brondell Swash Thinline T22 Le manuel du propriétaire

Owner's Manual

Swash T22

Luxury Bidet Toilet Seat

Models T22EW / T22RW

2

SAFETY INFORMATION

3 Important Safeguards

PRODUCT INFORMATION

7 Product Features

8 Product Dimensions

9 Product Parts

PRODUCT INSTALLATION

10 Installation Parts

11 Before Installation

12 Swash Installation

15 External Bidet Filter Installation

PRODUCT OPERATION

16 Control Panel

18 Using the Swash: Getting Started

19 Special Mode Operations

20 Special Mode Operation:

Memory Functions

21 Expert Mode Operations Level 1

23 Expert Mode Operations Level 2

MAINTENANCE

25 Seat Cleaning, Removal,

and Nozzle Cleaning

26 Mesh Filter and Carbon

Deodorizer Cartridge

27 Product Storage

TECHNICAL INFORMATION

28 Troubleshooting

31 Product Speciﬁcations

32 Warranty

33 Contact Information

TRANSLATIONS

34 Spanish

66 French

This manual contains important safety

information. Before operating the bidet,

please read this manual thoroughly,

and retain it for future reference.

T22 OWNER’S MANUAL

Contents

3

SAFETY INFORMATION

Important Safeguards

READ ALL INSTRUCTIONS BEFORE USING

BE CAREFUL TO KEEP THIS SAFETY INFORMATION. PLEASE READ THIS INFORMATION

TO PREVENT PROPERTY LOSS AND ENSURE SAFETY.

Do not use a damaged power plug or plug into

a loose electric outlet.

Do not move the product by pulling the power

cord.

Do not handle the product or power plug with

wet hands.

Do not forcefully bend the power cord or place

heavy objects on it to prevent it from being

damaged or deformed.

Do not connect and pull out the power plug or

cord repeatedly.

Unplug the product before cleaning, repairing,

inspecting, or replacing parts.

Remove any dust or water from the power plug

prior to plugging in.

Do not plug the product into an electrical

outlet or power strip that is being used by too

many other products. Use an electrical outlet

adequate for the wattage of the product rated

for a minimum of 15 amps.

If the power cord is damaged, do not attempt

to repair, modify, or replace the cord yourself.

Contact the Brondell Service Center toll free

at 888-542-3355 or email us through our

website.

If the product produces a strange noise,

a burning smell, or emits smoke, unplug it

immediately from the electrical outlet and

contact Brondell. Failure to do so may result in

electric shock or ﬁre.

Do not insert any wires or sharp objects into

any product gaps. This may result in electric

shock, ﬁre, or product damage.

Do not place an electronic or gas heater

near the product or dispose of any burning

materials such as a lit cigarette in the toilet.

This may result in ﬁre or product deformation.

Do not place any containers ﬁlled with water

or other liquids, food, metallic objects, or any

ﬂammable material on top of the product. If

foreign material enters the product, this may

result in electric shock or ﬁre.

DANGER

Failure to observe the following warnings may result in electric shock, ﬁre,

personal injury, property damage, or product damage.

4

SAFETY INFORMATION

Important Safeguards

READ ALL INSTRUCTIONS BEFORE USING

BE CAREFUL TO KEEP THIS SAFETY INFORMATION. PLEASE READ THIS INFORMATION

TO PREVENT PROPERTY LOSS AND ENSURE SAFETY.

Do not plug in, operate, or store the unit in

locations where ﬂammable or combustible

materials are used or kept.

Do not use industrial water, or gray water for

the supply, as this may cause skin damage or

disease.

Turn o the main water supply valve when

cleaning.

For children and seniors who may have

diculties with adjusting temperatures or those

with sensitive skin or impaired heat sensitivity,

set the temperature of the wash spray and seat

to “low” or “o” to prevent burning.

Close supervision is necessary when this

product is used by children, seniors, or

persons requiring general assistance.

Do not press the buttons using excessive

force.

Do not stand on top of or place any heavy

objects onto the seat cover.

Use this product for its intended use only,

as described in this manual. Do not use any

attachments that are not recommended by

Brondell.

Do not use the product in locations exposed

to excessive moisture and do not splash water

onto the product.

While cleaning the bathroom, pull the power

plug out of the electrical outlet and exercise

caution to ensure that water or cleaning

supplies do not splash onto the bidet. Failure

to do so may result in electric shock or ﬁre.

If foreign material enters the product, pull the

power plug out of the electrical outlet, turn

o the main water valve, and call the Brondell

Service Center.

Do not disassemble, repair, or modify the

product yourself.

Do not use the product while wet from bathing

or showering.

Do not place or store the product where it can

fall or be pulled into a tub or sink.

Do not place in or drop the product into water

or any other liquid.

Do not reach for the product if it has fallen into

water. Unplug the product immediately and

call the Brondell Service Center.

Do not use the product if it is not working

properly. Please unplug the product

immediately, close the main water supply

valve, and call the Brondell Service Center at

888-542-3355. Failure to do so may result in

electric shock, ﬁre, or ﬂooding.

DANGER

Failure to observe the following warnings may result in electric shock, ﬁre,

personal injury, property damage, or product damage.

WARNING

Failure to observe the following warnings may result in electric shock, ﬁre,

personal injury, property damage, or product damage.

5

SAFETY INFORMATION

Important Safeguards

READ ALL INSTRUCTIONS BEFORE USING

BE CAREFUL TO KEEP THIS SAFETY INFORMATION. PLEASE READ THIS INFORMATION

TO PREVENT PROPERTY LOSS AND ENSURE SAFETY.

Do not connect the main water supply to the

hot water pipe or supply (only connect to the

cold water supply).

After the installation, make sure to check all

water supply connections for leaks. Rubber

washers should be in place for the water

connection hoses & T-valve.

Do not open/close the seat or seat cover with

excessive force.

Exercise caution that urine does not come into

contact with the product - failure to do so may

result in bad odors or malfunction.

If the product will not be used for a long period

of time, unplug the power cord, close the main

water supply valve, and drain any water in the

water tank.

Do not pull out the bidet hose using excessive

force.

Do not use thinner, benzene, acidic chemicals,

chloride, or hydrochloric acid detergent on or

near the product. This may result in corrosion

to the metal parts or discoloration or scratches

to the bidet body.

This appliance is not intended for use by

persons (including children and seniors)

with reduced physical, sensory, or mental

capabilities, or lack of experience and

knowledge, unless they have been given

supervision or instruction concerning the use

of the appliance by a person responsible for

their safety.

Children should be supervised to ensure that

they do not play with the appliance.

Never operate this product if it has a damaged

cord or plug, if it is not working properly, if it

has been dropped or damaged, or dropped

into water. Contact the Brondell Service

Center for examination and repair.

Keep the cord away from heated surfaces and

heating vents.

Never block the air openings of the product

or place it on a soft surface, such as a bed

or couch, where the air openings may be

blocked. Keep the air openings free of lint,

hair, etc.

Never drop or insert any object into any

opening or hose.

Do not use the product outdoors or operate

where aerosol (spray) products are being

used, or a room where the product could be

exposed to oxygen.

Connect the product to a properly grounded

outlet only. Refer to the Grounding Instructions

in the next pages of the manual.

WARNING

Failure to observe the following warnings may result in electric shock, ﬁre,

personal injury, property damage, or product damage.

CAUTION

Failure to observe the following warnings may result in electric shock, ﬁre,

personal injury, property damage, or product damage.

6

DANGER

Improper use of the grounding plug can result in a risk of electric shock.

If repair or replacement of the cord or plug is necessary, do not connect the

grounding wire to either ﬂat blade terminal. The wire with green insulation

(either with or without a yellow stripe) is the grounding wire.

Check with a qualiﬁed electrician if the grounding instructions are not completely

understood, or if there is doubt if the product is properly grounded.

ATTENTION

For those with certain medical or mobility issues in the bathroom, we recommend

our Swash 1400 or Swash 1000 bidet seats, as their mounting systems are engineered

for the most secure transitions from wheelchairs or walkers.

GROUNDING AND GFCI OUTLET

INSTRUCTIONS

This product should only be used with

a grounded GFCI (Ground Fault Circuit

Interrupter) outlet and a grounded three-

prong electrical cord as shown to the right.

In the event of an electrical short circuit, using

a grounded GFCI outlet reduces the risk of

electric shock.

This product is equipped with a grounded

cord and is for use on a nominal 120V circuit

only (minimum 15 amps) and must be plugged

into an outlet that is properly grounded with

a GFCI breaker as shown. Replace or repair a

damaged cord immediately. 12

3

1. Grounding Pin

2. Test Button

3. Reset Button

SAFETY INFORMATION

Important Safeguards

READ ALL INSTRUCTIONS BEFORE USING

BE CAREFUL TO KEEP THIS SAFETY INFORMATION. PLEASE READ THIS INFORMATION

TO PREVENT PROPERTY LOSS AND ENSURE SAFETY.

