHECK FOR TOP MOUNT INSTALLATION

If your ﬁxture only has top-side access to the mounting bolts that hold the seat to the toilet, you

will likely need to purchase the Swash Bidet Seat Top Mount Hardware Kit, found on brondell.com.

CHECK FOR A CONCEALED TOILET FILL VALVE

Many modern toilets have sleek designs intended to cover and camouﬂage plumbing

connections, which make a standard Swash installation dicult or impossible. For this, we

recommend using our Alternate Swash Bidet Seat T-Valve, found on brondell.com.

CHECK WATER SUPPLY LINE

Check the line that connects the toilet tank to the water shut o valve. If it is a rigid pipe, you may

need to purchase a ﬂexible hose to replace it before installing the Swash. The length of the hose

and the size of the connectors will vary.

RESIDUAL MOISTURE IS NORMAL

Every product is tested with pure water during production to ensure the highest quality and

performance. It is normal to ﬁnd a small amount of residual moisture on the product and in the

reservoir and ﬁlter.

TOOLS

A Phillips head or standard screwdriver may be needed to remove the existing toilet seat and a

standard wrench may be needed for tight water supply connections. Teﬂon tape can be helpful in

creating a water-tight seal between plumbing connections.

11

3. Connect the top of the T-valve to the incoming water connection on

the bottom of your toilet tank.

4. Connect the water supply line coming from the wall to the bottom of

the T-valve.

5. Install Mounting Plate for Standard Installation

a. Place mounting plate over mounting holes on toilet, rubber side

facing down, arrow pointing to the toilet tank.

b. Place adjustable brackets ﬂat side down in the center of the square

opening in the mounting plate and insert mounting bolts through

adjustable brackets and mounting holes. Be sure that the square

mounting bolt head is even with sides of adjustable bracket.

1. Existing Toilet Seat Removal

a. Lift hinge covers and use a screwdriver to remove the

mounting bolts.

b. Remove the toilet seat. Keep for future use.

2. Turn O Water Supply Valve and Flush Toilet

a. Turn water valve o to stop the ﬂow of water.

b. Flush toilet and hold down handle to completely

empty tank.

c. Disconnect water supply hose from toilet tank. Do not

disconnect from the water supply valve.

PRODUCT INSTALLATION

Swash Installation

Please read these instructions carefully before installing the Swash.

Failure to do so could result in ﬂooding, leaking or damage to the product.

NOTE: Steps may vary by type of seat and toilet.

NOTES

• You may wish to place a container under the tank to catch excess water.

• Do not continue without completing the above steps.

• Failure to do so could result in ﬂooding, leaking or damage to the Swash.

NOTES

• The T-valve connects to the ﬁll valve directly under your toilet tank - it

does not connect at the wall.

• Only connect to the cold toilet water supply line.

• If your water supply line is rigid you may need to replace the water

supply line before continuing.

Steps 5b-5c

Steps 3-4

Toilet tank

T-valve

Cold

water

supply

line

Step 2c

12

6. Connect the Bidet Hose to the Seat

Connect the plastic side of the bidet hose to the water inlet.

Hand-tighten to secure. Take care not to twist the bidet hose,

excessively bend it, or strip the plastic screw threads when

screwing the hose onto the bidet seat.

7. Attach the Swash to the Mounting Plate

a. Set the Swash ﬂat on the toilet bowl in front of the mounting

plate, and slide seat onto plate until it is secure.

b. If the seat appears too short or too long for the toilet, adjust

the mounting plate accordingly. To adjust the mounting plate,

loosen the nuts underneath the toilet and slide seat forward

or backwards as needed. Once the seat is lined up properly,

tighten the nuts to hold in place.

8. Connect the open end of the Bidet Hose to the T-Valve.

NOTE: For those with mobility issues, we recommend our Swash 1400

or Swash 1000 bidet seats, as their mounting systems are engineered

for the most secure transitions from wheelchairs or walkers.

9. Turn On Water Supply

a. Open the main water supply valve slowly and check for leaks.

b. Wait 5 minutes, check again and, if there are no leaks, continue.

10. Plug the Power Cord into an Electrical Outlet. Nozzle will extend

and retract.

PRODUCT INSTALLATION

Swash Installation

c. Slide rubber cone washer, ﬂat washer, and then nut onto

mounting bolts under the toilet bowl and tighten to keep

mounting plate in place.

Step 7

Step 6

Step 8

11. Follow instructions on page 17 for using the Swash.

NOTE: Make sure to only use a grounded GFCI (Ground Fault Circuit

Interrupter) electrical outlet. In the case of a short circuit, a grounded

GFCI outlet may help prevent electric shock or injury.

13

Step 1

NOTE: Customers with

hard water, well water, and

softened water can extend

the life of their bidet

seat by purchasing and

installing an external inline

water ﬁlter to be used

with the Swash. The bidet

ﬁlter should be changed

every six months, and can

be purchased online at

brondell.com.

PRODUCT INSTALLATION

Remote Control Installation, External Bidet Filter Installation

1. Turn O Water Supply Valve and Flush Toilet.

a. Turn water valve o to stop the ﬂow of water.

b. Flush toilet and hold down handle to completely empty tank.

2. Disconnect the Bidet Hose from the T-Valve.

3. Connect the female end of the Swash Filter to the open

T-Valve connection.

4. Connect the Bidet Hose to the male end of the Swash Filter.

5. Turn the toilet water supply valve back on.

1. Battery Installation

a. Seperate the remote control from the magnetic dock.

b. Turn remote over and using your ﬁngers or a ﬂat head

screwdriver, gently pry the rear cover o the remote. Insert the

four included AAA batteries and replace rear battery cover.

c. To conﬁrm the batteries are installed correctly, touch the

remote options and lights will turn on.

2. Mount Remote (optional)

a. Identify a location in the bathroom for the remote control that

is visible and reachable from the toilet.

b. Remove the backing from the double stick tape on the back

of the remote wall mount. Make sure the remote mount is fully

secure so that it does not fall and damage the remote control.

c. Place the remote control into the mount.

External Bidet Filter Installation

Remote Control Installation

Step 2

FLOW

Step 3

FLOW

Step 4

14

OPERATING THE SWASH

BL97 Remote Control

14 15

16

9

Pulse

6

Nozzle Position Water Pressure

Gentle Mode

11

10

1

Stop

3

Front Wash / Move

2

Rear Wash / Move

4Strong Wash / Move

User

Memory 1

User

Memory 2

Remote Control IR

Signal Transmitter

Nozzle Cleaning

Seat Temperature 8

12

13

Water

Temperature

Eco Mode

7

15

Nozzle Cleaning

14 15

16

9

Pulse

6

Seat Temperature 8

Nozzle Position

Water Pressure and

Dryer Temperature

(dryer on EM617

model only)

12

Gentle Mode

13

Water

Temperature

11

Eco Mode

10

1

Stop

3

Front Wash / Move

2

Rear Wash / Move

4Strong Wash / Move

Dry (EM617

model only)

5

OPERATING THE SWASH

EM617 Remote Control

7

User

Memory 1

User

Memory 2

Remote Control IR

Signal Transmitter

16

1. Stop

Stops all wash and dry functions

currently operating.

2. Rear Wash / Move

Touch once to initiate a rear wash. Touch

again to initiate nozzle oscillation (repetitive

forward and backward nozzle movement).

3. Front Wash / Move

Touch once to initiate a front wash. Touch

again to initiate nozzle oscillation (repetitive

forward and backward nozzle movement).

4. Strong Wash / Move

Touch once to initiate a strong wash. Touch

again to initiate nozzle oscillation (repetitive

forward and backward nozzle movement).

5. Dry (EM617 model only)

Touch once to initiate a two-minute Warm Air

Dryer cycle.

6. Nozzle Position

Touch the up and down arrows to adjust

the nozzle position forward and backward

during a wash cycle.

7. Water Temperature and Indicator

Touch and release Water Temp to adjust the

outgoing water temperature to one of four

settings (Low: 91.4°F, Medium: 96.8°F, High:

102.2°F, and O). Settings will be saved for

the next use.

8. Seat Temperature and Indicator

Touch and release Seat Temp to adjust the

seat temperature to one of four settings

(Low: 93.2°F, Medium: 100.4°F,

High: 107.6°F, and O). Settings will be

saved for the next use.

9. Pulse

Touching Pulse while a wash is

running enables the water to repeatedly

increase and decrease in pressure in a

pulsating pattern.

OPERATING THE SWASH

BL97 / EM617 Remote Control

10. Gentle Mode Button

Touch Gentle to initiate a two-minute

gentle wash cycle followed by a two-minute

dry cycle (EM617 model only). See page 17

for more information.

11. Water Pressure and Dry Temperature

(Dryer on EM617 model only)

Touch “+” and “–” to increase and decrease

the outgoing water pressure to one of ﬁve

settings. Touching these while the Warm

Air Dryer is operating will adjust the drying

temperature (EM617 model only). For Front

Wash, Rear Wash and Dry, settings will be

saved for next use. For Strong Wash, the

highest pressure settings will default for

all uses.

12. Nozzle Cleaning

Touch Nozzle Cleaning to initiate Nozzle

Cleaning when not sitting on the seat, or

while seat sensor is deactivated. For more

nozzle maintenance see page 22.

13. Eco Mode and Indicator

Touch and release Eco Mode to select

between two energy-saving options

(Standard, High-Eciency). See page 18 for

more information.

14. User Memory 1

User Memory 1 contains the programming

for all of the custom settings to User 1's

wash cycles. See page 19 for more details.

15. User Memory 2

User Memory 2 contains the programming

for all of the custom settings to User 2's

wash cycles. See page 19 for more details.

16. Remote Control IR Signal Sensor

Transmits the signal from remote control to

the seat when a button is touched.

17

OPERATING THE SWASH

BL97 / EM617 Auxiliary Control Panel

Basic functions such as Rear and Front Wash can be used without

the remote by utilizing the auxiliary buttons shown below.

AUXILIARY CONTROL PANEL

1. Front Wash Button

Initiates the front wash function utilizing the settings last used.

Press a second time to initiate the Move function. Press again to

stop the Move function.

2. Rear Wash Button

Initiates the rear wash function utilizing the settings last used.

Press a second time to initiate the Move function. Press again to

stop the Move function.

3. Stop Button

Stops all wash functions currently operating.

12 3

18

Prepare for Wash

Sit on the seat to ensure skin-to-seat contact on

the Seat Sensor.

Warm Water Wash

When ready to wash, touch Rear Wash, Front

Wash, or Strong Wash on the remote one time

to initiate a wash. The nozzle will self-clean,

extend into the toilet bowl, spray for two

minutes, turn o automatically, retract, and

self-clean once again.

1. Touching Rear Wash, Front Wash, or Strong

Wash a second time while the wash is

running will cause the nozzle to oscillate

forward and backward, providing a wider

range of wash spray. Touch again to cancel

the Move function.

2. While washing, users can adjust the water

temperature, pressure, and nozzle position

settings, as well as initiate the Pulse feature

by following the notes on page 15.

3. If you would like to stop the wash before

the two-minute cycle ends, touch Stop to

discontinue water ﬂow.

4. After extended use the water may decrease in

temperature if a Low, Medium, or High water

temperature setting is selected. To regain

warmer water, stop all wash functions for three

minutes to allow the bidet to reheat the water.

Warm Air Dryer Function (EM617 model only)

Touch Dry to activate the Warm Air Dryer.

NOTE: The wash functions will not work

unless the sensor in the seat detects someone

sitting down (with the built-in skin conductivity

sensor). To override the Seat Sensor, please

see the instructions on page 18.

OPERATING THE SWASH

Using the BL97 / EM617

The dryer will run for two minutes and turn

o automatically.

1. While the air dryer is operating, users

can adjust the dryer temperature to a

comfortable level using Dry Temp “+” and

“–” . The dry temperature will be reﬂected

on the ﬁve indicator LEDs.

2. If you would like to stop the dryer before the

two minutes has elapsed, touch Stop.

Gentle Mode

All settings within Gentle Mode are 40%

softer than standard wash modes.

Once activated, gentle mode will begin a

two-minute wash including:

• Full nozzle extension

• Water Pressure set to low

• Front Wash for one minute, Nozzle

Oscillation for 30 seconds, then Pulse

for 30 seconds

After the wash cycle is over, Gentle Mode will

initiate a two minute Warm Air Dry cycle on

Level Two (EM617 model only).

NOTE: While the Gentle Mode cycle is running,

the Water Pressure setting is adjustable. Dryer

settings are also adjustable during the Gentle

Mode (EM617 model only).

La page charge ...

brondell EM617-EW Le manuel du propriétaire

brondell EM617-EW Le manuel du propriétaire

dans d''autres langues

Documents connexes