Estate TUD8700WD1 Guide d'installation

Catégorie
Lave-vaisselle
Taper
Guide d'installation
INSTALLATION iNSTRUCTiONS
UNDERCOUNTER DISHWASHER
PLASTIC GIANT TUBMODELS
iNSTRUCTiONS D'INSTALLATION
LAVE--VAISSELLEENCASTRE
MODELES A TRESGRANDE CUVE EN PLASTIQUE
Table of Contents ................................... 2
Table des matieres .................................. 21
W10142914
Table of Contents
Dishwasher Safety ................................. 2
Installation Requirements ........................... 3
Tools and Parts ................................... 3
Location Requirements ............................ 3
Drain Requirements ............................... 5
Water Supply Requirements ........................ 5
Electrical Requirements ............................ 5
Installation Instructions ............................. 6
Prepare Cabinet Opening--Existing Utilities ........... 6
Prepare Cabinet Opening--New Utilities .............. 6
Prepare and Route Water Line ...................... 7
Install Drain Hose ................................ 8
Installation Instructions (cont.).........................
Prepare Dishwasher ............................. 10
Make Power Cord Electrical Connection ............. 11
Determine Cabinet Opening ....................... 12
Move Dishwasher into Cabinet Opening ............. 13
Connect to Water Supply ......................... 15
Connect to Drain ................................ 16
Make Direct Wire Electrical Connection .............. 16
Secure Dishwasher in Cabinet Opening ............. 18
Complete Installation ............................. 19
Check Operation ................................. 20
If Dishwasher Does Not Operate ................... 20
Additional Tips .................................. 20
DISHWASHERSAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured ifyou don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Tip Over Hazard
Do not use dishwasher until completely installed.
Do not push down on open door.
Doing so can result in serious injury or cuts.
You Need to:
Slowly open dishwasher door while someone grasps the
rear of the dishwasher. Remove shipping materials, drain
hose and lower rack. Close dishwasher door until latched.
Observe all governing codes and ordinances.
Install this dishwasher as specified in these instructions.
Installation should be performed by a qualified service
technician. The dishwasher must be installed to meet all
electrical and plumbing national and local codes and
ordinances.
2
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the recommended tools and parts before starting
installation. Read and follow the instructions provided with
any tools listed here.
All installations
Tools needed:
IFlat-blode
Fliers I screwdriver
5/16" and 1/4" _ UL listed or CSA _ n
nut drivers or _7" approved twist-on U U
hex sockets _,_" wire connectors*
ii -
10 adjustable wrench 5 8" o_en end
/ F -
that opens to wrench _
1-1.8" (2.9 cm) U =' _ ,
*Must be the proper size to connect your household wiring
to 16-gauge wiring in dishwasher
Other useful items you may need:
4 ?
Fos,oht othtowo
Parts supplied:
12 !Drain hOseclamp__ Drai_ [ 2 _#10xli2.
PhillipsLhead
(!,a,_,,d l_a 1) screws
Silver Green [
Make sure all these parts are included in the literature package.
Parts needed:
90tiEIb0w fitting with Teflon® tape or pipe joint
3/8 N:P.T. external threads compound
(the 0the[ end mus t fit you i
water suDulv line) ( _ _. "_
j
Other parts you may also need:
I s,0o,,tctto e
(38:1-5 0 cm) I for solid surface I du
screw4ype c0untertops @
camps{3max) J PartNo.8212560
NOTE: Parts available for purchase in plumbing supply stores.
Check local codes. Check existing electrical supply. See
"Electrical Requirements" section. It is recommended that
electrical connections be made by a licensed electrical installer.
® Teflon is a registered trademark of E.I. Du Pont de Nemours and Company.
