Faber Levante G 30 SS 300 cfm Le manuel du propriétaire

LEVG24SS300

LEVG30SS300

Installation Instructions

Use and Care Information

Instructions d'installation

Utilisez et d'entretien

Instrucciones de instalación

Información de uso y cuidado

LEVANTE G

2

CONTENTS

Section Page

Important safety instructions 3

Range hood dimensions 6

Installation height requirements 7

Parts 8

Tools needed 9

Before installation remove shipping materials 10

Only for Canadian market 11

Choose vertical or horizontal electrical connection knockout'sChoose vertical or horizontal electrical connection knockout's 12

Venting method options-ducted or ductless 14

Non ducted recirculation option 15

Ducted - 7" round outlet 16

Ducted - 3 1/4" x 10" rectangular outlet on top

18

Ducted - 3 1/4" x 10" rectangular outlet rear

19

Choosing the mounting method

20

Mounting range hood on wall

21

Mounting range hood under the cabinet

25

Connecting electricity

27

Operating the controls

28

Caring for lters

29

Replacing lighting

31

Wiring diagram

32

Warranty

33

3

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS BEFORE YOU START

INSTALLING THIS RANGE HOOD

WARNING: - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

a) Never leave surface units unattended at high settings. Boilovers cause smoking and

greasy spillovers that may ignite. Heat oils slowly on low or medium setting.

b) Always turn hood ON when cooking at high heat or when ambeing food (i.e. Crepes

Suzette, Cherries Jubilee, Peppercorn Beef Flambé).

c) Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or

lter.

d) Use proper pan size. Always use cookware appropriate for the size of the surface element.

WARNING: - TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE

TOP GREASE FIRE, OBSERVE THE FOLLOWING*:

a) SMOTHER FLAMES with a close-tting lid, cookie sheet, or metal tray, then turn off the

burner. BE CAREFUL TO PREVENT BURNS. If the ames do not go out immediately

EVACUATE AND CALL THE FIRE DEPARTMENT.

b) NEVER PICK UP A FLAMING PAN - You may be burned.

c) DO NOT USE WATER, including wet dishcloths or towels - a violent steam explosion will

result.

d) Use an extinguisher ONLY if:

1. You know you have a Class ABC extinguisher, and you already know how to operate

it.

2. The re is small and contained in the area where it started.

3. The re department is being called.

4. You can ght the re with your back to an exit.

* Based on "Kitchen Firesafety Tips" published by NFPA

WARNING - TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, do not use this fan with

any solid-state speed control device.

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer. If you have any questions,

contact the manufacturer.

2. Before servicing or cleaning unit, switch power off at service panel and lock the service

disconnecting means to prevent power from being switched on accidentally. When the

service disconnecting means cannot be locked, securely fasten a prominent warning

device, such as a tag, to the service panel.

CAUTION: For General Ventilating Use Only. Do Not Use To Exhaust Hazardous or Explo-

sive Materials and Vapors.

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

1. Installation Work And Electrical Wiring Must Be Done By Qualied Person(s) In Accor-

dance With All Applicable Codes And Standards, Including Fire-Rated Construction.

2. Sufcient air is needed for proper combustion and exhausting of gases through the

ue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating

equipment manufacturer's guideline and safety standards such as those published by

the National Fire Protection Association (NFPA), and the American Society for Heating,

Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.

4

ALL WALL AND FLOOR OPENINGS WHERE THE RANGE HOOD IS INSTALLED

MUST BE SEALED.

This Range Hood requires at least 24" of clearance between the bottom of the Range

Hood and the cooking surface or countertop. This hood has been approved by UL at this

distance from the cooktop.

This minimum clearance may be higher depending on local building codes. For gas cooktops

and combination ranges, a minimum of 30" is recommended and may be required.

Overhead cabinets on both sides of this unit must be a minimum of 18" above the cooking

surface or countertop. Consult the cooktop or range installation instructions given by the

manufacturer before making any cutouts.

MOBILE HOME INSTALLATION The installation of this Range Hood must conform to the

Manufactured Home Construction and Safety Standards, Title 24 CFR, Part 3280 (formerly

Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, Part 280). See

Electrical Requirements"

• Venting system MUST terminate outside the home.

• DO NOT terminate the ductwork in an attic or other enclosed space.

• DO NOT use 4" laundry-type wall caps.

• Flexible-type ductwork is not recommended.

• DO NOT obstruct the ow of combustion and ventilation air.

• Failure to follow venting requirements may result in a re.

WARNING

!

VENTING REQUIREMENTS

Determine which venting method is best for your application. Ductwork can extend either

through the wall or the roof.

The length of the ductwork and the number of elbows should be kept to a minimum to

provide efcient performance. The size of the ductwork should be uniform. Do not install

two elbows together. Use duct tape to seal all joints in the ductwork system. Use caulking

to seal exterior wall or oor opening around the cap.

Flexible ductwork is not recommended. Flexible ductwork creates back pressure and air

turbulence that greatly reduces performance.

Make sure there is proper clearance within the wall or oor for exhaust duct before making

cutouts. Do not cut a joist or stud unless absolutely necessary. If a joist or stud must be cut,

then a supporting frame must be constructed.

WARNING - To Reduce The Risk Of Fire, Use Only Metal Ductwork.

CAUTION - To reduce risk of re and to properly exhaust air, be sure to duct air outside

– Do not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces,

or garages.

Cold Weather installations

An additional back draft damper should be installed to minimize backward cold air ow and a nonme-

tallic thermal break should be installed to minimize conduction of outside temperatures as part of the

vent system. The damper should be on the cold air side of the thermal break. The break should be as

close as possible to where the vent system enters the heated portion of the house.

3. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other

hidden utilities.

4. Ducted fans must always be vented to the outdoors.

5

ELECTRICAL REQUIREMENTS

A 120 volt, 60 Hz AC-only electrical supply is required on a separate 15 amp fused circuit.

A time-delay fuse or circuit breaker is recommended. The fuse must be sized per local

codes in accordance with the electrical rating of this unit as specied on the serial/rating

plate located inside the unit near the eld wiring compartment.

ELECTRICAL INSTALLATION WITH WIRING BOX

THIS UNIT MUST BE CONNECTED WITH COPPER WIRE ONLY. Wire sizes must conform

to the requirements of the National Electrical Code, ANSI/NFPA 70 - latest edition, and all

local codes and ordinances. Wire size and connections must conform with the rating of

the appliance. Copies of the standard listed above may be obtained from:

National Fire Protection Association

Batterymarch Park

Quincy, Massachusetts 02269

This appliance should be connected directly to the fused disconnect (or circuit breaker)

through exible, armored or nonmetallic sheathed copper cable. Allow some slack in

the cable so the appliance can be moved if servicing is ever necessary. A UL Listed,

1/2" conduit connector must be provided at each end of the power supply cable (at

the appliance and at the junction box).

When making the electrical connection, cut a 1 1/4" hole in the wall. A hole cut through

wood must be sanded until smooth. A hole through metal must have a grommet.

• Electrical ground is required on this Range Hood.

• If cold water pipe is interrupted by plastic, nonmetallic gaskets or other

materials, DO NOT use for grounding.

• DO NOT ground to a gas pipe.

• DO NOT have a fuse in the neutral or grounding circuit. A fuse in the neutral

or grounding circuit could result in electrical shock.

• Check with a qualied electrician if you are in doubt as to whether the Range

Hood is properly grounded.

• Failure to follow electrical requirements may result in a re.

WARNING

!

State of California Proposition 65 Warning (US only)

WARNING

This product contains chemicals known to the State of California to cause cancer

and birth defects or other reproductive harm.

For more information go to www.P65Warnings.ca.gov

6

RANGE HOOD DIMENSIONS

7 1/4

3

23 15/16” - 29 15/16” - 35 15/16”

7

1/4

3

23 15/16” - 29 15/16” - 35 15/16”

24" 30"

24"

30"

DRAFT 07-JUL-2020 06:22

7

MIN. 24" OVER ELECTRIC / MIN. 30" OVER GAS

INSTALLATION HEIGHT REQUIREMENTS

Min. 24" - 30"

8

PARTS

REF. PART

A

Hood body – Includes Controls, Light, Filters, Blower 1

B

Damper (3 1/4" x 10") 1

C

7" Round Flange 1

D

Grid (Only for Canadian Market) 1

REF

PART

E

Pozi Screws (3/16" x 1 15/16")

4

F

Torx Screws (1/8" x 3/8")

4

PARTS INCLUDED

C

B

A

D

Available Accessories

Activated Charcoal Filter (FILTER5)

Note: The Charcoal Filter is attached with two screws

(See page 15 and Figure C).

The Charcoal Filters must be purchased with only Faber

authorized dealers.

9

PARTS NEEDED

PARTS (cont.)

PART

7" Round Metal Ductwork

3 1/4" x 10" Rectangular Ductwork

7" Damper

Wire connectors.

Power Supply Cable.

-

Drywall plugs or other suitable wall fasteners based on

your installation.

Wall Cap/Roof Cap Needs to be purchased separately

TOOLS NEEDED

TOOL

Tape Measure

Pencil

Electric Drill with 5/16" Drill Bit

Phillips Screwdriver

Torx Screwdriver

Pozi Screwdriver

10

BEFORE INSTALLATION REMOVE SHIPPING

MATERIALS

Remove the side packaging.

Remove the foam packaging and wood bar.

1

2

3

Ready for Installation.

Caution: Do not

pick up hood using

the wood bar

11

ONLY FOR CANADIAN MARKET

1

2

For ducted installations only:

Remove the lters one at a time by pushing towards the back of the hood and

pulling down at the same time.

Install the screws as pictured.

Install Grid

D

with the two screws removed from step 2. Screw the protection

grid into the location shown in the picture below. (The correct location has a

rectangular cut out to accommodate the grid.)

Take care to screw the grid completely ush to avoid unwanted noise.

Remove the screws as pictured.

Remove two of the screws from the motor assembly housing as pictured.

3

Phillips Screwdriver

D

12

Remove the lters one at

a time by pushing them

towards the back of the

hood and pulling down at

the same time.

Remove the wiring box

cover by unscrewing

the 2 screws.

Preparing the hood for electrical knockouts

7" 1/2

13/16"

Created by

Palazzi, Walter

Denomination

GENERAL ASSEMBLY

Lang EN

Sheet

3

/3

Modif.by

Astolfi, Ilaria

Approved by

Approval date

Doc. status

Drawing N.

02B_710

Rev

01

CHOOSE VERTICAL OR HORIZONTAL

ELECTRICAL CONNECTION KNOCKOUT'S

1

2

Phillips Screwdriver

13

Rear Hole (Horizontal)

Choose the rear hole for the electric connection and break with a screwdriver or other

tool.

During the installation thread Power Supply Cable through this hole.

3

Top Hole (Vertical)

Choose the top hole for the electric connection and break with a screwdriver or

other tool.

During the installation thread Power Supply Cable through this hole.

4

14

VENTING METHOD OPTIONS-DUCTED OR

DUCTLESS

DUCTED WITH 7" ROUND OUTLET:

– Vertical

– Horizontal

7"

Rear

Top

10"

3 1/4"

10"

3 1/4"

Rear

Top

Go to page 16Go to page 15

Go to page 18

DUCTED WITH 3 1/4" X 10" RECTANGULAR OUTLET

– Vertical

– Horizontal

NON DUCTED - RECIRCULATION

OPTION

Requires

purchase

of

Activated

Charcoal

Accessory

15

b1

a

b2

Remove the indicated blower cover

(do not discard the screw).

Reinstall the existing Grease Filters

after installing the Activated Charcoal

Filter before operating hood.

Reinstall the modied blower cover

with the same screw.

Cut the

cover

where

indicated in

picture b1.

Discard /

Recycle

upper

pieces of

blower

cover.

d

b3

NON DUCTED RECIRCULATION OPTION

Go to page 20

Required Activated Charcoal

Filter Accessory - (FILTER5)

purchased separately.

c

Non Ducted installations only:

1. Remove the two screws located on the motor

housing in the location indicated.

2. Place the charcoal lter with the tabs against

the blower housing in the location indicated on

gure

c

. The front side of the FILTER5 will

have the keyhole mounting on the top surface

of the lter. A layer of charcoal will be visible

through the grills.

3. Use the two screws removed earlier to attach

the FILTER5 in place.

NOTE: For Non ducted installations the Canadian

Grid should NOT be used.

16

DUCTED - 7" ROUND OUTLET

Cut where indicated.

Remove both the rectangular and semicircle areas with metal shears.

Rear

Top

7"

Required; 7" Round

Damper purchase

separately.

1

Caution: If an elbow

is required, do it

as far away from

the hood's exhaust

opening as possible.

17

Install the Flange with Flange transition screws

F

.

Install 7" Round Damper purchased separately. Secure damper with foil duct tape.

Connect the 7" Round Metal Ductwork to the Roof or Wall Cap purchased separately

and then attach ductwork.

2

3

Torx Screwdriver

NOTE: The Flange must be mounted with the lip facing upward.

Only use the screws provided for the ange

F

Torx Screws (1/8" x 3/8")

4

Go to page 20

18

Choose the rectangular upper air outlet or rectangular rear air outlet and cut where

indicated.(See page 19 for Rear Outlet)

Install the included rectangular air outlet with two screws

F

.

Connect the metal ductwork to the Roof or Wall Cap purchased separately and

then attach ductwork.

Rear

Top

3 1/4" x 10"

DUCTED - 3 1/4" X 10" RECTANGULAR OUTLET

ON TOP

1

2

3

Torx Screwdriver

F

Torx Screws (1/8" x 3/8")

Caution: If an elbow is required,

do it as far away from the

hood's exhaust opening as

possible.

19

Go to page 20

Rear

3 1/4" x 10"

Use the rear air outlet and cut where indicated.

Install the included rectangular air outlet with two screws

F

.

1

2

Torx Screwdriver

F

Torx Screws (1/8" x 3/8")

DUCTED - 3 1/4" X 10" RECTANGULAR OUTLET

REAR

Caution: If an elbow is required,

do it as far away from the

hood's exhaust opening as

possible.

Connect the metal ductwork to the Roof or Wall Cap purchased separately and

then attach ductwork.

3

20

CHOOSING THE MOUNTING METHOD

Installation for Mounting on the Wall

Installation for Mounting to the cabinet

Page

21

Page

25

La page charge ...

Faber Levante G 30 SS 300 cfm Le manuel du propriétaire

Ce manuel convient également à

Faber Levante G 30 SS 300 cfm Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents