brondell Swash Eco Thinline T66 Le manuel du propriétaire

Owner’s Manual

Swash Eco Thinline T66

Electronic Luxury Bidet Toilet Seat

Model: T66EW

2

This manual contains important safety

information. Before operating the bidet,

please read this manual thoroughly,

and retain it for future reference.

T66 OWNER’S MANUAL

Contents

SAFETY INFORMATION

03 Important Safeguards

PRODUCT INFORMATION

07

08

09

Product Features

Product Dimensions

Product Parts

PRODUCT INSTALLATION

10

11

12

15

Product Parts

Before Installation

Swash Installation

External Bidet Filter Installation

PRODUCT OPERATION

16

18

19

20

22

24

Remote Control

Auxiliary Control Panel

Using the Swash: Getting Started

Special Mode Operations

Special Mode Operation:

Memory Functions

Expert Mode Operations Level 1

Expert Mode Operations Level 2

TECHNICAL INFORMATION

29

32

33

34

35

Troubleshooting

Product Speciications

Regulatory and Safety Notices

Warranty

Contact Information

MAINTENANCE

26

27

28

Seat Cleaning, Removal,

and Nozzle Cleaning

Mesh Filter and Carbon

Deodorizer Cartridge

Product Storage

TRANSLATIONS

36

70

Spanish

French

3

SAFETY INFORMATION

Important Safeguards

READ ALL INSTRUCTIONS BEFORE USING

BE CAREFUL TO KEEP THIS SAFETY INFORMATION. PLEASE READ THIS INFORMATION

TO PREVENT PROPERTY LOSS AND ENSURE SAFETY.

Do not use a damaged power plug or plug

into a loose electric outlet.

Do not move the product by pulling the

power cord.

Do not handle the product or power plug

with wet hands.

Do not forcefully bend the power cord or

place heavy objects on it to prevent it from

being damaged or deformed.

Do not connect and pull out the power plug

or cord repeatedly.

Unplug the product before cleaning,

repairing, inspecting, or replacing parts.

Remove any dust or water from the power

plug prior to plugging in.

Do not plug the product into an electrical

outlet or power strip that is being used by

too many other products. Use an electrical

outlet adequate for the wattage of the

product rated for a minimum of 15 amps.

If the power cord is damaged, do not

attempt to repair, modify, or replace the

cord yourself. Contact the Brondell Service

Center toll free at 888-542-3355 or email us

through our website.

If the product produces a strange noise,

a burning smell, or emits smoke, unplug

it immediately from the electrical outlet

and contact Brondell. Failure to do so may

result in electric shock or ire.

Do not insert any wires or sharp objects

into any product gaps. This may result in

electric shock, ire, or product damage.

Do not place an electronic or gas heater

near the product or dispose of any burning

materials such as a lit cigarette in the

toilet. This may result in ire or product

deformation.

Do not place any containers illed with

water or other liquids, food, metallic

objects, or any lammable material on top

of the product. If foreign material enters

the product, this may result in electric

shock or ire.

DANGER

Failure to observe the following warnings may result in electric shock, ire,

personal injury, property damage, or product damage.

4

SAFETY INFORMATION

Important Safeguards

READ ALL INSTRUCTIONS BEFORE USING

BE CAREFUL TO KEEP THIS SAFETY INFORMATION. PLEASE READ THIS INFORMATION

TO PREVENT PROPERTY LOSS AND ENSURE SAFETY.

Do not plug in, operate, or store the unit in locations

where lammable or combustible materials are used

or kept.

Do not use industrial water, or gray water for the

supply, as this may cause skin damage or disease.

Turn o the main water supply valve when cleaning.

For children and seniors who may have diiculties

with adjusting temperatures or those with

sensitive skin or impaired heat sensitivity, set the

temperature of the wash spray and seat to “low” or

“o” to prevent burning.

Close supervision is necessary when this product

is used by children, seniors, or persons requiring

general assistance.

Do not press the buttons using excessive force.

Do not stand on top of or place any heavy objects

onto the seat cover.

Use this product for its intended use only,

as described in this manual. Do not use any

attachments that are not recommended by

Brondell.

Do not use the product in locations exposed to

excessive moisture and do not splash water onto

the product.

While cleaning the bathroom, pull the power plug

out of the electrical outlet and exercise caution

to ensure that water or cleaning supplies do not

splash onto the bidet. Failure to do so may result

in electric shock or ire.

