Parkside 279504 Original Instructions Manual

Catégorie
Outils électroportatifs
Taper
Original Instructions Manual

Ce manuel convient également à

IAN 279504
CORDLESS JIGSAW PSTDA 20-Li A1
CORDLESS JIGSAW
Translation of the original instructions
BATTERIDREVEN PENDULSTIKSAV
Oversættelse af den originale driftsvejledning
AKKU-PENDELHUBSTICHSÄGE
Originalbetriebsanleitung
SCIE SAUTEUSE PENDULAIRE
SANS FIL
Traduction des instructions d’origine
ACCU-DECOUPEERZAAG
MET PENDELSLAG
Vertaling van de originele gebruiksaanwijzing
GB / IE/NI Translation of the original instructions Page 1
DK Oversættelse af den originale driftsvejledning Side 13
FR / BE Traduction des instructions d’origine Page 25
NL / BE Vertaling van de originele gebruiksaanwijzing Pagina 39
DE / AT / CH Originalbetriebsanleitung Seite 53
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of
the device.
Før du læser, vend siden med billeder frem og bliv bekendt med alle apparatets funktioner.
Avant de lire le mode d'emploi, ouvrez la page contenant les illustrations et familiarisez-vous ensuite avec
toutes les fonctions de l'appareil.
Vouw vóór het lezen de pagina met de afbeeldingen open en maak u vertrouwd met alle functies van het
apparaat.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen
Funktionen des Gerätes vertraut.
A
BATTERY COMPATIBLE WITH ALL DEVICES OF THE SERIES „PARKSIDE X 20V TEAM“
t41&&%$03%-&44*.1"$5%3*--14#4"-J"
t$03%-&44)"..&3%3*--1"#)-J#
t$03%-&44%3*--1"#4-J$
t$03%-&44*.1"$5%3*7&31%44"-J"
t$03%-&44$*3$6-"34"81),4"-J"
t$03%-&44+*(4"8145%"-J"
t$03%-&444"#3&4"8144"-J"
t$03%-&44"/(-&(3*/%&3184"-J"
t$03%-&44.6-5*163104&500-1".'8-J"
20V max.
18V
PSTDA 20-Li A1
GB
IE
NI 1
Contents
Introduction ......................................................2
Intended use ................................................................ 2
Features ................................................................... 2
Package contents ............................................................ 2
Technical data .............................................................. 2
General Power Tool Safety Warnings ................................3
1. Work area safety .......................................................... 3
2. Electrical safety ........................................................... 3
3. Personal safety ............................................................ 4
4. Power tool use and care .................................................... 4
5. Use and handling of the cordless electrical power tool ............................. 5
6. Service .................................................................. 5
Appliance-specific safety instructions for jigsaws .................................... 5
Safety guidelines for battery chargers ............................................ 5
Original accessories/auxiliary equipment ......................................... 6
Information on saw blades ..................................................... 6
Before use .......................................................6
Charging the battery pack (see fig. A) ............................................ 6
Attaching/disconnecting the battery pack to/from the appliance ....................... 7
Checking the battery charge level ............................................... 7
Initial operation ..................................................7
Fitting/changing the saw blade ................................................. 7
Fitting the blade guard ........................................................ 7
Fitting the rip fence ........................................................... 7
Connecting the sawdust extractor ............................................... 7
Sawdust blowing function ..................................................... 7
Fitting the splinter guard ....................................................... 8
Fitting the sliding shoe ........................................................ 8
Use .............................................................8
Setting the cutting angle ....................................................... 8
Setting the stroke rate ......................................................... 8
Adjusting the pendulum stroke .................................................. 8
Switching on/off ............................................................. 8
Maintenance and cleaning ..........................................9
Kompernass Handels GmbH warranty ...............................9
Service .........................................................10
Importer ..................................................................10
Disposal ........................................................10
Translation of the original Conformity Declaration .....................11
Ordering a replacement battery ....................................12
Online ordering ............................................................12
Telephone ordering .........................................................12
PSTDA 20-Li A1
2 GB
IE
NI
CORDLESS JIGSAW
PSTDA 20-Li A1
Introduction
Congratulations on the purchase of your new appli-
ance. You have chosen a high-quality product. The
operating instructions are part of this product. They
contain important information about safety, usage
and disposal. Before using the product, please
familiarise yourself with all operating and safety
instructions. Use the product only as described and
for the range of applications specified. Please also
pass these operating instructions on to any future
owner.
Intended use
This appliance is suitable for making straight and
curved cuts as well as mitre cuts of up to 45° in
angular workpieces made of plastic, wood or
light metal. This appliance is exclusively intended
for private use in dry indoor spaces. Observe the
guidelines on saw blade types. Any other usage of
or modification to the appliance is deemed to be
improper and carries a significant risk of accidents.
The manufacturer accepts no responsibility for
damage(s) attributable to misuse.
Features
Safety lock-out for ON/OFF switch
ON/OFF switch
Handle
Release button for battery pack
Battery pack
Extraction nozzle
Switch for sawdust blower
Footplate
Sliding shoe (removable)
Pendulum stroke switch
Rip fence
Guide roller
Saw blade
Splinter guard
Insertion openings (each incl. locking screw)
Guard rail
Quick-release chuck
Blade guard
Working light
Clamping screws
Toothing
Battery charge level button
Battery display LED
High-speed charger
Red charge control LED
Green charge control LED
Package contents
1 cordless jigsaw incl. extraction nozzle and adaptor
1 high-speed battery charger
1 battery pack
1 rip fence
2 saw blades for woodworking
1 saw blade for metalworking
1 hex key
1 splinter guard
1 operating manual
Technical data
Cordless jigsaw:
PSTDA 20-Li A1
Rated voltage: 20 V
(DC)
Rated idle stroke speed: n
0
0–2700 rpm
Stroke: 20 mm
Pendulum stroke: 3 stages and fine-cut
setting
Cutting depth: wood/aluminium/metal:
80/12/5mm
Cuts: 0° - 15° - 30° - 45°
left/right
Use only the following battery to operate
the cordless tool: PAP 20 A1
Type: LITHIUM ION
Rated voltage: 20 V
(DC)
Capacity: 2.0 Ah
Cells: 5
Use only the following high-speed battery
charger to charge the cordless tool: PLG 20 A1
INPUT:
Rated voltage: 230–240 V
~
, 50 Hz
(alternating current)
Rated power
consumption: 65 W
Fuse (internal): 3.15 A
T3.15A
OUTPUT:
Rated voltage: 21.5 V (DC)
Rated current: 2.4 A
Charging time: approx. 60 min
Protection class: II / (double insulation)
PSTDA 20-Li A1
GB
IE
NI 3
Noise emission value:
Noise measurement value determined in accor-
dance with EN 60745. The A-rated noise level of
the power tool is typically as follows:
Sound pressure level: L
PA
= 80dB (A)
Uncertainty K: K
PA
= 3 dB
Sound power level: L
WA
= 91 dB (A)
Uncertainty K: K
WA
= 3 dB
Wear hearing protection!
Total vibration value:
(vector total of three directions) determined in
accordance with EN 60745:
Cutting boards: a
h,B
= 5.9 m/s
2
Uncertainty K = 1.5 m/s
2
Cutting sheet metal: a
h,M
= 7.2 m/s
2
Uncertainty K = 1.5 m/s
2
NOTE
The vibration level specified in these instruc-
tions has been measured in accordance
with the standardised measuring procedure
specified in EN 60745 and can be used to
make equipment comparisons. The specified
vibration emission value can also be used to
make an initial exposure estimate.
WARNING!
The vibration level will vary according to the
use of the power tool and may sometimes
be higher than the value specified in these
instructions. Regular use of the power tool in
this way may cause the user to underestimate
the vibration. Try to keep the vibration loads
as low as possible. Measures to reduce the
vibration load are, e.g. wearing gloves and
limiting the working time. Wherein all states
of operation must be included (e.g. times
when the power tool is switched off and times
where the power tool is switched on but run-
ning without load).
General Power
Tool Safety Warnings
WARNING!
Read all safety warnings and all instructions.
Failure to follow the warnings and instruc-
tions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future
reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-
operated (cordless) power tool.
1. Work area safety
a) Keep work area clean and well lit. Cluttered
or dark areas invite accidents.
b) Do not operate power tools in explosive atmo-
spheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
2. Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way.
Do not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electric
shock.
b) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of elec-
tric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
PSTDA 20-Li A1
4 GB
IE
NI
d) Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
e) When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces
the risk of electric shock.
f) If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
3. Personal safety
a) Stay alert, watch what you are doing and
use common sense when operating a power
tool. Do not use a power tool while you are
tired or under the influence of drugs, alcohol
or medication. A moment of inattention while
operating power tools may result in serious
personal injury.
b) Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat,
or hearing protection used for appropriate
conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools
with your finger on the switch or energising
power tools that have the switch on invites ac-
cidents.
d) Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool
may result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewel-
lery or long hair can be caught in moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
4. Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at
the rate for which it was designed.
b) Do not use the power tool if the switch does
not turn it on and off. Any power tool that can-
not be controlled with the switch is dangerous
and must be repaired.
c) Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing ac-
cessories or storing power tools. Such preven-
tive safety measures reduce the risk of starting
the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are dan-
gerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have
the power tool repaired before use. Many
accidents are caused by poorly maintained
power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
g) Use the power tool, accessories and tool bits,
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the
power tool for operations different from those
intended could result in a hazardous situation.
PSTDA 20-Li A1
GB
IE
NI 5
5. Use and handling of the cordless
electrical power tool
a) Charge a rechargeable battery unit using only
the charger recommended by the manufac-
turer. Chargers are often designed for a partic-
ular type of rechargeable battery unit. There is
the danger of fire if other types of rechargeable
battery units are used.
b) Only the rechargeable battery units supplied
are to be used with an electrical power tool.
The use of other rechargeable battery units may
lead to the danger of injury or fire.
c) When they are not being used, store re-
chargeable battery units away from paper-
clips, coins, keys, nails, screws or other small
metal objects that could cause the contacts
to be bridged. Short-circuiting the contacts of
a rechargeable battery unit may result in heat
damage or fire.
d) Fluids may leak out of rechargeable battery
units if they are misused. If this happens, avoid
contact with the fluid. If contact occurs, flush
the affected area with water. Seek additional
medical help if any of the fluid gets into your
eyes. Escaping battery fluid may cause skin
irritation or burns.
CAUTION! RISK OF EXPLOSION!
Never charge non-rechargeable
batteries!
Protect the rechargeable battery from
heat, for example from continuous
exposure to sunlight, fire, water and
moisture. There is a risk of explosion.
6. Service
a) Have your power tool serviced by a qualified
repair person using only identical replace-
ment parts. This will ensure that the safety of
the power tool is maintained.
Appliance-specific safety instructions
for jigsaws
Hold the power tool by the insulated grip-
ping surfaces when carrying out work
during which the power tool may contact
hidden power cables.Contact with a live wire
may electrify exposed metal parts of the power
tool and could give the operator an electric
shock.
Safety guidelines for battery chargers
This appliance may be used by chil-
dren aged 8 years and above and
by persons with limited physical,
sensory or mental capabilities or
lack of experience and knowledge,
provided that they are under super-
vision or have been told how to use
the appliance safely and are aware
of the potential risks. Do not allow
children to use the appliance as a
toy. Cleaning and user maintenance
tasks may not be carried out by chil-
dren unless they are supervised.
To avoid potential risks, damaged
mains cables should be replaced
by the manufacturer, their customer
service department or a similarly
qualified person.
The charger is suitable for indoor use
only.
WARNING!
If the power cord requires replacement, this
should be carried out by the manufacturer or
an approved representative to avoid safety
hazards.
PSTDA 20-Li A1
6 GB
IE
NI
Original accessories/auxiliary
equipment
Use only the accessories and additional
equipment that are specified in the operat-
ing instructions and are compatible with
the appliance.
Information on saw blades
The Parkside basic equipment includes saw blades
for use with wood and metal.
2 saw blades for general wood cutting
1 saw blade for light metals up to 5 mm
NOTE
You can use any saw blade, provided it is
fitted with a suitable mounting (single-lug
shank).
Saw blade type
suitable unsuitable
Before use
Charging the battery pack (see fig. A)
CAUTION!
Always unplug the appliance before you
remove the battery pack from or connect the
battery pack to the charger.
NOTE
Never charge the battery pack if the ambient
temperature is below 10°C or above 40°C.
If a lithium-ion battery is to be stored for an
extended period, the charge level should be
checked regularly. The optimum charge level is
between 50% and 80%. The storage climate
should be cool and dry and the ambient
temperature should be between 0°C and
50°C.
Connect the battery pack
to the high-speed
battery charger (see fig. A).
Insert the power plug into the socket. The control
LED
lights up red.
The green LED
indicates that the charging
process is complete and the battery pack
is ready.
CAUTION!
If the red control LED
flashes, this means
that the battery pack has overheated and
cannot be charged.
If the red and green control LEDs
both
flash, this means that the battery pack is
broken.
Push the battery pack
back into the appli-
ance.
Never recharge a battery pack again im-
mediately after rapid charging. There is a risk
that the battery pack will overheat and this will
reduce the lifespan of the battery.
Switch off the charger for at least 15 minutes
between successive charging sessions.
To do this, disconnect the power plug.
PSTDA 20-Li A1
GB
IE
NI 7
Attaching/disconnecting the battery
pack to/from the appliance
Inserting the battery pack:
Allow the battery pack
to click into place in
the appliance.
Removing the battery pack:
Press the release button
and remove the
battery pack.
Checking the battery charge level
Press the battery charge level button to check
the status of the battery (see also main diagram).
The status will be shown on the battery display
LED as follows:
RED/ORANGE/GREEN = maximum charge
RED/ORANGE = medium charge
RED = low charge – charge the battery
Initial operation
Fitting/changing the saw blade
Remove the battery before carrying out any work
on the power tool (e.g. maintenance, changing
tools, etc.) as well as during the transport and
storage of the power tool.
Unintentional activation of the ON/OFF switch
can result in injury.
Press the blade guard together
at the height
of the outer catches and pull it off to the front.
Turn the quick-release chuck
and hold it
in this position.
Push the required saw blade into the quick-
release chuck
as far as the stop.
Release the quick-release chuck
so that it
returns to its initial position. The saw blade is
now locked.
CAUTION! The saw blade teeth must face the
front (see fold-out page)!
Fitting the blade guard
Fit the blade guard before you connect the
appliance to a dust extractor.
Fit the blade guard
onto the appliance
so that the two outer catches engage in the
recesses in the housing.
Remove the blade guard
for working without
a dust extractor or when making mitre cuts.
To do this, press the blade guard together
at the height of the outer catches and pull it
off to the front.
Fitting the rip fence
The rip fence can be fitted on the left or right
of the appliance.
Undo both the clamping screws on the insertion
openings
.
Push the rip fence
into the insertion openings
.
Retighten the two locking screws.
Connecting the sawdust extractor
Push the extraction nozzle into the vacuum
extraction duct until it is secured in place.
Optional, depending on the diameter of the
dust and sawdust extractor.
Attach an approved dust and sawdust extractor
to the extraction nozzle
.
Wear a dust mask.
Supporting the extraction function:
Press the sawdust blower switch
to the "O"
position.
Sawdust blowing function
Switching the sawdust blowing function on:
Press the sawdust blower switch
to the
position.
PSTDA 20-Li A1
8 GB
IE
NI
Fitting the splinter guard
The splinter guard can prevent the tearing up of
the surface when sawing wood. The splinter guard
can only be used with certain sawblade types
without the sliding shoe
and only at a cutting
angle of 0°.
Press the splinter guard
into the footplate
from below (notch facing upwards).
Fitting the sliding shoe
When working on sensitive surfaces, you can fit
the sliding shoe on the baseplate to prevent
scratching the surface.
Mount the sliding shoe
onto the front of the
baseplate and press it up at the back until it
clicks into place on the baseplate .
To remove the sliding shoe
, unfasten it at
the rear of the baseplate and slide it off the
front.
Use
Setting the cutting angle
Undo the clamping screws with the supplied
hex key and pull the baseplate to the rear.
Adjust the cutting angle to 0°/15°/30°/45°
with the aid of the markings on the baseplate
.
Push the baseplate forwards so that the
locking pin engages in the toothing .
Retighten the clamping screws
with the hex
key.
NOTE
When using a cutting angle of 15°/30°/
45°, the blade guard
and the splinter
guard must be detached beforehand.
Setting the stroke rate
The ON/OFF switch has a variable speed con-
trol. Press the ON/OFF switch lightly for a low
speed. Increasing the pressure increases the speed.
NOTE
The integrated motor brake ensures rapid
stoppage.
Adjusting the pendulum stroke
You can use the pendulum stroke switch
to adjust the pendulum movement of the saw
blade . You can achieve fine, clean-cut edges
without pendulum movement (setting "0").
Deactivate pendulum movement when working
on thin workpieces. You can achieve an increas-
ingly fast work rate if the pendulum stroke is
activated (settings 1–3).
Switching on/off
Switching the appliance on:
Push the safety lock-out
to the left or right
and keep it pressed.
Press the ON/OFF switch
.
Once the saw is running, you can release
the safety lock-out . The working light
illuminates when the ON/OFF switch is
depressed lightly or completely. This provides
illumination of the work area in poor lighting
conditions.
Switching the appliance off:
Release the ON/OFF switch
.
PSTDA 20-Li A1
GB
IE
NI 9
Maintenance and cleaning
WARNING! RISK OF INJURY! Always
switch the appliance off and remove
the battery before carrying out any
work on the appliance.
The appliance must always be kept clean, dry
and free from oil or grease.
Use a soft, dry cloth to clean the housing.
If a lithium-ion battery is to be stored for an
extended period, the charge level should be
checked regularly. The optimum charge level is
between 50% and 80%. The optimum storage
environment is cool and dry.
Clean the appliance after completing your
sawing work.
Remove any dirt (e.g. sawdust). If necessary,
clean the saw blade mount with a brush or
compressed air.
Kompernass Handels GmbH
warranty
Dear Customer,
This appliance has a 3-year warranty valid from
the date of purchase. If this product has any faults,
you, the buyer, have certain statutory rights. Your
statutory rights are not restricted in any way by the
warranty described below.
Warranty conditions
The validity period of the warranty starts from the
date of purchase. Please keep your original receipt
in a safe place. This document will be required as
proof of purchase.
If any material or production fault occurs within
three years of the date of purchase of the product,
we will either repair or replace the product for you
at our discretion. This warranty service is dependent
on you presenting the defective appliance and
the proof of purchase (receipt) and a short written
description of the fault and its time of occurrence.
If the defect is covered by the warranty, your product
will either be repaired or replaced by us. The repair
or replacement of a product does not signify the
beginning of a new warranty period.
Warranty period and statutory claims for
defects
The warranty period is not prolonged by repairs
effected under the warranty. This also applies to
replaced and repaired components. Any damage
and defects present at the time of purchase must
be reported immediately after unpacking. Repairs
carried out after expiry of the warranty period shall
be subject to a fee.
Scope of the warranty
This appliance has been manufactured in accordance
with strict quality guidelines and inspected meticu-
lously prior to delivery.
The warranty covers material faults or production
faults. The warranty does not extend to product parts
subject to normal wear and tear or fragile parts such
as switches, batteries, baking moulds or parts made
of glass.
The warranty does not apply if the product has been
damaged, improperly used or improperly maintained.
The directions in the operating instructions for the
product regarding proper use of the product are
to be strictly followed. Uses and actions that are
discouraged in the operating instructions or which
are warned against must be avoided.
This product is intended solely for private use and
not for commercial purposes. The warranty shall be
deemed void in cases of misuse or improper handling,
use of force and modifications/repairs which have
not been carried out by one of our authorised
Service centres.
Warranty claim procedure
To ensure quick processing of your case, please
observe the following instructions:
Please have the till receipt and the item number
(e.g. IAN 12345) available as proof of purchase.
You will find the item number on the type plate,
an engraving on the front page of the instructions
(bottom left), or as a sticker on the rear or
bottom of the appliance.
If functional or other defects occur, please
contact the service department listed either by
telephone or by e-mail.
PSTDA 20-Li A1
10 GB
IE
NI
You can return a defective product to us free of
charge to the service address that will be provided
to you. Ensure that you enclose the proof of
purchase (till receipt) and information about
what the defect is and when it occurred.
You can download these instructions
along with many other manuals,
product videos and software on
www.lidl-service.com.
Service
WARNING!
Have the power tool repaired by the service
centre or a qualified electrician and only
using genuine replacement parts. This will
ensure that the safety of the appliance is
maintained.
Always ensure that the power plug or
the mains cable is replaced only by the
manufacturer of the appliance or by an
approved customer service provider. This
will ensure that the safety of the appliance is
maintained.
Service Great Britain
Tel.: 0871 5000 720 (£ 0.10/Min.)
Service Ireland
Tel.: 1890 930 034
(0,08 EUR/Min., (peak))
(0,06 EUR/Min., (off peak))
IAN 279504
Importer
Please note that the following address is not the
service address. Please contact the service
address provided.
KOMPERNASS HANDELS GMBH
BURGSTRASSE 21
44867 BOCHUM
GERMANY
www.kompernass.com
Disposal
The packaging is made from environmen-
tally friendly material and can be dis-
posed of at your local recycling plant.
Do not dispose of power tools in
your normal household waste!
European Directive 2012/19/EU requires that
worn-out power tools be collected separately and
recycled in an environmentally compatible manner.
Do not dispose of batteries in your
normal household waste!
Defective or worn-out rechargeable batteries must
be recycled according to Directive 2006/66/EC.
Take the battery pack and/or appliance to a nearby
collection facility.
Please consult your local authorities regarding
suitable disposal of worn out power tools/battery
packs.
PSTDA 20-Li A1
GB
IE
NI 11
Translation of the original Conformity Declaration
We, KOMPERNASS HANDELS GMBH, document officer: Mr. Semi Uguzlu, BURGSTR. 21,
44867 BOCHUM, GERMANY, hereby declare that this product complies with the following standards,
normative documents and EC directives:
Machinery Directive
(2006/42/EC)
EC Low Voltage Directive
(2014/35/EU)
EMC (Electromagnetic Compatibility)
(2014/30/EU)
RoHS Directive
(2011/65/EU)*
*The manufacturer bears the full responsibility for compliance with this conformity declaration. The object
of the declaration described above complies with the requirements of the Directive 2011/65/EU of the Euro-
pean Parliament and Council of 8 June 2011 on the limitations of use of certain dangerous substances in
electrical and electronic appliances.
Applied harmonised standards:
EN 60745-1: 2009 / A11: 2010
EN 60745-2-11: 2010
EN 62233: 2008
EN 55014-1: 2006 / A2: 2011
EN 55014-2: 2015
EN 60335-1: 2012 / A11: 2014
EN 60335-2-29: 2004 / A2:2010
EN 61000-3-2: 2014
EN 61000-3-3: 2013
Type designation of machine:
Cordless jigsaw PSTDA 20-Li A1
Year of manufacture: 10 - 2016
Serial number: IAN 279504
Bochum, 30/09/2016
Semi Uguzlu
- Quality Manager -
We reserve the right to make technical changes in the context of further product development.
PSTDA 20-Li A1
12 GB
IE
NI
Ordering a replacement battery
If you want to order a replacement battery for your appliance, you can do so easily via the Internet on
www.kompernass.com or by telephone.
The price of the replacement battery is €20, including VAT and shipping. Due to limited stocks, this item
may sell out in a relatively short time.
Online ordering
To order a replacement battery from the Accessories Shop:
Use your Internet browser to visit www.kompernass.com.
Click on the corresponding flag on the right hand side at the bottom of the page to select the desired
country and language.
Click on the tab "Accessory Shop" and then select the appropriate replacement battery under the
heading "Topseller".
After you have placed the rechargeable battery in the shopping basket, click the "Checkout" button
and follow the on-screen instructions to complete the ordering process.
NOTE
Online ordering of replacement parts is not possible in all countries. In this case, please contact the
Service hotline.
The promotion is limited to one battery per customer/appliance and also to a timeline of two months
after the promotion period. Thereafter, the replacement battery can be ordered as a replacement
part under other conditions.
Telephone ordering
Service Great Britain
Tel.: 0871 5000 720 (£ 0.10/Min.)
Service Ireland
Tel.: 1890 930 034 (0,08 EUR/Min., (peak))
(0,06 EUR/Min., (off peak))
To ensure that your order is processed swiftly, have the article number of your appliance to hand
(e.g. IAN 279504) in case of questions. The article number can be found on the type plate or the
title page of these instructions.
PSTDA 20-Li A1
DK 13
Indholdsfortegnelse
Indledning ......................................................14
Anvendelsesområde ......................................................... 14
Udstyr ....................................................................14
Pakkens indhold ............................................................14
Tekniske data ..............................................................14
Generelle sikkerheds anvisninger til elværktøjer ......................15
1. Sikkerhed på arbejdspladsen ............................................... 15
2. Elektrisk sikkerhed ........................................................15
3. Personsikkerhed .......................................................... 16
4. Anvendelse og behandling af elværktøjet ......................................16
5. Anvendelse og behandling af det genopladelige værktøj .......................... 17
6. Service .................................................................17
Specielle sikkerhedsanvisninger for stiksave .......................................17
Sikkerhedsanvisninger for opladere .............................................17
Originalt tilbehør / originalt ekstraudstyr .........................................17
Oplysninger om savklinger .................................................... 17
Før første brug ..................................................18
Opladning af batteripakke (se fig. A) ...........................................18
Indsætning / udtagning af den genopladelige batteripakke ..........................18
Kontrol af det genopladelige batteris tilstand. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Første brug .....................................................18
Montering/udskiftning af savklinge .............................................18
Montering af beskyttelsesafdækning ............................................19
Montering af parallelanslag ...................................................19
Tilslutning af spånudsugning ..................................................19
Spånblæsefunktion ..........................................................19
Montering af spånbeskytter ...................................................19
Montering af glidesko .......................................................19
Betjening .......................................................20
Indstilling af snitvinkel ........................................................20
Indstilling af slagfrekvens ..................................................... 20
Indstilling af pendulslag ......................................................20
Sådan tændes / slukkes produktet .............................................. 20
Vedligeholdelse og rengøring ......................................20
Garanti for Kompernass Handels GmbH .............................20
Service .........................................................22
Importør ..................................................................22
Bortskaffelse ....................................................22
Oversættelse af den originale overensstemmelseserklæring ............23
Bestilling af genopladeligt reservebatteri ............................24
Online-bestilling ............................................................ 24
Telefonisk bestilling .......................................................... 24
PSTDA 20-Li A1
14 DK
BATTERIDREVEN
PENDULSTIKSAV PSTDA 20-Li A1
Indledning
Tillykke med købet af dit nye produkt. Du har valgt
et produkt af høj kvalitet. Betjeningsvejledningen er
en del af dette produkt. Den indeholder vigtige infor-
mationer om sikkerhed, anvendelse og bortskaffelse.
Du bør sætte dig ind i alle produktets betjenings- og
sikkerhedsanvisninger før brug. Brug kun produktet
som beskrevet og kun til de angivne anvendelsesom-
råder. Lad vejledningen følge med produktet, hvis du
giver det videre til andre.
Anvendelsesområde
Produktet er beregnet til lige og kurvede snit samt
geringssnit på op til 45° på kantede emner i plast,
træ og letmetal. Produktet er udelukkende beregnet
til privat brug i tørre rum. Vær opmærksom på anvis-
ningerne vedrørende savklingetyper. Enhver anden
anvendelse eller ændring af produktet anses for at
være uden for anvendelsesområdet og indebærer
betydelige farer for uheld. Producenten påtager
sig intet ansvar for skader, der opstår som følge af
anvendelse uden for anvendelsesområdet.
Udstyr
Startspærre for tænd-/sluk-knap
Tænd-/sluk-knap
Greb
Knap til frigørelse af batteripakke
Genopladelig batteripakke
Udsugningsstuds
Knap til spånblæseanordning
Bundplade
Glidesko (aftagelig)
Pendulslagsknap
Parallelanslag
ringsrulle
Savklinge
Spånbeskytter
Indføringsåbninger (inkl. stopskrue)
Beskyttelsesbøjle
Hurtigskiftepatron
Beskyttelsesafdækning
Arbejdslys
Klemskruer
Fortanding
Knap til kontrol af batteriets tilstand
Display-LED for genopladeligt batteri
Hurtigoplader
Rød LED til kontrol af opladning
Grøn LED til kontrol af opladning
Pakkens indhold
1 batteridreven pendulstiksav inkl. udsugningsstuds
og adaptere
1 hurtigladeapparat til genopladelige batterier
1 pakke genopladelige batterier
1 parallelanslag
2 savklinger til træforarbejdning
1 savklinge til metalforarbejdning
1 sekskantnøgle
1 spånbeskytter
1 betjeningsvejledning
Tekniske data
Batteridreven pendulstiksav:
PSTDA 20-Li A1
Mærkespænding: 20 V
(jævnstrøm)
Tomgangsslagfrekvens: n
0
0 - 2700 min
-1
Slaglængde: 20 mm
Pendulslag: 3 trin og indstilling
af finsnit
Skæredybde: Træ/aluminium/metal:
80/12/5 mm
Snitvinkel: 0° - 15° - 30° - 45°
mod venstre/højre
Brug kun følgende genopladelige batteri til
drift af værktøjet: PAP 20 A1
Type: LITHIUM-ION
Mærkespænding: 20 V
(jævnstrøm)
Kapacitet: 2,0 Ah
Celler: 5
Brug kun følgende oplader til opladning af
værktøjets genopladelige batteri: PLG 20 A1
INDGANG / input:
Mærkespænding: 230 - 240 V
~
, 50 Hz
(vekselstrøm)
Nominelt effektforbrug: 65 W
Sikring (intern): 3,15 A
T3.15A
UDGANG / output:
Mærkespænding: 21,5 V (jævnstrøm)
Mærkestrøm: 2,4 A
Opladningstid: ca. 60 min
Beskyttelsesklasse: II / (dobbeltisolering)
PSTDA 20-Li A1
DK 15
Støjemissionsværdi:
Måleværdi for støj beregnet iht. ENISO 60745.
Det A-vægtede støjniveau for elværktøjet er typisk
som følger:
Lydtrykniveau: L
PA
= 80 dB (A)
Usikkerhed K: K
PA
= 3 dB
Lydeffektniveau: L
WA
= 91 dB (A)
Usikkerhed K: K
WA
= 3 dB
Bær høreværn!
Samlede vibrationsværdier:
(vektorsum i tre retninger) beregnet iht. EN60745:
Savning af spånplader: a
h,B
= 5,9 m/s
2
Usikkerhed K = 1,5 m/s
2
Savning af metalplader: a
h,M
= 7,2 m/s
2
Usikkerhed K = 1,5 m/s
2
BEMÆRK
Vibrationsniveauet, som er angivet i disse
anvisninger, er målt med en målemetode, der
er standardiseret efter EN60745, og som kan
anvendes til sammenligning af elværktøjer. Den
angivne vibrationsemissionsværdi kan også
anvendes til en indledende vurdering af faren
ved vibrationsniveauet.
ADVARSEL!
Vibrationsniveauet ændrer sig afhængigt
af elværktøjets anvendelse og kan i mange
tilfælde ligge over værdien, der er angivet
i disse anvisninger. Vibrationsbelastningen
kan undervurderes, hvis elværktøjet jævnligt
anvendes på denne måde. Prøv at holde
belastningen forårsaget af vibrationer så lav
som muligt. Vibrationsbelastningen kan f.eks.
reduceres ved brug af handsker under anven-
delse af værktøjet samt ved nedsættelse af
den tid, værktøjet bruges. Her skal der tages
hensyn til hele driftscyklussen (f.eks. perioder,
hvor elværktøjet er slukket, og perioder, hvor
det er tændt, men kører uden belastning).
Generelle sikkerheds-
anvisninger til
elværktøjer
ADVARSEL!
Læs alle sikkerhedsanvisninger og -instruktio-
ner. Hvis de angivne sikkerhedsanvisninger og
-instruktioner ikke overholdes, kan det medføre
elektrisk stød, brand og/eller alvorlige kvæ-
stelser.
Opbevar sikkerhedsanvisningerne og
-instruktionerne til senere brug.
Begrebet "elværktøj", der anvendes i sikkerhedsanvis-
ningerne, henviser både til elværktøj, der anvendes
med ledning til lysnettet, og batteridrevet elværktøj
(uden strømledning).
1. Sikkerhed på arbejdspladsen
a) Hold arbejdspladsen ren og godt oplyst. Rod
og dårligt oplyste arbejdspladser kan medføre
uheld.
b) Arbejd aldrig med elværktøj i eksplosionsfarli-
ge omgivelser, hvor der befinder sig brænd-
bare væsker, gasser eller støv. Elværktøj danner
gnister, som kan antænde støvet eller dampene.
c) Hold børn og andre personer på afstand, når
elværktøjet bruges. Hvis du bliver distraheret,
kan du miste kontrollen over produktet.
2. Elektrisk sikkerhed
a) Elværktøjets tilslutningsstik skal passe til stikkon-
takten. Stikket må ikke ændres på nogen måde.
Der må ikke bruges adapterstik sammen med
beskyttelsesjordet elværktøj. Uændrede stik
og de rigtige stikkontakter reducerer risikoen for
elektrisk stød.
b) Undgå kropskontakt med jordforbundne over-
flader som f.eks. rør, radiatorer, komfurer og
køleskabe. Der er øget risiko for elektrisk stød,
hvis din krop har jordforbindelse.
c) Hold elværktøjet væk fra regn og fugt.
Hvis der trænger vand ind i elværktøjet, øges
risikoen for elektrisk stød.
PSTDA 20-Li A1
16 DK
d) Brug ikke ledningen til noget, den ikke er
beregnet til, f.eks. til at bære eller hænge
værktøjet op i eller til at trække stikket ud af
stikkontakten. Hold ledningen på afstand af
varme, olie, skarpe kanter eller produktets
bevægelige dele. Beskadigede eller sammenfil-
trede ledninger øger risikoen for elektrisk stød.
e) Hvis du anvender elværktøj udendørs, skal
der bruges en forlængerledning, som er god-
kendt til brug udendørs. Når du anvender en
forlængerledning, der er beregnet til udendørs
brug, reduceres risikoen for elektrisk stød.
f) Hvis det ikke er muligt at undgå at bruge
elværktøjet i fugtige omgivelser, skal der
installeres en fejlstrømsafbryder. Installation
af en fejlstrømsafbryder reducerer risikoen for
elektrisk stød.
3. Personsikkerhed
a) Vær altid opmærksom og bevidst om, hvad du
laver, og arbejd fornuftigt med elværktøjet.
Brug ikke elværktøjet, hvis du er ukoncentreret
eller påvirket af narkotika, alkohol eller medi-
cin. Selv et øjebliks uopmærksomhed ved brug
af elværktøjet kan medføre alvorlige kvæstelser.
b) Brug personligt beskyttelsesudstyr, og bær altid
beskyttelsesbriller. Når du bruger personligt be-
skyttelsesudstyr som f.eks. støvmaske, skridsikre
sikkerhedssko, beskyttelseshandsker, sikkerheds-
hjelm og høreværn afhængigt af elværktøjets type
og anvendelse, reduceres risikoen for kvæstelser.
c) Undgå uønsket igangsætning. Kontrollér, at el-
værktøjet er slukket, før du forbinder det med
elforsyningen og/eller tilslutter batteriet, tager
elværktøjet op eller bærer det. Hvis du har
en finger på kontakten, eller hvis elværktøjet er
tændt, mens du bærer det, kan der opstå uheld.
d) Fjern indstillingsværktøj eller skruenøgler, før
du tænder for elværktøjet. Hvis der sidder et
værktøj eller en skruenøgle på en roterende del
af elværktøjet, kan det medføre personskader.
e) Undgå unormale kropsstillinger. Sørg for, at
du står sikkert, og hold altid balancen. Derved
kan du bedre kontrollere elværktøjet i uventede
situationer.
f) Bær velegnet påklædning. Bær ikke løstsid-
dende tøj eller smykker. Hold hår, tøj og hand-
sker på afstand af dele, der bevæger sig. Løst
tøj, smykker eller hår kan gribes fat af dele, der
bevæger sig.
g) Hvis der monteres opsugnings- og opsamlings-
anordninger, skal disse tilsluttes og anvendes
korrekt. Anvendelse af denne type anordninger
nedsætter støvrisikoen.
4. Anvendelse og behandling af
elværktøjet
a) Overbelast ikke elværktøjet. Brug et elværk-
tøj, der er egnet til arbejdet. Du arbejder bed-
re og mere sikkert i det angivne effektområde,
hvis du bruger det rigtige elværktøj.
b) Brug ikke elværktøj med defekt kontakt.
Elværktøj, som ikke længere kan tændes og
slukkes, er farligt og skal repareres.
c) Tag stikket ud af stikkontakten, og/eller fjern
batteriet, før du foretager indstillinger på
værktøjet eller tilbehørsdelene eller lægger
værktøjet fra dig. Disse forholdsregler forhin-
drer, at elværktøjet starter ved en fejl.
d) Opbevar elværktøj uden for børns rækkevid-
de, når værktøjet ikke anvendes. Personer,
som ikke kender produktet, eller som ikke har
læst disse anvisninger, må ikke bruge produk-
tet. Elværktøj er farligt, hvis det anvendes af uer-
farne personer.
e) Vedligehold elværktøjet omhyggeligt.
Kontrollér, om bevægelige dele fungerer, som
de skal og ikke sætter sig fast, om dele er
defekte eller så beskadigede, at elværktøjets
funktion er påvirket. Få beskadigede dele
repareret, inden du bruger produktet. Mange
uheld skyldes dårligt vedligeholdt elværktøj.
f) Hold skærende værktøjer skarpe og rene. Om-
hyggeligt vedligeholdt værktøj med skarpe skær
sætter sig ikke så ofte fast og er lettere at styre.
g) Brug elværktøj, tilbehør, udskiftelige dele osv.
iht. disse anvisninger. Tag hensyn til arbejds-
betingelserne og det arbejde, der skal udføres.
Anvendelse af elværktøj til andet end de til-
tænkte anvendelsesområder kan føre til farlige
situationer.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69

Parkside 279504 Original Instructions Manual

Catégorie
Outils électroportatifs
Taper
Original Instructions Manual
Ce manuel convient également à

dans d''autres langues