Shop Vac 92LSQ650 Manuel utilisateur

Marque: Shop Vac

Modèle: 92LSQ650

Catégorie: Aspirateurs

Taper: Manuel utilisateur

Ce manuel convient également à

92MSQ650

USER MANUAL

Series:

87MT

92M

92L

ATTENTION!

DANGER!

Read all safety rules carefully before attempting to operate. Retain for

future reference.

Never operate this unit when ﬂammable materials or

vapors are present because electrical devices produce

arcs or sparks that can cause a ﬁre or explosion. NEVER

OPERATE UNATTENDED!

For your records, please record the following information

and store this user manual in a safe location.

Catalog No.

Model No.

Purchase Date:

(Located on the carton)

(Located on top portion of the vacuum)

87557-84

Commercial/Industrial use

WET/DRY VACUUM

TABLE OF CONTENTS

Important Safety Instructions .............................................................................................

Grounding Instructions ....................................................................................................

Extension Cords .................................................................................................................

Unpacking .........................................................................................................................

Assembly ........................................................................................................................

Set Up and Operation .........................................................................................................

Filter Installation and Maintenance ................................................................................

Blower Feature ................................................................................................................

Empty Liquid Waste From the Tank ..................................................................................

Automatic Suction Shut Off ..............................................................................................

Lubrication ......................................................................................................................

Storage ............................................................................................................................

Service ............................................................................................................................

Troubleshooting ...............................................................................................................

Warranty and Contact Information ....................................................................................

3-4

5-7

8-10

SECTION PAGES

TOOLS NEEDED

PAGE 2

• Safety Glasses

•

/8”,

/16”, (2)

/16” and (2)

/2”

Wrench or socket (not needed

with all vacuums)

• Flathead Screwdriver

IMPORTANT SAFETY INSTRUCTIONS

When using an electric appliance, basic precautions should always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE.

WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY:

1. Do not leave appliance when plugged in. Unplug from outlet when not in use and before servicing.

Connect to a properly grounded outlet only. See Grounding Instructions.

2. Do not expose to rain – store indoors.

3. Do not allow to be used as a toy. Close attention is necessary when used by or near children.

4. Use only as described in this manual. Use only Manufacturer’s recommended attachments.

5. Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped,

damaged, left outdoors or dropped into water, contact Shop-Vac Corporation for assistance.

6. Do Not: pull or carry by cord, use cord as a handle, close a door on cord or pull cord around sharp edges

or corners. Do not run appliance over cord. Keep cord away from heated surfaces.

7. Do not unplug by pulling on cord. To unplug, grasp the plug; not the cord.

8. Do not handle plug or appliance with wet hands.

9. Do not put any object into openings. Do not use with any openings blocked; keep free of dust, lint, hair

and anything that may reduce air ﬂow.

10. Keep hair, loose clothing, ﬁngers and all parts of body away from openings and moving parts.

11. Do not pick up anything that is burning or smoking, such as cigarettes, matches or hot ashes.

12. Do not use without dust bag and/or ﬁlters in place.

13. Turn off all controls before unplugging.

14. Use extra care when cleaning on stairs.

15. Do not use to pick up ﬂammable or combustible liquids such as gasoline or use in areas where they

may be present.

16. Do not use your cleaner as a sprayer of ﬂammable liquids such as oil base paints, lacquers, household

cleaners, etc.

17. Do not vacuum toxic, carcinogenic, combustible or other hazardous materials such as asbestos, arsenic,

barium, beryllium, lead, pesticides or other health endangering materials. Specially designed units are

available for these purposes.

18. Do not pick up soot, cement, plaster or drywall dust without cartridge ﬁlter and collection ﬁlter bag in

place. These are very ﬁne particles that may pass through the foam and affect the performance of the

motor or be exhausted back into the air. Additional collection ﬁlter bags are available.

19. Do not leave the cord lying on the ﬂoor once you have ﬁnished the cleaning job. It can become a tripping

hazard.

20. Use special care when emptying heavily loaded tanks.

21. To avoid spontaneous combustion, empty tank after each use.

22. The operation of a utility vac can result in foreign objects being blown into eyes, which can result in eye

damage. Always wear safety goggles when operating vacuum.

23. STAY ALERT. Watch what you are doing and use common sense. Do not use vacuum cleaner when you

are tired, distracted or under the inﬂuence of drugs, alcohol or medication causing diminished control.

24. WARNING! Do NOT use this vacuum cleaner to vacuum lead paint debris because this may disperse ﬁne

lead particles into the air. This vacuum cleaner is not intended for use under EPA Regulation 40 CFR Part

745 for lead paint material cleanup.

SAVE THESE INSTRUCTIONS

WARNING

– DO NOT LEAVE VACUUM UNATTENDED

WHEN IT IS PLUGGED IN AND/OR OPERATING. UNPLUG UNIT WHEN NOT IN

USE.

GROUNDING INSTRUCTIONS

This appliance must be grounded. If it should malfunction or breakdown, grounding provides a path of

least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with

a cord having an equipment-grounding conductor and grounding plug. The plug must be inserted into an

appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

PAGE 3

GROUNDING INSTRUCTIONS (CONT’D.)

WARNING

– IMPROPER CONNECTION OF THE EQUIPMENT-GROUNDING

CONDUCTOR CAN RESULT IN A RISK OF ELECTRIC SHOCK. CHECK WITH A QUALIFIED

ELECTRICIAN OR SERVICE PERSON IF YOU ARE IN DOUBT AS TO WHETHER THE OUTLET IS

PROPERLY GROUNDED. DO NOT MODIFY THE PLUG PROVIDED WITH THE APPLIANCE – IF

IT WILL NOT FIT THE OUTLET, HAVE A PROPER OUTLET INSTALLED BY A QUALIFIED

ELECTRICIAN.

