Inglis GU2300XTVS1 Guide d'installation

Marque: Inglis

Modèle: GU2300XTVS1

Catégorie: Lave-vaisselle

Taper: Guide d'installation

INSTALLATION iNSTRUCTiONS

UNDERCOUNTER DISHWASHER

PLASTIC GIANT TUBMODELS

iNSTRUCTiONS D'INSTALLATION

LAVE--VAISSELLEENCASTRE

MODELES A TRESGRANDE CUVE EN PLASTIQUE

Table of Contents ................................... 2

Table des matieres .................................. 21

W10142914

Table of Contents

Dishwasher Safety ................................. 2

Installation Requirements ........................... 3

Tools and Parts ................................... 3

Location Requirements ............................ 3

Drain Requirements ............................... 5

Water Supply Requirements ........................ 5

Electrical Requirements ............................ 5

Installation Instructions ............................. 6

Prepare Cabinet Opening--Existing Utilities ........... 6

Prepare Cabinet Opening--New Utilities .............. 6

Prepare and Route Water Line ...................... 7

Install Drain Hose ................................ 8

Installation Instructions (cont.).........................

Prepare Dishwasher ............................. 10

Make Power Cord Electrical Connection ............. 11

Determine Cabinet Opening ....................... 12

Move Dishwasher into Cabinet Opening ............. 13

Connect to Water Supply ......................... 15

Connect to Drain ................................ 16

Make Direct Wire Electrical Connection .............. 16

Secure Dishwasher in Cabinet Opening ............. 18

Complete Installation ............................. 19

Check Operation ................................. 20

If Dishwasher Does Not Operate ................... 20

Additional Tips .................................. 20

DISHWASHERSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured ifyou don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Doing so can result in serious injury or cuts.

You Need to:

Slowly open dishwasher door while someone grasps the

rear of the dishwasher. Remove shipping materials, drain

hose and lower rack. Close dishwasher door until latched.

Observe all governing codes and ordinances.

Install this dishwasher as specified in these instructions.

Installation should be performed by a qualified service

technician. The dishwasher must be installed to meet all

electrical and plumbing national and local codes and

ordinances.

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the recommended tools and parts before starting

installation. Read and follow the instructions provided with

any tools listed here.

All installations

Tools needed:

IFlat-blode

Fliers I screwdriver

5/16" and 1/4" _ UL listed or CSA _ n

nut drivers or _7" approved twist-on U U

hex sockets _,_" wire connectors*

ii -

10 adjustable wrench 5 8" o_en end

/ F -

that opens to wrench _

1-1.8" (2.9 cm) U =' _ ,

*Must be the proper size to connect your household wiring

to 16-gauge wiring in dishwasher

Other useful items you may need:

4 ?

Fos,oht othtowo

Parts supplied:

12 !Drain hOseclamp__ Drai_ [ 2 _#10xli2.

PhillipsLhead

(!,a,_,,d l_a 1) screws

Silver Green [

Make sure all these parts are included in the literature package.

Parts needed:

90tiEIb0w fitting with Teflon® tape or pipe joint

3/8 N:P.T. external threads compound

(the 0the[ end mus t fit you i

water suDulv line) ( _ _. "_

Other parts you may also need:

I s,0o,,tctto e

(38:1-5 0 cm) I for solid surface I du

screw4ype c0untertops @

camps{3max) J PartNo.8212560

NOTE: Parts available for purchase in plumbing supply stores.

Check local codes. Check existing electrical supply. See

"Electrical Requirements" section. It is recommended that

electrical connections be made by a licensed electrical installer.

® Teflon is a registered trademark of E.I. Du Pont de Nemours and Company.

