GE PDWT400R30WW Guide d'installation

Marque: GE

Modèle: PDWT400R30WW

Catégorie: Lave-vaisselle

Taper: Guide d'installation

04 _,Mf

Appliances

Installation Instructions

Built-In Dishwasher

If you have questions, call 800.GE.CARES(800.432.2737) or visit our Website at: GEAppliances.com

In Canada call 1.800.561.3344 or www.GEAppliances.ca

BEFORE YOU BEGIN

Readthese instructions completely and

carefully.

| L J l"_t'_ _'T'A k |'It

I Ivli_Ui_ | _l_l| - The dishwasherMUST

be installedtoallowforfutureremovalfromtheenclosure

if service is required.

IM PORTANT Observeallgoverning codesand

ordinances.

• Note to Installer - Besure to leave these instructions for the

consumer's and local inspector's use.

• Note to Consumer - Keep these instructions with your

Owner's Manual for future reference.

• Skill Level- Installation of this dishwasher requires

basic mechanical, electrical and plumbing skills. Proper

installation is the responsibility of the installer. Product

failure due to improper installation is not covered under

the GEAppliance Warranty. Seewarranty information.

• Completion Time - 1 to 3 Hours. New installations require

more time than replacement installations.

If you received a damaged dishwasher, you should

immediately contact your dealer or builder.

Optional Accessories - See the Owner's Manual for available

custom panel kits.

FOR YOUR SAFETY

Read and observe all CAUTIONSand WARNINGS

shown throughout these instructions, While performing

installations described in this booklet, gloves and either

safety glasses or goggles should be worn,

READ CAREFULLY.

KEEP THESE INSTRUCTIONS.

Stainless SteelTub Models

imagination at work

Installation Preparation

PARTS SUPPLIED WITH

INSTALLATION KIT:

[] Two #8-18 x 5/8" Phillips special head screws, to

secure dishwasher to underside of countertop or

sides of cabinets.

[] Junction box cover and #!0-1/2" hex-head screw

[] Side and top trim

[] Trim Panel Accessorg Kit (not shown)

(Custom panel models onlg)

[] Sound upgrade kit (some models)

[] Drain hose (78"), drain hose hanger and hose

clamp

[] Literature, product samples and/or coupons

[] Hard water test strip (Models with Bulk Dispenser)

Screw Kit

#8 Phillips

Special Head Screws

5/8" long

#10 Hex-Head

J-Box Screw

1/2" long

_ound Upgrade Kit

{Some Models)

tl Hard Water Test Strip

J(Models with

Bulk Dispenser)

Side Trim

Top Trim

Trim Pieces

Drain Hose Hanger

Drain Hose (78")

Junction

Box Cover

Hose Clamp

MATERIALS YOU WILL NEED:

[] Ferrule, compression nut and 90° Elbow (5/8" NPT

external thread on one end, opposite end sized to

fit water supplg)

[] Thread seal tape

[] UL-listed wire nuts (3)

Materials For New Installations Only:

[] Air gap for drain hose, if required

[] Waste tee for house plumbing, if applicable

[] Electrical cable or power cord, if applicable

[] Screw-tgpe hose clamps

[] Strain relief for electrical connection

[] Hand shut-off valve

[] Water line 5/8" min. copper

[] Coupler for extending drain line, if applicable

[] GPF10L!0' drain hose, if needed

90° Elbow, Hand Thread Wire Nuts (3)

Ferrule and Shut-Off Seal Tape

Compression Nut Valve

Waste Tee

_ Air

Gap

Hot Water Line

Electrical Cable

(or Power Cord, if applicable)

GPF20L

20' Drain Hose

Screw-Tgpe Strain Relief Coupler

Hose Clumps

TOOLS YOU WILL NEED:

[] Phillips-head screwdriver

[] !/4" and 5/16" nutdriver

[] 6" Adjustable wrench

[] Level

[] Carpenter's square

[] Measuring tape

[] Safetg glasses

[] Flashlight

[] Bucket to catch water when flushing the line

[] !5/16" socket

[] Gloves

For New Installations Only:

[] Tubing cutter

[] Drill and appropriate bits

[] Holesaw set

Head

Screwdriver

114"and

15116" Socket

Flashlight

Gloves

5/16" Nutdriver

Level

6" Adjustable Tubing Cutter

Wrench Carpenter's

Safetg Glasses Measuring Tape

Bucket Hole Saw Set Drill and Bits

Installation Preparation-Enclosure

PREPARE DISHWASHER ENCLOSURE

To reducethe riskofshock,fire,orinjurg

topersons,the installermust ensurethat

thedishwasheriscompletelgenclosedat

thetimeofinstallation.

Pare reducir el riesgo de choque, incendio

o lesi6n a personas, el instalador se

debe cerciorar de que la lavadora est_

completamente cerrada en elmomento

de lainstalaci6n.

•The rough cabinet opening must have a minimum width

and depth of 24" and height of ]4-1/2" _+1/4" from the floor

to the underside of the countertop.

• The back wall should be free of pipes or wires.

Adjacent cabinets should be square and plumb to ensure

a good fit. Refer to Figure A

For a corner installation, allow 2" minimum clearance

between the dishwasher and the adjacent wall.

Provide at least 28-5/8" infront of the dishwasher to allow

the dishwasher door to open fully. Referto Figure B

• The dishwasher must be installed no more than 10 feet

from sink for proper drainage.

The dishwasher must be fullg enclosed on the top, sides

and back.

The dishwasher must not support any part of the enclosure.

[

Countertop

Dishwasher

2" Minimum

Clearances:

In a corner installation, provide at

least 2" clearance between the

dishwasher and the adjacent

cabinet, wall, or other appliance.

Provide at least 28-3/8" of clearance

in front of the dishwasher.

28-3/8" Minimum

Figure B

34-1/2" + 1/4"

Underside of

Countertop

to Floor

Figure A

Floor MUST

be Evenwith

Room Floor

J 24" Min:

Squore

ond

Plumb

Plumbing and Electric Service

Must Enter Shaded Area

• Moke sure the floor is level inside the opening and even with

the finished floor of the kitchen. This will facilitate removal

of the dishwasher at a later date for service, if needed.

Special consideration for a dishwasher installed on

a elevated platform

The elevated platform must be flat and level.

InstallationPreparation-Drain

PREPARE DRAIN PLUMBING

Drain Requirements

• Drain hose must not exceed 10 feet in length.

• A high drain loop or air gap is required. See below.

Drain Method

The tgpe of drain installation depends on the following:

• Do local codes or ordinances require an air gap?

• Iswaste tee less than 18" above the floor?

If the answer to either question is yes, an air gap must be used.

Referto Method 1 (Figure C)in the adjacent illustrations.

If both answers are no, either an air gap or high drain loop mag

be used. Refer to Method 1 (Figure C)or Method 2 (Figure D)

in the adjacent illustrations

NOTE: Drain hose elevation must not exceed 48".

Special consideration for a dishwasher installed on

a elevated platform

Ifthe dishwasher isinstalled on an elevated platform, a high

drain loop of at least 32" above the platform must be provided

in addition to the air gap or drain loop requirement determined

above. This is necessmrgfor proper drain performance.

CAUTION

An air gap MUSTBEUSEDif the drain hose is connected to

waste tee or disposer lower than 18" above the floor level.

Failure to provide the proper drain connection height with

an air gap or 32" minimum, high drain loop will result in

improper draining of the dishwasher, which may cause

damage.

PRECAUCION

SEDEBEUSARun espacio de aire si la manguera

de drenaje se conecta a la Tde desechos o al triturador

menos de 18" por encima del nivel del piso. No disponer

la altura correcta de la cone×i6n del drenaje con

un espacio de aire o 32" de minimo, una curva alta

de drenaje resultar_ en un drenaje incorrecto

de la lavadora, Io que pude causar da6os.

METHOD 1-Air Gap with Waste Tee or Disposer

Figure C

Waste TeeInstallation

Disposer Installation

METHOD 2-High Drain Loop with Waste Tee

or Disposer

Usethe drain hose hanger included in the installation kit to

attach the drain hose to the underside of the countertop.

Attachment will be made in a later step.

_ Figure D

Waste Tee Installation

in.

DisposerInstallation

Install waste tee or disposer and the air gap according to the

manufacturer's instructions.

Cabinet Preparation for drain line

Drill a 1-1/2" diameter hole in the cabinet wall within the

shaded area shown in Figure A for the drain hose. Make

sure there are no sharp edges. The drain hose will be passed

through this hole and connected to the drain in a later step.

IMPORTANT-when

connecting the drain line to a

disposer, check to be sure that

drain plug has been removed.

Dishwasher will not drain if

plug is left in place.

_ Remove

Drain

Plug

Installation Preparation-Electrical Supplg

PREPARE ELECTRICAL WIRING

FOR PERSONALSAFETY: Remove house fuse

or open circuit breaker before beginning

installation. Do not use an extension cord or

adapter plug with this appliance.

PARASEGURIDAD PERSONAL: Retire el

fusible de la casa o abra el interruptor de

circuitos antes de empezar la instalaci6n.

No use un cable de extensi6n o enchufe

adaptador con este aparato.

Electrical Requirements

• This appliance must be supplied with 120V,60Hz., and

connected to an individual properlg grounded branch circuit

protected bg a 15- or 20-ampere circuit breaker or time-

delag fuse.

• Wiring must be 2 wire with ground and rated for 75°C(176°F).

• If the electrical supplg does not meet the above

requirements, call a licensed electrician before proceeding.

Grounding Instructions-Permanent Connection

This appliance must be connected to a grounded-metal,

permanent wiring sgstem, or an equipment-grounding

conductor must be run with the circuit conductors and be

connected to the equipment-grounding terminal or lead on

the appliance.

Grounding Instructions-Power Cord Hodels

This appliance must be grounded. Inthe event of a malfunction

or breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current.

This appliance is equipped with a cord having an equipment-

grounding conductor and a grounding plug. The plug must

be plugged into an appropriate outlet that is installed and

grounded in accordance with all local codes and ordinances.

_The improper connection of the equipment

grounding conductor can result in a risk

of electric shock. Check with a qualified

electrician or service representative if gou

are in doubt that the appliance is properlg

grounded.

/ I

I I

Alternate q',

I \

Receptacle , \

Location

1-1/2" Dia.

Hole (Max.)

Location

Area

3" from

Cabinet

Figure E White

For models equipped with power cord: Do not modifg the plug

provided with the appliance; if it will not fit the outlet, have a

proper outlet installed by a qualified technician.

Cabinet Preparation and Wire Routing

• The wiring mag enter the opening from either side, rear

or the floor within the shaded area dimensioned in Figure A

and illustrated above.

Cut a !-!/2" max. diameter hole to admit the electrical cable.

Cable direct connections mag pass through the same hole

as the drain hose and hot water line, if convenient. If cabinet

wall ismetal, the hole edge must be covered with a bushing.

Note: Power cords with plug must pass through a separate

hole.

Electrical Connection to Dishwasher

Electrical connection is on the right front of dishwasher.

Forcable direct connections the cable must be routed as

shown in Figure E.Cable must extend a minimum of 24"

from the rear wall.

Forpower cord connections, install a ]-prong grounding

tgpe receptacle inthe adjacent cabinet rear wall, 6" min.

or 18" max. from the opening, 6" to 18" above the floor.

The receptacle must be accessible and therefore cannot

be installed in the back wall of the dishwasher enclosure.

La conexi6n incorrecta del conductor de

conexi6n a tierra del equipo puede resultar

en choque el6ctrico. Consulte con un

electricista calificado o representante

de servicio si tiene dudas de la conexi6n

a tierra del aparato.

Installation Preparation-Hot Water Supply

PREPARE HOT WATER SUPPLY

Hot Water Line

• The line meg enter from either side, rear or floor within the

shaded area shown in Figure F.

• The line meg pass through the same hole as the electrical

cable and drain hose, or an additional 1-!/2" diameter hole

meg be cut to accommodate the water line. If a power cord

with plug is used, the water line must not pass through the

power cord hole.

/ I

_1-1/2" Oi,

Hole

ii Shut-off7

Valve Y

Hot_ i:::::::::: ,%.:',::',:':

:: L.

_2"

From

Cabinet

CabinetFace_,-

I__.!9" From Wall

2" From Floor

I \

Figure F

CAUTION

The hot water supplg line pressure must be at least 20 PSI.

Lower pressures could cause the water valve to leak and

cause water damage.

PRECAUCI6N

La linea de presi6n del suministro de ague caliente debe

ser al menos 20 PSI.Presiones inferiores podrian causer

que la v61vula del ague gotee g causer da_os por ague.

Water Line Connection

• Turn offthe water supplg.

• Install a hand shut-off valve in an accessible location, such

as under the sink. (Optional, but stronglg recommended

and meg be required bg local codes.)

• The water connection is on the bottom-left side of the

dishwasher. Install the hot water inlet line, using 3/8"

or larger copper tubing. Route the line as shown in Figure F

and extend forward at least 19"from rear wall.

• Adjust the water heater to deliver water between 120°F

and !50°F.

• Flush water line to clean out debris. Use a bucket to catch

water and debris.

• The hot water supplg line pressure must be between 20

and 120 PSI.

Dishwasher Installation

CAUTION

Do not remove the wood base until you are ready to

install the dishwasher. The dishwasher will tip over

when the door isopened if the base is removed.

PRECAUCION

No retire la base de madera hasta que est_ listo para

instalar la lavadora de platos. Cuando la puerta se abra,

la lavadora de platos se inclinar6 si la base se retira.

STEP 1 - LOCATE INSTALLATION ITEMS

• Locate the items in the installation package and set aside for

use in the listed steps.

• Trim pieces - Step 2

Junction box cover - Step 7 or Step 18

Drain hose and clamp - Step 10

Screw Kit - Step 15

Drain hose hanger - Step 17

Owner's Manual - Step 19 and Step 24

Hard Water test strip - Step 21

Sound upgrade kit (selected models) - Step 22

Product samples and/or coupons - Step 24

Tgpe 1 - One-hole cable

Adjust tension bg moving spring hook to one of the three holes

on the tub leg.

!INCREASE

DECREASE

One Hole

Figure H

Tgpe 2 - Three-hole cable

Adjust tension bg moving spring hook to one of the three holes

on the pulley cable.

STEP 2 - INSTALL TRIM PIECES

Inthis step, gou will need the trim pieces set aside in Step 1.

Presstop trim piece onto top of tub flange. Start with the

right edge and work gour wag to the left.

Repeat process with the left and right trim pieces working

from the top down.

Open and close the door to check that trim does not bind

and does not interfere with door latch or door hinges.

TrimStrip

Trim -

Strip

Figure G

STEP 3 - CHECK DOOR BALANCE

• With dishwasher on the wood skid,check the door balance

bg opening and closing the door.

If the door drops when released, increase the spring tension.

If the door rises when released, decrease the tension.

There are two tgpes of counterbalance and therefore two

methods of adjustment. Identifg which counterbalance is

present and adjust tension accordinglg. Pleasenote: If there

are 3 holes on the cable, use the cable to adjust; if there is

one hole on cable, use the tub leg to adjust.

Decrease

Figure I

Increase

Tension

After adjusting spring tension, open and close the door to

make sure the door operates smoothlg. If the door is hard

to move or if the spring cable binds, check the routing of

the spring cable. The cable should be routed between the

shoulders of the pulleg cable roller. If the cable isoff the roller:

latch door, remove spring tension and route the cable between

the shoulders of the roller.See FigureJ.

Pulle__

Shoulder

Correct Spring

Figure J

Cable Routing

IncorrectSpring

CableRouting 7

Dishwasher Installation

STEP 4 - REMOVE WOOD BASE,

INSTALL LEVELING LEGS

IMPORTANT- Donotkickoffwoodbase!Damage

will occur.

. Move the dishwasher close to the installation location and lag

it on its back.

• Remove the four leveling legs on the underside of the wood

base with an adjustable wrench or 15/!6" socket.

• Discard base.

)rox.

Figure K

. Screw leveling legs back into the dishwasher frame

approximatelg !/8" from frame as shown.

STEP 5 - REMOVE TOEKICK

• Removethe 2 toekick screws

and toekick.

Set aside

for use in

Step 23.

_,emove 2

Figure L Toekick Screws

STEP 6 - REMOVE TOEKICK BRACE

Skip this step if your model does not have a sound upgrade

kit. If your model does have a sound upgrade kit, this brace

must be removed.

• Remove the 2 toekick brace

screws and

toekick brace.

Discard brace

and set

screws aside

for use in

Step 22.

Figure M

;emove 2

Toekick Screws

STEP 7 - INSTALL POWER CORD

Skip this step if dishwasher will be permanentlg connected

to the house electrical sgstem.

In this step gou will need the junction box cover and the

#!0 x !/2" hex-head screw from the screw kit set aside in

Step i.

The power cord and connections must complg with the

National Electrical Code, Section/422 and/or local codes and

ordinances. Maximum power cord length is6 feet. Power Cord

Kit wxogx70910, available for purchase from an authorized

GEAppliance Dealer, meets these requirements.

Figure N

Ground

• Install strain relief injunction box bracket.

• Insert power cord through strain relief and tighten.

Make sure black, white and green dishwasher wires are

threaded through small hole injunction box bracket.

Connect like-colored dishwasher and power cord wires. If

power cord wires are not color-coded, connect the ribbed

power cord wire to the white dishwasher wire, the smooth

power cord wire to the black dishwasher wire and the ground

to the green dishwasher wire. Use UL-listed wire nuts of

appropriate size.

Install junction box cover set aside in Step 1, using #!0 hex-

head screw. Besure wires are not pinched under the cover.

Dishwasher Installation

STEP 8 - INSTALL 90 ° ELBOW

• Wrap 90° elbow with thread seal tape.

• Install a 90° elbow onto the water valve.

Front of Dishwasher

90°

Elbow

Figure 0

Water Valve

Bracket

I Hose

Thread

Seal Tape

• Do not overtighten the 90° elbow; water valve bracket could

bend or water valve fitting could break.

Position the end of the elbow to face the rear of the

dishwasher.

STEP 9 - POSITION WATER LINE AND

HOUSE WIRING

• Position water supply

line and house wiring

on the floor of the

enclosure to avoid

interference with

base of dishwasher

and components

under dishwasher.

Figure P

STEP I0 - INSTALL DRAIN HOSE TO

DISHWASHER DRAIN PORT

In this step you will need the drain hose and clamp set aside

in Step 1.

Stand dishwasher upright.

• Place drain hose clamp over 1-5/16" inside diameter end

of drain hose with the clamp screw positioned on the bottom

of the hose.

IMPORTANT- Prevent drain hose damage and

possible leaks. Be careful not to nick or cut the drain hose.

Push the end of the drain hose over the drain pump outlet

being careful not to disturb the check valve. Refer to Figure q).

Seat the drain hose end against the hose stops on the pump

outlet.

Position hose clamp against the front lip of the drain hose

and tighten clamp.

NOTE:Drain hose

supplied with dish-

washer isapproxi-

mately 78" long.

Ifa longer hose is

needed, a 120" long

hose (!0 feet) may

be purchased from

an authorized

GEappliance

dealer.The

!0' long

hose is

port

number

GPFIOL.

Figure Q

PumpOutlet HoseStop

Tip: Avoid unnecessarg service charges. Make a leak free

connection

Insert hose against stop on pump. Position clamp against front

lip of drain hose with clamp screw on bottom side of hose.

Tighten clamp to at least !5 inch-pounds of torque.

Tip: Reduce drain pump noise

Position drain hose clamp so screw is on the bottom side of the

hose. This will prevent noise caused by the clamp coming in

contact with the tub bottom. Refer to Figure q).

Dishwasher Installation

STEP 11 - INSERT DRAIN HOSE

THROUGH CABINET

• Position dishwasher in front of cabinet opening. Insert drain

hose into the hole in cabinet side. If a power cord is used,

guide the end through a separate hole.

Drain

Hose Length 10'

Blanket

Hose

House Wiring

(If Power Cord

is NOT Used)

Power Cord

(If Used)

Figure R

Tip: Position water line and house wiring on the floor to avoid

interference with base of dishwasher.

STEP 12 - SLIDE DISHWASHER THREE-

FOURTHS OF THE WAY INTO

CABINET

IM _UK i_l_l|- DO NOT PUSH AGAINST FRONT PANEL

WITH KNEES.DAMAGE WILL OCCUR.

',Grasp the dishwasher bg its sides and slide it into the opening

a few inches at a time.

o Not Push Against

Front Door Panel With

Knee. Damage to The

Door Panel Will Occur.

Figure S

• As gou proceed, pull the drain hose through the opening

under the sink. Stop pushing when the front of the

dishwasher isa few inches forward of adjacent cabinets.

• Make sure drain hose isnot kinked under the dishwasher

and there is no interference with the water line,wiring or ang

other component.

Tip: Make sure the dishwasher will fit in the cabinet. Check to

be sure the power cable, drain hose and hot water line are not

trapped behind the dishwasher. Utilitg lines trapped behind the

dishwasher prevent the dishwasher from being pushed fullg

into the enclosure.

Dishwasher Installation

STEP 13 -SLIDE DISHWASHER INTO

FINAL POSITION

• Pushthe dishwasher the rest of the wag into the cabinet.

• Pushthe sides with your hands. Do not push the dishwasher

with your knee, as this will damage the door.

Check that the tub insulation blanket does not get

"bunched up" or interfere with the springs as you slide it

into the cabinet.

Center the dishwasher in the opening.

Front of door panel should be flush with face of cabinet.

Carefully open and close the door to ensure that the door

panel does not catch or rub on the cabinet frame. Refer

to Figure U below.

If the door catches or rubs on the frame, reposition and/or

levelthe unit (seeStep 14)until the door moves freely and

does not contact the cabinet frame.

Special Considerations for Positioning

Top-Mount Control Models

The controls onthese models are designed to be hidden by

your countertop. Align the dishwasher as shown in Figure

V.Leave a 1/2" minimum gap between the underside of the

countertop and the top of the dishwasher door as shown in

Figure W.

Use the leveling legsto increase or decrease the amount

of gap between the controls and the countertop.

Forflush installations of the custom panel models, it may

be necessary to cut off the back panel of the tub insulation

blanket so that the dishwasher door panel can be aligned with

the kitchen cabinet panels.

Door

Fits and

Swings

Back

Behind

Frame

Alignment

Door Catches on

Cabinet Frame

IN PORTANT- Leave a i/2" minimum gap between

the controls and the underside of the countertop to prevent

condensation and damage to the control panel from screw

heads.

Controls Hidden_---_____

by Countertop

Figure V

Figure U

Incorrect

Alignment

1/2"

Him.

Countertop

Dishwasher Door

Figure W

Dishwasher Installation

STEP 14 - LEVEL DISHWASHER

IMPORTANT- Dishwasher must be level for proper

dish rack operation and wash performance.

• ForTop-Mount Control Models:

Make sure 1/2" minimum gap is maintained.

• For All Models:

Placelevelon door to check that the dishwasher is level

sideto side. Removelower

rock,placelevelon lower

rack track insidetub to / \

check that the q ,;

d,s wos er,s,e ,

use I_-#, _ttlf use

Level to--_t_/ \\\IfliLevel to

Check t_ " " _f 'Check

Front _/1_\_, Side

Figure X

• If adjustment to the

right-rear leveling leg

isrequired, access it

bg loosening the

junction box bracket

screw (through the

access hole) and

rotate bracket clockwise.

• If the dishwasher is not level, adjust the four leveling legs

msillustrated in Figure Y.

L gunctionBox Acc s Ho,e/

to Adjust //

Figure Y

•The dishwasher is properlg leveled when the level indicator is

centered left to right and front to back. The dishwasher door

should close without hitting the sides of the tub,

• Replace the lower rack when leveling iscomplete.

Tip: Avoid unnecessarg service charges forpoor wash

performance and rack operation.

Pullthe dish racks half wag out. Theg should remain stationary.

Open and close the door.The door should fit in the tub opening

without hitting the side of the tub. If the racks roll on their own,

or the door hits the side of the tub, relevel the dishwasher.

IMPORTANT - After leveling, verifg that the

dishwasher is centered in the enclosure and the door does

not hit adjacent cabinets.

STEP 15 - SECURE DISHWASHER TO

COUNTERTOP OR CABINET

In this step gou will need

the 2 Phillips special head

screws set aside in Step 1.

The dishwasher must be

secured to the countertop

or the cabinet sides. When

countertops are made of Tub

wood, use Method 1.When

countertops are granite or

other materials that will not

accept screws, use Method FigureZ

2 to secure dishwasher at the sides.

Brackets

Countertop

Mounting

Brackets

IMPORTANT-

Avoidunnecessarg

servicecharges.

Drive screws straight

and flush. Protruding

screw heads will

scratch the top or

sides of the control

Wood Cooktop

Screws

FigureAA

panel and can interfere with door closing.

Method 1

Securedishwashertowood countertop

• Fasten the dishwasher to the underside of the countertop

with the 2 Phillips special head screws provided.

Method 2

Secure dishwasher with side-mounting brackets

• Remove plug buttons (one on each side).

• Install screws through the dishwasher side-mount bracket

and into the adjacent cabinet on each side. Reinstall plug

buttons.

Granite C0unterto p

_1_ r l_i_

_Plug .....................

Figure BB

EitherMethod-ForTop-Mount ControlModels.

Make certain1/2"gap minimum ismaintained.

• When step is complete, close dishwasher door and verifg

that gap between countertop and top of dishwasher door is

at least 1/2".

Countertop

1/2'<¢__

Hin.| Dishwasher Door

Figure CC

Dishwasher Installation

STEP 16 - CONNECT WATER SUPPLY

Connect water supply line to the 90° elbow.

• Slide compression nut, then ferrule over end of water line.

• Insert water line into 90° elbow.

Slideferrule against elbow and secure with compression nut.

IMPORTANT- Check to be sure that door spring does

not rub or contact the fill hose or water supply line. Test by

opening and closing the door. Reroute the lines if a rubbing

noise or interference occurs.

Figure DD _o

Compression Nut

Ferrule

Hot Water x

E!h°w Supply Line

--.Door Spgr_ngElb°w

STEP 17 - CONNECT DRAIN LINE

The molded end of the drain hose will fit 5/8" through 1"

diameter inlet ports on the air gap, waste tee or disposer.

• Determine size of inlet port

• Cut drain hose connector on the marked line, if required, to fit

the inlet port.

Cutting Line IMPORTANT: Do not cut corrugated

_¢" portion of hose

Figure EE

• If a longer drain hose is required, and you did not purchase

!0' long GPFIOLdrain hose, add up to 3-1/2' of length for a

total of !0' to the factory-installed hose. Use 5/8" or

7/8" inside diameter

hose and a coupler

to connect the

two hose ends.

Secure the

connection with

hose clamps.

Figure FF

Hose Clamp

Coupler

Hose Clamp

NOTE:TOTAL DRAIN HOSE LENGTH MUST NOT EXCEED 10' FOR

PROPER DRAIN OPERATION.

DRAIN LINE INSTALLATION

• Connect drain line to air gap, waste tee or disposer using

the previously determined method.

• Secure the drain hose to the air gap, waste tee or disposer

with clamps.

Method 1 - Air gap with waste tee or disposer

Insert the drain hose into the air gap as shown.

Waste Tee Installation

Figure GG

Disposer Installation

Method 2 - High Drain Loop with the Waste Tee or Disposer

Route the drain hose of the dishwasher to a minimum height of 32" from

the floor with the supplied hanger as shown.

Waste Tee Installation

Figure HH

! |

Disposer Installation

IMPORTANT- One of the above methods must be

used or dishwasher will not operate properly.

IMPORTANT- Whenconnecting

drain line to disposer, check to be sure

that drain plug has been removed.

DISHWASHERWILL NOT DRAIN IF

PLUGISLEFTIN PLACE.

[_ _-- Remove

Hopper

Plug

Tip: Avoid unnecessary service call charges. Always be sure

disposer drain plug has been removed before attaching

dishwasher drain hose to the disposer.

Dishwasher Installation

STEP 18 - CONNECT POWER SUPPLY

Skip this step if dishwasher is equipped with power cord,

Verify that power is turned off at the source.

• Locate junction box cover set aside in Step 1.

• Secure house wiring to the back of the junction box with a

strain relief.

• Locate the three dishwasher wires, (white, black and green)

with stripped ends. Insert dishwasher wires through the small

hole in thejunction box. Connect like-colored dishwasher and

power cable wires using UL-listed wire nuts of appropiate size.

• Install the junction box cover. Check to be sure that wires are

not pinched under the cover.

Figure II Grounnd

White

,__,.Black

If house wiring is not 2-wire with a ground

wire, a ground must be provided by the

installer.

When house wiringisaluminum, be sure

to use U.L.-listed anti-oxidant compound

and aluminum-to-copper connectors.

" - Siel cableado de la casa no es de 2 cables

•I, Iconun cable de conexi6n a tierra, el

_,/ instalador debe suministrar una conexi6n

_,_'_,_ a berra.

_lr Cuando el cableado de la casa es en

aluminio, cerci6rese de usar un compuesto

anti-oxidante aprobado por U.L g un

compuesto de aluminio a cobre.

STEP 19 - PRETEST CHECKLIST

Review this list after installing gour dishwasher to

avoid charges for a service call that is not covered bg gour

warrantg.

[]

Checkto be sure power is OFF.

Open door and remove all foam and paper packaging.

Locate the Owner's Manual set aside in step 1.

Readthe Owner's Manual for operating instructions.

Check door opening and closing. If door does not open and

close freelg, check for proper routing of spring cable over

pulleg. If door drops or closes when released, adjust spring

tension. See Step 3, Figure J.

Checkto be sure that wiring is secure under the dishwasher,

not pinched or in contact with door springs or other

components. SeeStep 9.

Check door alignment with tub. If door hits tub, level

dishwasher. SeeStep 14.

Pull lower rack out, about halfwag. Check to be sure it does

not roll back or forward on the door. If the rack moves,

adjust leveling legs. See Step 14.

Check door alignment with cabinet. If door hits cabinet,

reposition or relevel dishwasher. SeeSteps 13, 14 and 15.

Checkthat door spring does not contact water line, fill hose

or other components. See Step 16.

Verifg water supplg and drain lines are not kinked or in

contact with other components. Contact with motor or

dishwasher frame could cause noise. See Steps 9 and 11.

Turn on the sink hot water faucet and verifg water

temperature. Incoming water temperature must

be between 120°F and 150°F.A minimum of 120°F

temperature isrequired for best wash performance. See

"Prepare Hot Water Supplg," page 6.

Add 2 quarts of water to the bottom of the dishwasher to

lubricate the pump seal.

Turn on water supplg. Check for leaks.Tighten connections

if needed.

[] Remove protective film if present from the control panel

and door.

[] Avoid service call charges bg ensuring there is an air gap

or drain hose routed through the required 32" minimum

height.

Dishwasher Installation

STEP 20 - DISHWASHER WET TEST

[] Turn on power supply (or plug power cord into outlet,

if equipped).

[] Start the unit to check for leaks.

Front-Mount Control Models:

- Close & latch door

- Push RINSEONLYpad

- Push START/RESETpad one time

Top-Mount Control Models:

- Push RINSEONLYpad

- Push START/RESETpad one time

- Close & latch door

[] Check to be sure that water enters the dishwasher. If water

does not enter the dishwasher, check to be sure that water

and power are turned on.

[] Check for leaks under the dishwasher. If a leak is found, turn

off power supply, then tighten connections. Restore power

after leak iscorrected.

[] Check for leaks around the door. A leak around the door

could be caused by door rubbing or hitting against

adjacent cabinet. Reposition the dishwasher if necessary.

See Steps 13, 14 and 15.

[] The dishwasher will drain and turn off about 5 minutes after

it was started. Check drain lines. If leaks are found, turn off

power supply and correct plumbing as necessary. Restore

power after corrections are made. See Step 10

and 17.

[] Open dishwasher door and make sure most of the water

has drained. If not, check to be sure disposer plug has been

removed and/or air gap is clear. SeeStep 17.Also check

drain line to be sure it isnot kinked.

[] Runthe dishwasher through another "Rinse Only" cycle.

Check for leaks and correct if required.

STEP 21 - Set Water Hardness

Models with bulk dispenser onlg. Skip this step if gout

dishwasher does not have the bulk dispense feature.

• Locate the hard water test strip set aside in Step 1.

• Remove strip from package.

• Turn on the hot water and hold the strip under the stream,

following the directions on the package.

• Usethe value on the test strip to calibrate your dishwasher

for water hardness. Refer to the section titled "Water

Hardness Calibration" in your Owner's Manual for information

on how to calibrate your dishwasher.

STEP 22 - INSTALL SOUND UPGRADE KIT

IF EQUIPPED

Skip this step if gour model does not have the

Sound Upgrade Kit.

• Locate sound upgrade kit set aside in Step i and the two

screws set aside in Step 6.

• Attach the plastic Sound Panel as shown in Figure LL using

the two screws. The lower set of mounting holes should be

used.

• Besure the sound panel is seated in the notches on frame

as shown in Figure JJ.

Figure JJ

Attachment

,, _Screws

_esurethat the sound panel

is seated in the notch in

the frame. (Both sides)

Dishwasher Installation

STEP 23 - INSTALL TOEKICK

• Locate toekick and screws set aside in step 5.

Screws

Figure KK

,, Replace the toekick and make sure it is against the floor.

• Insert and tighten the 2 toekick attachment screws. The

toekick should stag in contact with the floor to ensure quiet

dishwasher operation.

STEP 24 - LITERATURE

,, Be sure to leave complete literature package, Installation

Instructions and product samples with the consumer.

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE

GEConsumer & Industrial

General Electric Company

Louisville, Kentucky/40225

GEAppliances.com

206C!559P!99 31-30260 07-09 JR

Instructions d'i

kave-vaisselle encastr

Sivouz des questions, appelez 800.GE.CARES ou visitez notre site Web" GEAppliances.com

Au Canada, appelez le 1.800.561.3344 ou visitez •www.electromenagersge.ca

nstallation

AVANT DE COMMENCER

IIfaut lire soigneusement toutes ces instructions.

IMPORTANT- Lelave-vaisselle DOlT @treinstall_ de

mani@re@permettre la d@ose ult@rieurede I'enceinte afin de

permettre toute intervention.

Iii PORTANT-IIfaut respecter tous lescodes et

r@glements.

* Remerque pour I'instelleteur - IIfaut prendre soin de

laisser ces instructions pour le client et I'inspecteur local.

* Remerque pour le consommeteur - IIfaut garder ces

instructions avec le manuel d'utilisation, pour consultation

ult@ieure.

* Niveeu de competence - L'installation de ce lave-vaisselle

demande des connaissances m@caniques,@lectriques

et de plomberie de base. L'instelleteur est responseble

de I'installation appropri_e. La garantie des appareils

m_nagers de GEne couvre pes les d_faillances du produit

ceus_es per une meuveise installation. Consulter les

renseignements dens le gerentie.

, Dur_e d'instelletion - 1 8 3 heures. Lesinstallations

initiales demandent plus de temps que lesinstallations de

remplacement.

Si le lave-vaisselle livr@est endommag_, il faut contacter

imm@diatement le concessionnaire ou I'entrepreneur de

construction.

Accessoires optionnels - Consulter la liste de n_cessaires de

panneaux de finition dans le manuel d'utilisation.

SECURITE

II feut fire et observer tousles evertissements (PRUDENCE

et ATTENTION)montr_s dens ces instructions. Pendent

Finstellation d_crite dons ce livret, il faut porter des gents et

des lunettes de s_curit&

LIRE ATTENTIVEMENT.

IL FAUT GARDER CES INSTRUCTIONS.

Mod@les_ cuve en acier inoxgdable

imagination at work

Preparation pour I'installation

PII_CES FOURNIES AVEC LE KIT

D'INSTALLATION :

[] Deux vis sp_ciales _ t_te cruciforme n° 8-18 x 5/8 po,

pour fixer le lave-vaisselle au-dessous du plan de travail.

[] Un couvercle de boTtedejonction et une vis d t@te

hexagonale n° 10-1/2 po

[] Finition lat@raleet sup@rieure

[] Kit d'accessoires de finition de panneau (non illustr@)

(Uniquement pour les mod@les@panneaux sur mesure)

[] Kit de r@ductionde bruit (certains mod@les)

[] Tugau de vidange de 198 cm (78 po), porte-tugau de

vidange et collier de tugau

[] Documentation, @chantillonset/ou coupons de

r@duction

[] Bande d'essai d'eau dure (mod@lesd distributeur en vrac)

Ensemble de vis

Vis sp_ciales 6 t_te Vis pour boTte

cruciforme n° 8 de 5/8 J 6 t_te 6 six

po de long pans n° 10 -

1/2 pode long

Finition lat_role

Finition lat_rale

Finition sup(_rieure

Pi_ces de finition

Porte-tugau de

it de r_duction vidange

dnebruit {certains

modules}

[_] Bande d'essai d'eau dare

{modUles 6 distributeur Tugau de vidonge

en vrac) {198cm){78po)

Couvercle de

bastedejonction

Collier de tugau

MATI_RIAUX NI_CESSAIRES :

[] Bague, _crou de compression et coude _ angle droit

(filetage externe de 3/8 po _ une extremitY, I'autre

extr_mit_ correspondant d I'alimentation d'eau)

[] Ruban d'@anch_it_ de filetage

[] Serre-fils sur la liste UL(3)

Mat(_riau× uniquement requis en cas

d'installation initiale :

[] Dispositif anti-siphon pour le tugau de vidange, si

n_cessaire

[] Raccord en t_ pour la plomberie d'_gout, si n_cessaire

[] COble_lectrique ou cordon d'alimentation

[] Colliers de tugau _ vis

[] Dispositif de r_duction de tension pour les branchements

_lectriques

[] Robinet

[] Conduite d'eau en cuivre de 3/8 po minimum

[] Manchon de raccord pour rallonger le tuyau de vidange,

le cas @ch@ant

[] Tugau de vidange GPFIOL (Iongueur de 3 m [10 pi]) si

n@cessaire

OUTILS NI_CESSAIRES :

[] Tournevis cruciforme

[] Tournevis d douille de !/4 poet 5/16 po

[] CI__ molette de 15 cm (6 po)

[] Niveau

[] I_querrede menuisier

[] M_tre ruban

[] Lunettes de s_curit_

[] Lampe de poche

[] Seau pour attraper I'eau Iors de la purge du tugau

[] Douille de 15/16 po

[] Gants

Pour les installations initioles

seulement :

[] Coupe-tube

[] Perceuse et m_ches appropri_es

[] Scie-cloche

Coude 6 angle droit,

bague et _crou de

compression

Robinet d'_tanch_it(_ Serre-fils {3)

de filetage

Raccord en

t(_d'(_gout

_Dispositif

anti-siphon

Tugau d'eau chaude

COble _lectrique

{ou cordon d'alimentation,

si n(_cessoire)

Collier de tugau

6 vis

Tugau de vidange

GPFIOLde3 m{10

pi)en option

Dispositif de

r_duction de

tension

Manchon

cruciforme

Douille de

15116po

Lampe de poche

Gants

douille de 5/16 po

et 1/4 po

Cl_6 molette

de 15cm {6po)

Lunettes de s_curit_

Niveau j

Coupe-tube

Equerre de

sier

M_tre ruban

Seau Scie-cloche Perceuse et m_ches

2 appropri_es

Preparation pour I'installation - Enceinte

PR#PARATION DE L'ENCEINTE DU

LAVE-VAISSELLE

Pour r_duire le risque de choc

_lectdque, d'incendie ou de blessures,

l'instellateur doit s'essurer, au moment

de l'instellation, que le leve-veisselle est

compl_tement enclos.

• L'ouverture de I'armoire non d_grossie doit avoir une largeur

et une profondeur d'au moins 61 cm (24 po) et une hauteur

de 87 cm (34-1/4 po)_+6 mm (1/4 po) du sol 6 la surface du

dessous du plan de travail.

• II ne peut g avoir ni tugaux, ni ills _lectriques sur la paroi

arri_re.

Lesarmoires adjacentes doivent _tre 6 I'_querre et d'aplomb

pour assurer un encastrement parfait. Voir la figure A.

En cas d'installation duns un coin, pr_voir un d_gagement

d'au moins 5 cm (2 po) entre le lave-vaisselle et lemur

adjacent.

Pr_voir un d_gagement d'au moins 72 cm (28-3/8 po)devant

le lave-vaisselle pour permettre I'ouverture complete de la

porte. Voir la figure B.

• IIfaut installer le lave-vaisselle 6 moins de 3 m (10 pi) de

I'_vier pour que I'_coulement suit ad_quat.

Lelave-vaisselle doit _tre enti_rement enclos sur le haut, les

c6t_s et I'arri_re.

Lelave-vaisselle ne peut toucher aucune partie de I'enceinte.

Plandetravail

Lave-vaisselle

i minimumde

(2po)

D_gegements :

Encas d'instullation duns un coin, pr_voir

un d_gagement d'au moins 5 cm (2 po)

entre le lave-vaisselle et lemur adjacent

ou un autre appareil _lectrom_nager.

Pr_voir un d_gagement d'au moins 72 cm

(28-3/8 po) devant le lave-vaisselle.

minimumde72cm

(28-3/8po)

Figure B

au m_me niveau

que le sol de la piece

Figure A

_inlmum

_ 6_,r6r_u°'ree

__ N_ pl°mb

La plomberie et les fils

61ectriques doivent entrer dans

la zone hachur6e

• V6rifier que le sol 6I'int6rieur de I'ouverture d'armoire est

plane et 6 niveau avec le rev6tement de sol de la cuisine. Ceci

facilite I'enl_vement du lave-vaisselle en cas de r6paration

ult6rieure, si n6cessaire.

Conditions sp_ciales s'appliquant _ un lave-vaisselle mont_

sur une plate-forme

La plate-forme doit _tre plane et 6 niveau.

Preparation pour l'installation - Vidange

PRI_PARATION DE LA PLOMBERIE DE

VIDANGE

Exigences de vidange

• Letugau devidange ne peut pas _tre plus de 3 m (10 pi)

de long.

• Une boucle de vidange #lev#e ou un dispositif anti-siphon

est requis. Voir ci-dessous.

M_thode de vidange

Letype d'installation de vidange est li_ aux conditions suivantes :

• Est-ce que les codes ou r_glements Iocaux exigent un

dispositif anti-siphon ?

• Est-ce que le raccord en t# d'#gout se trouve 6 moins de 46

cm (18 po) du sol ?

Si la r#ponse 6 une de ces questions est OUI,il faut utiliser un

dispositif anti-siphon. Se reporter 6 la m_thode 1 (figure ¢) des

illustrations adjacentes.

Si la r#ponse est non aux deux questions, il faut utiliser soit un

dispositif anti-siphon, soit une boucle de vidange #lev#e. Se

reporter 6 la m_thode 1 (figure ¢) ou la m_thode 2 (figure D)

des illustrations adjacentes.

REMARQUE: LQhauteur d'#l#vation du tugau de vidange

ne peut d#passer 122 cm (48 po).

Conditions sp_dales s'appliquant (_un lave-vaisselle mont_

sur plate-forme

Encas d'installation du lave-vaisselle sur une plate-forme, il

faut pr#voir une boucle de vidange #lev#e d'au moins 81 cm

(32 po)au-dessus de la plate-forme en plus du dispositif anti-

siphon ou de la boucle de vidange pr#vu pr#c#demment. ¢ette

mesure assure un #coulement ad#quat de I'eau.

PRUDENCE:

II FAUTutiliser un dispositif anti-siphon si le raccord du

tugau de vidange au raccord en t_ d'_gout ou au brogeur

(_d_chets est (_moins de 46 cm 118po) du niveau du sol. Le

lave-vaisselle risque de ne pas se vidanger correctement

et de s'endommager si le raccord de vidange n'est pas 6

la bonne hauteur avec un dispositif anti-siphon ou une

boucle de vidange _lev_e d'au moins 81 cm 132po).

MI_THODE i - Dispositif anti-siphon avec raccord

en t_ d'@gout ou de brogeur _ d_chets

Figure C

Installationavec un raccord

en t# d'#gout

__ fa

Installation avec un

brogeur 6 d_chets

MI_THODE 2 - Boucle de vidange _lev_e avec un

raccord en t_ d'_gout ou brogeur 6 d_chets

Utiliser le porte-tugau de vidange compris dans le kit de

montage pour suspendre le tugau de vidange sous le plan de

travail. ¢eci sera accompli 6 une _tape ult_rieure.

minimum

Installationavecun raccord

ent_ d'_gout

Installationavecun

brogeur_ d_chets

Installer le raccord en t_ d'_gout ou le brogeur et le dispositif

anti-siphon selon les directives du fabricant.

Preparation de I'armoire pour I'installation du

tugau de vidange

Percer un trou de 38 mm (1-1/2 po)dans la paroi de I'armoire

dans la zone hachur_e indiqu_e (_la figure A pour le passage

du tugau de vidange. V_rifier que les bords du trou sont lisses.

Dans une _tape ult_rieure, il faut glisser le tugau devidange au

travers du trou pour le raccorder au drain.

IMPORTANT- Pendantle

branchement du tugau de vidange _[_

au brogeur 6 d_chets, v_rifier que

le bouchon de vidange a _t_ enlev&

Le lave-vaisselle ne peat passe vider

si le bouchon est en place.

_1 Enlever

le bouchon

de vidange

La page charge ...

GE PDWT400R30WW Guide d'installation

Marque: GE

Modèle: PDWT400R30WW

Catégorie: Lave-vaisselle

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: GE PDWT400R30WW Installation guide

GE PDWT400R30WW Guide d'installation

GE PDWT400R30WW Guide d'installation

dans d''autres langues

Documents connexes

Autres documents