If foreign material enters the product, pull the

power plug out of the electrical outlet, turn

o the main water valve, and call the Brondell

Service Center.

Do not disassemble, repair, or modify the product

yourself.

Do not use the product while wet from bathing or

showering.

Do not place or store the product where it can fall

or be pulled into a tub or sink.

Do not place in or drop the product into water or

any other liquid.

Do not reach for the product if it has fallen into

water. Unplug the product immediately and call

the Brondell Service Center.

Do not use the product if it is not working

properly. Please unplug the product immediately,

close the main water supply valve, and call the

Brondell Service Center at 8885423355. Failure

to do so may result in electric shock, ire, or

looding.

DANGER

Failure to observe the following warnings may result in electric shock, ire,

personal injury, property damage, or product damage.

WARNING

Failure to observe the following warnings may result in electric shock, ire,

personal injury, property damage, or product damage.

5

SAFETY INFORMATION

Important Safeguards

READ ALL INSTRUCTIONS BEFORE USING

BE CAREFUL TO KEEP THIS SAFETY INFORMATION. PLEASE READ THIS INFORMATION

TO PREVENT PROPERTY LOSS AND ENSURE SAFETY.

Do not connect the main water supply to the hot

water pipe or supply (only connect to the cold

water supply).

After the installation, make sure to check all water

supply connections for leaks. Rubber washers

should be in place for the water connection

hoses & T-Valve.

Do not open/close the seat or seat cover with

excessive force.

Exercise caution that urine does not come into

contact with the product - failure to do so may

result in bad odors or malfunction.

If the product will not be used for a long period

of time, unplug the power cord, close the main

water supply valve, and drain any water in the

water tank.

Do not pull out the bidet hose using excessive

force.

Do not use thinner, benzene, acidic chemicals,

chloride, or hydrochloric acid detergent on or

near the product. This may result in corrosion to

the metal parts or discoloration or scratches to

the bidet body.

This appliance is not intended for use by persons

(including children and seniors) with reduced

physical, sensory, or mental capabilities, or lack

of experience and knowledge, unless they have

been given supervision or instruction concerning

the use of the appliance by a person responsible

for their safety.

Children should be supervised to ensure that they

do not play with the appliance.

Never operate this product if it has a damaged

cord or plug, if it is not working properly, if it

has been dropped or damaged, or dropped into

water. Contact the Brondell Service Center for

examination and repair.

Keep the cord away from heated surfaces and

heating vents.

Never block the air openings of the product or

place it on a soft surface, such as a bed or couch,

where the air openings may be blocked. Keep the

air openings free of lint, hair, etc.

Never drop or insert any object into any opening

or hose.

Do not use the product outdoors or operate

where aerosol (spray) products are being used,

or a room where the product could be exposed

to oxygen.

Connect the product to a properly grounded

outlet only. Refer to the Grounding Instructions in

the next pages of the manual.

WARNING

Failure to observe the following warnings may result in electric shock, ire,

personal injury, property damage, or product damage.

CAUTION

Failure to observe the following warnings may result in electric shock, ire,

personal injury, property damage, or product damage.

6

DANGER

Improper use of the grounding plug can result in a risk of electric shock.

If repair or replacement of the cord or plug is necessary, do not connect the

grounding wire to either lat blade terminal. The wire with green insulation

(either with or without a yellow stripe) is the grounding wire.

Check with a qualiied electrician if the grounding instructions are not completely

understood, or if there is doubt if the product is properly grounded.

SAFETY INFORMATION

Important Safeguards

READ ALL INSTRUCTIONS BEFORE USING

BE CAREFUL TO KEEP THIS SAFETY INFORMATION. PLEASE READ THIS INFORMATION

TO PREVENT PROPERTY LOSS AND ENSURE SAFETY.

ATTENTION

For those with certain medical or mobility issues in the bathroom, we recommend

our Swash 1400 or Swash 1000 bidet seats, as their mounting systems are engineered

for the most secure transitions from wheelchairs or walkers.

GROUNDING AND GFCI OUTLET

INSTRUCTIONS

This product should only be used with

a grounded GFCI (Ground Fault Circuit

Interrupter) outlet and a grounded three-prong

electrical cord as shown to the right.

In the event of an electrical short circuit,

using a grounded GFCI outlet reduces the

risk of electric shock.

This product is equipped with a grounded

cord and is for use on a nominal 120V circuit

only (minimum 15 amps) and must be plugged

into an outlet that isproperly grounded with

a GFCI breaker as shown. Replace or repair

a damaged cord immediately. 12

3

1. Grounding Pin

2. Test Button

3. Reset Button

7

Eco-friendly design

10% recycled ABS plastic used in lid,

remote and dock

Self-cleaning, stainless steel nozzle

Nozzle retracts to stay clean between uses.

Self-cleaning feature gives nozzle a sanitary

rinse—on demand.

Strong wash

Concentrated stream with adjustable

pressure, position, temperature, and

oscillation settings.

Nozzle positioning

Adjustable, 5-position nozzle ensures a

comfortable and complete wash.

Ceramic water heating system

Instant ceramic heating system provides an

endless warm water stream for washes.

Adjustable water temperature and

pressure

Front, rear, and strong wash modes have 4

available water temperature settings and 5

water pressure settings.

Warm air dryer

Adjustable, 5-level temperature setting for

a hands-free drying experience and toilet

paper reduction/elimination.

Nozzle oscillation

Move function provides a massaging,

oscillating cleanse during the wash cycle,

ensuring a thorough and comfortable

wash.

Gentle wash

Activates a preset wash cycle at the softest

setting for a gentle clean, followed by a

drying cycle.

Replaceable carbon deodorizer

Activated charcoal deodorizing ilter

eliminates odors at the source.

Heated toilet seat

Provides 4 temperature settings for

comfort (o/low/medium/high).

Multicolored LED nightlight with

on/o switch

Select a preferred nightlight color to help

ensure safer evening bathroom visits.

Gentle-close seat and lid

Gentle-close seat and lid eliminates

slamming and pinched ingers.

Sittable lid

Sturdy, sittable lid can support up to 264

pounds.

Quick-release seat

Quick-release button for easy removal and

cleaning of the seat and toilet.

Wireless remote control

Intuitive remote and magnetic dock with

adhesive backing. Three AAA batteries

included.

Programmable user memory

Set water pressure, oscillation, water

temperature, nozzle positioning, and seat

temperature for two users.

Eco mode

Automatically lowers the seat temperature

for energy saving when activated.

Expert mode custom settings

Personalize and change the running time of

wash and dry cycles.

PRODUCT INFORMATION

Product Features

8

PRODUCT INFORMATION

Product Dimensions

Required Distance Between

Mounting Holes

Elongated Top View

20.7 in

11.8 in

7.9 in 15 in

5.3–7.7 in

9

PRODUCT INFORMATION

Product Parts

1. Lid

2. Auxiliary control panel

3. Nozzle assembly

4. Seat sensor area

5. Quick-release button

6. Deodorizer cover & outlet

7. Deodorizer inlet

8. Mounting plate

9. Water inlet with mesh ilter

10. Nightlight

11. Power cord

1

2

3

6

4

11

7

8

10

5

9

10

PRODUCT INSTALLATION

Installation Parts

1. Metal mounting bolt (2)

2. Rubber anchor (2)

3. T-Valve connector with rubber washer

4. Deodorizer cover

5. Carbon deodorizer cartridge

6. Bidet hose

7. Adjustable brackets (2)

8. Mounting plate

9. Remote control

10. Remote control wall mount

11. AAA batteries (3)

11

7

6

123

8

5

910

4

11

PRODUCT INSTALLATION

Before Installation

Watch our installation video

Installation for all Swash products can be

found online at brondell.com

Check bolt spread

This bidet seat can only be installed on

toilets with a bolt hole spread of 5.3–7.7 in.

(see Product Dimensions on page 8 for

more information).

Check for a concealed toilet ill valve

Many modern toilets have sleek designs

intended to cover and camoulage

plumbing connections, which make a

standard Swash installation diicult or

impossible. For this, we recommend using

our Alternate Swash Bidet Seat T-Valve,

found on brondell.com.

Check water supply line

Check the line that connects the toilet tank

to the water shut o valve. If it is a rigid

pipe, you may need to purchase a lexible

hose to replace it before installing the

Swash. The length of the hose and the size

of the connectors will vary.

Residual moisture is normal

Every product is tested with pure water

during production to ensure the highest

quality and performance. It is normal to

ind a small amount of residual moisture on

the product.

Tools

A Phillips head or standard screwdriver may

be needed to remove the existing toilet

seat and a standard wrench may be needed

for tight water supply connections. Telon

tape can be helpful in creating a water-tight

seal between plumbing connections.

CAUTION

Do not plug the product in while the unit is upside down.

This may cause damage to the internal components.

12

3. Connect the top of the TValve to the

incoming water connection on the

bottom of your toilet tank

4. Connect the water supply line coming

from the wall to the bottom of the TValve

Please read these instructions carefully before

installing the Swash. Failure to do so could

result in looding, leaking, or damage to the

product.

1. Existing toilet seat removal

a. Lift hinge covers and use a screwdriver

to remove the

mounting bolts.

b. remove toilet seat and keep for

future use.

2. Turn o water supply valve and lush

toilet

a. Turn water valve o to stop the low of

water.

b. Flush toilet and hold down handle to

completely empty tank.

c. Disconnect water supply line from toilet

tank

PRODUCT INSTALLATION

Swash Installation

NOTE: Steps may vary by type of seat

and toilet.

NOTE: Do not disconnect from the

water supply valve.

NOTE: You may wish to place a container under

the tank to catch excess water.

Do not continue without completing the above

steps. Failure to do so could result in looding,

leaking, or damage to the Swash.

Steps 3,4

Step 2c

Continued following page

NOTE:

The T-Valve connects to the ill valve

directly under your toilet tank—it does

not connect at the wall.

Check to ensure the rubber washer sits

lat inside of the T-Valve.

Only connect to the cold toilet water

supply line.

If your water supply line is rigid you

may need to replace the water supply

line before continuing.

13

6. Insert the deodorizer cartridge into the

back of the bidet body and attach the

deodorizer cover until it snaps into place.

5. Installing mounting plate

a. Wet the rubber anchors with water,

squeeze the sides of the anchors, and

irmly press them all the way down into

the mounting holes on top of the toilet.

b. Place the mounting plate over the

rubber anchors on the toilet.

c. Place the adjustable brackets lat side

down on the mounting plate over the

rubber anchors.

d. Insert the washers and metal mounting

bolts through the adjustable brackets

and rubber anchors; use a Phillips

screwdriver to screw in the mounting

bolts and tighten.

PRODUCT INSTALLATION

Swash Installation (Cont’d)

TIP: Wetting the rubber anchors will

allow for easier installation. The top of

the anchors should be lat to the surface.

Step 6

Step 5a

Continued following page

Steps 5b–5d

14

9. Connect the open end of the bidet

hose to the TValve

10. Turn on the water supply

a. Open the main water supply valve

slowly and check for leaks.

b. Wait 5 minutes, check again and, if

there are no leaks, continue.

11. Plug the power cord into an electrical

outlet; nozzle will extend and retract.

12. Pair the remote control

a. Insert 3 AAA batteries (included)

into the remote within 5 minutes of

plugging the seat into a GFCI outlet.

b. After inserting batteries, a blue light

on the remote will turn on.

c. Press any button within 5 seconds

before light turns o. A melody will

play to conirm remote pairing.

d. Repeat the process if the remote did

not pair.

13. Follow instructions on page 19

for using the bidet seat. Follow

instructions on page 19 for using the

bidet seat.

7. Connect the bidet hose to the seat

Connect the bidet hose to the water inlet

and hand-tighten to secure; take care not

to twist the bidet hose, excessively bend

it, or strip the plastic screw threads when

screwing the hose onto the bidet seat.

8. Attach the bidet seat to the mounting

plate

a. Set the bidet seat lat on the toilet

bowl in front of the mounting plate.

Slide seat forward onto plate until it

clicks into place and is secure.

b. If the seat does not align with the

front edge of the toilet bowl, remove

the seat by pressing the quick release

button, which is located on the right

side if you’re facing the seat. When

the seat releases, slide it o the

mounting plate.

c. Loosen the bolts and slide the

mounting plate back or forth to

readjust the placement; reinstall the

seat and check the alignment to the

edge of the toilet bowl (you may need

to remove, readjust, and reinstall

multiple times).

d. When the seat is lined up properly,

tighten the bolts and reinstall the

bidet seat.

PRODUCT INSTALLATION

Swash Installation (Cont’d)

NOTES: Make sure to only use a ground-

ed GFCI (ground fault circuit interrupter)

electrical outlet, as in the case of a short

circuit, a grounded GFCI outlet may help

prevent electric shock or injury.

If it is necessary to use an extension cord,

only use those rated for a minimum of 15

amps with a 3-wire extension cord and a

3-blade grounding plug.

Step 7

Step 8

Step 9

15

1. Turn o water supply valve and lush

toilet

a. Turn water valve o to stop the low

of water.

b. Flush toilet and hold down handle to

completely empty tank.

2. Disconnect the bidet hose from the

TValve

3. Connect the female end of the Swash

ilter to the open TValve connection

4. Connect the bidet hose to the male

end of the Swash ilter

5. Turn the toilet water supply valve

back on

PRODUCT INSTALLATION

External Bidet Filter Installation (optional, not included)

NOTE: Customers with hard water,

well water, and softened water can

extend the life of their bidet seat by

purchasing and installing an external

inline water ilter to be used with the

bidet seat. The bidet ilter should be

changed every 6 months and can be

purchased online at brondell.com.

Step 2

FLOW

Step 4

FLOW

Step 3

16

9

10

12

13

4

5

8

11

14

15

7

6

2

1

3

PRODUCT OPERATION

Remote Control

1. Battery installation and remote pairing

a. Insert 3 AAA batteries (included)

into the remote within 5 minutes of

plugging the seat into a GFCI outlet.

b. After inserting batteries, a blue light

on the remote will turn on.

c. Press any button within 5 seconds

before light turns o. A melody will

play to conirm remote pairing.

d. Repeat the process if the remote did

not pair.

2. Mount remote (optional)

a. Locate a place in the bathroom to

mount the remote so that it is visible

and reachable from the toilet.

b. Peel the tape backing o the back

of the remote control wall mount;

securely press the mount to the

location to ensure it does not fall and

damage the remote control.

c. Place the remote control into the

mount.

17

PRODUCT OPERATION

Remote Control (Cont’d)

1. Stop Button

Stops all wash and dry functions

currently operating.

2. Rear Wash / Move Button

Press once to initiate a 2-minute rear

wash. Press again to initiate nozzle

oscillation (repetitive forward and

backward nozzle movement).

3. Front Wash / Move Button

Press once to initiate a 2-minute front

wash. Press again to initiate nozzle

oscillation (repetitive forward and

backward nozzle movement).

4. Strong Wash / Move Button

Press once to initiate a 2-minute strong

wash. Press again to initiate nozzle

oscillation (repetitive forward and

backward nozzle movement).

5. Dry Button

Press once to initiate a 2-minute warm

air dryer cycle.

6. Nozzle Position Side Button

Press the left side button up or down

to adjust the nozzle position forward

and backward during a wash cycle. The

5 LED indicator lights will indicate the

dierent positions selected.

7. Nightlight Button

Press to turn the nightlight ON/OFF and

to change the color of the nightlight.

8. Seat Temperature Button and Indicator

Press to adjust the seat temperature to

1 of 4 settings (green/low: 93.2°F,

yellow/medium: 98.6°F, red/high: 104°F,

and OFF). Settings will be saved for the

next use.

9. Nozzle Cleaning Button

Press to initiate nozzle cleaning when

not sitting on the seat, or when the seat

sensor is deactivated. For more nozzle

maintenance instructions, see page 26.

10. Deodorizer Button

Deodorizer is defaulted to automatically

turn on when seated (indicator light

is ON). Press button to turn the auto

deodorizer o (indicator light is OFF).

See page 20 for more instructions.

11. Water Temperature Button and

Indicator

Press to adjust the water temperature

to 1 of 4 settings (green/low: 93.2°F,

yellow/medium: 98.6°F, red/high: 104°F,

and OFF). Settings will be saved for the

next use.

12. Gentle Wash Button

Press to initiate a gentle wash cycle

followed by a dry cycle. See page 19 for

`more instructions.

13. Water Pressure and Dry Temperature

Side Button and Indicators

Press the right-side button + or – to

adjust the water pressure during a wash

cycle. Press the same button + or – to

adjust the dry temperature during a

dry cycle. The 5 LED indicator lights

will indicate the dierent positions

selected. Settings will be saved for the

next use.

14. Five LED Indicator Lights

Indicator lights for Level 1 to Level

5 from left to right indicate nozzle

position, water pressure, and dryer

temperature level settings when those

buttons are pressed.

15. Memory User 1 and User 2 Buttons

Press User 1 or User 2 to initiate

preferred settings for a wash. User can

set nozzle position, water pressure,

oscillation, water temperature, and seat

temperature settings to memory. See

page 21 for more instructions.

18

PRODUCT OPERATION

Auxiliary Control Panel

Basic functions such as rear wash and front

wash can be used without the remote by

utilizing the auxiliary touch control panel

located on the side of the bidet seat.

1. Front Wash

Swipe inger toward the front to initiate

a front wash utilizing the last settings

used. Swipe a second time toward

the front to initiate the move function.

Swipe again to stop the move function.

2. Rear Wash

Swipe inger toward the rear to initiate a

rear wash utilizing the last settings used.

Swipe a second time toward the rear to

initiate the move function. Swipe again

to stop the move function.

3. Stop Wash

To stop the wash cycle, touch the center

of the control panel area for 1 second.

2 3 1

19

PRODUCT OPERATION

Using the Swash: Getting Started

Prepare for wash

Sit on the seat to ensure skin-to-seat

contact on the seat sensor.

Warm water wash

When ready to wash, press the Rear Wash,

Front Wash, or Strong Wash button on the

remote control once to initiate a wash.

The nozzle will perform a self-cleaning

rinse, extend into the toilet bowl, spray for

2 minutes, turn o automatically, retract,

and self-clean once again.

1. To activate the move function during

a wash, press the Rear Wash, Front

Wash, or Strong Wash button a second

time. This will initiate the nozzle to

oscillate forward and backward,

providing a wider wash spray range.

Press again to stop the move function.

2. While washing, users can adjust the

water temperature, pressure, and

nozzle position settings. See page 17

for details.

3. To stop the wash before the 2-minute

cycle ends, press the Stop button to

discontinue water low.

Warm air dryer

Press the Dry button to activate the warm air

dryer. The dryer will run for 2 minutes and

turn o automatically.

1. While the air dryer is operating, users

can adjust the dryer temperature to a

comfortable level using the Dry Temp

+ and – button on the right side of the

remote control. The dry temperature

will be relected on the 5 LED indicator

lights.

2. To stop the dryer before the 2-minute

cycle ends, press the Stop button.

Gentle wash

Auto settings within the gentle wash mode

are 40% softer than standard wash modes.

Gentle wash will begin a wash that includes:

• full nozzle extension

• water pressure set to level 2

• front wash and oscillation for 1.5 minutes

• warm air dry cycle for 2-minutes set

on level 2

NOTE: The seat has a built-in skin

conductivity sensor. The wash

functions will not work unless the

sensor detects someone is seated.

To override the seat sensor, see

instructions on page 23.

NOTE: During a gentle wash cycle,

water pressure and dryer settings may

still be adjusted.

20

Deodorizer

1. The deodorizer is defaulted to

automatically turn on when seated. When

the auto deodorizer is on, the deodorize

indicator light is ON. After leaving the

seat, it will automatically turn OFF after 1

minute.

2. To manually turn OFF the auto deodorizer,

press the Deodorize button and the

indicator light will turn OFF. The

deodorizer will remain o until it is turned

back on again by pressing the Deodorize

button.

Nightlight

1. To change the nightlight color, press the

Nightlight button repeatedly to cycle

through and select your preferred color.

2. To turn OFF the nightlight, press and hold

the Nightlight button for 3 seconds. It will

beep twice to indicate it is o.

3. To turn ON the nightlight, press the

Nightlight button for 1 second. It will beep

once to indicate it is on.

Power ON/OFF

1. To power OFF and shut down the bidet

seat, press and hold the Deodorize

button for 3 seconds. The unit will make

a tone and power OFF, shutting down the

nightlight, seat heater, and water heater.

2. To power ON, press and hold the

Deodorize button. The unit will make a

tone and power ON.

Factory Default Reset

1. Factory reset can only be performed

when the seat is not occupied.

2. To reset the bidet seat back to its

factory default program settings,

press the Stop button 4 times

within 2 seconds to clear all current

programming.

3. A tone will be heard to conirm that

the bidet seat has been reset.

PRODUCT OPERATION

Special Mode Operations

NOTE: Factory default reset only

resets programming.

La page charge ...

brondell Swash Eco Thinline T66 Le manuel du propriétaire

brondell Swash Eco Thinline T66 Le manuel du propriétaire

dans d''autres langues

Documents connexes