In addition, for first time installations
Tools needed:
Parts needed:
,u
Copper tubing (3/8"
O.D, suggested) or
flexible braided
water Supply line
See "Electrical Requirements" section
Foi Direct Wire: For P0we i Supply
use UL listed or I Cord: use UL
CSA approved I l!sted power
condu t sUpp!y cord kit
c°nnect°r t0 I marked fo r use
fit 7/8(2:2 Cm) with d!shwashe r
hoe
..................................................................................................................................................................................................................................................................iiiiiiiii;i;il,i,,,i,i,i,,,,,i_iil,iii¸;ii,lii¸;ii,lii¸;ii,lii¸;ii,lii¸;ii,lii¸;ii,lii¸;ii,lii¸;ii,lii¸;il,i,i_;ii;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;i
Location Requirements
Grounded electrical supply required.
Do not run drain lines, water lines or electrical wiring where
they can interfere with or contact dishwasher motor or legs.
The location where the dishwasher will be installed must
provide clearance between motor and flooring. Motor
should not touch the floor.
Do not install dishwasher over carpeted flooring.
Protect dishwasher and water lines leading to dishwasher
against freezing. Damage from freezing is not covered by
the warranty.
A side panel kit is available from your dealer for installing
your dishwasher at the end of your cabinetry.
A moisture barrier accessory (Part No. 4396277) is available
from your dealer for installing underneath the countertop,
but is not required.
Check location where dishwasher will be installed. The
location must provide:
, easy access to water, electricity and drain.
, convenient access for loading and unloading dishes.
Corner locations require a 2" (5.1 cm) minimum
clearance between the side of the dishwasher door
and the wall or cabinet.
, square opening for proper operation and appearance.
, cabinet front perpendicular to floor.
, level floor. (If floor at front of opening is not level with
floor at rear of opening, shims may be needed to level
dishwasher.)
Helpful Tip: Be sure to accurately measure dimensions
and ensure dishwasher is level if the floor in the
dishwasher opening is uneven (example: flooring
extends only partway into opening).
NOTE: To prevent shifting during dishwasher operation,
shims must be securely attached to the floor.
If dishwasher will be left unused for a period of time or in a
location where it may be subject to freezing, have it
winterized by authorized service personnel.
Make sure pipes, wires and drain hose are within the
shaded area shown in the "Product and Cabinet
Opening Dimensions" section. 3
*Insulation may
be compressed.
(not used on all models)
NOTE: Shaded area of cabinet walls show where
utility connections may be installed.
*Measured from the lowest point on the
underside of countertop. May be reduced to
33-7/8" (86 cm) by removing wheels from
dishwasher,
**Minimum, measured from narrowest point of
opening.
Check that all surfaces
have no protrusions that would
prevent dishwasher installatibn
4
Drain Requirements
, A new drain hose is supplied with your dishwasher.
If this is not long enough, use a new drain hose with a
maximum length of 12' (3.7 m) (Part No. 3385556) that
meets all current AHAM/IAPMO test standards, is resistant
to heat and detergent, and fits the 1" (2.5 cm) drain
connector of the dishwasher.
, Make sure to connect drain hose to waste tee or disposer
inlet above drain trap in house plumbing and 20" (50.8
cm) minimum above the floor. It is recommended that
the drain hose either be looped up and securely fastened
to the underside of the counter, or be connected to an
air gap.
, Make sure to use an air gap if the drain hose is connected
to house plumbing lower than 20" (50.8 cm) above
subfloor or floor.
, Use 1/2" minimum I.D. drain line fittings.
, If required the air gap should be installed in accordance
with the air gap installation instructions, when connecting
the air gap a rubber hose (not provided) will be needed to
connect to the waste tee or disposer inlet.
Wafer Supply Requirements
, A hot water line with 20-120 psi (138-862 kPa) water
pressure can be verified by a licensed plumber.
, 120°F (49°C) water at dishwasher.
,3/8" O.D. copper tubing with compression fitting or
flexible braided water supply line (Part No. 4396897RP)
NOTE: 1/2" minimum plastic tubing is not recommended.
, A 90° elbow with 3/8" N.RT. external pipe threads on one
end.
, Do not solder within 6" (15.2 cm) from water inlet valve.
ElectricalRequirements
Be sure that the electrical connection and wire size are
adequate and in conformance with the National Electrical
Code, ANSl/NFPA 70 - latest edition and all local codes and
ordinances.
A copy of the above code standards can be obtained from:
National Fire Protection Association
One Batterymarch Park
Quincy, MA 02269
You must have:
, 120-volt, 60 Hz, AC-only, 15 or 20 amp., fused electrical
supply.
, copper wire only.
We recommend:
, a time-delay fuse or circuit breaker.
, a separate circuit.
if connecting dishwasher
with a power supply cord:
, Use UL listed power supply cord kit (Part No. 4317824)
marked for use with dishwasher.
, Power supply cord must plug into
a grounded 3 prong outlet, located in
the cabinet next to the dishwasher
opening. Outlet must meet all local
codes and ordinances.
if connecting dishwasher with direct wiring:
, Use flexible, armored
or non-metallic
sheathed, copper wire
with grounding wire
that meets the wiring requirements for your home and
local codes and ordinances.
, Use a U.L. listed or CSA approved conduit connector.
Electrical Shock Hazard
Disconnect electrical power at the fuse box or circuit
breaker box before installing dishwasher.
Failure to do so can resuR in death or electrical shock.
oa ....
Disconnec t electrical power at the fuS e boxor drCU!t
breaker box before instal!ing dishwasher,
LShoiofiihe tOihodish a hei:
Yes _EO!low instructions in the "P[ePare Cabinet
Opening_Exist!ng Utilities" Secti0nl
NO _FoHow inStruCtions in the !'Prepare Cabinet
Opening_New Utilities" Sectionl
hookups ity hookups
6
Prepare Cabinet OpeningmExisting
Utilities
Cable
If the water line and the cable extend to the locations
shown, proceed to the "Install Drain Hose" section. If they
do not reach far enough, follow the instructions in the
"Prepare Cabinet Opening--New Utilities" section.
_;_;_;_;_;_????_:_??_1_?_1_?_1_?_1_?_1_?_1_?_11_1_??_:_??_1_?_1_?_1_?_1_?_1_?_;1_{{_;_;;_;_;_;__:_ii_i;i_i_i;i;;ii;_;i;;ii;_;_;i_ii_:_ii_ii_:_ii_i{_ii,:,i:_i_i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;i;i:_ii_ii;;i;i:_ii_ii;;i;i:_ii_ii;;i;i:_ii_ii;;i;i:_ii_ii{_:_ii_i;_;i{_i;_;_;i_ii_ii_i{_ii,i:_i_i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;_;i_ii;i_i;i;;i;i:_i_i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;
Prepare Cabinet OpeningmNew
Utilities
Prepare and route the electrical supply
Direct Wire:
_ _ Follow Option B instructions
Option A, Power Supply Cord:
NOTE: A grounded 3 prong outlet is required inside a
cabinet next to the dishwasher cabinet opening.
Drill a 1-1/2" (3.8 cm) hole in cabinet side or rear.
See product and cabinet opening dimensions.
Woodcabinet:Sandholeuntilsmooth.
Metalcabinet:Coverholewithgrommetincludedwith
powersupplycordkit.
OptionB, Direct Wire:
Helpful Tip: Wiring the dishwasher will be easier if you
route the cable into the cabinet opening from the right side.
Drill a 3/4" (1.9 cm) hole in right-hand cabinet side or rear.
See product and cabinet opening dimensions.
Wood cabinet: Sand hole until smooth.
Metal cabinet: Cover hole with grommet (not provided).
Route cable from power supply through cabinet hole (cable
must extend to the right front side of cabinet opening).
Tape cable to the floor in area shown. This will prevent
cable from moving when dishwasher is moved into
cabinet opening.
Prepare and Route Wafer Line
Helpful Tip: Routing the water line through the left side
of cabinet opening will make water connection easier.
Drill a 1/2" (1.3 cm) hole in the cabinet side or rear.
Measure overall length of copper tubing or flexible
braided water supply line. Attach to the hot water line
using a connection configuration that is in compliance
with local codes and ordinances. The water line to the
dishwasher should have a manual shutoff valve.
Slowlyroutewatersupplylinethroughholeincabinet.
(Ifusingcoppertubing,itwillbendandkinkeasily,sobe
gentle.)Itshouldbefarenoughintothecabinetopening
toconnectittothedishwasherinletonthefrontleft
sideofthedishwasher.
Slowlyturnwatershutoffvalveto "ON"position.Flush
waterintoashallowpanuntilcleartogetridofparticles
thatcouldclogtheinletvalve.Turnshutoffvalveto
"OFF"position.
Ifneeded,drilla1-1/2"(3.8cm)diameterholeincabinet
wallorsideoftheopeningclosesttothesink.
8
Routedrainhoseasshownthroughholeincabinettothe
frontcenterofopeningwheredrainconnectionwillbe
made.Tapedrainhosetothefloorinareashown.Thiswill
preventitfrommovingwhendishwasherismovedinto
cabinetopening.
_Opti0nB,Nowastedisposer_noairgap
,OptionCtWastedisposer-withairgap
' opti0nD_NowastediSP0se[_Withairgap
IMPORTANT:Thedrainhoseconnectionofthedisposeror
awasteteemustbemadebeforethedraintrapandat
least20"(50.8cm)abovethefloorwherethedishwasher
willbeinstalled.
HelpfulTip:Toreducevibrationofthehose,keepthehose
awayfromthefloor.
OptionA,Wastedisposer- no air gap
__;_i!{_;;_j__i__<_ i_;;?;;;;;¢_;{_i: $; _
1. Using a hammer and screwdriver,
knock plug into disposer.
2. Use needle nose pliers to remove
plug.
3. Attach drain hose to disposer inlet
with large silver drain hose clamp
(provided). Use pliers to squeeze
clamp open and move into position.
Option B, No waste disposer - no air gap
1.Connect black end of of drain hose to
waste tee and cut if needed.
(Do not cut ribbed section.)
2. Attach black end of drain hose to waste
tee with a large silver drain hose clamp
(provided). Use pliers to squeeze clamp
open and move into position. Ifthe drain
hose was cut use a 1-1/2" to 2" (3.8 to 5
cm) screw-type clamp (not provided).
Option C, Waste disposer - with air gap
Drain trap
1. Using a hammer and screwdriver,
knock plug into disposer.
2. Use needle nose pliers to remove
plug.
3. Connect black end of drain hose to air
gap and cut if needed. (Do not cut
ribbed section.)
4,
5.
Attach drain hose to air gap with large
silver drain hose clamp (provided).
Use pliers to squeeze clamp open and
move into position. If the drain hose
was cut, use a 1-1/2" to 2"(3.8 to 5
cm) screw-type clamp (not provided).
Use a rubber hose (not provided) with
screw-type clamps (not provided) to
connect from air gap to disposer inlet.
Option D, No waste disposer - with air gap
2,
3.
Connect black end of drain hose to air
gap and cut if needed. (Do not cut
ribbed section.)
Attach drain hose to air gap with large
silver drain hose clamp (provided).
Use pliers to squeeze clamp open and
move into position. If the drain hose
was cut, use a 1-1/2" to 2"(3.8 to 5 cm)
screw-type clamp (not provided).
Use a rubber hose (not provided) with
screw-type clamps (not provided) to
connect from waste tee to air gap.
Prepare Dishwasher
Tip Over Hazard
Do not use dishwasher until completely installed.
Do not push down on open door.
Doing so can result in serious injury or cuts.
Excessive Weight Hazard
Use two or more people to move and install
dishwasher.
Failure to do so can result in back or other injury.
Put dishwasher on its back
Helpful Tip: Place cardboard under dishwasher until installed
in cabinet opening to avoid damaging floor covering. Do not
use door panel as a work table without first covering with a
towel to prevent scratching the door panel.
Using two or more people, grasp sides of dishwasher door
frame and place dishwasher on its back.
Using a 1/4" hex head socket, nut driver or Phillips
screwdriver, remove two screws attaching access panel
and lower panel to dishwasher. Do not remove tech
sheet from access panel.
10
Apply Teflon ® tape or pipe joint compound to 90 ° elbow
fitting (not provided). Wrap tape around coarse threads
two to four times to prevent leaks.
Connect 90° elbow fitting to water inlet valve. Using a
wrench, tighten elbow until snug, and be sure that it
faces to the rear.
Using a 1/4" hex head socket, nut driver or Phillips
screwdriver, remove terminal box cover. Retain for
later use.
0
Install a U.L. listed or CSA approved conduit connector.
Make sure screwheads are facing to the left when tightening
conduit nut. Conduit connector may be provided with the
power supply cord kit.
What type of electrical
connection will you use?
Power Supply Cord:
Follow Option A instructions
Direct Wi re:
Follow Option B instructions
Make Power Supply Cord Connection
Option A, Power Supply Cord:
Route cord so that it does not touch dishwasher motor
to lower part of dishwasher tub. Pull cord through
conduit connector in terminal bow.
Select UL listed or CSA approved twist-on wire connectors
(not included) rated to connect your household wiring to
16-gauge dishwasher wiring.
Electrical Shock Hazard
Electrically ground dishwasher.
Connect ground wire to green ground connector
in terminal box.
Do not use an extension cord.
Failure to follow these instructions can result in
death, fire, or electrical shock.
Remove the green grounding screw and place through
the ring terminal of the green ground wire. Reattach and
tighten the green screw.
NOTE: Do not pre-twist stranded wire. Twist on wire
connector. Gently tug on wires to be sure both are
secured.
Connect wires black to black and white to white, using
UL listed or CSA approved twist-on wire connectors (not
included).
11
iiii_ii_i_iiiii_ii`_i_i_ii_iiii1iiiii1iiii1i_iiiiiii_iiiiii11iiiii_iiiiiiii_iiiiiiii_iiiiif_i_iiii_`_`_i_ii1ii_iiii_i_i_iiiiii1ti_ii_ii1ii_ii1ii_ii1ii_ii1ii_i_i_ii1iii_iii1tiiiiii_i````````````````````````````````````````````````````````````````````````````````````````i`_iii_!i`i!_i!_!i_ii_iiii_iiiiiiiii_iiiiiiii_iiiiiiiiii_i_¸il¸ii_iiiii1i_i_iiiiiiiiiiii11i_ii_ii1ii_i_iiiiiiiiiiiiii_iiiiii11i_ii1iiiiiiiiiiiiiii_iiiiiiiiIiIiiii_ii_Iiti_ii_Iiti_ii_Iiti_ii_Iiti_ii_11iiiiiiiiii
Defermine Cabinef Opening
ground wire _ ground connector
If needed, see website for animated representation of
this step. Visit www.whiHpooLcom under FAQ tab.
Tighten conduit connector screws to secure cord.
Place wires inside terminal box. Insert tabs on left side
of cover. Make sure wires are tucked inside box. Close
cover ensuring wires are not pinched. Use 1/4" nut
driver and previously removed screw to secure cover.
NOTE: Do not plug into outlet until instructed.
Measure height of cabinet opening from underside of
countertop to floor where dishwasher will be installed
(you will need to measure the lowest point on the
underside of the countertop and the highest point on the
floor). Refer to "Dishwasher Height Adjustment Chart"
for wheel position and the number of turns needed.
Dishwasher Height Adjustment Cha
i
Cabinet Wheel Number of turns
opening height position i on front leg
I
33;7/8" (86.0 cm) Removed A!l the way up
t,"
34 (8&4cm) : 1 ! 10
34-'1/4 (87 cm) 2 5
34-1/2" (87.6 cm) 3 , 0
,.#
NOTE: If the minimum cabinet opening height is less than
34"(86.4 cm), the rear wheels can be removed for
additional clearance. This will allow the dishwasher to fit
into a 33-7/8" (86 cm) high cabinet opening, but the
dishwasher will be more difficult to move. (Measurements
are approximate. Wheels and legs are preset at the
factory for 34-1/2" (87.6" cm).)
Adjust wheels and legs
i_I ixiiiiiiiiiiiiiiiiiiiiiii'
Turn both leveler legs to the same height. Put wheels in
the required position determined from "Dishwasher
Height Adjustment Chart". (To change wheel position,
use a flat bladed screwdriver to pop out the wheel, then
snap into the new position.)
12
Built-upfloors(Kitchenfloorheightishigherthan
cabinetopening.)Example:Kitchenfloortiledoesnot
extendintocabinetopening.Addshimsasneededinthe
areashowntobringthedishwasherupto34"(86.4cm)
belowthecountertop.
NOTE:Shimsmustbesecurelyattachedtofloorto
preventmovementwhenthedishwasherisinuse.
Move Dishwasher into Cabinet
Opening
Using two or more people, stand dishwasher upright.
NOTE: Do not install kickplate until instructed.
Move dishwasher close to
cabinet opening
IMPORTANT: Double check correct placement of utilities.
Grasp the sides of the dishwasher at the edges of the
door panel. Tilt dishwasher backwards on wheels and
move dishwasher close to cabinet opening.
NOTE: Do not push on the front of the panel or on the
console-they may dent.
Helpful Tip: Temporarily tape utilities to the floor in the
locations shown to prevent them from moving when
dishwasher is moved into the cabinet opening.
Check that water line is on the left side of opening and
drain hose is near the center of the cabinet opening,
With another person holding the dishwasher to prevent
it from tipping, open and close the door a few times. If
the door closes or falls open under its own weight, the
door tension will need to be adjusted. 13
Ifthedoorclosestooquickly,decreasethespring
tensionbymovingthespringendtowardthefrontof
thedishwasher.
NOTE:Springsshouldbeinthesamenotchesonleft
andrightsides.
Ifthedoorfallsopen,increasethespringtensionby
movingthespringendtowardthebackofthe
dishwasher.
NOTE:Springsshouldbeinthesamenotchesonleft
andrightsides.
14
Move dishwasher into
cabinet opening
IMPORTANT: If wheels were removed, protect the floor
when moving the dishwasher. Slowly move dishwasher
completely into cabinet opening. Do not kink or pinch
water line, drain hose, power supply cord or direct wire
between dishwasher and cabinet. Remove cardboard
from under dishwasher.
NOTE: It is all right if dishwasher fits tightly into cabinet
opening. Do not remove insulation blanket- the blanket
reduces the sound level.
NOTE: If using power cord, make sure to route end
through hole in cutout before sliding into cabinet opening.
Align front of dishwasher door panel with front of
cabinet doors. You may need to adjust alignment to be
even with your cabinets.
Check that leveling legs are firmly against the floor.
Close and latch the door, and place level against the
front panel. Check that dishwasher is centered from front
to back in the opening. If needed, adjust leveling leg until
dishwasher is plumb. Repeat for other side of dishwasher.
HelpfulTip:Pushuponfrontofdishwashertoraise
dishwasheroffthegroundtoadjustfrontlegs.With
someinstallations,it maybeeasiertoadjustthefrontleg
usingthe3/16"hexheadsocketoradjustablewrench.
Placelevelagainsttopfrontopeningoftub.Checkthat
dishwasherislevelfromsidetoside.Ifdishwasherisnot
level,adjustfrontlegsupordownuntildishwasheris
level.
Coppertubingonly:Slidenutthenferruleontocopper
tubingabout1"(2.5cm).
NOTE:Topreventvibrationduringoperation,routethe
watersupplylinesothatitdoesnottouchthe
dishwasherbase,frameormotor.
Coppertubingonly:Putthetubingintothe90°elbow
fittingasfarasitwillgo(thecoppertubingbendsand
kinkseasily).Slidethenutandferruleforwardandstart
thenutontotheelbowthreads.
Flexiblebraidedconnection:Securenuttoelbowusing
5/8"openendedwrenchoradjustablewrench.
NOTE:DonotuseTeflon®tapewithcompressionfittings.
Holdthe90°elbowfittingstillwithoneadjustablewrench
andtightenthenutwithsecondadjustablewrench.
Helpful Tip: Use a 5/8 open ended wrench for easier
access to tighten connection.
Place paper towel under 90 ° elbow fitting. Turn on water
supply and check for leaks. If leak occurs, repeat
previous step.
If needed, see website for animated representation
of this step. Visit www.whirlpool.eom/watersupply
under FAQ tab.
15
iiiiif_i_if_i_if_i_if_i_ii_i_iii_i_iii_i_i_i_iiii_i_iii_i_iii_i_iii_i_iii_i_iii_i_iii_i_iii_i_iii_i_iii_i_ii_i_ii_iii_i_iii_ii_iiiiiii_ii_iii_ii_iii_i_ii_i_ii_i_iiiii_i_iiiIiiiii:;i;;ii;:;i;;ii_ii;;ii;:;i;;i;;ii;;;i;;ii;ii_ii;;ii;:;i;;ii;:;:;i;;ii_i_iiii11iii_tiiiiiiiiiii_i}iiii_;_ii}iiii_;_ii}iiii_;_ii}iiii_;_ii}iiii_;_ii}iiii_;_ii}iiii_;_ii}iiii_;_ii}iiii_;_ii}iiii_;_ii}iiii_;_ii}iiii_;_ii}iiii_;_ii}iiii_;_ii}iiii_;_ii}iiii_;_ii}iiii_;_ii}iiii_;_ii}iiii_;_ii}iiii_;_ii}iiii_;_ii}ii}iiiiii_;i_iiiiiiiiiiiiiB
Connect to Drain
Black drain hose
Green clam
Sto p
Drain hose
Drain hose stop
Place towel under drain hose to catch any water in drain
hose. Place the small green drain hose clamp onto the
small end of the drain hose. Push the new drain hose
into the black drain hose connector up to the drain hose
stop.
Using pliers, squeeze open the small green drain hose
clamp and slide onto connector between stops.
Once connected, remove towel.
If needed, see website for animated representation of
this step. Visit www.whirlpool.com/drain under FAQ tab.
Make DirectWire Electrical
Connection
NOTE: If the power supply cord was connected earlier
proceed to Secure Dishwasher in Cabinet Opening
section.
Option B, Direct Wire:
Route cable so that it does not touch dishwasher motor
or lower part of dishwasher tub. Pull cable through cable
clamp in terminal box.
Select UL listed or CSA approved twist-on wire connectors
(not included) rated to connect your household wiring to
16-gauge dishwasher wiring.
16
ElectricalShock Hazard
Electrically ground dishwasher.
Connect ground wire to green ground connector
in terminal box.
Do not use an extension cord.
Failure to follow these instructions can result in
death, fire, or electrical shock.
I !7i\ +
I 1%-C-LI) f-r_.."_ll--Oround i
ILl wire c # L_/_lr7 d TM
=sh
Ground
Form bare ground wire into a U-shaped hook. Wrap
ground wire hook clockwise around ground connector
screw and under the washer. Securely tighten ground
connector.
NOTE: Twist on UL listed or CSA approved wire
connector. Gently tug on wires to be sure both are
secured.
Connect wires black to black and white to white, using
UL listed or CSA approved twist-on wire connectors (not
included).
)
If needed, see website for animated representation
of this step. Visit www.whirlpool.eom/eleetrical under
FAQ tab.
Tighten conduit connector screws to secure cable.
Place wires inside terminal box. Insert tabs on left side
of cover. Make sure wires are tucked inside box. Close
cover ensuring wires are not pinched. Use 1/4" nut
driver and previously removed screw to secure cover.
17
Checkthatdishwasherisstilllevelfrontto backandside
tosideincabinetopening.
IMPORTANT: If you have solid countertops such as
corrian, granite, etc., you must use side mounting kit
(Part No. 8212560). Follow kit instructions. (Brackets
included with kit.)
Open dishwasher door, remove lower dish rack, and
place towel over pump assembly and lower spray arm of
dishwasher. This will prevent screws from falling into
pump area when securing dishwasher to countertop.
NOTE: Do not drop screws into bottom of dishwasher.
Locate brackets on top of dishwasher and secure
dishwasher to countertop with two, #10 x 1/2" phillips-
head screws (included). The dishwasher must be secured
to keep it from shifting when door is opened.
Check that top of door does not contact screws,
brackets, or countertop. If it does, adjust leveling legs.
Open door and check that space between dishwasher
cabinet opening and tub is equal on both sides. If
spacing is not equal, loosen bracket screws secured
and shift tub. Tighten bracket screws.
18
Removetowelfromdishwasher.Reinstallthelower
dishrack.
If needed, see website for animated representation
of this step. Visit www.whirlpool.eom/anchoring under
FAQ tab.
Check that grounding clip is attached to the lower panel.
Position the lower panel behind the access panel. On some
models there is insulation on the access panel which must
fall behind the insulation on the lower panel.
Hold the two panels together and place them against
dishwasher leg. Using a philips or 1/4" screwdriver, reinstall
the screws through the holes in the access panel and the
slots in the lower panel.
Check that the lower edge of the lower panel contacts
the floor. Adjust if necessary.
Tighten access panel screws.
TEFLON is a registered trademark of E.I. Du Pont
De Nemours and Company.
19
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result
in death, fire, or electrical shock.
Plug into a grounded 3 prong outlet. Check that power
supply cord does not touch dishwasher motor or lower
part of dishwasher tub.
Reconnect Power
Check Operation
[_ Read the Dishwasher User Instructions that came
with your dishwasher.
[_ Check that all parts have been installed and no steps
were skipped. Check that you have all tools used.
[_ Start dishwasher and allow it to complete the shortest
wash cycle. After the first 2 minutes unlatch door,
wait 5 seconds, then open door. Check to see that
there is water in the bottom of the dishwasher tub.
Check that dishwasher is working properly.
If not, disconnect power or unplug dishwasher and
see "If Dishwasher Does Not Operate" section.
Has the circuit breaker tripped or the house fuse
blown?
Is the door closed tightly and latched?
Has the cycle been set correctly to start the
dishwasher?
Is the water turned on?
If none of these work, call 1-800-253-1301, or in Canada,
call 1-800-807-6777.
For Roper models, call 1-800-447-6737, or in Canada call
1-800-807-6777.
Additional Tips
Expect longer wash times. Your new dishwasher will
average 2-3 hours per load, but use nearly 40% less
energy than older models. Designed with a low wattage,
low energy consumption motor, your dishwasher
washes longer to ensure exceptional cleaning. Certain
models are equipped with an optical water sensor so the
first cycle will run longer to calibrate to optical sensor.
Selecting certain options could increase cycle time past
3.5 hours.
Rinse Aid is necessary for good drying results:
This dishwasher is designed to be used with rinse aid for
good drying performance and controlling hard water
deposit build-up. Energy efficient dishwashers use less
water and energy so they depend on the water sheeting
action of rinse aid for good drying performance.
Start/Resume light may flash:
When pressing Start/Resume, you must make sure the
door is closed within 3 seconds. If you do not, the
Start/Resume light will flash until you press it again.
(You must also do this when adding a dish during the
middle of a cycle.)
20 © 2007 All rights reserved
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39

Estate TUD8700WD1 Guide d'installation

Catégorie
Lave-vaisselle
Taper
Guide d'installation

dans d''autres langues