In addition, for first time installations

Tools needed:

Parts needed:

Copper tubing (3/8"

O.D, suggested) or

flexible braided

water Supply line

See "Electrical Requirements" section

Foi Direct Wire: For P0we i Supply

use UL listed or I Cord: use UL

CSA approved I l!sted power

condu t sUpp!y cord kit

c°nnect°r t0 I marked fo r use

fit 7/8(2:2 Cm) with d!shwashe r

hoe

..................................................................................................................................................................................................................................................................iiiiiiiii;i;il,i,,,i,i,i,,,,,i_iil,iii¸;ii,lii¸;ii,lii¸;ii,lii¸;ii,lii¸;ii,lii¸;ii,lii¸;ii,lii¸;ii,lii¸;il,i,i_;ii;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;ii¸;i;i

Location Requirements

Grounded electrical supply required.

Do not run drain lines, water lines or electrical wiring where

they can interfere with or contact dishwasher motor or legs.

The location where the dishwasher will be installed must

provide clearance between motor and flooring. Motor

should not touch the floor.

Do not install dishwasher over carpeted flooring.

Protect dishwasher and water lines leading to dishwasher

against freezing. Damage from freezing is not covered by

the warranty.

A side panel kit is available from your dealer for installing

your dishwasher at the end of your cabinetry.

A moisture barrier accessory (Part No. 4396277) is available

from your dealer for installing underneath the countertop,

but is not required.

Check location where dishwasher will be installed. The

location must provide:

, easy access to water, electricity and drain.

, convenient access for loading and unloading dishes.

Corner locations require a 2" (5.1 cm) minimum

clearance between the side of the dishwasher door

and the wall or cabinet.

, square opening for proper operation and appearance.

, cabinet front perpendicular to floor.

, level floor. (If floor at front of opening is not level with

floor at rear of opening, shims may be needed to level

dishwasher.)

Helpful Tip: Be sure to accurately measure dimensions

and ensure dishwasher is level if the floor in the

dishwasher opening is uneven (example: flooring

extends only partway into opening).

NOTE: To prevent shifting during dishwasher operation,

shims must be securely attached to the floor.

If dishwasher will be left unused for a period of time or in a

location where it may be subject to freezing, have it

winterized by authorized service personnel.

Make sure pipes, wires and drain hose are within the

shaded area shown in the "Product and Cabinet

Opening Dimensions" section. 3

*Insulation may

be compressed.

(not used on all models)

NOTE: Shaded area of cabinet walls show where

utility connections may be installed.

*Measured from the lowest point on the

underside of countertop. May be reduced to

33-7/8" (86 cm) by removing wheels from

dishwasher,

**Minimum, measured from narrowest point of

opening.

Check that all surfaces

have no protrusions that would

prevent dishwasher installatibn

Drain Requirements

, A new drain hose is supplied with your dishwasher.

If this is not long enough, use a new drain hose with a

maximum length of 12' (3.7 m) (Part No. 3385556) that

meets all current AHAM/IAPMO test standards, is resistant

to heat and detergent, and fits the 1" (2.5 cm) drain

connector of the dishwasher.

, Make sure to connect drain hose to waste tee or disposer

inlet above drain trap in house plumbing and 20" (50.8

cm) minimum above the floor. It is recommended that

the drain hose either be looped up and securely fastened

to the underside of the counter, or be connected to an

air gap.

, Make sure to use an air gap if the drain hose is connected

to house plumbing lower than 20" (50.8 cm) above

subfloor or floor.

, Use 1/2" minimum I.D. drain line fittings.

, If required the air gap should be installed in accordance

with the air gap installation instructions, when connecting

the air gap a rubber hose (not provided) will be needed to

connect to the waste tee or disposer inlet.

Wafer Supply Requirements

, A hot water line with 20-120 psi (138-862 kPa) water

pressure can be verified by a licensed plumber.

, 120°F (49°C) water at dishwasher.

,3/8" O.D. copper tubing with compression fitting or

flexible braided water supply line (Part No. 4396897RP)

NOTE: 1/2" minimum plastic tubing is not recommended.

, A 90° elbow with 3/8" N.RT. external pipe threads on one

end.

, Do not solder within 6" (15.2 cm) from water inlet valve.

ElectricalRequirements

Be sure that the electrical connection and wire size are

adequate and in conformance with the National Electrical

Code, ANSl/NFPA 70 - latest edition and all local codes and

ordinances.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park

Quincy, MA 02269

You must have:

, 120-volt, 60 Hz, AC-only, 15 or 20 amp., fused electrical

supply.

, copper wire only.

We recommend:

, a time-delay fuse or circuit breaker.

, a separate circuit.

if connecting dishwasher

with a power supply cord:

, Use UL listed power supply cord kit (Part No. 4317824)

marked for use with dishwasher.

, Power supply cord must plug into

a grounded 3 prong outlet, located in

the cabinet next to the dishwasher

opening. Outlet must meet all local

codes and ordinances.

if connecting dishwasher with direct wiring:

, Use flexible, armored

or non-metallic

sheathed, copper wire

with grounding wire

that meets the wiring requirements for your home and

local codes and ordinances.

, Use a U.L. listed or CSA approved conduit connector.

Electrical Shock Hazard

Disconnect electrical power at the fuse box or circuit

breaker box before installing dishwasher.

Failure to do so can resuR in death or electrical shock.

oa ....

Disconnec t electrical power at the fuS e boxor drCU!t

breaker box before instal!ing dishwasher,

LShoiofiihe tOihodish a hei:

Yes _EO!low instructions in the "P[ePare Cabinet

Opening_Exist!ng Utilities" Secti0nl

NO _FoHow inStruCtions in the !'Prepare Cabinet

Opening_New Utilities" Sectionl

hookups ity hookups

Prepare Cabinet OpeningmExisting

Utilities

Cable

If the water line and the cable extend to the locations

shown, proceed to the "Install Drain Hose" section. If they

do not reach far enough, follow the instructions in the

"Prepare Cabinet Opening--New Utilities" section.

_;_;_;_;_;_????_:_??_1_?_1_?_1_?_1_?_1_?_1_?_11_1_??_:_??_1_?_1_?_1_?_1_?_1_?_;1_{{_;_;;_;_;_;__:_ii_i;i_i_i;i;;ii;_;i;;ii;_;_;i_ii_:_ii_ii_:_ii_i{_ii,:,i:_i_i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;i;i:_ii_ii;;i;i:_ii_ii;;i;i:_ii_ii;;i;i:_ii_ii;;i;i:_ii_ii{_:_ii_i;_;i{_i;_;_;i_ii_ii_i{_ii,i:_i_i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;_;i_ii;i_i;i;;i;i:_i_i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;ii;_;i;;

Prepare Cabinet OpeningmNew

Utilities

Prepare and route the electrical supply

Direct Wire:

_ _ Follow Option B instructions

Option A, Power Supply Cord:

NOTE: A grounded 3 prong outlet is required inside a

cabinet next to the dishwasher cabinet opening.

Drill a 1-1/2" (3.8 cm) hole in cabinet side or rear.

See product and cabinet opening dimensions.

Woodcabinet:Sandholeuntilsmooth.

Metalcabinet:Coverholewithgrommetincludedwith

powersupplycordkit.

OptionB, Direct Wire:

Helpful Tip: Wiring the dishwasher will be easier if you

route the cable into the cabinet opening from the right side.

Drill a 3/4" (1.9 cm) hole in right-hand cabinet side or rear.

See product and cabinet opening dimensions.

Wood cabinet: Sand hole until smooth.

Metal cabinet: Cover hole with grommet (not provided).

Route cable from power supply through cabinet hole (cable

must extend to the right front side of cabinet opening).

Tape cable to the floor in area shown. This will prevent

cable from moving when dishwasher is moved into

cabinet opening.

Prepare and Route Wafer Line

Helpful Tip: Routing the water line through the left side

of cabinet opening will make water connection easier.

Drill a 1/2" (1.3 cm) hole in the cabinet side or rear.

Measure overall length of copper tubing or flexible

braided water supply line. Attach to the hot water line

using a connection configuration that is in compliance

with local codes and ordinances. The water line to the

dishwasher should have a manual shutoff valve.

Slowlyroutewatersupplylinethroughholeincabinet.

(Ifusingcoppertubing,itwillbendandkinkeasily,sobe

gentle.)Itshouldbefarenoughintothecabinetopening

toconnectittothedishwasherinletonthefrontleft

sideofthedishwasher.

Slowlyturnwatershutoffvalveto "ON"position.Flush

waterintoashallowpanuntilcleartogetridofparticles

thatcouldclogtheinletvalve.Turnshutoffvalveto

"OFF"position.

Ifneeded,drilla1-1/2"(3.8cm)diameterholeincabinet

wallorsideoftheopeningclosesttothesink.

Routedrainhoseasshownthroughholeincabinettothe

frontcenterofopeningwheredrainconnectionwillbe

made.Tapedrainhosetothefloorinareashown.Thiswill

preventitfrommovingwhendishwasherismovedinto

cabinetopening.

_Opti0nB,Nowastedisposer_noairgap

,OptionCtWastedisposer-withairgap

' opti0nD_NowastediSP0se[_Withairgap

IMPORTANT:Thedrainhoseconnectionofthedisposeror

awasteteemustbemadebeforethedraintrapandat

least20"(50.8cm)abovethefloorwherethedishwasher

willbeinstalled.

HelpfulTip:Toreducevibrationofthehose,keepthehose

awayfromthefloor.

OptionA,Wastedisposer- no air gap

__;_i!{_;;_j__i__<_ i_;;?;;;;;¢_;{_i: $; _

1. Using a hammer and screwdriver,

knock plug into disposer.

2. Use needle nose pliers to remove

plug.

3. Attach drain hose to disposer inlet

with large silver drain hose clamp

(provided). Use pliers to squeeze

clamp open and move into position.

Option B, No waste disposer - no air gap

1.Connect black end of of drain hose to

waste tee and cut if needed.

(Do not cut ribbed section.)

2. Attach black end of drain hose to waste

tee with a large silver drain hose clamp

(provided). Use pliers to squeeze clamp

open and move into position. Ifthe drain

hose was cut use a 1-1/2" to 2" (3.8 to 5

cm) screw-type clamp (not provided).

Option C, Waste disposer - with air gap

Drain trap

1. Using a hammer and screwdriver,

knock plug into disposer.

2. Use needle nose pliers to remove

plug.

3. Connect black end of drain hose to air

gap and cut if needed. (Do not cut

ribbed section.)

Attach drain hose to air gap with large

silver drain hose clamp (provided).

Use pliers to squeeze clamp open and

move into position. If the drain hose

was cut, use a 1-1/2" to 2"(3.8 to 5

cm) screw-type clamp (not provided).

Use a rubber hose (not provided) with

screw-type clamps (not provided) to

connect from air gap to disposer inlet.

Option D, No waste disposer - with air gap

Connect black end of drain hose to air

gap and cut if needed. (Do not cut

ribbed section.)

Attach drain hose to air gap with large

silver drain hose clamp (provided).

Use pliers to squeeze clamp open and

move into position. If the drain hose

was cut, use a 1-1/2" to 2"(3.8 to 5 cm)

screw-type clamp (not provided).

Use a rubber hose (not provided) with

screw-type clamps (not provided) to

connect from waste tee to air gap.

Prepare Dishwasher

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Doing so can result in serious injury or cuts.

Excessive Weight Hazard

Use two or more people to move and install

dishwasher.

Failure to do so can result in back or other injury.

Put dishwasher on its back

Helpful Tip: Place cardboard under dishwasher until installed

in cabinet opening to avoid damaging floor covering. Do not

use door panel as a work table without first covering with a

towel to prevent scratching the door panel.

Using two or more people, grasp sides of dishwasher door

frame and place dishwasher on its back.

Using a 1/4" hex head socket, nut driver or Phillips

screwdriver, remove two screws attaching access panel

and lower panel to dishwasher. Do not remove tech

sheet from access panel.

Apply Teflon ® tape or pipe joint compound to 90 ° elbow

fitting (not provided). Wrap tape around coarse threads

two to four times to prevent leaks.

Connect 90° elbow fitting to water inlet valve. Using a

wrench, tighten elbow until snug, and be sure that it

faces to the rear.

Using a 1/4" hex head socket, nut driver or Phillips

screwdriver, remove terminal box cover. Retain for

later use.

Install a U.L. listed or CSA approved conduit connector.

Make sure screwheads are facing to the left when tightening

conduit nut. Conduit connector may be provided with the

power supply cord kit.

What type of electrical

connection will you use?

Power Supply Cord:

Follow Option A instructions

Direct Wi re:

Follow Option B instructions

Make Power Supply Cord Connection

Option A, Power Supply Cord:

Route cord so that it does not touch dishwasher motor

to lower part of dishwasher tub. Pull cord through

conduit connector in terminal bow.

Select UL listed or CSA approved twist-on wire connectors

(not included) rated to connect your household wiring to

16-gauge dishwasher wiring.

Electrical Shock Hazard

Electrically ground dishwasher.

Connect ground wire to green ground connector

in terminal box.

Do not use an extension cord.

Failure to follow these instructions can result in

death, fire, or electrical shock.

Remove the green grounding screw and place through

the ring terminal of the green ground wire. Reattach and

tighten the green screw.

NOTE: Do not pre-twist stranded wire. Twist on wire

connector. Gently tug on wires to be sure both are

secured.

Connect wires black to black and white to white, using

UL listed or CSA approved twist-on wire connectors (not

included).

iiii_ii_i_iiiii_ii`_i_i_ii_iiii1iiiii1iiii1i_iiiiiii_iiiiii11iiiii_iiiiiiii_iiiiiiii_iiiiif_i_iiii_`_`_i_ii1ii_iiii_i_i_iiiiii1ti_ii_ii1ii_ii1ii_ii1ii_ii1ii_i_i_ii1iii_iii1tiiiiii_i````````````````````````````````````````````````````````````````````````````````````````i`_iii_!i`i!_i!_!i_ii_iiii_iiiiiiiii_iiiiiiii_iiiiiiiiii_i_¸il¸ii_iiiii1i_i_iiiiiiiiiiii11i_ii_ii1ii_i_iiiiiiiiiiiiii_iiiiii11i_ii1iiiiiiiiiiiiiii_iiiiiiiiIiIiiii_ii_Iiti_ii_Iiti_ii_Iiti_ii_Iiti_ii_11iiiiiiiiii

Defermine Cabinef Opening

ground wire _ ground connector

If needed, see website for animated representation of

this step. Visit www.whiHpooLcom under FAQ tab.

Tighten conduit connector screws to secure cord.

Place wires inside terminal box. Insert tabs on left side

of cover. Make sure wires are tucked inside box. Close

cover ensuring wires are not pinched. Use 1/4" nut

driver and previously removed screw to secure cover.

NOTE: Do not plug into outlet until instructed.

Measure height of cabinet opening from underside of

countertop to floor where dishwasher will be installed

(you will need to measure the lowest point on the

underside of the countertop and the highest point on the

floor). Refer to "Dishwasher Height Adjustment Chart"

for wheel position and the number of turns needed.

Dishwasher Height Adjustment Cha

• i

Cabinet Wheel Number of turns

opening height position i on front leg

33;7/8" (86.0 cm) Removed A!l the way up

t,"

34 (8&4cm) : 1 ! 10

34-'1/4 (87 cm) 2 5

34-1/2" (87.6 cm) 3 , 0

,.#

NOTE: If the minimum cabinet opening height is less than

34"(86.4 cm), the rear wheels can be removed for

additional clearance. This will allow the dishwasher to fit

into a 33-7/8" (86 cm) high cabinet opening, but the

dishwasher will be more difficult to move. (Measurements

are approximate. Wheels and legs are preset at the

factory for 34-1/2" (87.6" cm).)

Adjust wheels and legs

i_I ixiiiiiiiiiiiiiiiiiiiiiii'

Turn both leveler legs to the same height. Put wheels in

the required position determined from "Dishwasher

Height Adjustment Chart". (To change wheel position,

use a flat bladed screwdriver to pop out the wheel, then

snap into the new position.)

Built-upfloors(Kitchenfloorheightishigherthan

cabinetopening.)Example:Kitchenfloortiledoesnot

extendintocabinetopening.Addshimsasneededinthe

areashowntobringthedishwasherupto34"(86.4cm)

belowthecountertop.

NOTE:Shimsmustbesecurelyattachedtofloorto

preventmovementwhenthedishwasherisinuse.

Move Dishwasher into Cabinet

Opening

Using two or more people, stand dishwasher upright.

NOTE: Do not install kickplate until instructed.

Move dishwasher close to

cabinet opening

IMPORTANT: Double check correct placement of utilities.

Grasp the sides of the dishwasher at the edges of the

door panel. Tilt dishwasher backwards on wheels and

move dishwasher close to cabinet opening.

NOTE: Do not push on the front of the panel or on the

console-they may dent.

Helpful Tip: Temporarily tape utilities to the floor in the

locations shown to prevent them from moving when

dishwasher is moved into the cabinet opening.

Check that water line is on the left side of opening and

drain hose is near the center of the cabinet opening,

With another person holding the dishwasher to prevent

it from tipping, open and close the door a few times. If

the door closes or falls open under its own weight, the

door tension will need to be adjusted. 13

Ifthedoorclosestooquickly,decreasethespring

tensionbymovingthespringendtowardthefrontof

thedishwasher.

NOTE:Springsshouldbeinthesamenotchesonleft

andrightsides.

Ifthedoorfallsopen,increasethespringtensionby

movingthespringendtowardthebackofthe

dishwasher.

NOTE:Springsshouldbeinthesamenotchesonleft

andrightsides.

Move dishwasher into

cabinet opening

IMPORTANT: If wheels were removed, protect the floor

when moving the dishwasher. Slowly move dishwasher

completely into cabinet opening. Do not kink or pinch

water line, drain hose, power supply cord or direct wire

between dishwasher and cabinet. Remove cardboard

from under dishwasher.

NOTE: It is all right if dishwasher fits tightly into cabinet

opening. Do not remove insulation blanket- the blanket

reduces the sound level.

NOTE: If using power cord, make sure to route end

through hole in cutout before sliding into cabinet opening.

Align front of dishwasher door panel with front of

cabinet doors. You may need to adjust alignment to be

even with your cabinets.

Check that leveling legs are firmly against the floor.

Close and latch the door, and place level against the

front panel. Check that dishwasher is centered from front

to back in the opening. If needed, adjust leveling leg until

dishwasher is plumb. Repeat for other side of dishwasher.

HelpfulTip:Pushuponfrontofdishwashertoraise

dishwasheroffthegroundtoadjustfrontlegs.With

someinstallations,it maybeeasiertoadjustthefrontleg

usingthe3/16"hexheadsocketoradjustablewrench.

Placelevelagainsttopfrontopeningoftub.Checkthat

dishwasherislevelfromsidetoside.Ifdishwasherisnot

level,adjustfrontlegsupordownuntildishwasheris

level.

Coppertubingonly:Slidenutthenferruleontocopper

tubingabout1"(2.5cm).

NOTE:Topreventvibrationduringoperation,routethe

watersupplylinesothatitdoesnottouchthe

dishwasherbase,frameormotor.

Coppertubingonly:Putthetubingintothe90°elbow

fittingasfarasitwillgo(thecoppertubingbendsand

kinkseasily).Slidethenutandferruleforwardandstart

thenutontotheelbowthreads.

Flexiblebraidedconnection:Securenuttoelbowusing

5/8"openendedwrenchoradjustablewrench.

NOTE:DonotuseTeflon®tapewithcompressionfittings.

Holdthe90°elbowfittingstillwithoneadjustablewrench

andtightenthenutwithsecondadjustablewrench.

Helpful Tip: Use a 5/8 open ended wrench for easier

access to tighten connection.

Place paper towel under 90 ° elbow fitting. Turn on water

supply and check for leaks. If leak occurs, repeat

previous step.

If needed, see website for animated representation

of this step. Visit www.whirlpool.eom/watersupply

under FAQ tab.

iiiiif_i_if_i_if_i_if_i_ii_i_iii_i_iii_i_i_i_iiii_i_iii_i_iii_i_iii_i_iii_i_iii_i_iii_i_iii_i_iii_i_iii_i_ii_i_ii_iii_i_iii_ii_iiiiiii_ii_iii_ii_iii_i_ii_i_ii_i_iiiii_i_iiiIiiiii:;i;;ii;:;i;;ii_ii;;ii;:;i;;i;;ii;;;i;;ii;ii_ii;;ii;:;i;;ii;:;:;i;;ii_i_iiii11iii_tiiiiiiiiiii_i}iiii_;_ii}iiii_;_ii}iiii_;_ii}iiii_;_ii}iiii_;_ii}iiii_;_ii}iiii_;_ii}iiii_;_ii}iiii_;_ii}iiii_;_ii}iiii_;_ii}iiii_;_ii}iiii_;_ii}iiii_;_ii}iiii_;_ii}iiii_;_ii}iiii_;_ii}iiii_;_ii}iiii_;_ii}iiii_;_ii}iiii_;_ii}ii}iiiiii_;i_iiiiiiiiiiiiiB

Connect to Drain

Black drain hose

Green clam

Sto p

Drain hose

Drain hose stop

Place towel under drain hose to catch any water in drain

hose. Place the small green drain hose clamp onto the

small end of the drain hose. Push the new drain hose

into the black drain hose connector up to the drain hose

stop.

Using pliers, squeeze open the small green drain hose

clamp and slide onto connector between stops.

Once connected, remove towel.

If needed, see website for animated representation of

this step. Visit www.whirlpool.com/drain under FAQ tab.

Make DirectWire Electrical

Connection

NOTE: If the power supply cord was connected earlier

proceed to Secure Dishwasher in Cabinet Opening

section.

Option B, Direct Wire:

Route cable so that it does not touch dishwasher motor

or lower part of dishwasher tub. Pull cable through cable

clamp in terminal box.

Select UL listed or CSA approved twist-on wire connectors

(not included) rated to connect your household wiring to

16-gauge dishwasher wiring.

ElectricalShock Hazard

Electrically ground dishwasher.

Connect ground wire to green ground connector

in terminal box.

Do not use an extension cord.

Failure to follow these instructions can result in

death, fire, or electrical shock.

I !7i\ +

I 1%-C-LI) f-r_.."_ll--Oround i

ILl wire c # L_/_lr7 d TM

=sh

Ground

Form bare ground wire into a U-shaped hook. Wrap

ground wire hook clockwise around ground connector

screw and under the washer. Securely tighten ground

connector.

NOTE: Twist on UL listed or CSA approved wire

connector. Gently tug on wires to be sure both are

secured.

Connect wires black to black and white to white, using

UL listed or CSA approved twist-on wire connectors (not

included).

)

If needed, see website for animated representation

of this step. Visit www.whirlpool.eom/eleetrical under

FAQ tab.

Tighten conduit connector screws to secure cable.

Place wires inside terminal box. Insert tabs on left side

of cover. Make sure wires are tucked inside box. Close

cover ensuring wires are not pinched. Use 1/4" nut

driver and previously removed screw to secure cover.

Checkthatdishwasherisstilllevelfrontto backandside

tosideincabinetopening.

IMPORTANT: If you have solid countertops such as

corrian, granite, etc., you must use side mounting kit

(Part No. 8212560). Follow kit instructions. (Brackets

included with kit.)

Open dishwasher door, remove lower dish rack, and

place towel over pump assembly and lower spray arm of

dishwasher. This will prevent screws from falling into

pump area when securing dishwasher to countertop.

NOTE: Do not drop screws into bottom of dishwasher.

Locate brackets on top of dishwasher and secure

dishwasher to countertop with two, #10 x 1/2" phillips-

head screws (included). The dishwasher must be secured

to keep it from shifting when door is opened.

Check that top of door does not contact screws,

brackets, or countertop. If it does, adjust leveling legs.

Open door and check that space between dishwasher

cabinet opening and tub is equal on both sides. If

spacing is not equal, loosen bracket screws secured

and shift tub. Tighten bracket screws.

Removetowelfromdishwasher.Reinstallthelower

dishrack.

If needed, see website for animated representation

of this step. Visit www.whirlpool.eom/anchoring under

FAQ tab.

Check that grounding clip is attached to the lower panel.

Position the lower panel behind the access panel. On some

models there is insulation on the access panel which must

fall behind the insulation on the lower panel.

Hold the two panels together and place them against

dishwasher leg. Using a philips or 1/4" screwdriver, reinstall

the screws through the holes in the access panel and the

slots in the lower panel.

Check that the lower edge of the lower panel contacts

the floor. Adjust if necessary.

Tighten access panel screws.

TEFLON is a registered trademark of E.I. Du Pont

De Nemours and Company.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result

in death, fire, or electrical shock.

Plug into a grounded 3 prong outlet. Check that power

supply cord does not touch dishwasher motor or lower

part of dishwasher tub.

Reconnect Power

Check Operation

[_ Read the Dishwasher User Instructions that came

with your dishwasher.

[_ Check that all parts have been installed and no steps

were skipped. Check that you have all tools used.

[_ Start dishwasher and allow it to complete the shortest

wash cycle. After the first 2 minutes unlatch door,

wait 5 seconds, then open door. Check to see that

there is water in the bottom of the dishwasher tub.

Check that dishwasher is working properly.

If not, disconnect power or unplug dishwasher and

see "If Dishwasher Does Not Operate" section.

Has the circuit breaker tripped or the house fuse

blown?

Is the door closed tightly and latched?

Has the cycle been set correctly to start the

dishwasher?

Is the water turned on?

If none of these work, call 1-800-253-1301, or in Canada,

call 1-800-807-6777.

For Roper models, call 1-800-447-6737, or in Canada call

1-800-807-6777.

Additional Tips

Expect longer wash times. Your new dishwasher will

average 2-3 hours per load, but use nearly 40% less

energy than older models. Designed with a low wattage,

low energy consumption motor, your dishwasher

washes longer to ensure exceptional cleaning. Certain

models are equipped with an optical water sensor so the

first cycle will run longer to calibrate to optical sensor.

Selecting certain options could increase cycle time past

3.5 hours.

Rinse Aid is necessary for good drying results:

This dishwasher is designed to be used with rinse aid for

good drying performance and controlling hard water

deposit build-up. Energy efficient dishwashers use less

water and energy so they depend on the water sheeting

action of rinse aid for good drying performance.

Start/Resume light may flash:

When pressing Start/Resume, you must make sure the

door is closed within 3 seconds. If you do not, the

Start/Resume light will flash until you press it again.

(You must also do this when adding a dish during the

middle of a cycle.)

La page charge ...

Inglis GU2300XTVS1 Guide d'installation

Marque: Inglis

Modèle: GU2300XTVS1

Catégorie: Lave-vaisselle

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: Inglis GU2300XTVS1 Installation guide

Documents connexes

Inglis ADB1400AWW0 Guide d'installation

Inglis GU2300XTVS1 Guide d'installation

Inglis GU2300XTVS1 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents