Acson E Series Guide d'installation

CEILING CASSETTE

SPLIT TYPE AIR CONDITIONER

(E Series)

CEILING CASSETTE

INSTALLATION MANUAL

IM-CKE-0209(0)-ACSON

Part No.: R08019032819

1-1

English

OUTLINE AND DIMENSIONS

AB CDEF GHIJK

(5)CK20/25/28E(R) 820 820 340 300 40 990 990 627 627 607 430

(32.3) (32.3) (13.4) (11.8) (1.6) (39.0) (39.0) (24.7) (24.7) (23.9) (16.9)

(5)CK40/50E(R) 820 820 375 335 40 990 990 627 627 607 430

(32.3) (32.3) (14.8) (13.2) (1.6) (39.0) (39.0) (24.7) (24.7) (23.9) (16.9)

Indoor Unit (5)CK20/25/28/40/50E(R) Series

• (With Wireless Remote Control & With Wired Remote Control)

All dimensions are in mm/(in)

A

B

C

D

E

F

H

K

J

I

G

Outdoor Unit (5)SL20/25/28C(R) Series

All dimensions are in mm/(in)

ABCDEFGH I JKLMNOPQRST

(5)SL20C(R) 855 628 328 508 181 44 93 149 101 113 603 126 164 15 49 3 23 73 75 362

(33.7) (24.7) (12.9) (20.0) (7.1) (1.7) (3.7) (5.9) (4.0) (4.4) (23.7) (5.0) (6.5) (0.6) (1.9) (0.1) (0.9) (2.9) (3.0) (14.3)

(5)SL25/28C(R) 855 730 328 513 182 44 93 149 101 113 603 126 164 15 47 3 23 73 75 362

(33.7) (28.7) (12.9) (20.2) (7.2) (1.7) (3.7) (5.9) (4.0) (4.4) (23.7) (5.0) (6.5) (0.6) (1.9) (0.1) (0.9) (2.9) (3.0) (14.3)

N

L

KL

TN

M

A

D

O

P

BQ

RS

C

HG

FE

IJ

FOR 25/28CR ONLY

Model

Dimension

Model

Dimension

1-2

Outdoor Unit (5)SL35/40/50C(R) Series

A

B

G

D

E

H

I

J

L

M

O

C

F

All dimensions are in mm/(in)

K

N

ABCDEFGHI JKLMNOP

(5)SL35/40/50C(R)

141.5 746.5 141.5 20 448 20 1030 850 25 50 85 400 40 320 40 75

(5.6) (29.4) (5.6) (0.8) (17.6) (0.8) (40.6) (33.5) (1.0) (2.0) (3.3) (15.7) (1.6) (12.6) (1.6) (2.9)

P

Model

Dimension

1-3

English

! CAUTION

Please take note of the following important points when

installing.

• Do not install the unit where leakage of flammable

gas may occur.

If gas leaks and accumulates around the unit, it

may cause fire ignition.

• Ensure that drainage piping is connected properly.

If the drainage piping is not connected properly, it

may cause water leakage which will dampen the

furniture.

• Do not overcharge the unit.

This unit is factory pre-charged.

Overcharge will cause over-current or damage to

the compressor.

• Ensure that the unit’s panel is closed after service

or installation.

Unsecured panels will cause the unit to operate

noisily.

• Sharp edges and coil surfaces are potential locations

which may cause injury hazards.

Avoid from being in contact with these places.

• Before turning off the power supply, set the remote

controller’s ON/OFF switch to the “OFF” position

to prevent the nuisance tripping of the unit. If this is

not done, the unit’s fans will start turning automatically

when power resumes, posing a hazard to service

personnel or the user.

• Do not operate any heating apparatus too close to

the air conditioner unit. This may cause the plastic

panel to melt or deform as a result of the excessive heat.

• Ensure the color of wires of the outdoor unit and

the terminal markings are same to the indoors

respectively.

• IMPORTANT : DO NOT INSTALL OR USE THE

AIR CONDITIONER UNIT IN A LAUNDRY

ROOM.

• Don’t use joined and twisted wires for incoming

power supply.

! WARNING

• Installation and maintenance should be performed by

qualified persons who are familiar with local code and

regulation, and experienced with this type of appliance.

• All field wiring must be installed in accordance with

the national wiring regulation.

• Ensure that the rated voltage of the unit corresponds to

that of the name plate before commencing wiring work

according to the wiring diagram.

• The unit must be GROUNDED to prevent possible

hazard due to insulation failure.

• All electrical wiring must not touch the refrigerant

piping, or any moving parts of the fan motors.

• Confirm that the unit has been switched OFF before

installing or servicing the unit.

• Disconnect from the main power supply before servicing

the air conditioner unit.

• DO NOT pull out the power cord when the power is

ON. This may cause serious electrical shocks which

may result in fire hazards.

• Keep the indoor and outdoor units, power cable and

transmission wiring, at least 1m from TVs and radios,

to prevent distorted pictures and static. {Depending on

the type and source of the electrical waves, static may

be heard even when more than 1m away}.

This manual provides the procedures of installation to ensure a safe and good standard of operation for the air

conditioner unit.

Special adjustment may be necessary to suit local requirements.

Before using your air conditioner, please read this instruction manual carefully and keep it for future reference.

INSTALLATION MANUAL

SAFETY PRECAUTIONS

Disposal requirements

Your air conditioning product is marked with this symbol. This means that electrical and electronic products shall

not be mixed with unsorted household waste.

Do not try to dismantle the system yourself: the dismantling of the air conditioning system, treatment of the refrigerant,

of oil and of other parts must be done by a qualified installer in accordance with relevant local and national legislation.

Air conditioners must be treated at a specialized treatment facility for re-use, recycling and recovery. By ensuring

this product is disposed of correctly, you will help to prevent potential negative consequences for the environment

and human health. Please contact the installer or local authority for more information.

Batteries must be removed from the remote controller and disposed of separately in accordance with relevant local

and national legislation.

NOTICE

1-4

Important information regarding the refrigerant used

This product contains fluorinated greenhouse gases covered by the Kyoto Protocol.

Do not vent gases into the atmosphere.

Refrigerant type: R410A

GWP

(1)

value: 1975

(1)

GWP = global warming potential

Please fill in with indelible ink,

 1 the factory refrigerant charge of the product,

 2 the additional refrigerant amount charged in the field and

 1 + 2 the total refrigerant charge

on the refrigerant charge label supplied with the product.

The filled out label must be adhered in the proximity of the product charging port (e.g. onto the inside of the service cover).

1 factory refrigerant charge of the product:

see unit name plate

(2)

2 additional refrigerant amount charged in the field

3 total refrigerant charge

4 contains fluorinated greenhouse gases covered by the Kyoto Protocol

5 outdoor unit

6 refrigerant cylinder and manifold for charging

(2)

In case of multiple indoor systems, only 1 label must be adhered*, mentioning the total factory refrigerant charge of all

indoor units connected in the refrigerant system.

Periodical inspections for refrigerant leaks may be required depending on European or local legislation. Please contact your

local dealer for more information.

* on the outdoor unit

IMPORTANT

1-5

English

Indoor Unit

Outdoor Unit

Drain Hose

Front Panel

Air Filter

(behind the grille)

Air Discharge Louver

Air Intake Grille

Refrigerant Piping

Air Discharge

Wireless Remote Control

Air Discharge Louver

Remote Control

INSTALLATION DIAGRAM

Air Intake

INSTALLATION OF THE INDOOR UNIT

Preliminary Site Survey

Be sure to read this manual before installing the air-conditioner indoor unit.

• Electrical supply and installation is to conform to local authority’s (e.g. National Electrical Board) codes and regulations.

• Voltage supply fluctuation must not exceed

+

10% of rated voltage. Electricity supply lines must be independent of welding

transformers which can cause high supply fluctuation.

• Ensure that the location is convenient for wiring, piping and drainage.

• Do not exert pressure on the resin parts when opening the unit or when moving it after opening.

• Do not move the unit from packaging while moving, until it reaches the installation site. Use safe material or protection

plates when unpacking it or lifting it to avoid damage or scratches to the unit.

• Check the following accessories are include with your unit:

a) Battery (2pcs) f) Screw M4 x 6 (2pcs)

b) Screw M6 x 40 (4pcs) g) Cover lock grille (2pcs)

c) Washer, flat OD19 x ID17 x t1.0 (4pcs) h) Operation Manual (1pc)

d) Screw M4 x 20 (2pcs) i) Installation Manual (1pc)

e) Handset (1pc) j) Drain hose (1pc)

Min. 0.5m Min. 0.5m Min. 0.5m

Max. 0.3m

Max. 3.0m

Min. 1.0m

Floor

Obstacle

Beam

1-6

• Ensure a location where:

a) Drainage can be done easily.

b) Convenient for wiring and piping.

c) Which have enough space for installation and service work.

d) Where no risk of flammable gas leakage.

e) When free from any obstacles in path of cool air discharge and warm air return and must allow spreading of air throughout

the room (near the center of the room).

f) Must be provided clearance for indoor unit from the wall and obstacles as shown in figure below.

g) The installation place must be strong enough to support a load 4 times the indoor unit weight to avoid amplifying noise

and vibration.

h) The installation place (hanging ceiling surface) must be assuring levelness and the height in the ceiling is 350mm or

more.

i) The indoor unit must be away from heat and steam sources (avoid installing it near an entrance).

Unit Installation

• Measure and mark the position for the hanging rod. Drill

the hole for the angle nut on the ceiling and fix the hanging

rod.

• The installation template is extended according to

temperature and humidity. Check on dimensions in use.

• The dimensions of the installation template are the same

as those of the ceiling opening dimensions.

• Before ceiling laminating work is completed, be sure to

fit the installation template to the indoor unit.

NOTE

Be sure to discuss the ceiling drilling work with the

installers concerned.

770.0mm (Hanging Rod)

622.0mm (Hanging Rod)

Piping Direction

880.0~990.0mm (Ceiling Opening Site = 890mm)

990.0mm

880.0~990.0mm (Ceiling Opening Site)

990.0mm

• Confirm the pitch of the hanging rod is 770mm × 622mm

sharp.

• Hold the unit and hang it on the hanging rod with the nut

and washer.

• Adjust the unit height to 30.0mm between the indoor unit

bottom surface and the ceiling surface.

• Confirm with a level gauge that the unit is installed

horizontally and tighten the nut and bolt to prevent unit

falling and vibration.

• Open the ceiling board along the outer edge of the paper

installation template.

Unit Hanging

Indoor Unit

30.0mm

Ceiling

Board

1-7

English

Main Drain Pipe

Feed Water

Flexible Drain Hose

Drain Test

NOTE

This Indoor Unit uses a drain pump for condensed water drainage. Install the unit horizontally to prevent water

leakage or condensation around the air outlet.

Indoor Unit

Pipe Clamp

Good

Bad

Drain Piping Work

• Drain pipe must be in downward gradient for smooth

drainage.

• Avoid installing the drain pipe in up and down slope to

prevent reversed water flow.

• During the drain pipe connection, be careful not to exert

extra force on the drain connector at indoor unit.

• The outside diameter of the drain connection at the

flexible drain hose is 20mm.

• Be sure to execute heat insulation (polyethylene foam

with thickness more than 8.0mm) on the drain piping to

avoid the condensed water dripping inside the room.

• Connect the main drain pipe to the flexible drain hose.

• Feed water from flexible drain hose to check the piping

for leakage.

• When the test is completed, connect the flexible drain

hose to the drain connector on the indoor unit.

• The front panel can only be fitted in one direction, follow the piping direction. (Follow piping arrow sticker on front

panel)

• Be sure to remove the installation template before installing the front panel.

Panel Installation

Open

Screw

• Open the air intake grille by pulling back the catchers and removing it together with filter from panel.

• Install the front frame panel onto the indoor unit by 4 screws and tighten it completely to prevent cool air leakage.

• Connect the LED wire and air swing wire to the indoor unit.

• The air swing connector must put inside the control box after connected.

From

Unit

Control

Box

From

Front

Panel

LED Wire

Air Swing Wire

1-8

Cover Lock Grille (The moving part protection for user direct touching)

Cover lock grill must be installed as the figure below.

If the unit need to be service, steps below shall be followed:

1. Confirm that the unit had been switched off before servicing the unit.

2. Use screwdriver to unlock the screw on the cover lock grille.

3. Remove the cover lock grille and open the intake grille for the service purpose.

4. Install the intake grille and screw the cover lock grille after service and make sure the unit is proper install.

Frame

Intake Grille

Cover Lock Grille

(2pcs)

Screw M4 x 6

(2pcs)

NOTE

Install the front frame panel firmly to prevent cool air leakage which will cause condensation and water dripping.

Indoor Unit

Cool

Air

Ceiling Board

Panel

Air Leak

Good Installation

Bad Installation

Cool

Air

Air Leak

Ceiling Board

Panel

1-9

English

Wires Installation

Figure 1 and Figure 2 shows the location of cover wire in CKE unit.

Steps to install power supply wires and wires from outdoor unit.

1. Remove wire cover by removing 2 screws as shown in Figure 3.

2. Wires will go through the hole as shown in figure 4 and 5 respectively without crossing the height of the hole.

3. After that, wire cover will be assembled back to close the wire.

Figure 1

Figure 2

Figure 4

Figure 3

Figure 5

1-10

INSTALLATION OF THE OUTDOOR UNIT

Preliminary Site Survey

• A place protected from rain, direct sunlight and well-ventilated wherever practicable.

• A place capable of bearing the weight of the outdoor unit and isolating noise and vibration.

• A place where there are no obstruction of air flow into or out the unit.

• Do not put any object which may become obstacle for the air flow into or out the outdoor unit.

• The location must not be susceptible to high concentration dust, oil, salt or sulfide gas.

• Select the coolest possible place where intake air temperature is not greater than the outside air temperature (maximum

45°C).

SL series A B C D

Min. distance, mm (in)

300 1000 300 500

(11.8) (39.4) (11.8) (19.7)

Outdoor Unit Installation

• Install the outdoor unit firmly and horizontally. Maintain a space clearance from the obstruction as shown in below for

servicing and air ventilation.

AB

C

D

REFRIGERANT PIPING WORK

Refrigerant piping is important in particular. Refrigeration cycle of the split air conditioner is realized

by the perfect piping work.

Piping Length And Elevation

If the piping is too long, both the capacity and reliability of unit will drop. As the number of bends increase, resistance to

flow of refrigerant system increases, thus lowering cooling capacity and as a result the compressor may become defective.

Always choose the shortest path and follow the recommendation as tabulated below.

Model Indoor (5)CK20E(R) (5)CK25E(R) (5)CK28E(R) (5)CK40E(R) (5)CK40E(R) (5)CK50E(R)

Outdoor (5)SL20C(R) (5)SL25C(R) (5)SL28C(R) (5)SL35C(R) (5)SL40C(R) (5)SL50C(R)

Max. length (m) 15m 15m 15m 45m 45m 45m

Max. elevation (m) 8m 8m 8m 25m 25m 25m

Max. no. of bends 10 10 10 10 10 10

Liquid pipe size 1/4" 3/8" 3/8" 3/8" 3/8" 3/8"

Gas pipe size 5/8" 5/8" 5/8" 3/4" 3/4" 3/4"

NOTE

If there is any obstacle higher than 2m, or if there is any obstruction at the upper part of the unit, please allow more space

than figure indicated at the above table.

NOTE

Be sure to add the proper amount of additional refrigerant, failure to do so may result in reduced performance.

Remark: The refrigerant pre-charged in the outdoor unit is for the piping length up to 7.5m.

1-11

English

Piping Connection

• Do not use contaminated or damaged copper tubing. If any piping, evaporator or condenser had been exposed or had been

opened for 15 seconds or more, then vacuum and purge with field supplied refrigerant. Generally, do not remove plastic,

rubber plugs and brass nuts from the valves, fittings, tubing and coils until it is ready to connect suction or liquid line into

valves or fittings.

• If any brazing work is required, ensure that nitrogen gas is passed through coil and joints while the brazing work is being

done. This will eliminate soot formation on the inside wall of copper tubings.

• Cut the pipe stages by stages, advancing the blade of pipe cutter slowly. Extra force and a deep cut will cause more

distortion of pipe and therefore extra burr.

• Remove burrs from cut edges of pipes with a remover. Hold the end of the pipe downward to prevent metal chips from

entering the pipe. This will avoid unevenness on the flare face which will cause gas leak.

• Align the center of the piping and sufficiently tighten the flare nut with fingers. Finally, tighten the flare nut with torque

wrench until the wrench clicks.

• Be sure to execute heat insulation. (polyurethane form with thickness more than 15 mm)

• Except the outdoor unit which is pre-charge with refrigerant R22, the indoor unit and the refrigerant connection pipes must

be purged because the air that contain moisture remaining in the refrigerant cycle may cause malfunction to the compressor.

• Insert the flare nuts, mounted on the connection parts of both the indoor unit and outdoor unit onto the copper pipes.

• Flare the pipe with extra length above the flaring tool as shown in the table.

• The flared edge must be even and not cracked or scratched.

Ø Tube, D A (mm)

Inch mm Imperial Rigid

1/4" 6.35 1.3 0.7

3/8" 9.52 1.6 1.0

1/2" 12.70 1.9 1.3

5/8" 15.88 2.2 1.7

3/4" 19.05 2.5 2.0

Cutting Copper Tube

1/4t

Remove Burr

Copper Tube

Swaging Block

Piping Connection To The Units

• Align the center of the piping and tighten the flare nut

sufficiently with fingers.

• Finally, tighten the flare nut with the torque wrench until

the wrench clicks.

Pipe Size mm / (in) Torque Nm / (ft - lb)

6.35 (1/4) 18 (13.3)

9.53 (3/8) 42 (31.0)

12.7 (1/2) 55 (40.6)

15.88 (5/8) 65 (48.0)

19.05 (3/4) 78 (57.6)

Indoor Piping

Flare Nut

Flared Tube

Flare Joint

Spanar

Torque Wrench

1-12

Additional Charge

The refrigerant is pre-charge in the outdoor unit. If the piping length is less than 7.5m, then additional charge after vacuuming

is not necessary. If the piping length is more than 7.5m then use the additional charge value as indicated in the table.

Additional refrigerant charge [g] per additional 1m length as tabulated (for R22 models)

Cooling only

Indoor CK20E CK25E CK28E CK40E CK50E

Outdoor SL20C SL25C SL28C SL35C SL40C (1PH) SL40C (3PH) SL50C

Additional charge [g/m] 38 38 55 56 55 56 55

Example:

CK25E & SL25C with 13m piping length, additional piping length is 5.5m. Thus,

Additional charge = 5.5[m] x 38[g/m]

= 209[g]

Heat Pump Unit

Additional refrigerant charge [g] per additional 1m length as tabulated (for R410A models)

Cooling only

Indoor 5CK20E 5CK25E 5CK28E 5CK40E 5CK50E

Outdoor 5SL20C 5SL25C 5SL28C

5SL35C(1 PH) 5SL35C (3 PH) 5SL40C (1 PH) 5SL40C (3 PH)

5SL50C

Additional charge [g/m] 9 46232727242524

ELECTRICAL WIRING CONNECTION

IMPORTANT: * These values are for information only. They should be checked and selected to comply with local and/or

national codes and regulations. They are also subject to the type of installation and size of conductors.

Cooling Only

COMP

N1

L

N

COMP

N

The electrical power must be provided with

protection devices (circuit breaker or fuse) with

double pole separation system (phase + neutral) with

minimum contact gap of 3.0mm.

(5)CK20/25/28E Vs (5)SL20/25/28C

!

Interconnection

Cable

Indoor Unit

Terminal

Block

Outdoor Unit

Terminal Block

Power Supply Cable

Indoor CK20ER CK25ER CK28ER CK40ER CK50ER

Outdoor SL20CR SL25CR SL28CR SL35CR

SL40CR (1PH) SL40CR (3PH)

SL50CR

Additional charge [g/m] 22 57 58 57 56 56 64

Indoor 5CK20ER 5CK25ER 5CK28ER 5CK40ER 5CK50ER

Outdoor 5SL20CR 5SL25CR 5SL28CR

5SL35CR (1 PH) 5SL35CR (3 PH) 5SL40CR (1 PH) 5SL40CR (3 PH)

5SL50CR

Additional charge [g/m] 16 72 41 43 41 37 37 38

Heat Pump Unit

1-13

English

Model Indoor (5)CK20E (5)CK25E (5)CK28E

Outdoor (5)SL20C (5)SL25C (5)SL28C

Voltage range 220-240V/1Ph/50Hz +

!

Recommended fuse* (A) 13 18 25

Power supply cable size* (mm

2

) 2.5 2.5 4.0

Number of conductors 33 3

Interconnection cable size* (mm

2

) 2.5 2.5 2.5

Number of conductors 33 3

R

N

L

COMP

S

L

COMP

L

N

The electrical power must be provided with

protection devices (circuit breaker or fuse) with

double pole separation system (phase + neutral)

with minimum contact gap of 3.0mm.

(5)CK40E Vs (5)SL35/40C (1 PH)

Indoor Unit

Terminal

Block

Interconnection Cable

Outdoor Unit

Terminal

Block

!

Power Supply Cable

Model Indoor (5)CK40E (5)CK40E

Outdoor (5)SL35C (5)SL40C

Voltage range 220-240V/1Ph/50Hz +

!

Recommended fuse* (A) 25 30

Power supply cable size* (mm

2

) 4.0 4.0

Number of conductors 33

Interconnection cable size* (mm

2

) 2.5 2.5

Number of conductors 44

COMP

L

N

COMP

N

L

R

N

S

T

The electrical power must be provided with

protection devices (circuit breaker or fuse) with

double pole separation system (phase + neutral)

with minimum contact gap of 3.0mm.

(5)CK40/50E Vs (5)SL40/50C (3 PH)

5CK40E Vs 5SL35C

Indoor Unit

Terminal

Block

Interconnection Cable

Outdoor Unit

Terminal

Block

!

Power Supply Cable

1-14

Model Indoor 5CK40E (5)CK40E (5)CK50E

Outdoor 5SL35C (5)SL40R (5)SL50C

Voltage range 380-415V/1Ph/50Hz +

!

Recommended fuse* (A) 10 13 18

Power supply cable size* (mm

2

) 2.5 2.5 2.5

Number of conductors 55 5

Interconnection cable size* (mm

2

) 1.5 1.5 1.5

Number of conductors 44 4

Heat Pump Unit

4WV

OF

N

COMP

4WV

OF

N

COMP

N1

L

The electrical power must be provided with

protection devices (circuit breaker or fuse) with

double pole separation system (phase + neutral)

with minimum contact gap of 3.0mm.

(5)CK20/25/28ER Vs (5)SL20/25/28CR

Indoor Unit

Terminal

Block

Interconnection Cable

Outdoor Unit

Terminal

Block

!

Power Supply Cable

Model Indoor (5)CK20ER (5)CK25ER (5)CK28ER

Outdoor (5)SL20CR (5)SL25CR (5)SL28CR

Voltage range 220-240V/1Ph/50Hz +

!

Recommended fuse* (A) 13 18 18

Power supply cable size* (mm

2

) 2.5 2.5 4.0

Number of conductors 33 3

Interconnection cable size* (mm

2

) 2.5 2.5 2.5

Number of conductors 55 5

Outdoor Coil Sensor

A

4WV

OF

N

L

COMP

A

4WV

OF

COMP

N

L

N

L

The electrical power must be provided with

protection devices (circuit breaker or fuse) with

double pole separation system (phase + neutral)

with minimum contact gap of 3.0mm.

(5)CK40ER Vs (5)SL35/40CR (1 PH)

Indoor Unit

Terminal

Block

Interconnection Cable

Outdoor Unit

Terminal

Block

!

Power Supply Cable

Outdoor Coil Sensor

1-15

English

Model Indoor (5)CK40ER (5)CK40ER

Outdoor (5)SL35CR (5)SL40CR

Voltage range 220-240V/1Ph/50Hz +

!

Recommended fuse* (A) 25 30

Power supply cable size* (mm

2

) 4.0 4

Number of conductors 33

Interconnection cable size* (mm

2

) 2.5 2.5

Number of conductors 3&4 3&4

A

4WV

OF

COMP

A

R

S

T

4WV

OF

N

COMP

N

L

N

L

The electrical power must be provided with

protection devices (circuit breaker or fuse) with

double pole separation system (phase + neutral)

with minimum contact gap of 3.0mm.

(5)CK40/50ER Vs (5)SL40/50CR (3PH)

5CK40ER Vs 5SL35CR (3PH)

Indoor Unit

Terminal

Block

Interconnection

Cable

Outdoor Unit

Terminal

Block

!

Power Supply Cable

380-415V/3Ph/50Hz

Outdoor Coil Sensor

Model Indoor 5CK40ER (5)CK40ER (5)CK50ER

Outdoor 5SL35CR (5)SL40CR (5)SL50CR

Voltage range 380-415V/3Ph/50Hz +

!

Recommended fuse* (A) 10 13 13

Power supply cable size* (mm

2

) 2.5 2.5 2.5

Number of conductors 55 5

Interconnection cable size* (mm

2

) 1.5 1.5 1.5

Number of conductors 3&4 3&4 3&4

1-16

• All wires must be firmly connected.

• Make sure all the wire not touching the refrigerant piping, compressor or any moving parts of the fan motor.

• The connecting wire between the indoor unit and the outdoor unit must be clamped on the wire clamps.

• The power supply cord must be equivalent to H07RN-F (245 IEC65, 245 IEC66) which is the minimum requirement.

• When attaching the terminal box lid, make sure do not pinch any wires.

• After all the wiring connections are done, fill in any gaps/holes with insulation (procured locally) to prevent small animals

and insects entering the unit from outside.

• Use round crimp-style terminal for connecting wires to the power supply terminal block. Connect the wires by matching to

the indication on terminal block. (Refer to the wiring diagram attached on the unit).

Attach insulation sleeve

Round crimp-style terminal

Electric wire

Step to connect the installation wire:

• Used the correct screwdriver for tightening the terminal screws. If the block is too small, the mad of the screw might be

damaged and the screw will not be properly tightened. If tightening too hard, screw might be damaged.

• Do not connect wire at different gauge to the same proper supply terminal.

• Use specified electric wire. Connect the wire securely to the terminal. Lock the wire down without applying excessive

force to the terminal.

• Keep wiring in mat order and not to obstruct other equipment such as popping open the terminal box lid.

Connect wires of the

same gauge to both

side.

Do not connect wires

of the same gauge to

one side.

Do not connect wires

of different gauges.

VACUUMING AND CHARGING

Vacuuming is necessary to eliminate all moisture and air from the system. The series II Outdoor Unit is provided with flare

valve fittings.

Vacuuming for indoor unit

Before vacuuming, perform leak check for refrigeration circuit. After the system piping are properly connected, connect the

flexible hoses to the correct charging nipples as shown in the diagram. Ensure that flexible hose from charging nipples are

connected to the vacuum pump via standard servicing valves and pressure gauges (gauge manifold). Vacuum the air conditioner

system to at least 500 microns Hg. Do not start the unit when the system is engaged in vacuuming. The outdoor is pre-charge.

1-17

English

SPECIAL PRECAUTIONS WHEN CHARGING UNIT

1. Charging procedures – Single phase compressors

Evacuate the system to 500 microns Hg. (67Pa). To reduce evacuation time, use short, large diameter hoses and connect to

unrestricted service ports on the system. Quality of vacuum cannot be determined by time – a reliable vacuum gauge must

be used. (etc. electronic vacuum gauge)

Turn the refrigerant cylinder upside down, purge the charging hose and charge liquid through the liquid line charging port

until refrigerant no longer flows or until the correct charge has been weighed in. If additional charge is required start the

system and slowly bleed liquid into the suction side until the system is full.

Copeland recommends charging liquid in a CONTROLLED manner into the suction side until the system is full.

This recommendation does not hold true for reciprocating compressors where liquid charging into the suction side could

cause severe damage.

Carefully monitor the suction and discharge pressures – ensure that the suction pressure does not fall below 25 psig (1.7

bar) at any time during the charging process.

• Manifold Gauge will show cylinder pressure rather than suction pressure if the cylinder valve and Manifold

valve “A” are both open.

! CAUTION

A

There are many ways of charging liquid in a “controlled manner” into the suction

side:-

1. Use valve A on the manifold gauge set

2. Use the valve on the refrigerant cylinder

3. Charge through a Shredder valve

4. Use a hose with a Shredder valve depressor

5. Charge into the suction side at some distance from the compressor

6. All of the above

2. Charging procedures – Three phase compressors

The fundamental procedure is the same as for single phase models but the compressor can run in the wrong direction on

starting. If this happens reverse any two phases and start again. Short term reverse rotation will not damage the compressor.

All Specter compressors (Model: ZR90 to ZR19M) have internal discharge temperature protectors which are very effective

in preventing dangerously high discharge temperatures during charging. The protection module will trip and lock the

compressor out for 30 minutes. It is not normally necessary to wait 30 minutes for the module to reset. When the compressor

has cooled down the module can be reset by breaking the power supply to the control circuit. Very often the serviceman

does not understand why the module tripped and uses a jumper wire to bypass it. He continues to charge the system and

removes the jumper when charging is complete. The compressor may or may not run with the protector back in the circuit

but it is certain that the compressor has been damaged and premature failure is inevitable.

Short Duct Specification

• The indoor unit is provided with air discharge and air intake “knock-out” hole for duct connection. However the connection

of the short duct for air discharge is possible on only one side.

• The use of short duct for air discharge will improve airflow distribution if there is an obstruction (such as a lighting fixture)

or in a long, narrow room or an L-shaped room. It also use for air conditioning of two rooms simultaneously.

ACCESSORY PARTS

Possible Opening Dimension For Duct Connection

Air Discharge Knock Out Hole

Air Intake

Knock Out Hole

Possible Direction For Air Discharge And Air Intake

Air Intake

Air DischargeAir Discharge

Air Discharge Air Discharge

10

50 50 50 50 50 10

207020

90

Ø100

PCD Ø140

115 20 115

1-18

NOTE

• Avoid using the short duct on which the air discharge grille can be completely closed, to prevent evaporator freezing.

• In order to prevent condensation forming, be sure that there is sufficient thermal insulation and no leakage of cool

air when installing the short duct.

• Keep the introduction of fresh air intake within 20% of total air flow. Also provide a chamber and use a booster fan.

Sealing Material

• It is possible to seal one of the four air discharge outlet. (sealing two or more air discharge outlet could cause a malfunction)

• Remove the front panel and insert the sealing material into the air discharge outlet on the indoor unit to seal the air outlet.

• The sealing material is the same length as the longer air discharge outlet. If it is desired to seal the shorter air discharge

outlet, cut the sealing material to shorten it.

• Push the sealing material in about 10 mm beyond the bottom surface of the indoor unit so that it does not touch the air

louver. Be sure not to push the sealing material in any farther than about 10mm.

INDICATOR LIGHTS

Remote Control

When there is infrared remote control operating signal, the signal receiver on indoor unit will made a <beep> for signal

acceptance confirmation.

NOTE

CDF LED = Cool/Dry/Fan LED, turns on in these modes

The unit will not detect sensor missing when the compressor is ON

Call your dealer immediately when this error happen

OVERALL CHECKING

• After installation of the unit, ensure that :-

1. The unit has been mounted solidly and rigid in position.

2. Outdoor unit is fully installed

3. Gas leak test is been checked.

4. Unit is fully insulated.

5. The drainage is flow smoothly - pour some water into the main drain pipe from the flexible drain hose.

6. The power supply, voltage correspond to that unit shown on wiring diagram are attached on the unit.

7. Wiring and piping install correctly and firmly.

8. Unit is safely grounded.

9. Wiring size is according to specification.

10. Air inlet and outlet are not blocked.

11. Note down the refrigerant piping length and additional refrigerant charge.

• Test run

1. Conduct a test run after water drainage test and gas leakage test.

2. Check the following items :-

a. Is the electric plug firmly inserted into the socket ?

b. Is there any abnormal sound from the unit ?

c. Is there any abnormal vibration on the unit itself or piping ?

d. Is the drainage of water smooth ?

• Confirm that :

1. Condenser fan is running, with warm air blowing off the condensing unit.

2. Evaporator blower is running and discharge cool air.

3. The remote control incorporate a 3 minute delay in the circuit. Thus, it requires about 3 minutes before the outdoor

condensing unit can start up.

Event CDF LED Timer LED Other LEDs

1. Room Sensor Open or Short Blink 1 time - Blink Fan

2. Indoor Coil Sensor Open Blink 2 times - Blink Sleep

3. Outdoor Coil Sensor Open Blink 3 times - Blink Dry

Compressor Overload /

4. Indoor Coil Sensor Short / - Blink 1 time Blink Cool

Outdoor Coil Sensor Short

5. Gas Leak - Blink 3 times Blink Cool & Dry

6. Water Pump Fault - Blink 2 times Blink Cool & Fan

7. Outdoor Defrost - - Blink Heat

8. Outdoor Coil Sensor Exist (MS model) - Blink 5 times Blink Cool & Heat

9. Hardware Error (tact switch pin short) - Blink 6 times Blink Heat, Cool, follow by Fan, Dry

La page charge ...

Acson E Series Guide d'installation

Acson E Series Guide d'installation

dans d''autres langues

Documents connexes

Autres documents