7

Stainless steel nozzle

Stainless steel resists soiling and

contamination for enhanced hygiene

Rear and front warm water wash

Adjustable temperature, position, pressure,

and oscillation settings

Strong wash

Concentrated stream with adjustable pressure,

position, temperature, and oscillation settings

Nozzle positioning

Adjustable, 5-position nozzle ensures a

comfortable and complete wash

Ceramic water heating system

Instant ceramic heating system provides an

endless warm water stream for washes

Adjustable water temperature and pressure

Front, rear, and strong wash modes have 4

available water temperature settings and 5

water pressure settings

Warm air dryer

Adjustable, 5-level temperature setting for a

hands-free drying experience and toilet paper

reduction/elimination

Nozzle oscillation

Move function provides a massaging,

oscillating cleanse during the wash cycle,

ensuring a thorough and comfortable wash

Gentle wash

Activates a preset wash cycle at the softest

setting for a gentle clean, followed by a

drying cycle

Deodorizer

Activated charcoal deodorizing ﬁlter

eliminates odors at the source

Ergonomic heated seat

Provides 4 temperature settings for comfort

(o/low/medium/high)

Multicolored, illuminating nightlight

Select a preferred nightlight color to help

ensure safer evening bathroom visits

Gentle-close seat and lid

Gentle-close seat and lid eliminates slamming

and pinched ﬁngers

Sittable lid

Sturdy, sittable lid can support up to 264

pounds

Quick-release seat

Quick-release button for easy removal and

cleaning of the seat and toilet

Nozzle cleaning

Activate for automatic or manual nozzle

cleaning

Programmable user memory

Set water pressure, oscillation, water

temperature, nozzle positioning, and seat

temperature for two users

Eco mode

Automatically lowers the seat temperature for

energy saving when activated

Expert mode custom settings

Personalize and change the running time of

wash and dry cycles

PRODUCT INFORMATION

Product Features

8

PRODUCT INFORMATION

Product Dimensions

Required Distance Between Mounting Holes

Elongated Top View

Round Top View

20.7” / 52.6 cm

11.8” / 30 cm

7.9” / 20.1 cm

2.1” / 5.3 cm

15” / 38.1 cm 17.6” / 44.7 cm

5.3–7.7” / 13.50–19.6 cm

7.9” / 20.1 cm

2.1” / 5.3 cm

19.6” / 49.8 cm

11” / 28.0 cm

15” / 38.1 cm 17.6” / 44.7 cm

9

PRODUCT INFORMATION

Product Parts

1. Lid

2. Control panel

3. Nozzle assembly

4. Seat sensor area

5. Quick-release button

6. Deodorizer cover & outlet

7. Deodorizer inlet

8. Mounting plate

9. Water inlet with mesh ﬁlter

10. Nightlight

11. Power cord

1

2

3

6

5

4

11

7

8

9

10

PRODUCT INSTALLATION

Installation Parts

1. Metal mounting bolt (2)

2. Rubber anchor (2)

3. T-valve connector with rubber washer

4. Deodorizer cover

5. Carbon deodorizer cartridge

6. Bidet hose

7. Adjustable brackets (2)

8. Mounting plate

6

1 2

7

5

3

8

4

11

PRODUCT INSTALLATION

Before Installation

Watch our installation video

Installation for all Swash products can be

found online at brondell.com

Check bolt spread

This bidet seat can only be installed on toilets

with a bolt hole spread of 5.3–7.7”.

(see Product Dimensions on page 8 for more

information).

Check for a concealed toilet ﬁll valve

Many modern toilets have sleek designs

intended to cover and camouﬂage plumbing

connections, which make a standard Swash

installation dicult or impossible. For this, we

recommend using our Alternate Swash Bidet

Seat T-valve, found on brondell.com.

Check water supply line

Check the line that connects the toilet tank

to the water shut o valve. If it is a rigid pipe,

you may need to purchase a ﬂexible hose

to replace it before installing the Swash.

The length of the hose and the size of the

connectors will vary.

Residual moisture is normal

Every product is tested with pure water during

production to ensure the highest quality

and performance. It is normal to ﬁnd a small

amount of residual moisture on the product.

Tools

A Phillips head or standard screwdriver may be

needed to remove the existing toilet seat and

a standard wrench may be needed for tight

water supply connections. Teﬂon tape can be

helpful in creating a water-tight seal between

plumbing connections.

CAUTION

Do not plug the product in while the unit is upside down.

This may cause damage to the internal components.

12

Please read these instructions carefully before

installing the Swash. Failure to do so could

result in ﬂooding, leaking, or damage to the

product.

1. Existing toilet seat removal

a. Lift hinge covers and use a screwdriver

to remove the mounting bolts.

b. Remove the toilet seat; keep for future

use.

2. Turn o water supply valve and ﬂush toilet

a. Turn water valve o to stop the ﬂow of

water.

b. Flush toilet and hold down handle to

completely empty tank.

c. Disconnect water supply hose from toilet

tank; do not disconnect from the water

supply valve.

3. Connect the top of the T-valve to the

incoming water connection on the bottom

of your toilet tank

4. Connect the water supply line coming from

the wall to the bottom of the T-valve

PRODUCT INSTALLATION

Swash Installation

NOTE: Steps may vary by type of seat

and toilet

NOTES:

You may wish to place a container under

the tank to catch excess water.

Do not continue without completing the

above steps.

Failure to do so could result in ﬂooding,

leaking, or damage to the Swash.

Steps 3,4

Step 2c

Continued following page

NOTES:

The T-valve connects to the ﬁll valve

directly under your toilet tank—it does

not connect at the wall.

Check to ensure the rubber washer sits

ﬂat inside of the T-valve.

Only connect to the cold toilet water

supply line.

If your water supply line is rigid you may

need to replace the water supply line

before continuing.

5. Installing mounting plate

a. Wet the rubber anchors with water,

squeeze the sides of the anchors, and

ﬁrmly press them all the way down into

the mounting holes on top of the toilet.

b. Place the mounting plate over the rubber

anchors on the toilet.

c. Place the adjustable brackets ﬂat side

down on the mounting plate over the

rubber anchors.

d. Insert the metal mounting bolts through

the adjustable brackets and rubber

anchors; use a Phillips screwdriver to

screw in the mounting bolts and tighten.

6. Insert the deodorizer cartridge into the back

of the bidet body and attach the deodorizer

cover until it snaps into place.

7. Connect the bidet hose to the seat

Connect the bidet hose to the water inlet

and hand-tighten to secure; take care not

to twist the bidet hose, excessively bend

it, or strip the plastic screw threads when

screwing the hose onto the bidet seat.

8. Attach the bidet seat to the mounting plate

a. Set the bidet seat ﬂat on the toilet bowl

in front of the mounting plate. Slide seat

forward onto plate until it clicks into place

and is secure.

b. If the seat does not align with the front

edge of the toilet bowl, remove the seat

by pressing the quick-release button

located on the right side of the seat and

slide it o the mounting plate.

13

TIP: Wetting the rubber anchors will

allow for easier installation. The top of

the anchors should be ﬂat to the surface.

Steps 5b–5d

Step 6

Step 5a

Continued following page

Step 7

c. Loosen the bolts and slide the mounting

plate back or forth to readjust the

placement; reinstall the seat and check

the alignment to the edge of the toilet

bowl (you may need to remove, readjust,

and reinstall multiple times).

d. When the seat is lined up properly, tighten

the bolts and reinstall the bidet seat.

9. Connect the open end of the bidet hose to

the T-valve

10. Turn on the water supply

a. Open the main water supply valve slowly

and check for leaks.

b. Wait 5 minutes, check again and, if there

are no leaks, continue.

11. Plug the power cord into an electrical

outlet; nozzle will extend and retract.

12. Follow instructions on page 18 for using the

bidet seat

14

PRODUCT INSTALLATION

Swash Installation (Cont’d)

NOTES:

Make sure to only use a grounded GFCI

(ground fault circuit interrupter) electrical

outlet, as in the case of a short circuit, a

grounded GFCI outlet may help prevent

electric shock or injury.

If it is necessary to use an extension

cord, only use those rated for a minimum

of 15 amps with a 3-wire extension cord

and a 3-blade grounding plug.

Step 8

Step 9

15

1. Turn o water supply valve and ﬂush toilet

a. Turn water valve o to stop the ﬂow of

water.

b. Flush toilet and hold down handle to

completely empty tank.

2. Disconnect the bidet hose from the T-valve

3. Connect the female end of the Swash ﬁlter

to the open T-valve connection

4. Connect the bidet hose to the male end of

the Swash ﬁlter

5. Turn the toilet water supply valve back on

PRODUCT INSTALLATION

External Bidet Filter Installation (optional, not included)

NOTE: Customers with hard water, well

water, and softened water can extend

the life of their bidet seat by purchasing

and installing an external inline water

ﬁlter to be used with the bidet seat. The

bidet ﬁlter should be changed every 6

months and can be purchased online at

brondell.com.

Step 2

FLOW

Step 4

FLOW

Step 3

16

PRODUCT OPERATION

Control Panel

1115

14

762 3 85

13

9

12

41

10

17

1. Stop Button

Stops all wash and dry functions currently

operating.

2. Rear Wash / Move Button

Press once to initiate a 2-minute rear wash.

Press again to initiate nozzle oscillation

(repetitive forward and backward nozzle

movement).

3. Front Wash / Move Button

Press once to initiate a 2-minute front wash.

Press again to initiate nozzle oscillation

(repetitive forward and backward nozzle

movement).

4. Strong Wash / Move Button

Press once to initiate a 2-minute strong

wash. Press again to initiate nozzle

oscillation (repetitive forward and backward

nozzle movement).

5. Dry Button

Press once to initiate a 2-minute warm air

dryer cycle.

6. Nozzle Position

Press the left or right arrow to adjust the

nozzle position forward and backward

during a wash cycle. The 5 LED indicator

lights will indicate the dierent positions

selected.

7. Nightlight Button

Press to turn the nightlight ON/OFF and to

change the color of the nightlight.

8. Seat Temperature Button and Indicator

Press to adjust the seat temperature to 1 of 4

settings (green/low: 93.2°F, yellow/medium:

98.6°F, red/high: 104°F, and OFF). Settings

will be saved for the next use.

9. Nozzle Cleaning Button

Press to initiate nozzle cleaning when not

sitting on the seat, or when the seat sensor

is deactivated. For more nozzle maintenance

instructions, see page 25.

10. Deodorizer Button

Deodorizer is defaulted to automatically

turn on when seated (indicator light is ON).

Press button to turn the auto deodorizer o

(indicator light is OFF). See page 19 for more

instructions.

11. Water Temperature Button and Indicator

Press to adjust the water temperature to

1 of 4 settings (green/low: 93.2°F, yellow/

medium: 98.6°F, red/high: 104°F, and OFF).

Settings will be saved for the next use.

12. Gentle Wash Button

Press to initiate a gentle wash cycle followed

by a dry cycle. See page 18 for more

instructions.

13. Water Pressure and Dry Temperature

Press the button + or – to adjust the water

pressure during a wash cycle. Press

the same button + or – to adjust the dry

temperature during a dry cycle. The 5 LED

indicator lights will indicate the dierent

positions selected. Settings will be saved for

the next use.

14. Memory User 1 and User 2 Buttons

Press User 1 or User 2 to initiate preferred

settings for a wash. User can set nozzle

position, water pressure, oscillation,

water temperature, and seat temperature

settings to memory. See page 20 for more

instructions.

15. Five LED Indicator Lights

Indicator lights for Level 1 to Level 5 from

right to left indicate nozzle position, water

pressure, and dryer temperature level

settings when those buttons are pressed.

18

PRODUCT OPERATION

Using the Swash: Getting Started

Prepare for Wash

Sit on the seat to ensure skin-to-seat contact

on the seat sensor.

Warm Water Wash

When ready to wash, press the Rear Wash,

Front Wash, or Strong Wash button on the

control panel once to initiate a wash. The

nozzle will perform a self-cleaning rinse,

extend into the toilet bowl, spray for 2 minutes,

turn o automatically, retract, and self-clean

once again.

1. To activate the move function during a

wash, press the Rear Wash, Front Wash,

or Strong Wash button a second time. This

will initiate the nozzle to oscillate forward

and backward, providing a wider wash

spray range. Press again to stop the move

function.

2. While washing, users can adjust the water

temperature, pressure, and nozzle position

settings. See page 17 for details.

3. To stop the wash before the 2-minute cycle

ends, press the Stop button to discontinue

water ﬂow.

Warm Air Dryer Function

Press the Dry button to activate the warm air

dryer. The dryer will run for 2 minutes and turn

o automatically.

1. While the air dryer is operating, users

can adjust the dryer temperature to a

comfortable level using the Dry Temp +

and – button on the control panel. The dry

temperature will be reﬂected on the 5 LED

indicator lights.

2. To stop the dryer before the 2-minute cycle

ends, press the Stop button.

Gentle Wash

Auto settings within the gentle wash mode are

40% softer than standard wash modes. Gentle

wash will begin a wash that includes:

• full nozzle extension

• water pressure set to level 2

• front wash and oscillation for 1.5 minutes

• warm air dry cycle for 2-minutes set

on level 2

NOTE: The seat has a built-in skin

conductivity sensor. The wash functions

will not work unless the sensor detects

someone is seated. To override the seat

sensor, see instructions on page 22.

NOTE: During a gentle wash cycle, water

pressure and dryer settings may still be

adjusted.

19

Deodorizer

1. The deodorizer is defaulted to automatically

turn on when seated. When the auto

deodorizer is on, the deodorize indicator

light is ON. After leaving the seat, it will

automatically turn OFF after 1 minute.

2. To manually turn OFF the auto deodorizer,

press the Deodorize button and the

indicator light will turn OFF. The deodorizer

will remain o until it is turned back on

again by pressing the Deodorize button.

Nightlight

1. To change the nightlight color, press the

Nightlight button repeatedly to cycle

through and select your preferred color.

2. To turn OFF the nightlight, press and hold

the Nightlight button for 3 seconds. It will

beep twice to indicate it is o.

3. To turn ON the nightlight, press the

Nightlight button for 1 second. It will beep

once to indicate it is on.

Power ON/OFF

1. To power OFF and shut down the bidet

seat, press and hold the Deodorize button

for 3 seconds. The unit will make a tone and

power OFF, shutting down the nightlight,

seat heater, and water heater.

2. To power ON, press and hold the Deodorize

button. The unit will make a tone and power

ON.

Factory Default Reset

1. Factory reset can only be performed when

the seat is not occupied.

2. To reset the bidet seat back to its factory

default program settings, press the Stop

button 4 times within 2 seconds to clear all

current programming.

3. A tone will be heard to conﬁrm that the

bidet seat has been reset.

PRODUCT OPERATION

Special Mode Operations

NOTE: Factory default reset only resets

programming.

20

PRODUCT OPERATION

Special Mode Operation: Memory Functions

User Memory Settings

The Swash User 1 and User 2 memory

functions allow you to program your preferred

wash settings for rear, front, or strong wash

cycles for two users. These settings include

nozzle positioning, water pressure, water

temperature, seat temperature, and move

function. Follow the steps below to program

and use the memory function.

Programming User 1 Memory Function

1. Sit on the seat and select your wash cycle

(rear, front, strong). Adjust the nozzle

position, water pressure, water temperature,

seat temperature, and/or activate move

function, to your preference.

2. Press the Stop button.

3. Press User 1 for 2 seconds. A beep will

occur, and the yellow Deodorize LED

light on the remote will blink to conﬁrm

programming is complete.

4. Repeat instructions for the next wash cycle

you want to program.

Programming User 2 Memory Function

1. Sit on the seat and select your wash cycle

(rear, front, strong). Adjust the nozzle

position, water pressure, water temperature,

seat temperature, and/or activate move

function, to your preference.

2. Press the Stop button.

3. Press User 2 for 2 seconds. A beep will

occur, and the yellow Deodorize LED button

on the remote will blink to conﬁrm the

programming is complete.

4. Repeat instructions for the next wash cycle

you want to program.

Using User 1 and User 2 Memory Function

1. Sit on the seat and select User 1 or User 2.

The deodorize LED light will ﬂash alerting

you that user memory is activated.

2. Press Rear, Front, or Strong Wash

button depending on which cycle was

programmed.

3. The preset nozzle positioning, water

pressure, water temperature, seat

temperature, and move function (if selected)

will be activated.

4. To stop user preset wash before the cycle

ends, press Stop.

5. To exit user preset, press the same user

button again and the deodorize LED light

will turn o. This will revert to the previous

settings.

NOTE: After leaving the seat without

manually exiting, the seat will

automatically revert to the previous

settings.

La page est en cours de chargement...

brondell Swash Thinline T22 Le manuel du propriétaire

brondell Swash Thinline T22 Le manuel du propriétaire

dans d''autres langues

Documents connexes