This appliance is for use on a nominal 120-volt circuit, and has a grounded plug that looks like the plug

illustrated in sketch A. A temporary adaptor that looks like the adaptor illustrated in sketches B and C may

be used to connect this plug to a 2-pole receptacle as shown in sketch B if a properly grounded outlet is

not available. The temporary adaptor should be used only until a properly grounded outlet (sketch A) can

be installed by a qualiﬁed electrician. The green colored rigid ear, lug or the like extending from the adaptor

must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the

adaptor is used, it must be held in place by a metal screw.

IN CANADA, THE USE OF A TEMPORARY ADAPTOR IS NOT PERMITTED BY THE CANADIAN ELECTRICAL

CODE. Make sure that the appliance is connected to an outlet having the same conﬁguration as the plug. No

adaptor should be used with this appliance.

EXTENSION CORDS

When using the appliance at a distance where an extension cord becomes necessary, a

3-conductor grounding cord of adequate size must be used for safety, and to prevent loss

of power and overheating. Use Table A to determine A.W.G. wire size required. To determine

ampere rating of your vacuum, refer to nameplate located on motor housing. Before using

appliance, inspect power cord for loose or exposed wires and damaged insulation. Make any needed repairs

or replacements before using your appliance. Use only three-wire outdoor extension cords which have

three prong grounding-type plugs and three-pole receptacles which accept the extension cord’s plug. When

vacuuming liquids, be sure the extension cord connection does not come in contact with the liquid.

NOTE: STATIC SHOCKS ARE COMMON IN DRY AREAS OR WHEN THE RELATIVE HUMIDITY OF THE AIR IS

LOW. THIS IS ONLY TEMPORARY AND DOES NOT AFFECT THE USE OF THE APPLIANCE. TO REDUCE THE

FREQUENCY OF STATIC SHOCKS IN YOUR HOME, THE BEST REMEDY IS TO ADD MOISTURE TO THE AIR WITH

A CONSOLE OR INSTALLED HUMIDIFIER.

UNPACKING

Remove vacuum cleaner and all accessories from the carton. Important: Open tank cover by pushing latches

or clamps outward with thumbs and remove any accessories that may have been shipped in the tank.

SKETCH A SKETCH B SKETCH C

GROUNDING METHODS

Volts

Total length of cord in feet

120V

Ampere Rating

More Not More

Than Than

0 - 6

6 - 10

10 - 12

12 - 16

25 50 100

150

AWG

Not recommended

TABLE A

PAGE 4

PAGE 5

ASSEMBLY

TOP HANDLE

If the top handle is not installed on your unit, align holes in handle and holes in motor

cover and secure with screws provided.

CASTER SYSTEM

Follow the instructions for the caster system that came with your vacuum.

METAL TANK WITH PLASTIC DOLLY AND FOUR CASTERS

You will ﬁnd four casters with your wet/dry vacuum. Assemble as follows:

1. With the cord disconnected from the receptacle and tank cover removed, turn tank upside down so that

bottom is facing up.

2. Insert casters into bottom of dolly by placing stem of caster into holes provided. Apply

pressure and twisting motion until casters snap into place.

3. Return tank to upright position.

CASTER DOLLY/TOOL HOLDER ASSEMBLY

You will find four casters, one tool holder and two screws with your wet/dry vacuum.

Assemble as follows:

1. With cord disconnected from receptacle and tank cover removed, turn tank upside down so that bottom

is facing up.

2. If the casters are not already installed in dolly, insert casters into bottom of dolly by

placing stem of caster into holes provided. Apply pressure and twisting motion until

casters snap into place.

3. Take tool holder and place in slots on back of dolly. Secure with

screws provided.

4. Return tank to upright position.

METAL TANK WITH PLASTIC DOLLY AND REAR WHEELS

You will ﬁnd two casters, two large rear wheels, one axle, tool rack, four screws, two metal washers, and

two hair pin clips. If your vacuum is 16 U.S. gallons (60.5 litres) or larger you will also ﬁnd two screws, two

metal ﬂat washers and two square nuts with your wet/dry vacuum. Assemble as follows:

1. Make sure the cord is disconnected from the receptacle then remove the tank cover.

2. If your unit is 4 U.S. gallon (15.1 liter) to 14 U.S. gallon (53 liter), assemble as follows:

a. Turn tank upside down so the bottom is facing up.

b. Continue on to step 4 below.

3. If your unit is 16 U.S. gallon (60.5 liter) or above, assemble as follows:

a. With the tank upright and back facing you, insert square nut into one of the two

slots located in back of dolly.

b. Place metal ﬂat washer over stem of screw.

PAGE 6

ASSEMBLY (CONT’D)

c. Tilt the tank forward slightly and locate the hole provided in the underside of the

dolly directly below the slot containing the square nut.

d. Place the screw, containing the ﬂat washer, into the hole and turn clockwise until end of screw is

connected to square nut. If you have difﬁculty getting the screw to connect to the square nut, push

downward on the square nut with the eraser end

of a pencil while turning the screw.

e. Finish tightening the screw using 7/16” socket, wrench or nut driver.

f. Repeat steps a to e with the second slot in dolly.

g. Turn tank upside down so bottom is facing up. Continue on to step 4 below.

4. Place one hair pin clip in one end of axle. Slide one washer down the length of the

axle to rest on the hair pin clip. Slide wheel onto axle next to washer. Be sure flat side

of wheel hub is facing outward.

5. Slide axle through holes provided in tool rack.

6. Slide remaining wheel then washer onto axle. Insert hair pin clip into remaining hole

in axle to hold wheel in place.

7. Install tool rack assembly onto dolly (already installed on tank) by placing large slot in

tool rack over rim on back of dolly. Push tool rack onto dolly until the bottom of tool

rack is ﬂush with bottom of dolly.

NOTE: It is normal for tool rack to ﬁt tightly onto dolly.

8. Secure with four screws provided.

9. If plastic ﬂat washers are included in hardware pack, place one ﬂat washer over stem of each caster.

NOTE: Flat washers are not required with all units.

10. Insert casters into front of dolly by placing stem of casters into holes provided. Apply

pressure and twisting motion until casters snap into place.

11. Return tank to upright position.

PAGE 7

ASSEMBLY (CONT’D)

CARRIAGE HANDLE

Follow the instructions for the carriage handle that came with your vacuum.

If your side tank handles look like the ones pictured to the right, follow these instructions.

You will ﬁnd one carriage handle and a handle pack containing two side tank handles, four handle supports

and eight screws. Assemble as follows:

1. Take two handle supports and two 1” screws. Place screws through the hole provided

in center of each support.

2. Position the tank, in the upright position, with the inlet facing you. Put the support

assemblies inside the tank, then place the screws through the holes provided on left

side of the tank. Make sure the plastic portion is located inside the tank. Turn the

supports until the back of the supports ﬁt ﬂush against the inside curve of the tank.

3. Remove any webbing that attaches the tank handles to each other. Take the side tank

handle with the letter L and position it on the outside of the tank where the support

assemblies are installed. The U-shaped cutout on the bottom end of the handle must

face the rear of the tank. Secure the side tank handle to the tank with the screws in

the support assemblies.

4. Repeat steps 1 to 3 using right side of tank and the remaining side tank handle marked with the letter R.

5. Position metal carriage handle outside of tank and under the tank handles. Be sure

to spread ends of carriage handle when assembling to prevent damage to tank. Line

up holes in ends of carriage handle with holes in bottom of tank handles. Make sure

carriage handle is in the U-shaped cut on the tank handles (located towards rear of

unit). Secure with 1½” screws provided.

BASKET

If your unit came with a basket, insert basket through center of carriage handle and slide

into place. The basket does not come standard with all models.

SET UP AND OPERATION

DANGER

– This equipment incorporates parts such as switches, motors or the

like that tend to produce arcs or sparks that can cause an explosion. Do not pick up ﬂammable,

combustible, or hot materials. Do not use around explosive liquids or vapors, as electrical devices

produce arcs or sparks which can cause a ﬁre or explosion - do not use at ﬁlling stations or

anywhere gasoline is stored or dispensed.

FILTER INSTALLATION AND MAINTENANCE

1. Refer to the ﬁlter installation and maintenance section to make sure the correct ﬁlters

are installed for your cleaning operation.

2. Replace tank cover. Make sure each latch or clamp is secured over the raised area

of the tank cover. Failure to properly secure the latches could cause the tank cover to

release from the tank.

3. Install machine hose end into inlet located on the front of the tank.

4. Attach the desired cleaning accessory onto the accessory end of the hose.

NOTE: Many more useful tools are available at your local dealer or the Shop-Vac

website.

5. Plug the cord into the wall outlet. Your cleaner is ready for use.

I = ON, O = OFF

FILTRATION SYSTEM

There are a variety of ﬁlters available for your vacuum. There are cage ﬁlters that install onto the underside

of the tank cover and tank ﬁlters that install into the tank. The ﬁlters are grouped into three ﬁltration

categories. General ﬁltration is used for large debris; such as, wood chips, nails and gravel. Medium

ﬁltration is used for medium debris; such as, dirt, sand and sawdust. Fine ﬁltration is used for ﬁne debris;

such as drywall dust, cold ash and cement dust. It is important to have the correct ﬁlters installed for your

cleaning operation to protect your vacuum motor. THE MOST EFFICIENT FILTRATION FOR YOUR VACUUM IS A

FINE FILTRATION CAGE FILTER WITH A FINE FILTRATION TANK FILTER.

NOTE: When using the vacuum to pick up very ﬁne dust. It will be necessary to empty the tank and clean

the cage ﬁlter at more frequent intervals to maintain maximum pick up power or add a disposable ﬁlter bag.

DRY PICK UP OPERATION

NOTE: Never use the vacuum for dry pick up without a dry use ﬁlter installed. Using the vacuum without a

ﬁlter will cause dust to discharge from the blower port and cause damage to the motor.

WARNING – ALWAYS DISCONNECT THE PLUG FROM THE WALL OUTLET

BEFORE REMOVING THE TANK COVER.

Follow the instructions for the ﬁlter that came with your vacuum. Some ﬁlters mentioned do not come

standard with all vacuums. Additional ﬁlters are available at your local dealer or the Shop-Vac

website.

CARTRIDGE FILTER

The cartridge ﬁlter can be used for dry pick up and small quantities of wet pick up. Installation is the same

for both. When picking up ﬁne dust or powders a high efﬁciency ﬁlter bag must be used with the cartridge

ﬁlter.

1. If a foam sleeve is installed on the lid cage, remove it by sliding it off the lid cage. NOTE: If the cartridge

ﬁlter has been used for wet pick up, it must be cleaned and dried before using it for dry pick up.

2. With the tank cover in an upside down position, slide the cartridge down over the lid

cage, pushing until the ﬁlter seals against the cover.

3. Place the ﬁlter retainer into the top of the cartridge ﬁlter. Hold the tank cover with one

hand, turn the handle on the ﬁlter retainer clockwise to lock the ﬁlter into place.

4. To remove the ﬁlter for cleaning, hold the tank cover and turn the ﬁlter retainer

counter-clockwise to loosen and remove.

PAGE 8

PAGE 9

FILTER INSTALLATION AND MAINTENANCE (CONT’D)

5. Slide the cartridge ﬁlter off the lid cage.

6. For standard cartridge ﬁlters and Ultra-Web

cartridge ﬁlters, clean the ﬁlter by shaking or gently

brushing off excess dirt. Extremely dirty ﬁlters may be cleaned with water by rinsing from the inside of

the ﬁlter. Dry completely (approximately 24 hours).

For CleanStream

Abrasive Resistant cartridge ﬁlter, tap end cap against hard surface to loosen debris.

Additional debris can be removed by rinsing outside surface of the ﬁlter with running water. Avoid

dampening inside of ﬁlter. Completely air dry after washing. IMPORTANT: DO NOT BRUSH. DO NOT clean

ﬁlter with abrasive materials or scrub between pleats. This will permanently damage the ﬁlters ability to

stop dust.

7. Check the ﬁlter for tears or small holes. If none are found, reinstall the ﬁlter. To prevent damage to your

vacuum, do not use a ﬁlter with a hole or tear.

NOTICE – This ﬁlter is made of high quality paper designed to stop small

particles of dust. The ﬁlter can be used for wet or dry pick up. A dry ﬁlter is necessary to

pick up dry material. If you use your vac to pick up dust when the ﬁlter is wet, the ﬁlter

will clog quickly and be very difﬁcult to clean. The ﬁlter may become saturated when

picking up large quantities of liquid causing misting to appear in the exhaust air. At this

time, you should dry or change the ﬁlter to eliminate this occurrence. Please handle the

ﬁlter carefully when removing it for cleaning or when installing it. Check the ﬁlter for tears

or small holes. Even a small hole can cause dust to be exhausted. Do not use a ﬁlter with

holes or tears. Replace it immediately.

WARNING – KEEP FILTERS CLEAN. EFFICIENCY OF THE VACUUM IS LARGELY

DEPENDENT ON THE FILTER. A CLOGGED FILTER CAN CAUSE OVERHEATING AND POSSIBLY

DAMAGE THE CLEANER. CHECK THE FILTER PERIODICALLY AND REPLACE AS REQUIRED.

DISPOSABLE FILTER BAG

Use the disposable ﬁlter bag in conjunction with the cartridge ﬁlter for easy disposal of the debris. The bag

is not required for normal dry pick up. When picking up ﬁne dust or powders a high efﬁciency ﬁlter bag

must be used. NOTE: For dry use only.

TANK WITH REMOVABLE INLET DEFLECTOR:

1. Make sure the cord is disconnected from the receptacle, tank cover is removed and the hose is

disconnected from tank inlet.

2. Remove inlet deﬂector from deﬂector guide. NOTE: Hose must be removed before inlet

deﬂector can be taken out.

3. With the opening of the inlet deﬂector facing the left or right side of the ﬁlter bag, slide

ﬁlter bag collar over deﬂector matching notches of bag collar to tabs on inlet deﬂector.

Bag will only ﬁt properly one way.

4. Slide deﬂector with ﬁlter bag attached into deﬂector guide.

5. Reinsert hose into inlet and tighten locking-nut. When secured in place expand bag and position around

inside of tank.

FILTER INSTALLATION AND MAINTENANCE

(CONT’D)

6. NOTE: When removing ﬁlter bag from tank, remove inlet deﬂector from ﬁlter bag collar and reinstall into

deﬂector guide. Inlet deﬂector should always be in place for any type of cleaning.

WARNING – FOR FINE DUST AND POWDERS.

When vacuuming ﬁne dust, or powders of any kind (plaster, drywall dust, cold ashes, concrete dust, etc.)

a high efﬁciency drywall ﬁlter bag must be used. When vacuuming normal household dust and debris,

standard household disposable ﬁlter bags may be used.

WET PICK UP OPERATION

1. Your vacuum can be used for wet pick up. Remove ALL dirt and debris found in the

tank. Remove all dry use ﬁlters, including the ﬁlter bag, from the vacuum.

2. A clean cartridge ﬁlter may be used to pick up small quantities of liquid. To use the

cartridge ﬁlter; follow the instructions under dry pick up.

3. For vacuuming large quantities of liquid use a foam sleeve. If a foam sleeve did not

come standard with your unit, one may be purchased at your local dealer, the Shop-

Vac

website or by contacting Shop-Vac

customer service. To use the foam sleeve;

follow the instructions in this section.

4. Misting in the exhaust air or dripping of liquid around the tank cover may occur if the ﬁlter becomes

saturated during wet pick up. If this occurs, remove the ﬁlter and allow to dry, or replace with another dry

ﬁlter.

5. Turn the unit off immediately upon completing a wet pick up job or when tank is full and ready to be

emptied. When the tank is full, suction will drastically reduce. Refer to the automatic suction shut

off section for more information. Raise the hose to drain any excess liquid into the tank. Follow the

instructions in the emptying liquid waste section.

6. Before storing the vacuum cleaner or using for dry pick up, clean and dry the interior of the tank and the

underside of the tank cover. Clean and allow the ﬁlters to dry completely.

7. Wet pick up accessories should be washed periodically; especially after picking up wet, sticky kitchen

accidents. This can be accomplished with a warm solution of soap and water.

FOAM SLEEVE

1. With the tank cover in an upside down position, slide the foam sleeve down over the lid cage, pulling

until foam sleeve completely covers the lid cage.

2. To clean the foam sleeve, slide it up and off the lid cage. Shake excess debris off of the foam sleeve with

a rapid up and down movement.

3. Hold foam sleeve under running water for a couple minutes, rinsing from the inside of the ﬁlter. A water

wash is not always required, depending on the condition of the ﬁlter.

4. Check the ﬁlter for tears. If any are found, replace with a new ﬁlter.

BLOWER FEATURE

Your vacuum can be used as a powerful blower. To use the blower feature, clear the hose

of any debris or obstructions.

For vacuums with a blower port cover (not standard on all models), unscrew blower

port cover located on the back of tank cover. The blower port cover is equipped with

a retaining strap to prevent loss of the cover. NOTE: For maximum performance when

vacuuming, remove the blower port cover.

Insert machine hose end into blower port located on the back of the tank cover.

Twist the hose end slightly to tighten the connection. Caution should be used when using as a blower due to

the powerful force of air when using certain attachments.

WARNING – ALWAYS WEAR EYE PROTECTION TO PREVENT ROCKS OR

DEBRIS FROM BEING BLOWN OR RICOCHETING INTO THE EYES OR FACE WHICH CAN RESULT

IN SERIOUS INJURY.

PAGE 10

EMPTYING LIQUID WASTE FROM THE TANK

To empty liquid waste from the tank, turn the vacuum off and remove the plug from the wall outlet. Follow

the instructions that pertain to your vacuum.

WITHOUT TANK DRAIN

Remove the tank cover and deposit the liquid waste in a suitable drain. Use side carry handles for lifting vac

when draining tank into drains that are located above ﬂoor level. After tank is empty, return the tank cover to

its original position.

WITH TANK DRAIN

Remove the drain cap and deposit the liquid waste in a suitable drain. Use side carry handles for lifting vac

when draining tank into drains that are located above ﬂoor level. After the tank is empty, return the drain

cap to it’s original position.

AUTOMATIC SUCTION SHUT OFF

The vacuum is equipped with an automatic suction shut-off that operates when picking up liquids. As the

level of the liquid rises in the tank, an internal ﬂoat rises until it seats itself against a seal at the intake of

the motor, shutting off suction. When this happens, the motor will develop a higher than normal pitch noise

and the suction is drastically reduced. If this occurs, turn unit off immediately. Failure to turn unit off after

ﬂoat rises and shuts off suction will result in extensive damage to the motor. To continue use, empty the

liquid waste from the tank as outlined in the previous section.

NOTE: IF ACCIDENTALLY TIPPED OVER, THE VACUUM COULD LOSE SUCTION, IF THIS OCCURS, TURN UNIT

OFF AND PLACE VAC IN UPRIGHT POSITION. THIS WILL ALLOW THE FLOAT TO RETURN TO ITS NORMAL

POSITION AND YOU WILL BE ABLE TO CONTINUE OPERATION.

LUBRICATION

No lubrication is necessary as the motor is equipped with lifetime lubricated bearings.

STORAGE

Before storing your vacuum the tank should be emptied and cleaned. Never allow liquids to sit in the tank

for any extended period of time. The vacuum should be stored indoors.

SERVICE

Do not attempt to service your Shop-Vac

wet/dry vacuum cleaner beyond that described in this manual.

Refer all other servicing to a qualiﬁed service center.

PAGE 11

PAGE 12

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSES SOLUTION

Parts/accessories 1. Packed in tank 1. Check in tank

missing

Vacuum cleaner 1. No power at receptacle 1. Check for power

will not start 2. Defective switch 2. Contact Shop-Vac

customer service

3. Defective motor 3. Contact Shop-Vac

customer service

Dust discharging 1. Filter not installed/not installed 1. Properly install filter

from exhaust properly

2. Filter damaged 2. Replace filter

3. Filter clogged or dust is too fine 3. Use more efficient filter

4. Filter not functional 4. Clean or replace filter

Loss of suction 1. Loose hose connection 1. Tighten hose connection

2. Filter clogged 2. Clean or replace filter

3. Full tank 3. Empty tank

4. Hole in hose 4. Replace hose

Static shock 1. Dry environment 1. Add moisture to air (if

practical, use a console

or installed humidifier).

2. Relative humidity of air is low 2. This situation is temporary

and does not affect the use

of the vacuum cleaner.

WARNING – IF ANY OF THE MOTOR HOUSING PARTS SHOULD BECOME

DETACHED OR BROKEN, EXPOSING THE MOTOR OR ANY OTHER ELECTRICAL COMPONENTS,

OPERATION SHOULD BE DISCONTINUED IMMEDIATELY TO AVOID PERSONAL INJURY OR

FURTHER DAMAGE TO THE VACUUM. REPAIRS SHOULD BE MADE BEFORE REUSING THE

VACUUM.

PAGE 13

FIVE YEAR INDUSTRIAL/COMMERICAL WARRANTY

Five year limited warranty

Shop-Vac

Corporation warrants the vacuum cleaner contained in this package for ﬁve year from the

date of purchase to correct by repair or parts replacement without charge any product defect due to faulty

material or workmanship. Should this product be used for rental service, a 90 day limited warranty will

apply. THIS WARRANTY DOES NOT COVER ACCESSORIES. Shop-Vac

assumes no responsibility for damage

or faulty performance caused by misuse or careless handling, or where repairs or modiﬁcations have been

made or attempted by others. Proof of purchase date is required. This warranty gives you speciﬁc legal

rights, and you may also have other rights which vary from state to state or province to province.

Customers in the United States: for product service contact Shop-Vac

Corporation Customer Service, at

(570) 326-3557 or go to www.shopvac.com/support. Visit www.shopvac.com for your vacuum’s parts

list schematic.

Customers in Canada: for product service return the complete unit, (transportation prepaid), to the

Authorized Shop-Vac® Service Centre nearest you. A complete list of Authorized Service Centres is included

with each vacuum cleaner.

Customers in Mexico: for product service see paperwork that came with your unit.

PAGE 14

SHOP-VAC CORPORATION

2323 Reach Road, P.O. Box 3307

Williamsport, PA 17701-0307

(570) 326-3557

www.shopvac.com

SHOP-VAC CANADA

1770 Appleby Line

Burlington, Ontario L7L 5P8

(905) 335-9730

www.shopvac.ca

Shop Vac-México, S.A. de C.V.

Paseo de los Adobes 1081-3

Fraccionamiento Guadalajara Technology Park

Zapopan, Jalisco, México C.P. 45019

Patents Issued and Pending.

MANUEL D’UTILISATION

Série :

87MT

92M

92L

ATTENTION!

DANGER!

Lisez attentivement tous les règlements relatifs à la sécurité avant

d’essayer de faire fonctionner l’appareil. Conservez-les pour référence

ultérieure.

Ne faites jamais fonctionner cet appareil en présence de

matières ou de vapeurs inﬂammables, car les dispositifs

électriques produisent des arcs électriques ou des étincelles

qui risquent de provoquer un incendie ou une explosion. NE

LAISSEZ JAMAIS L’APPAREIL EN FONCTIONNEMENT SANS

SURVEILLANCE!

À usage commercial et industriel

ASPIRATEUR SEC/HUMIDE

Pour vos dossiers, veuillez noter les renseignements suivants et

conserver ce mode d’emploi dans un endroit sûr.

N° de catalogue

N° de modèle

Date d’achat :

(Situé sur la boîte)

(Situé sur la partie supérieure de l’aspirateur)

87557-84

TABLE DES MATIÈRES

Directives importantes de sécurité ..................................................................................

Directives relatives à la mi se à la terre ..............................................................................

Rallonges ........................................................................................................................

Déballage ..........................................................................................................................

Assemblage ....................................................................................................................

Conﬁguration et fonctionnement ........................................................................................

Installation et entretien du ﬁltre ...................................................................................

Caractéristiques du soufﬂeur ............................................................................................

Vidange des déchets liquides du réservoir .......................................................................

Arrêt automatique de l’aspiration .....................................................................................

Lubriﬁcation ....................................................................................................................

Rangement ......................................................................................................................

Entretien ..........................................................................................................................

Dépannage ......................................................................................................................

Garantie et coordonnées ..................................................................................................

3-4

4-5

5-8

8-11

SECTION PAGES

• Lunette de sécurité

• Clé ou douille de

/8 po,

/16 po,

(2)

/16 po et (2)

/2 po (n'est

pas nécessaire avec tous les

aspirateurs)

• Tournevis à tête plate

OUTILS NÉCESSAIRES

PAGE 2

DIRECTIVES IMPORTANTES DE SÉCURITÉ

Lors de l’utilisation d’un appareil électrique, il faut toujours respecter des précautions de base notamment

celle-ci : LISEZ TOUTES LES DIRECTIVES AVANT L’UTILISATION DE CET APPAREIL.

AVERTISSEMENT- POUR RÉDUIRE LE RISQUE D’INCENDIE, DE

DÉCHARGE ÉLECTRIQUE OU DE BLESSURES :

1. Ne quittez pas l’appareil s’il est branché. Débranchez la ﬁche de la prise lorsque l’appareil n’est pas

utilisé et avant tout entretien. Branchez uniquement à une prise correctement mise à la terre. Consultez

les directives relatives à la mise à la terre.

2. Protégez l’appareil de la pluie; rangez-le à l’intérieur.

3. L’appareil n’est pas un jouet. Soyez attentif lors de l’utilisation de l’appareil par des enfants ou près de

ceux-ci.

4. Utilisez l’appareil uniquement comme décrit dans le présent manuel. Utilisez également uniquement les

accessoires recommandés par le fabricant.

5. N’utilisez pas l’appareil avec un cordon d’alimentation ou une ﬁche endommagé(e). Communiquez avec

le Service d’assistance de Shop-Vac

si l’appareil ne fonctionne pas comme prévu, a subi un choc, est

endommagé, a été oublié à l’extérieur ou s’il a été immergé dans l’eau.

6. Ne pas : tirer sur le cordon d’alimentation ou transporter l’appareil par celui-ci, l’utiliser comme

poignée, fermer une porte sur le cordon ni le contraindre sur des bords tranchants ou des coins. Ne

passez pas l’appareil sur le cordon d’alimentation. Tenez le cordon d’alimentation à l’écart des surfaces

chauffées.

7. Ne tirez pas sur le cordon d’alimentation pour débrancher l’appareil. Pour ce faire, saisissez la ﬁche et

non le cordon d’alimentation.

8. Ne manipulez pas la ﬁche ou l’appareil avec des mains mouillées.

9. N’insérez aucun objet dans les ouvertures. N’utilisez pas l’appareil avec des ouvertures bloquées,

maintenez-les exemptes de poussières, de peluches, de cheveux ou de tous éléments qui pourraient

réduire l’admission d’air.

10. Tenez les cheveux, les vêtements amples, les doigts et toutes parties du corps à l’écart des ouvertures

et des pièces mobiles.

11. N’aspirez aucun élément qui brûle ou qui émet de la fumée comme des cigarettes, des allumettes ou

des cendres chaudes.

12. Ne faites pas fonctionner l’appareil sans le sac à poussière et/ou les ﬁltres en position.

13. Éteignez toutes les commandes avant de le débrancher.

14. Soyez très attentif lors du nettoyage dans les escaliers.

15. N’utilisez pas l’appareil pour aspirer des liquides inﬂammables ou combustibles comme de l’essence.

Ne le faites pas fonctionner en présence de tels liquides.

16. N’utilisez pas l’aspirateur comme un vaporisateur de liquides inﬂammables comme des peintures à

base d’huile, des vernis-laques, des produits de nettoyage domestiques, etc.

17. N’aspirez pas de matières toxiques, cancérogènes, combustibles ou dangereuses comme de l’amiante,

de l’arsenic, du baryum, du béryllium, du plomb, des pesticides ou d’autres matières pouvant porter

atteinte à la santé. Des modèles sont spécialement conçus et offerts pour ces travaux.

18. N’aspirez pas de particules de suie ou de poussières de ciment, de plâtre ou de cloison sèche sans le

ﬁltre à cartouche et le sac-ﬁltre à poussière en position. Ces particules sont très ﬁnes et risquent de

passer à travers la mousse et ainsi nuire au rendement du moteur ou d’être rejetées dans l’atmosphère.

Des sacs-ﬁltres à poussière supplémentaires sont offerts.

19. Une fois le service de nettoyage terminé, ramassez le cordon d’alimentation déployé sur le plancher. Il

risque de faire trébucher un passant.

20. Soyez particulièrement prudent lors de la vidange de réservoirs pleins et lourds.

21. Pour éviter tout risque de combustion spontanée, videz le réservoir après chacune des utilisations.

22. L’utilisation d’un aspirateur utilitaire peut se solder par la projection de corps étrangers qui pourraient

blesser les yeux. Portez toujours des lunettes de sécurité lors de l’utilisation de l’aspirateur.

23. SOYEZ VIGILANT. Notez vos actions et vos déplacements et utilisez votre jugement. N’utilisez pas

l’aspirateur ménager si vous êtes fatigué(e), distrait(e) ou sous l’inﬂuence de drogues, d’alcool de

médicaments qui risque(nt) d’affaiblir vos facultés.

24. AVERTISSEMENT! Ne PAS utiliser cet aspirateur pour ramasser des débris de peinture à base de

plomb, car ceci peut disperser de ﬁnes particules dans l’air.Cet aspirateur n’est pas conçu pour

l’utilisation lors du nettoyage de matériel de peinture à base de plomb sous le règlement 40

CFR pièce 745 d’EPA.

PAGE 3

CONSERVEZ CES DIRECTIVES

AVERTISSEMENT

– NE LAISSEZ PAS L’ASPIRATEUR

SANS SURVEILLANCE S’IL EST BRANCHÉ OU EN FONCTIONNEMENT.

DÉBRANCHEZ L’APPAREIL LORSQU’IL N’EST PAS UTILISÉ.

DIRECTIVES RELATIVES À LA MISE À LA TERRE

Cet appareil doit être mis à la terre. En cas de défectuosité ou de bris, la mise à la terre offre une voie de

moindre résistance pour le passage du courant électrique et réduit ainsi le risque de décharge électrique.

Cet appareil est muni d’un cordon d’alimentation doté d’un ﬁl conducteur et d’une ﬁche mise à la terre. Il

faut insérer la ﬁche dans une prise correspondante adéquate correctement installée et mise à la terre en

conformité avec tous les codes et toutes les ordonnances locales en vigueur.

AVERTISSEMENT– UNE CONNEXION INCORRECTE DU CONDUCTEUR

DE TERRE DU MATÉRIEL PEUT CRÉER UN RISQUE DE DÉCHARGE ÉLECTRIQUE. VÉRIFIEZ

AUPRÈS D’UN ÉLECTRICIEN PROFESSIONNEL OU DE PERSONNEL QUALIFIÉ EN ENTRETIEN

ET RÉPARATION SI VOUS AVEZ DES DOUTES RELATIFS À LA BONNE MISE À LA TERRE

DE LA PRISE. NE MODIFIEZ PAS LA FICHE FOURNIE AVEC L’APPAREIL. SI ELLE N’EST

PAS COMPATIBLE AVEC LA PRISE, FAITES CHANGER LA PRISE PAR UN ÉLECTRICIEN

PROFESSIONNEL.

Cet appareil est conçu pour fonctionner sur un circuit de 120 volts de tension nominale et il est muni

d’une ﬁche mise à la terre semblable à celle illustrée au croquis A. Il est possible d’utiliser un adaptateur

temporaire semblable à celui illustré aux croquis B et C pour raccorder cette prise à un réceptacle bipolaire

comme illustré au croquis B, si une prise correctement mise à la terre n’est pas disponible. Utilisez cet

adaptateur temporaire jusqu’à l’installation d’une prise correctement mise à la terre (croquis A) par un

électricien professionnel. L’oreille ou la cosse rigide (ou un élément semblable) de couleur verte qu fait

saillie de l’adaptateur doit être raccordée à une mise à la terre permanente comme le couvercle d’une boîte

à prises correctement mise à la terre. À chacune des utilisations de l’adaptateur, il faut le ﬁxer en place

avec une vis métallique.

AU CANADA, L’UTILISATION D’UN ADAPTATEUR PROVISOIRE N’EST PAS AUTORISÉE PAR LE CODE CODE

CANADIEN DE L’ÉLECTRICITÉ. Assurez-vous que l’appareil est relié à une prise ayant la même conﬁguration

que la ﬁche. Aucun adaptateur ne devrait être utilisé avec cet appareil.

RALLONGES

Lorsque vous passez l’aspirateur à une distance qui nécessite l’utilisation d’une rallonge, vous

devez utiliser un cordon de mise à la terre à 3 conducteurs de calibre adéquat pour assurer la

sécurité et empêcher la perte de puissance et la surchauffe de l’appareil. Utilisez le Tableau

A pour déterminer le calibre de ﬁl AWG requis. Pour déterminer l’intensité nominale de votre

appareil, reportez-vous à la plaque située sur le capot du moteur. Avant d’utiliser l’appareil, inspectez le

cordon d’alimentation pour déceler les ﬁls desserrés ou exposés et les dommages d’isolation éventuels.

Procédez à toutes les réparations et à tous les remplacements nécessaires avant d’utiliser votre appareil.

Utilisez uniquement les rallonges pour l’extérieur, à trois ﬁls, munies de ﬁches de mise à la terre à trois

broches et les prises de courant trois pôles qui acceptent la ﬁche de la rallonge. Lorsque vous utilisez votre

aspirateur pour ramasser des liquides, assurez-vous que le branchement de la rallonge ne contacte pas le

liquide.

MÉTHODES DE MISE À LA TERRE

CROQUIS A CROQUIS B CROQUIS C

PAGE 4

RALLONGES (SUITE)

REMARQUE : LES DÉCHARGES STATIQUES SONT COURANTES DANS LES ENDROITS SECS OU LORSQUE

L’HUMIDITÉ RELATIVE DE L’AIR EST FAIBLE. IL S’AGIT DE CONDITIONS TEMPORAIRES QUI N’AFFECTENT PAS

L’UTILISATION DE L’APPAREIL. LA MEILLEURE SOLUTION POUR RÉDUIRE LA FRÉQUENCE DES DÉCHARGES

STATIQUES DANS VOTRE MAISON CONSISTE À HUMIDIFIER L’AIR À L’AIDE D’UN HUMIDIFICATEUR À POSER

OU FIXE.

DÉBALLAGE

Sortir l’aspirateur et tous les accessoires de la boite en carton. Important : Ouvrir le couvercle de la cuve en

poussant sur les verrous avec les pouces. Sortir ensuite tous les accessoires qui se trouvent dans la cuve.

ASSEMBLAGE

POIGNÉE SUPÉRIEURE

Si la poignée supérieure n’est pas installée sur votre appareil, alignez les oriﬁces du

manche avec ceux du couvercle du moteur et ﬁxez au moyen des vis fournies.

SYSTÈME À ROULETTES

Suivez les instructions du système de roulette fourni avec votre aspirateur.

RÉSERVOIR MÉTALLIQUE AVEC CHARIOT DE PLASTIQUE ET QUATRE ROULETTES

Vous trouverez quatre roulettes avec votre aspirateur pour déchets secs et humides. Assemblez comme

suit :

1. Alors que le cordon est débranché de la prise et que le couvercle du réservoir est

enlevé, retournez le réservoir de sorte que le bas fait face vers le haut.

2. Insérez les roulettes dans la partie inférieure du chariot en plaçant la tige des

roulettes dans les oriﬁces prévus à cette ﬁn. Appliquez une pression et un

mouvement de torsion jusqu’à ce que les roulettes s’enclenchent.

3. Retournez le réservoir en position verticale.

ASSEMBLAGE DU CHARIOT À ROULETTES ET DU PORTE-OUTILS

Vous trouverez quatre roulettes, un porte-outils et deux vis avec votre aspirateur avec l’aspirateur pour

débris secs et humides.

Assemblage :

1. Avec le cordon débranché du réceptacle et le couvercle de la cuve retiré, tournez la cuve à l’envers pour

que le fond soit face vers le haut.

2. Si les roulettes ne sont pas déjà installées sur le chariot, insérez les roulettes au bas

du chariot en plaçant les tiges de roulettes dans les oriﬁces prévus à cette ﬁn. Exercez

une pression et un mouvement de rotation jusqu’à ce que les roulettes s’enclenchent.

Tension

Longueur totale de la

rallonge, en pieds

120V

Intensité nominale

0 - 6

6 - 10

10 - 12

12 - 16

25 50 100

150

AWG

(cabre américain normalisé de fils)

Non recommandé

Plus

Pas

Plus de

Tableau A

PAGE 5

ASSEMBLAGE (SUITE)

3. Prenez le porte-outils et mettez-le dans les fentes qui se

trouvent à l’arrière du chariot. Fixez-le avec les vis fournies.

4. Remettez-la cuve en position verticale.

RÉSERVOIR MÉTALLIQUE AVEC CHARIOT DE PLASTIQUE ET ROUES ARRIÈRE

Vous trouverez deux roulettes, deux grandes roues arrière, un essieu, un porte-outil, quatre vis, deux

rondelles métalliques, et deux bagues de retenue. Si votre aspirateur comporte 16 gallons (60,5 litres)

ou plus, vous trouverez également deux vis, deux rondelles métalliques et deux écrous carrés avec votre

aspirateur sec/humide. Assemblez comme suit :

1. Assurez-vous que le cordon est débranché de la prise, puis retirez le couvercle du réservoir.

2. S’il s’agit d’un appareil de 15,1 à 53 litres (4 à 14 gallons), assemblez comme suit :

a. Retournez le réservoir de sorte que le bas fait face vers le haut.

b. Passez à l’étape 4 ci-dessous.

3. S’il s’agit d’un appareil de 60,5 litres (16 gallons) ou plus, assemblez comme suit :

a. Alors que le réservoir est en position verticale et que le dos vous fait face, insérez

l’écrou carré dans l’une des deux fentes situées à l’arrière du chariot.

b. Placez la rondelle plate en métal sur la tige de la vis.

c. Inclinez le réservoir légèrement vers l’avant et localisez l’oriﬁce dans la partie

inférieure du chariot se trouvant directement sous la fente contenant l’écrou carré.

d. Placez la vis contenant la rondelle plate dans l’oriﬁce et tournez vers la droite jusqu’à ce que

l’extrémité de la vis soit reliée à l’écrou carré. Si vous avez des difﬁcultés à relier la vis à l’écrou

carré, enfoncez l’écrou carré avec de la gomme d’un crayon tout en vissant la vis.

e. Achevez de serrer la vis à l’aide d’une douille, d’une clé ou d’un tourne-écrou de 7/16 po.

f. Répétez les étapes a à e de la deuxième fente dans le chariot.

g. Retournez le réservoir de sorte que le bas fait face vers le haut. Passez à l’étape 4 ci-dessous.

4. Placez une bague de retenue à une extrémité de l’essieu. Faites glisser une rondelle

le long de l’essieu de manière à ce qu’elle repose sur la bague de retenue. Faites

glisser la roue sur l’essieu, à côté de la rondelle. Assurez-vous que le côté plat du

moyeu de la roue est tourné vers l’extérieur.

5. Faites glisser l’essieu à travers les orifices prévus dans le porte-

outil.

6. Faites glisser le reste de la roue puis la rondelle sur l’essieu. Insérez la bague

de retenue dans l’orifice restant de l’essieu pour faire tenir la roue en place.

PAGE 6

La page charge ...

Shop Vac 92LSQ650 Manuel utilisateur

Marque: Shop Vac

Modèle: 92LSQ650

Catégorie: Aspirateurs

Taper: Manuel utilisateur

Ce manuel convient également à

92MSQ650

Télécharger le PDF

rapport

dans d''autres langues

English: Shop Vac 92LSQ650 User manual
español: Shop Vac 92LSQ650 Manual de usuario

Shop Vac 92LSQ650 Manuel utilisateur

Ce manuel convient également à

Shop Vac 92LSQ650 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents