Faber Cylindra 15 SS 600 Manuel utilisateur

CYLN15SS600

Installation Instructions

Use and Care Information

Instructions d'installation

Utilisez et d'entretien

Instrucciones de instalación

Información de uso y cuidado

CYLINDRA

2

CONTENTS

Section Page

IMPORTANT SAFETY INSTRUCTIONS 3

RANGE HOOD DIMENSIONS 6

INSTALLATION HEIGHT REQUIREMENTS 7

PARTS 8

TOOLS NEEDED 10

VENTING METHOD 11

PREPARING TO MOUNT THE RANGE HOOD 13

INSTALLING WALL SUPPORT 18

CHOOSING VENTING METHOD 19

ATTACH VENTING: OPTION 1 - REAR DUCTING 20

ATTACH VENTING: OPTION 2 - TOP VENTING

24

ATTACH VENTING: OPTION 3 - NON DUCTED RECIRCULATING

26

COMFORT PANEL INSTALLATION

29

CONNECTING HOUSE POWER

30

HOOD ELECTRICAL CONNECTIONS

31

OPERATING THE CONTROLS

32

REMOTE CONTROL (OPTIONAL)

33

CLEANING STAINLESS STEEL

33

CARING FOR FILTERS

34

REPLACING BULBS

35

WARRANTY

36

3

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS BEFORE YOU START

INSTALLING THIS Range Hood

WARNING: - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

a) Never leave surface units unattended at high settings. Boilovers cause smoking and

greasy spillovers that may ignite. Heat oils slowly on low or medium setting.

b)AlwaysturnhoodONwhencookingathighheatorwhenambeingfood(i.e.Crepes

Suzette, Cherries Jubilee, Peppercorn Beef Flambé).

c) Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or

lter.

d) Use proper pan size. Always use cookware appropriate for the size of the surface element.

WARNING: - TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE

TOP GREASE FIRE, OBSERVE THE FOLLOWING*:

a)SMOTHERFLAMESwithaclose-ttinglid,cookiesheet,ormetaltray,thenturnoffthe

burner.BECAREFULTOPREVENTBURNS.Iftheamesdonotgooutimmediately

EVACUATE AND CALL THE FIRE DEPARTMENT.

b) NEVER PICK UP A FLAMING PAN - You may be burned.

c) DO NOT USE WATER, including wet dishcloths or towels - a violent steam explosion will

result.

d) Use an extinguisher ONLY if:

1. You know you have a Class ABC extinguisher, and you already know how to operate

it.

2. Thereissmallandcontainedintheareawhereitstarted.

3. Theredepartmentisbeingcalled.

4. Youcanghttherewithyourbacktoanexit.

* Based on "Kitchen Firesafety Tips" published by NFPA

WARNING - TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, do not use this fan with

any solid-state speed control device.

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer. If you have any questions,

contact the manufacturer.

2. Before servicing or cleaning unit, switch power off at service panel and lock the service

disconnecting means to prevent power from being switched on accidentally. When the

service disconnecting means cannot be locked, securely fasten a prominent warning

device, such as a tag, to the service panel.

CAUTION: For General Ventilating Use Only. Do Not Use To Exhaust Hazardous or Explo-

sive Materials and Vapors.

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

1. InstallationWorkAndElectricalWiringMustBeDoneByQualiedPerson(s)InAccor-

dance With All Applicable Codes And Standards, Including Fire-Rated Construction.

2. Sufcientairisneededforpropercombustionandexhaustingofgasesthroughthe

ue(chimney)offuelburningequipmenttopreventbackdrafting.Followtheheating

equipment manufacturer's guideline and safety standards such as those published by

the National Fire Protection Association (NFPA), and the American Society for Heating,

Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.

4

ALL WALL AND FLOOR OPENINGS WHERE THE Range Hood IS INSTALLED

MUST BE SEALED.

This Range Hood requires at least 24" of clearance between the bottom of the Range

Hood and the cooking surface or countertop. This hood has been approved by UL at this

distance from the cooktop.

This minimum clearance may be higher depending on local building codes. For gas cooktops

and combination ranges, a minimum of 30" is recommended and may be required.

Overhead cabinets on both sides of this unit must be a minimum of 18" above the cooking

surface or countertop. Consult the cooktop or range installation instructions given by the

manufacturer before making any cutouts.

MOBILE HOME INSTALLATION The installation of this Range Hood must conform to the

Manufactured Home Construction and Safety Standards, Title 24 CFR, Part 3280 (formerly

Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, Part 280). See

Electrical Requirements"

• Venting system MUST terminate outside the home.

• DO NOT terminate the ductwork in an attic or other enclosed space.

• DO NOT use 4" laundry-type wall caps.

• Flexible-type ductwork is not recommended.

• DO NOT obstruct the ow of combustion and ventilation air.

• Failure to follow venting requirements may result in a re.

WARNING

!

VENTING REQUIREMENTS

Determine which venting method is best for your application. Ductwork can extend either

through the wall or the roof.

The length of the ductwork and the number of elbows should be kept to a minimum to

provide efcient performance. The size of the ductwork should be uniform. Do not install

two elbows together. Use duct tape to seal all joints in the ductwork system. Use caulking

to seal exterior wall or oor opening around the cap.

Flexible ductwork is not recommended. Flexible ductwork creates back pressure and air

turbulence that greatly reduces performance.

Make sure there is proper clearance within the wall or oor for exhaust duct before making

cutouts. Do not cut a joist or stud unless absolutely necessary. If a joist or stud must be cut,

then a supporting frame must be constructed.

WARNING - To Reduce The Risk Of Fire, Use Only Metal Ductwork.

CAUTION-Toreduceriskofreandtoproperlyexhaustair,besuretoductairoutside

– Do not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces,

or garages.

Cold Weather installations

An additional back draft damper should be installed to minimize backward cold air ow and a nonme-

tallic thermal break should be installed to minimize conduction of outside temperatures as part of the

vent system. The damper should be on the cold air side of the thermal break. The break should be as

close as possible to where the vent system enters the heated portion of the house.

3. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other

hidden utilities.

4. Ducted fans must always be vented to the outdoors.

5

ELECTRICAL REQUIREMENTS

A 120 volt, 60 Hz AC-only electrical supply is required on a separate 15 amp fused circuit.

A time-delay fuse or circuit breaker is recommended. The fuse must be sized per local

codes in accordance with the electrical rating of this unit as specied on the serial/rating

plate located inside the unit near the eld wiring compartment.

ELECTRICAL INSTALLATION WITH WIRING BOX

THIS UNIT MUST BE CONNECTED WITH COPPER WIRE ONLY. Wire sizes must conform

to the requirements of the National Electrical Code, ANSI/NFPA 70 - latest edition, and all

local codes and ordinances. Wire size and connections must conform with the rating of

the appliance. Copies of the standard listed above may be obtained from:

National Fire Protection Association

Batterymarch Park

Quincy, Massachusetts 02269

This appliance should be connected directly to the fused disconnect (or circuit breaker)

through exible, armored or nonmetallic sheathed copper cable. Allow some slack in

the cable so the appliance can be moved if servicing is ever necessary. A UL Listed,

1/2" conduit connector must be provided at each end of the power supply cable (at

the appliance and at the junction box).

When making the electrical connection, cut a 1 1/4" hole in the wall. A hole cut through

wood must be sanded until smooth. A hole through metal must have a grommet.

• Electrical ground is required on this Range Hood.

• If cold water pipe is interrupted by plastic, nonmetallic gaskets or other

materials, DO NOT use for grounding.

• DO NOT ground to a gas pipe.

• DO NOT have a fuse in the neutral or grounding circuit. A fuse in the neutral

or grounding circuit could result in electrical shock.

• Check with a qualied electrician if you are in doubt as to whether the Range

Hood is properly grounded.

• Failure to follow electrical requirements may result in a re.

WARNING

!

State of California Proposition 65 Warning (US only)

WARNING

This product contains chemicals known to the State of California to cause cancer

and birth defects or other reproductive harm.

For more information go to www.P65Warnings.ca.gov

6

RANGE HOOD DIMENSIONS

PERSONAL INJURY HAZARD

Because of the weight and size of the Range Hood canopy, two or more people are needed

to move and safely install the Range Hood canopy.

Failure to properly lift Range Hood could result in damage to the product or personal injury.

WARNING

!

Version 07/11- Page 5

PRODUCT DIMENSIONS

14 9/16”

35 1/16”

13 3/4”

21 1/4”

17 1/8”

4 7/16”

9 13/16”

6 11/16”

5”

6 1/8”

5 3/4”

6 7/8”

27 3/16”

6 7/8”

18 5/16” 15 3/8”

21 1/4”13 3/4”

35 1/16”

9 13/16”

5 3/4”

17 1/8”

4 7/16”

7 7/8”

6 11/16”

14 9/16”

9 7/8”

17 1/8”

9 13/16”

14 9/16”

6 1/8”

5 1/16”

FRONT

SIDE

TOP

BACK

OVERALL

NOTE: The installation diagram in FIGURE 4 on the next page is used for the recommended installation height

of 24" off the cooktop. For maximum installation heights of up to 30" off the cooktop, add onto the horizontal

line of 42 5/16" in FIGURE 4. For example add 6", or 48 5/16" total, to install 30" off the cooktop.

NOTE: For 8" ceilings, the Cylindra should be installed at 24" off the cooktop and the hood is mounted at the

ceiling. For higher ceilings, the Cylindra is mounted at 24 - 30" off the cooktop and is installed "ﬂoating" in

the middle of the wall, not at the ceiling.

BACK SIDE

TOP

FRONT

OVERALL

7

INSTALLATION HEIGHT REQUIREMENTS

MIN. 24" OVER ELECTRIC

MIN. 30" OVER GAS

NOTE: the installation diagram on page 14 is used for the recommended installation height

of 24" off the cooktop. For maximum installation heights of up to 30" off the cooktop, add

onto the horizontal line of 42 5/16" on page 14. For example add 6", or 48 5/16" total, to

install 30" off the cooktop.

NOTE: for 8" ceilings, the cylindra should be installed at 24" off the cooktop and the hood

is mounted at the ceiling. For higher ceilings, the cylindra is mounted at 24 - 30" off the

cooktopandisinstalled"oating"inthemiddleofthewall,notattheceiling.

Min.24” Min.30”

8

PARTS

REF. PART

QTY

A

Hood body

1

B

Damper

1

C

PVC ductless pipe

1

D

Ductless Grille

1

F

Motor and Support

1

M

Support Range Hood

1

REF

PART

G

Pozi Screws (1/8" x 3/8")

2

H

Pozi Screws (3/16" x 1/2")

4

I

Torx Screws (1/4" x 2 3/4")

4

L

Screws plug

4

PARTS INCLUDED

9

B

A

F

M

C

D

10

PARTS NEEDED

PARTS (cont.)

PART

6" Round Metal Ductwork

Wire connectors.

Drywall plugs or other suitable wall fasteners based on your

installation.

TOOLS NEEDED

TOOL

Tape Measure

Pencil

Electric Drill with 5/16" Drill Bit

Phillips Screwdriver

Torx Screwdriver

Metal sheers

Work gloves

Foil tape

ACCESSORIES AVAILABLE

ACCESSORY

SKU#

Replacement Activated Charcoal Filter

#FILTER2

Wireless Remote Control

#REMCTRL2

CFM Reducer Kit

CFMRED2

11

VENTING METHOD

Option 1: REAR VENTED

Option 2: TOP VENTED

Option 3: RECIRCULATING

Rear

ø 120 mm

ø 150 mm

2x

ø 150 mm

2x

W

550 mm550 mm

7"

1

Requires purchase of

Activated Charcoal

Accessory kit.

ø 120 mm

ø 150 mm

2x

ø 150 mm

2x

W

550 mm550 mm

7"

Top

ø 120 mm

ø 150 mm

2x

ø 150 mm

2x

W

550 mm550 mm

12

PREPARATION FOR REAR DUCTING ONLY.

Use metal sheers to cut the pre-scored hole in the Range Hood Support

M

.

2

13

PREPARING TO MOUNT THE RANGE HOOD

DRAW POSITIONING LINES

Draw a vertical line

H

on the supporting wall to the ceiling or

upper limit, at the center of the area in which the hood will be

installed.

Draw a horizontal line

I

where the bottom edge of the hood will

be located, a minimum of 24" above an electric cooking surface

and 30" above a gas cooking surface.

3

MIN. 24" OVER ELECTRIC/MIN. 30" OVER GAS

I

H

14

1. Disconnect and move freestanding range from cabinet opening

to provide easier access to rear wall. Put a thick, protective

covering over cooktop, set-in range or countertop to protect

from damage or dirt.

2. Draw a Horizontal line at a minimum of 41 5/16" above the

Cooktop.

3. Mark 2 holes at 3 15/16" to the right and left of this line.

Check that the two marks are level, before drilling.

4. Mark a reference point at 15 3/8" above the 41 5/16" line and

mark 2 holes 3 15/16" to the right and left of this line.

Check that the two marks are level, before drilling.

4

NOTE:The grey part is only for rear venting method.

30" 24"

15

NOTE: When installing the hood in the ductless version, leave at least 4"

between the top of the hood and the ceiling for proper air circulation.

Ø 3 15/16”

5. Drill 2 holes at 3 15/16" to the right and left of this line.

6. Drilling the 2 holes at 15 3/8" above the 41 5/16" line to the right

and left of this line.

16

1 15/16”

6 13/16”

7. Verify the Power Supply Cable location using the Hood Range

Hood Support

M

and by matching up the corner wall mounting

holes. Drill the hole in the wall for the Power Supply Cable

F

M

8. Place the Motor and Wall Support

F

into the Range Hood

Support

M

.Line up the holes..

17

1 15/16”

6 13/16”

10. Break the correct hole in the Wiring Box for passing the Power

Supply Cable.

F

M

9. Verify the hole in the wall for the Power Supply Cable with the

hole in the wall support

F

and with the hole in the support

Range Hood

M

.

18

I

Torx Screws (1/4" x 2 3/4")

I

5

INSTALLING WALL SUPPORT

1. Attach the motor and wall support

F

with support range hood

M

using the 4 wall support screws

I

.

2. Level the motor and wall support

F

before permanently

attaching.

F

M

Torx Screwdriver

19

CHOOSING VENTING METHOD

Option 1: REAR VENTED

Option 2: TOP VENTED

Option 3: RECIRCULATING

Rear

ø 120 mm

ø 150 mm

2x

ø 150 mm

2x

W

550 mm550 mm

7"

ø 120 mm

ø 150 mm

2x

ø 150 mm

2x

W

550 mm550 mm

7"

Top

ø 120 mm

ø 150 mm

2x

ø 150 mm

2x

W

550 mm550 mm

Go to Pg.20

Go to Pg.24

Go to Pg.26

20

REAR VENTED:

1. A 90° elbow (purchased separately) is

necessary for connecting the hood to

the venting through the 7 1/2" x 6 5/16"

wide opening to the back wall.

6

ATTACH VENTING: OPTION 1 - REAR DUCTING

Rear

ø 120 mm

ø 150 mm

2x

ø 150 mm

2x

W

550 mm550 mm

3 15/16” 3 15/16”

15 3/8”

41 5/16”

7 15/16” 7 1/2”

6 5/16”

La page charge ...

Faber Cylindra 15 SS 600 Manuel utilisateur

Ce manuel convient également à

Faber Cylindra 15 SS 600 Manuel utilisateur

dans d''autres langues

Documents connexes