Rinnai RUS65e series Guide d'installation

Direct Vent Tankless Water Heater

Installaon and Operaon Manual

 



 

 

 

 

 

 





WARNING



This manual provides informaon on the installaon, operaon, and maintenance of the water heater. For proper

operaon and , it is important to follow the instrucons and adhere to the safety precauons.

A licensed professional must install the water heater according to the exact instrucons in this manual.

The consumer must read the enre manual to properly operate the water heater and to have regular maintenance

performed.



FOR INDOOR APPLICATIONS ONLY

RUCS65i ................ --

RUCS75i ................ --

FOR OUTDOOR APPLICATIONS ONLY

RUS65e ................. --

RUS75e ................. --







C US

U328-0700

2 KCM Series Manual



This is the safety alert symbol. This symbol alerts you to potenal hazards that can kill or hurt you

and others.

Indicates an imminently hazardous situaon which, if not avoided, will result in personal

injury or death.

Indicates a potenally hazardous situaon which, if not avoided, could result in personal

injury or death.

Indicates a potenally hazardous situaon which, if not avoided, could result in minor or

moderate injury. It may also be used to alert against unsafe pracces.

DANGER

CAUTION

WARNING

Table of Contents ..................................................... 2

Safety Behaviors and Pracces for the

Consumer and Installer ............................................ 3



 ............................. 

Prepare for Installaon ...................................... 5

Determine Installaon Locaon ........................ 6

Freeze Protecon ............................................. 10

Checklist to Determine Installaon Locaon ... 11

Mount to Wall .................................................. 11

Remove the Front Panel .................................. 11

Installaon of Venng (indoor models only) ... 12

Determining Vent Conguraon ...................... 13

Twin Pipe PVC/CPVC Vent Installaon ............. 20

Condensate ...................................................... 37

Checklist for Venng and Condensate

(indoor models only) ........................................ 37

Installaon of Plumbing ................................... 38

Checklist for Plumbing ..................................... 41

Installaon of Gas Supply ................................ 41

Connect Electricity ........................................... 43

Adjustment for High Altude Installaons ...... 43

Adjustment for Vent Length

(indoor models only) ........................................ 43

Checklist for Gas and Electricity ....................... 43

Installaon of Temperature Controller ............ 44

Final Checklist ................................................... 46

Technical Data ........................................................ 47

Specicaons ................................................... 47

Dimensions ....................................................... 48

Pressure Drop and Water Flow Curves ............ 49

Ladder Diagram ................................................ 50

 ....................................... 

Consumer Operaon Guidelines for the

Safe Operaon of your Water Heater .................... 52

How to set the Temperature ................................. 53

How to use the Oponal Temperature

Controller ........................................................ 54

Diagnosc Codes .................................................... 56

Required Maintenance ........................................... 59

Freeze Protecon and Winterizaon ............... 60

Flushing the Heat Exchanger ............................ 61

Manual Draining of the Water Heater ............. 62

State Regulaons .................................................... 63

Replacement Parts ................................................. 64

Warranty ................................................................. 65

French Version ........................................................ 67





NOTICE: Rinnai somemes shares customer contact informaon with businesses that we believe provide

products or services that may be useful to you. By providing this informaon, you agree that we can

share your contact informaon for this purpose. If you prefer not to have your informaon shared with

these businesses, please contact customer service and ask not to have your informaon shared. We

will however, connue to contact you with informaon relevant to the product(s) you registered and/

or your account with us.

If you have any quesons or feel that the manual is incomplete contact Rinnai at 1-800-621-9419.

KCM Series Manual 3

CAUTION

 BURN HAZARD. Hot exhaust and vent may cause

serious burns. Keep away from the water heater

unit. Keep small children and animals away from

the unit.

 Hot water outlet pipes leaving the unit can be hot

to touch. In residenal applicaons, insulaon

must be used for hot water pipes below 36” due to

burn risk to children.



 Before operang, smell all around the appliance

area for gas. Be sure to smell next to the oor

because some gas is heavier than air and will sele

on the oor.

 Keep the area around the appliance clear and free

from combusble materials, gasoline, and other

ammable vapors and liquids.

 Combusble construcon refers to adjacent walls

and ceiling and should not be confused with

combusble or ammable products and materials.

Combusble and/or ammable products and

materials should never be stored in the vicinity of

this or any gas appliance.

 Always check the water temperature before

entering a shower or bath.

 To protect yourself from harm, before performing

maintenance:

 Turn o the electrical power supply by

unplugging the power cord or by turning o the

electricity at the circuit breaker. (The

temperature controller does not control the

electrical power.)

 Turn o the gas at the manual gas valve, usually

located immediately below the water heater.

 Turn o the incoming water supply. This can be

done at the isolaon valve immediately below

the water heater or by turning o the water

supply to the building.

WARNING

 Use only your hand to push in or turn the gas

control knob. Never use tools. If the knob will not

push in or turn by hand, do not try to repair it; call a

licensed professional. Force or aempted repair

may result in a re or explosion.

 Do not use this appliance if any part has been under

water. Immediately call a licensed professional to

inspect the appliance and to replace any part of the

control system and any gas control which has been

under water.

 Do not use substute materials. Use only parts

cered for the appliance.

 Should overheang occur or the gas supply fail to

shut o, turn o the manual gas control valve to the

appliance.

 Do not adjust the DIP switch unless specically

instructed to do so.

 Do not use an extension cord or an adapter plug

with this appliance.

 Any alteraon to the appliance or its controls can be

dangerous and will void the warranty.

 Proper venng is required for the safe operaon of

this appliance.

California law requires this noce to be provided:



This product contains chemicals known to the state of California to cause cancer, birth defects, or other

reproducve harm.

WARNING

4 KCM Series Manual

A licensed professional must install the appliance,

inspect it, and leak test it before use. The warranty

will be voided due to any improper installaon.

The installer should have skills such as:

 Gas sizing.

 Connecng gas lines, water lines, valves, and

electricity.

 Knowledge of applicable naonal, state, and

local codes.

 Installing venng through a wall or roof.

 Training in installaon of tankless water heaters.

(Training can be accessed on-line at

www.trainingevents.rinnai.us)



Prepare for Installaon ...................................... 5

Determine Installaon Locaon ......................... 6

Freeze Protecon ............................................. 10

Checklist to Determine Installaon Locaon ... 11

Mount to Wall .................................................. 11

Remove the Front Panel .................................. 11

Installaon of Venng (indoor models only) ... 12

Condensate (indoor models only) .................... 37

Checklist for Venng and Condensate ............ 37

Installaon of Plumbing ................................... 38

Checklist for Plumbing ..................................... 41

Installaon of Gas Supply ................................. 41

Connect Electricity ........................................... 43

Adjustment for High Altude Installaons ...... 43

Adjustment for Vent Length

(indoor models only) ........................................ 43

Checklist for Gas and Electricity ....................... 43

Installaon of Temperature Controller ............ 44

Final Checklist................................................... 46

 



 Do not install the RUCS65i, or the RUCS75i

outdoors.

 Do not install the RUS65e, or the RUS75e indoors.

 Do not install the appliance in an area where water

leakage of the unit or connecons will result in

damage to the area adjacent to the appliance or to

lower oors of the structure. When such locaons

cannot be avoided, it is recommended that a

suitable drain pan, adequately drained, be installed

under the appliance. The pan must not restrict

combuson air ow.

 Do not obstruct the ow of combuson and

venlaon air. Combuson air shall not be

supplied from occupied spaces.

 Do not use this appliance in an applicaon such as

a pool or spa heater that uses chemically treated

water . (This appliance is suitable for lling large or

whirlpool spa tubs with potable water.)

 Do not use substute parts that are not authorized

for this appliance.



 The installaon must conform with local codes or,

in the absence of local codes, with the Naonal

Fuel Gas Code, ANSI Z223.1/NFPA 54, or the

Natural Gas and Propane Installaon Code, CSA

B149.1. If installed in a manufactured home, the

installaon must conform with the Manufactured

Home Construcon and Safety Standard, Title 24

CFR, Part 3280 and/or CAN/SCA Z240 MH Series,

Mobile Homes.

 The appliance, when installed, must be electrically

grounded in accordance with local codes or, in the

absence of local codes, with the Naonal Electrical

Code, ANSI/NFPA 70, or the Canadian Electrical

Code, CSA C22.1.

 The appliance and its appliance main gas valve

must be disconnected from the gas supply piping

system during any pressure tesng of that system

at test pressures in excess of 1/2 psi (3.5 kPa)

(13.84 in W.C.).



 For installaon in residenal applicaons only.

 Cered for installaon in manufactured (mobile)

homes.





KCM Series Manual 5



Parts included

Tools needed

Materials needed

 The appliance must be isolated from the gas supply

piping system by closing its individual manual

shuto valve during any pressure tesng of the gas

supply piping system at test pressures equal to or

less than 1/2 psi (3.5 kPa) (13.84 in W.C.).

 You must follow the installaon instrucons and

those in Care and Maintenance for adequate

combuson air intake and exhaust.



 If a water heater is installed in a closed water

supply system, such as one having a backow

preventer in the cold water supply line, means

shall be provided to control thermal expansion.

Contact the water supplier or local plumbing

inspector on how to control thermal expansion.

 Should overheang occur or the gas supply fail to

shut o, turn o the manual gas control valve to

the appliance.

 Keep the air intake locaon free of chemicals, such

as chlorine or bleach, that produce fumes. These

fumes can damage components and reduce the life

of your appliance.

 Tankless water heater

 Self Tapping Screws (Qty - 2)

 Pipe wrenches (2)

 Adjustable pliers

 Screwdrivers (2)

 Wire cuers

 Gloves

 Safety glasses

 Level

Tools that might be needed

 Hammer drill with

concrete bits

 Saw

 Threading machine with

heads and oiler

 Core drill with diamond

head

 Torch set

 Copper tubing cuer

 Steel pipe cuer

Materials that may be needed

 Soap or gas leak

detector soluon

 Approved venng

 Teon tape

(recommended) or pipe

compound

 Pressure Relief Valve

 Heat tape

 Pipe insulaon

 Electrical wire and

conduit per local code

 Concrete wall anchors

 Oponal pipe cover

 Oponal temperature

controller (MC-91-2)

 PVC glue/cement

 5/8” ID PVC exible

tubing

 2 conductor 22 AWG

wire for controller

 Single gang electrical

box

 Wire nuts

 Unions and drain valves

 Isolaon Valve Kit



6 KCM Series Manual

Consideraon of care for your water heater should

include evaluaon of water quality.



















Total Hardness Up to 200 mg / L

Aluminum * Up to 0.2 mg / L

Chlorides * Up to 250 mg / L

Copper * Up to 1.0 mg / L

Dissolved Carbon Dioxide (CO2) Up to 15.0 mg / L or PPM

Iron * Up to 0.3 mg / L

Manganese * Up to 0.05 mg / L

pH * 6.5 to 8.5

TDS (Total Dissolved Solids) * Up to 500 mg / L

Zinc * Up to 5 mg / L



Environment

Air surrounding the water heater, venng, and vent

terminaon(s) is used for combuson and must be free

of any compounds that cause corrosion of internal

components. These include corrosive compounds that

are found in aerosol sprays, detergents, bleaches,

cleaning solvents, oil based paints/ varnishes, and

refrigerants. The air in beauty shops, dry cleaning

stores, photo processing labs, and storage areas for pool

supplies oen contains these compounds. Therefore it

is recommended that outdoor models be used for these

locaons where possible.

The water heater, venng, and vent terminaon(s)

should not be installed in any areas where the air may

contain these corrosive compounds. If it is necessary for

a water heater to be located in areas that may contain

corrosive compounds, the following instrucons are

strongly recommended.



Indoor/Internal Water Heaters

 DO NOT Install in areas where air for combuson

might be contaminated with chemicals.

 Before installaon, consider where air has the

ability to travel within the building to the water

heater.

 Where possible, install the water heater in a sealed

closet so that it is protected from the potenal of

contaminated indoor air.

 Chemicals that are corrosive in nature should not

be stored or used near the water heater.

Outdoor/External Water Heaters and Vent

Terminaons of Indoor/Internal Water Heaters

 Install the water heater as far away as possible

from exhaust vent hoods.

 Install as far away as possible from any air inlet

vents. Corrosive fumes may be released through

these vents when air is not being brought in

through them.

 Chemicals that are corrosive in nature should not

be stored or used near the water heater or vent

terminaon.

Damage and repair due to corrosive compounds in the

air is not covered by warranty.

Water Quality

* Source: Part 143 Naonal Secondary Drinking Water Regulaons

If you install this water heater in an area that is known

to have hard water or that causes scale build-up the

water must be treated and may require more frequent

heat exchanger ushing schedule.

When scale build-up in the heat exchanger begins to

aect the performance of the water heater, a diagnosc

code “LC#” will display. Flush the heat exchanger to

prevent damage to it. Scale build up is caused by hard

water and can be accelerated if the unit is set at a high

temperature.

Rinnai oers Southeastern Filtraon’s “ScaleCuer

Water Condioning System” that oers superior lime

scale prevenon and corrosion control by feeding a

blend of control compounds into the cold water supply.

You must ensure that clearances will be met and that

the vent length will be within required limits. Consider

the installaon environment, water quality, and need

for freeze protecon. Requirements for the gas line,

water lines, electrical connecon, and condensate

disposal can be found in their respecve installaon

secons of this manual.

Part Number Descripon

103000038

Southeastern Filtratrion

ScaleCuer System 3/4” Feed

103000039

ScaleCuer Rell

KCM Series Manual 7

INSIDE

CORNER DETAIL

FIXED

CLOSED

OPERABLE

FIXED

CLOSED

OPERABLE

B

A

J

B

M

C

F

B

E

D

L

G

A

H

K

I

[1] A vent shall not terminate directly above a sidewalk or paved driveway

that is located between two single family dwellings and serves both

dwellings.

[2] Permied only if veranda, porch, deck, or balcony is fully open on a

minimum of two sides beneath the oor.

 For clearances not specied in ANSI Z223.1/NFPA 54, clearances are in

accordance with local installaon codes and the requirements of the gas

supplier.

Clearance to opposite wall is 24 inches (60 cm).

X

V

AIR SUPPLY INLET

VENT TERMINAL

AREA WHERE TERMINAL

IS NOT PERMITTTED

For indoor models, you must install a vent terminaon to bring in combuson air and expel exhaust to the outside.

SNOW

TERMINATION

Clearance in

Ref. A also

applies to

anticipated

snow line





 

A Clearance above grade, veranda, porch, deck, or balcony 12 inches (30 cm) 12 inches (30 cm)

B Clearance to window or door that may be opened 36 inches (91 cm) 12 inches (30 cm)

C Clearance to permanently closed window * *

D

Vercal clearance to venlated sot, located above the terminal within

a horizontal distance of 2 feet (61 cm) from the center line of the

terminal

* *

E Clearance to unvenlated sot * *

F Clearance to outside corner * *

G Clearance to inside corner * *

H

Clearance to each side of center line extended above meter/regulator

assembly

3 feet (91 cm) within a height 15

feet (4.5 m) above the meter/

regulator assembly

*

I Clearance to service regulator vent outlet 36 inches (91 cm) *

J

Clearance to nonmechanical air supply inlet to building or the

combuson air inlet to any other appliance

36 inches (91 cm) 12 inches (30 cm)

K Clearance to a mechanical air supply inlet 6 feet (1.83 m)

3 feet (91 cm) above if within 10

feet (3 m) horizontally

L

Clearance above paved sidewalk or paved driveway located on public

property

7 feet (2.13 m)  *

M Clearance under veranda, porch, deck, or balcony 12 inches (30 cm)  *

Direct Vent Terminal Clearances (Indoor Units)

8 KCM Series Manual

Other Than Direct Vent Terminal Clearances (Outdoor Units)

INSIDE

CORNER DETAIL

FIXED

CLOSED

OPERABLE

FIXED

CLOSED

OPERABLE

B

A

J

B

M

C

F

B

E

D

L

G

A

H

K

I

[1] A vent shall not terminate directly above a sidewalk or paved driveway

that is located between two single family dwellings and serves both

dwellings.

[2] Permied only if veranda, porch, deck, or balcony is fully open on a

minimum of two sides beneath the oor.

 For clearances not specied in ANSI Z223.1/NFPA 54, clearances are in

accordance with local installaon codes and the requirements of the gas

supplier.

Clearance to opposite wall is 24 inches (60 cm).

X

V

AIR SUPPLY INLET

VENT TERMINAL

AREA WHERE TERMINAL

IS NOT PERMITTTED













A Clearance above grade, veranda, porch, deck, or balcony 12 inches (30 cm) 12 inches (30 cm)

B Clearance to window or door that may be opened

6 in (15 cm) for appliances ≤ 10,000 Btuh (3

kW), 12 in (30 cm) for appliances > 10,000

Btuh (3 kW) and ≤ 100,000 Btuh (30 kW), 36 in

(91 cm) for appliances >100,000 Btuh (30 kW)

4  (1.2 m) below or to side of opening;

1  (300 mm) above opening

C Clearance to permanently closed window * *

D

Vercal clearance to venlated sot, located above the terminal within a

horizontal distance of 2 feet (61 cm) from the center line of the terminal

* *

E Clearance to unvenlated sot * *

F Clearance to outside corner * *

G Clearance to inside corner * *

H

Clearance to each side of center line extended above meter/regulator

assembly

3 feet (91 cm) within a height 15 feet (4.5 m)

above the meter/regulator assembly

*

I Clearance to service regulator vent outlet 36 inches (91 cm) *

J

Clearance to non-mechanical air supply inlet to building or the combuson

air inlet to any other appliance

6 in (15 cm) for appliances ≤ 10,000 Btuh (3

kW), 12 in (30 cm) for appliances > 10,000

Btuh (3 kW) and ≤ 100,000 Btuh (30 kW), 36 in

(91 cm) for appliances >100,000 Btuh (30 kW)

4  (1.2 m) below or to side of opening;

1  (300 mm) above opening

K Clearance to a mechanical air supply inlet 6 feet (1.83 m)

3 feet (91 cm) above if within 10 feet (3

m) horizontally

L

Clearance above paved sidewalk or paved driveway located on public

property

7 feet (2.13 m)  *

M Clearance under veranda, porch, deck, or balcony 12 inches (30 cm)  *

Clearance in

Ref. A also

applies to

ancipated

snow line

KCM Series Manual 9

Addional clearances

Check to determine whether local codes supersede

these clearances.

 Avoid terminaon locaons near a dryer vent.

 Avoid terminaon locaons near commercial

cooking exhaust.

 Avoid terminaon locaons near any air inlets.

 You must install a vent terminaon at least 12

inches above the ground or ancipated snow

level.

(0.30 m) between

terminals at same

level

(1.52 m)

vercally

between

terminals

60"

V

(1.52 m)

between

terminals at

dierent levels

24"

V

(0.61 m) to wall or parapet

12"

V V

V

60"

V

RUS65e, RUS75e

RUCS65i, RUCS75i

The vent for this appliance shall not terminate

 Over public walkways; or

 Near sot vents or crawl space vents or other

area where condensate or vapor could create a

nuisance or hazard or cause property damage; or

 Where condensate or vapor could cause damage

or could be detrimental to the operaon of

regulators, relief valves, or other equipment.

for locang vent

terminaon under a sot (venlated or unvenlated

or eave vent; or to a deck or porch)

 Do not install vent terminaon under a sot vent

such that exhaust can enter the sot vent

 Install vent terminaon such that exhaust and rising moisture

will not collect under eaves. Discoloraon to the exterior of

the building could occur if installed too close.

 Do not install the vent terminaon too close under the sot

where it could present recirculaon of exhaust gases back

into the combuson air intake part of the terminaon.

2"

12 "

60"

36"

(0.91 m) to

venlated or

unvenlated sot

or eve vent; or to a

deck or porch

(1.52 m) vercally

between terminals

(50 mm) between

terminals at same level

(0.30 m) to an

inside corner

12"

36"

INSIDE

CORNER

V V

(0.30 m) between

terminals at same

level

(0.30 m ) to

an inside

corner

10 KCM Series Manual

Unit clearances











-





 6 * (152) 2 *(51)

 0 (zero) 0 (zero)

 6 (152) 6 (152)

 2 (51) 1/2 (13)

 12 (305) 12 (305)



0 (zero) 0 (zero)

* 0 inches from vent components and condensate drain

line.

The clearance for servicing is 24 inches in front of the

water heater.

For closet installaon, clearance is 6 inches (152 mm from

the front of the water heater.









-





 12 (305) 2 (51)

 0 (zero) 0 (zero)

 24 (610) 0 (zero)

 24 (610) 24 (610)

 6 (152) 1/8 (3.2)

 12 (305) 2 (51)

The clearance for servicing is 24 inches in front of the

water heater.

Freeze Protecon

Make sure that in case of freezing weather the water

heater and its water lines are protected to prevent

freezing. Damage due to freezing is not covered by

the warranty.

With electrical power and gas supplied, the water

heater will not freeze when the outside air

temperature is as cold as –22°F (-30°C) for indoor

models or is as cold as –4°F (-20°C) for outdoor

models, when protected from direct wind exposure.

Because of the “wind-chill” eect, any wind or

circulaon of the air on the unit will reduce its ability

to protect itself from freezing.

In the event of a power failure and/or gas

interrupon at temperatures below freezing the

water heater should be drained of all water to

prevent freezing damage. In addion, drain the

condensate trap and drain line.

Loss of freeze protecon may result in water damage

from a burst heat exchanger or water lines.

The unit may be drained manually. However, it is

highly recommended to:

 drain down solenoid valves be purchased and

installed that will automacally drain the unit if

power is lost. These are available in a kit,

104000059. (The condensate trap is not aected

by the auto drain down solenoid valves and will

have to be manually drained.)

 a surge protector with terminals be purchased

and installed which allows the solenoid valves to

operate if the unit is disabled due to a diagnosc

code. This is available as 104000057.

In addion, the solenoid valves should be connected

electrically to a surge protector with terminals. This

allows the solenoid valves to operate if the water

heater is disabled due to a diagnosc code.

The freeze protecon features of the water heater

will not prevent the external piping from freezing. It

is recommended that hot and cold water pipes be

insulated. Pipe cover enclosures may be packed with

insulaon for added freeze protecon.

It is recommended that the condensate trap drain line

be insulated. A frozen condensate trap results in a

diagnosc code 25.

KCM Series Manual 11



wall installaon

brackets

1. Idenfy the installaon locaon and conrm that

the installaon will meet all required clearances.

2. Securely aach the water heater to the wall

using any of the holes in the wall installaon

brackets which are at the top and boom of the

water heater. Ensure that the aachment

strength is sucient to support the weight of the

water heater. Refer to the weight of the water

heater in the Specicaons secon of this

manual.

Use a leveling tool to ensure that the water

heater is level. Proper operaon requires that

the water heater be level.





□ The water heater is not exposed to corrosive

compounds in the air.

□ The water heater locaon complies with all

required clearances.

□ For indoor models, the planned venng will not

exceed the maximum length for the number of

elbows used.

□ The planned venng terminaon/air intake

locaon meets all required clearances.

□ Indoor air is not being used for combuson.

□ The water supply does not contain chemicals or

exceed total hardness that will damage the heat

exchanger.

□ A standard 3 prong 120 VAC, 60 Hz properly

grounded wall outlet (for indoor models) or other

120 VAC, 60 Hz source is available.

□ The installaon must conform with local codes or,

in the absence of local codes, with the Naonal

Fuel Gas Code, ANSI Z223.1/NFPA 54, or the

Natural Gas and Propane Installaon Code, CSA

B149.1. If installed in a manufactured home, the

installaon must conform with the Manufactured

Home Construcon and Safety Standard, Title 24

CFR, Part 3280 and/or CAN/SCA Z240 MH Series,

Mobile Homes.

□ 







Slide the plasc trim pieces on each side of the water

heater to expose the screws.

Remove the 4 screws and pull o the front panel.

NOTICE

The water heater must be installed in an upright

posion. Do not install upside down or on its side.

12 KCM Series Manual



Install the correct venng for your model according to the venng manufacturer’s instrucons and the guidelines

below. Refer to the vent manufacturer’s technical literature for specic part numbers and instrucons.

   

Ubbink Rolux 184162PP 223176PP, 223177PP

Centrotherm InnoFlue ICRT3539 ISELL0387UV

Heat-Fab Saf-T Vent

Saf-T Vent CI Plus Wall

Terminaon

Saf-T Vent CI Plus Rain Cap

Metal-Fab Corr/Guard 3CGRVDK 3CGRVT

Ipex Concentric Kit

3”- 196006 /197009

4”-196021 /197021

3”- 196006 / 197009

4”-196021 / 197021

Ipex Low Prole Terminaon Kit —

3”- 196985

4”- 196986

Various

Manufacturers

Schedule 40 PVC DWV Solid

Core Pipe (or approved equal)

CPVC schedule 40

Reference “Approved PVC/CPVC

Vent Conguraons” Table

Reference “Approved PVC/

CPVC Vent Conguraons”

Table







  

Ubbink

Rolux Condensing

Vent System

800-621-9419 678-829-1666 www.rinnai.us

Centrotherm

InnoFlue Vent System (single

wall SW, 3 inch diameter)

877-434-3432 518-618-3166

info@centrotherm.us.com

www.centrotherm.us.com

Heat-Fab Saf-T Vent SC system 800-772-0739 413-863-4803

custsvc@heat-fab.com,

www.heaab.com

Metal-Fab

Corr/Guard Vent/Air Intake

System

800-835-2830 316-943-2717

[email protected]m,

www.metal-fabinc.com

Ipex

Concentric Kit / Low Prole

Terminaon Kit

U.S. - 800-463-9572

CA. - 866-473-9462

—

www.ipexamerica.com

www.ipexinc.com

Various

Manufacturers

Schedule 40 PVC DWV Solid Core

Pipe (or approved equal)

CPVC schedule 40

— — —

Approved Vent Manufacturers

Approved Vent Products



KCM Series Manual 13

Venng Guidelines



 Do not use cellular core PVC/CPVC.

 Do not use Radel, ABS, or galvanized material to

vent this appliance.

 Do not cover non-metallic vent pipe and ngs

with thermal insulaon.

 Do not combine vent components from dierent

manufacturers.

 Vent diameter must not be reduced.

 Do not connect the venng system with an

exisng vent or chimney.

 Do not common vent.



 This water heater is a direct vent water heater and

therefore is cered and listed with the vent

system. You must use vent components that are

cered and listed with the water heater model.

 The vent system must vent directly to the outside

of the building and use outside air for combuson.

 Avoid dips or sags in horizontal vent runs by

installing supports per the vent manufacturer’s

instrucons.

 Support horizontal vent runs every four feet and

all vercal vent runs every six feet or in

accordance with local codes.

 Venng should be as direct as possible with a

minimum number of pipe ngs.

 Vent connecons must be rmly pressed together

so that the gaskets form an air ght seal.

 The vent piece connected to the water heater

must be secured with one self-tapping screw.



 Refer to the instrucons of the vent system

manufacturer for component assembly

instrucons.

 If the vent system is to be enclosed, it is suggested

that the design of the enclosure permit inspecon

of the vent system. The design of such enclosure

shall be deemed acceptable by the installer or the

local inspector.



If it becomes necessary to access an enclosed vent

system for service or repairs, Rinnai is not responsible

for any costs or dicules in accessing the vent

system. The warranty does not cover obtaining

access to a vent system in an enclosed environment.



 

Concentric OFF

Twin Pipe ON



Prior to the installaon of the vent system, the dip

switches on the PCB board must be properly set for

the venng conguraon selected for the applicaon.

(Unit comes defaulted for concentric applicaons)



-

-





14 KCM Series Manual



 Prior to the installaon of the vent system, the

unit must be properly adjusted for the venng

conguraon selected for the applicaon.

 Any issues resulng from improper installaon

will not be covered by warranty.

 Ducted outside air is mandatory for all twin pipe

conguraons.

NOTICE

Exhaust Adapter

Ring to be removed

and discarded for

concentric vent

conguraon

Concentric Vent Conguraon

(Same procedure to be used for Twin Pipe with

Centrotherm Adapter Conguraon)

Removal of Exhaust Adapter Ring

1. Remove fastener from concentric ue

connecon.

2. Remove exhaust adapter ring.

3. Install the concentric vent. Ensure it is properly

seated.

4. Secure the vent pipe to the unit with a screw

KCM Series Manual 15

Intake Cap to be removed and discarded

for twin pipe PVC/CPVC conguraon.



Removal of Intake Cap

1. Remove the fastener from intake connecon.

2. Remove the intake cap.

Twin Pipe PVC/CPVC Conguraon

(3”or 4”)

3. Install the intake pipe. Ensure it is properly

seated.

4. Secure the intake pipe to the unit with the

supplied screw (in the carton box).

5. Install the exhaust pipe. Ensure it is properly

seated.

6. Secure the exhaust pipe to the unit with the

supplied screw (in the carton box).



apply PVC glues, solvents, or cleaners

to the water heaters intake or exhaust gasket

connecons. Failure to correctly assemble the

components according to these instrucons

may result in property damage, personal injury,

or death.

Intake Gasket Connecon

Exhaust Gasket Connecon

16 KCM Series Manual

Maximum vent length



1. Determine the number of 90 degree elbows in

the vent system. (Two 45 degree elbows count as

one 90 degree elbow.)

2. Refer to the table to nd the maximum vent

length based on the number of elbows.

3. Adjust SW1 in DIPSW 1 (tan switches) if required

by the applicable note.

 If the length is greater than 21  (6.4 m) then

move SW1 to OFF.

 If the length is greater than 15  (4.6 m) then

move SW1 to OFF.

 If the length is greater than 9  (2.7 m) then move

SW1 to OFF.

 Move SW1 to OFF.

Example: If you have one elbow then your maximum

vent length is 35 feet (10.7 m). If your

actual length is greater than 15  (4.6 m)

then move SW1 in DIPSW 1 to OFF.

If you have a longer vent length (see number 3

regarding max. vent length), SW1 in DIPSW 1 is

required to be in the OFF posion. This ensures the

water heater will run properly. Blocked ue

diagnosc codes and shutdowns may result if SW1 in

DIPSW 1 is not in the correct posion.





(Intake is the short UV protected 90° elbow)

















If length is greater

than:

0 41  (12.50 m)

18  (5.49 m) move

SW1 to OFF

1 26  (7.93 m)

3  (0.91 m) move SW1

to OFF

2 11  (3.35 m)

move SW1 to OFF for

any length

















If length is greater

than:

0 41  (12.50 m) 21  (6.40 m) move

1 35  (10.67 m) 15  (4.57 m) move

2 29  (8.84 m) 9  (2.74 m) move

3 23  (7.01m) 3  (0.91 m) move

4 17  (5.18 m)

move SW1 to OFF

for any length

5 11  (3.35 m)

6 5  (1.52 m)



(Intake is the long UV protected 90° elbow)



InnoFlue Vent System (single wall SW, 3 inch diameter)



(90° elbow is equivalent to 6 feet; 45° elbow is equivalent to 3 feet.)









0 41 (12.5)

1

1 35 (10.7)

2

2 29 (8.8)

3

3 23 (7.0)

4

4 17 (5.2)

4

5 11 (3.4)

4

6 5 (1.5)

4

KCM Series Manual 17

Maximum vent length



(90° elbow is equivalent to 5 feet; 45° elbow is equivalent to 2.5 feet.)









0 41 (12.5)**

1 36 (11.0) **

2 31 (9.4) **

3 26 (7.9) **

4 21 (6.4) **

5 16 (4.9) **

6 11 (3.4) **

**SW 1 in DIPSW 1 is “OFF” for lengths greater than

or equal to 21 feet.



(90° elbow is equivalent to 5 feet; 45° elbow is equivalent to 2.5 feet.)









0 100 (30.5)**

1 95 (29.0) **

2 90 (27.4) **

3 85 (25.9) **

4 80 (24.4) **

5 75 (22.9) **

6 70 (21.3) **



(See Twin Pipe PVC/CPVC Vent Installaon secon for

more informaon regarding equivalent vent length

calculaons.)

18 KCM Series Manual

Flue Installaon with Concentric Venng (indoor models only)

Install the venng terminaon according to the diagrams and instrucons below.

Secure the first vent component to the water heater

with one self-tapping screw at the hole.





Slope the venting 1/4” per foot toward the

appliance according to the vent manufacturers

installation instructions.

Dispose of condensate per local codes.

Securing Screw

Slope the venting 1/4” per foot toward the

appliance according to the vent manufacturers

installation instructions.

Dispose of condensate per local codes.

KCM Series Manual 19

 Comply with the exhaust clearances found in this Rinnai Installaon and Operaon Manual.

 Only one appliance can be aached to the vent system.

 Install the system according to the Centrotherm installaon instrucons included with the vent system.

 The vent terminaon and air intake must be in the same pressure zone.

 Do not exceed the maximum straight vent length with number of elbows as shown in the tables in the

following secon.

 Maintain the clearances shown in the gures below.



The following vent materials are for use with this appliance:

 Cellular core PVC/CPVC

 Radel, ABS, and/or Galvanized ducts.

Failure to use approved vent materials can result in property damage, personal injury, or death.



Flue Installaon with Centrotherm Venng (indoor models only)

Install the venng terminaon according to the diagrams and instrucons below.



11”

5”

Intake

Oponal

Vent

Slope horizontal exhaust run towards the water heater 1/4” per foot. slope combuson air pipe towards unit. Be

sure to dispose of condensate per local codes.

20 KCM Series Manual

Installaons must comply with local requirements and with the Naonal Fuel Gas Code, ANSI Z223.1/NFPA 54 for U.S.

installaons or CSA B149.1 for Canadian installaons.  use cellular core PVC, CPVC, or Radel based pipe materials

for the exhaust vent. Vents  be of solid core pipes ONLY.



Use only the materials listed in this secon for vent, air intake pipe, and ngs (See vent and air piping materials table).

Failure to comply with this warning could result in property damage, personal injury, or death.



Twin Pipe PVC/CPVC Vent Installaon

La page charge ...

Rinnai RUS65e series Guide d'installation

Rinnai RUS65e series Guide d'installation

dans d''autres langues

Documents connexes

Autres documents