WilsonPro Pro 70 Plus (50Ω) Guide d'installation

Marque: WilsonPro

Modèle: Pro 70 Plus (50Ω)

Catégorie: Amplificateurs de signal cellulaire

Taper: Guide d'installation

ENGLISH

FRANÇAIS

Contents:

How Cellular Boosters Work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Install Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Kit Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Installation Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 & 4

Outside Antenna Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installing the Inside Panel Antenna(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Installing The Signal Booster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Finding The Strongest Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Post Install Setup / LCD Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Warnings and Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back

Note: This manual contains important safety and operating information. Please read and follow the

instructions in this manual. Failure to do so could result in damage to your Signal Booster.

Appearance of device and accessories may vary.

INSTALLATION GUIDE

In-Building

SmarTech

Cellular Signal Boosters

PRO 70 PLUS

™

-50 Ohm

PRO SERIES

Contact Wilson Electronics Customer Support Team with any questions at

866-839-9361 or email: [email protected]

ENGLISH

1. Select a location on the roof or outside of the building to install the outside antenna. Refer

to pages 3 & 5.

2. Select a location to install the Signal Booster that is away from excessive heat,

direct sunlight or moisture, and has adequate ventilation. Airtight enclosures are not

recommended. Booster should be as close to the outside antenna as possible in order to

minimize losses from cable length to outside antenna.

3. Connect the cable from the outside antenna to the signal booster’s “outside antenna”

Install Overview

Refer to Installation Diagram on page 3 & 4. Contact Wilson Electronics Technical Support

Team with any questions at 866-839-9361.

How a Cellular Booster Improves Indoor Signals

Wilson cellular signal booster systems work as follows: an outdoor antenna placed

on a

building where some cell signal is present, (ideally on a roof or pole), receives and sends

that weak signal via coax cable (like used in satellite TV installs) to a signal booster located

indoors. That weak signal is amplified by the booster and delivered via coax cable to an

inside antenna(s) which rebroadcasts the amplified signal within one or several areas where

improved signal is required. Signals from indoor cell device(s) are likewise picked up by the

inside antenna(s), amplified by the signal booster and transmitted back to the cell tower via

the outside antenna. The improved signals result in reliable cellular connections

for indoor users.

About Gain and Improved Signal Area

The less signal strength at the outside antenna’s location and/or the greater the coverage

need, the more gain will be required. Conversely, the more signal present outside, the

greater the inside coverage area will be. Proper aiming of the outside antenna towards the

source of the cell signal is also important. The gains of the outside and inside antenna,

though reduced by losses from coax cable lengths, also affect area of improved coverage.

Placement of the inside antenna is also a factor as they have directional characteristics.

Inside wall materials will also affect indoor coverage area.

Another important factor affecting coverage area is inadequate isolation between outside

and inside antenna(s). Wilson boosters are designed to reduce their internal gain in

order to prevent any feedback “oscillations” which if unchecked, could affect nearby cell

site operation. The LCD status display on the booster is used to determine if a booster

is operating at optimal gain for each cellular band. Optimal gain can be achieved by

increasing antenna separation, i.e. isolation, until the max gain is indicated. If attainable

separation is limited by a building’s layout, gain will suffer. A nearby cell site, even if not

providing service to a user, can also cause the booster’s automatic network protection

circuitry to reduce gain or even turn off one or more of the booster’s bands so as to

prevent signal overload to the nearby site. The display on the booster can also be used

to determine if this condition is taking place. Refer to pages 9-11 for explanation of the

booster status display.

Contact Wilson Electronics Customer Support Team with any questions at

866-839-9361 or email: [email protected]

ENGLISH

connector. Refer to page 6 for more information on running cable. Lightning Surge

Protection is recommended for all in-building installations. Refer to pages 3 & 6.

4. Select a location for the inside antenna. Try to choose a position in the center of the area

needing improved signal. Keep in mind that proper inside antenna to outside antenna

isolation is necessary for the system to function properly. This may require as much as

50 to 75 feet of horizontal separation from the outside antenna. Vertical separation

also helps increase isolation. Alternate means of isolation are possible. If physical

separation is not possible, please contact Wilson Electronics Tech Support at

866-839-9361 for suggestions on alternate methods to achieve isolation.

5. Connect the cable from the inside antenna to the signal booster’s “inside antenna”

connector. Refer to page 6 for more information on running cable. Keep cable runs as

short as possible to reduce signal loss in the system.

6. Before powering up the signal booster, verify that both the outside antenna and the

inside antenna are connected correctly, and check that all connections are tight. Note:

Be careful when plugging the connectors in so as not to bend the center pins on the

connectors.

7. Power on the signal booster by plugging in the included power supply. If the lights are

not green, please refer to pages 10-11.

Pro 70 Plus

2’ LMR 400 Lightning Surge

Protector

Wide Band Directional

Antenna 75’ LMR 400

Wide Band Panel Antenna

60' LMR 400

463127 Kit

463227 Kit

Pro 70 Plus

AC/DC

Power Supply

12V/3A

2’ LMR 400 Lightning Surge

Protector

Wide Band Directional

Antenna 75’ LMR 400

463327 Kit

Pro 70 Plus

2’ LMR 400 Lightning Surge

Protector

4G Dome Ceiling Antenna

60’ LMR400 Cable

4G Dome Ceiling Antenna

60’ LMR400 Cable

e Ceiling Anten

Multiple Kit Options Available Note: Kits may contain diﬀ erent accessories

To purchase Expansion Kits call Wilson Electronics Sales Department at: 888-503-5329

4G Omni Plus

Antenna 75’ LMR400

Cable

AC/DC

Power Supply

12V/3A

AC/DC

Power Supply

12V/3A

Contact Wilson Electronics Customer Support Team with any questions at

866-839-9361 or email: [email protected]

ENGLISH

pport Team with an

questions a

@il l t i

Installation Diagram

Outside Antenna

(Wide Band Directional

Antenna shown)

Inside Antenna

Power Supply

Inside Antenna

Preferred Method: Place the

Inside Antenna in the ceiling

facing down for the best

coverage.

Note: A Wilson Lightning Surge Protector

(859902) is recommended for all building

installations. Make sure the protector is

installed outside the building at point of entry

connected to a suitable ground and in line

between the Outside Antenna and the Signal

Booster.

Surge Protector

Power Strip

pacing

ritical

Contact Wilson Electronics Customer Support Team with any questions at

866-839-9361 or email: [email protected]

ENGLISH

ontact Wilson Electronics

ustomer

upport Team with an

questions a

866 839 9361 il t h@ il l t i

GLIS

Signal

Booster

Optional Inside

Antenna for added

coverage

Optional Splitter

2-way or 3-way, when using

multiple inside antennas for

increased coverage

Contact Wilson Electronics Customer Support Team with any questions at

866-839-9361 or email: [email protected]

ENGLISH

Cell Tower

Wide Band Antenna

Selecting a Location for the Outside Antenna

The outside antenna must be mounted at a location outside of the home or building, where the

strongest cell signal is present. This can be accomplished by using the Wilson Signal Meter.

Alternatively, a cell phone in test mode can be used for finding the area around the building

with the strongest signal.

Mount the outside antenna as high as possible facing towards the suspected location of the

cell tower and pointing away from the expected location of the inside antenna(s).

Outside Antenna Installation

The antenna should be mounted as shown in Figure 1. The mounting bracket, included with

antenna, is adjustable and will accommodate pipe diameters from 1.25 inches to 2 inches

(pipe sold separately #901117). Mount the antenna so that there is at least 3 feet of clearance

in all directions around it. Make sure the antenna is not pointing across your own roof or at

the inside antenna as this will cause the cell site protection circuitry to shut down the signal

booster.

Signal Booster

Outdoor

Antenna

Outdoor

Antenna

Inside

Antenna

Figure 1

Figure 2

CORRECT INSTALLATION

Never point antennas toward each otherPoint antennas away from each other

INCORRECT INSTALLATION

Inside

Antenna

Signal Booster

Contact Wilson Electronics Customer Support Team with any questions at

866-839-9361 or email: [email protected]

ENGLISH

Warning:

Lightning protection is recommended for all installations (#859902-

50 Ohm, shown below). Take extreme care to ensure that neither

you nor the antenna comes near any electric power lines.

Installing Lightning Protection

Install the Lightning Surge Protector (LSP) outside, in line with the coax cable from the outside

antenna, near where the coax cable from the outside antenna will enter the building. Connect

the Outside antenna cable to one of the connectors of the surge protector. Connect the other

connector on the LSP to the cable entering the building. Ensure the LSP is properly grounded

as close to the LSP as possible (ground wire not included).

Running Outside Antenna Cable

If you are mounting the outside antenna to the outside wall of your home or building, the

simplest way is to run the cable on the outside of the wall and attach it to the exterior of your

home or office. Then drill a hole through the wall where you want the cable to appear on the

inside of the building. Before drilling, make sure that there are no electrical outlets, sewer

or water pipes, or electrical wiring in the wall that you are about to drill through as this could

potentially harm you or damage the building. Note: Existing TV cables already being used

for another purpose can not be shared with the cell booster installation.

After drilling the required hole, run the cable through and seal it with cable bushings or a

silicone-type sealant to enclose the hole that you have created. In some instances, it may be

possible to run the cable up into the fascia of the attic overhang. In this circumstance, the cable

will be accessible in the attic for further routing.

Exterior wall of building or home

Lightning

Surge Protector

Signal Booster

Surge Protector Power Strip

To Outside

Antenna

Ground Wire

To Inside

Antenna

Contact Wilson Electronics Customer Support Team with any questions at

866-839-9361 or email: [email protected]

ENGLISH

Installing the Inside Panel Antenna(s)

Select a location for the inside antenna, preferably in the center of where the signal needs

to be amplified. A minimum separation distance of 20 vertical feet and or 50 horizontal feet

between the inside and outside antenna(s) may be necessary in order to achieve full booster

gain and therefore maximum indoor coverage. If the amplifier can not be set to maximum

gain as explained on page 10, you may need as much as 75 feet of horizontal separation, or

mechanical isolation, between inside and outside antennas. Refer to installation diagram on

pages 3 & 4.

Ceiling

Rafters

Ceiling

Drywall

Inside

Antenna

Some installations requiring signal improvement in far areas of larger homes or structures

may require multiple inside antennas and splitter(s). For example if signal is improved

in most areas of a structure, but yet there is weak signal In another area, the signal from

the booster can be split to two or more separate indoor antennas by using a splitter (sold

separately). Refer to the configuration on pages 3 & 4.

Additional Inside Panel

Antenna w/ cable

sold separately

Multiple mounting options

available

For additional antenna options

see pages 14 & 15

Splitter Options:

Installing the Signal Booster

Select a location for the signal booster which is away from excessive heat, direct sunlight,

moisture and is not subject to high temperatures. Do not place the signal booster in an air-tight

enclosure. Recommended installation locations for in-building signal boosters are in a closet or on

a shelf where power is available. Attic installations may expose the booster to high heat.

2-way 3-way 4-way

Splitter

Optio

Contact Wilson Electronics Customer Support Team with any questions at

866-839-9361 or email: [email protected]

ENGLISH

Note: Do not install in areas subject to temperatures in excess of 150 °F.

Note: Maintain at least 6 inches of clearance from surrounding objects. Be careful when plugging

the connector in so as not to damage the center pins on the connectors.

Run the outside antenna cable to the signal booster and attach it to the connector labeled

“Outside Antenna” on the signal booster. Run the inside antenna cable to the signal booster and

attach it to the connector labeled “Inside Antenna” on the signal booster.

Note: In order to abide by FCC regulations, cable lengths and antennas shipped as a kit with each

booster must be used and not cut and shortened. Contact our tech support for cable kits to be used

in situations requiring long cable runs.

Note: It is very important to power your signal booster using a surge protected AC power strip with

at least a 1000 Joule rating. Failure to do this will void your warranty in the event of a power surge

or lightning strike.

Finding the Strongest Signal

When installing your signal booster’s outside antenna, aiming it towards the best signal

source from your carrier is important. The best way of getting the strongest signal is to

use the Wilson Signal Meter and accessory Directional Antenna (see outside antenna

kit options on page 14), an alternate way is to have one person on the roof to rotate the

outside antenna, which is connected to the signal booster. Turn the outside antenna about

45 degrees at a time, while the second person, inside the building, is watching the signal

strength on a signal meter (preferred) or a phone in test mode. This allows you to read the

signal strength from the cell tower. The phone should be in the test mode so the actual

signal strength can be read, as bars are not the most accurate. Always make sure the

person inside the building gives the signal strength time to register on the phone (at least

30 seconds for phone to update the signal reading).

-50 dBm0 dBm -60 dBm -70 dBm -80 dBm -90 dBm -100dBm -110dBm

EXCELLENT GOOD POOR NO

SIGNAL

Signal Strength Graph

Cell Tower

Cell Signal

Outside

Antenna

Signal readings usually appear as a negative number (for example, -86). The closer the

number to zero, the stronger the signal (see Signal Srength Graph above).

Contact Wilson Electronics Customer Support Team with any questions at

866-839-9361 or email: [email protected]

ENGLISH

Post Install Setup

The Pro Series booster is designed with advanced internal programming which allows it to

automatically adjust itself for a variety of conditions and still boost weak signals. After completing

the amplifier installation, the LCD display and push button on the lower panel of the Pro Series

booster is used to verify the final gain that the booster adjusted itself to produce after antennas

have been placed. The display can also be used (if necessary) to re-adjust antennas so the

booster can produce maximum gain and therefore, coverage. The LCD screen will show status

for each band and inform the installer if any bands may have had their gain reduced by the

booster’s internal programming. In addition, an indicator light on the booster's upper panel will

help diagnose the overall status of the booster by glowing in different colors. This will be covered

in the following page.

The Pro Plus booster has an integrated graphical meter to simplify the installation process. This is

not to replace your signal meter - rather it complements the use. The bar graphs will assist in the

aiming of your outside antenna - the biggest graph indicates that you are receiving the best overall

signal.

To access this feature for the currently displayed frequency band, press and hold the "Band

Select" button for 2 seconds. This will change the display to the UL/DL bar graph (uplink/

downlink). A quick press of the button will move to the next band (briefly showing the band, before

returning back to the bar graph); while holding the button will return to the regular display.

press and hold

for 2 seconds

Understanding the LCD Screen

1. Four bands can be individually selected:

The 700 MHz LTE Bands (B12/17 and B13)

Contact Wilson Electronics Customer Support Team with any questions at

866-839-9361 or email: [email protected]

ENGLISH

The 800 MHz Band

– Cell Band

The 1900 MHz

– PCS Band

1700/2100 MHz

– AWS Band

The single “BAND SELECT” button is used to scroll the display through the four

cellular bands in order to verify that each band is functioning properly. An asterisk (located next

to the band selected) will flash if one or more bands have been turned down/off by the boosters

control circuitry due to strong nearby cell site signal overload (“OVL”) and/or oscillation detection

(“OSC”) from antennas being too close. This is no cause for concern if the power light remains

green and you are satisfied with your indoor coverage area.

Understanding the Upper Panel Indicator Light

As the LCD display is being toggled through the four cellular bands, the upper indicator

light (power) will glow green, orange, or red on each selected band, depending on how the

booster is functioning on each band as explained below.

PRO 70 PLUS

Green indicates the unit is powered and working properly.

Red indicates the booster has shut down due to extreme oscillation (feedback).

Orange indicates the booster has shut down due to extreme signal overload. This is caused

from being too close to a cell tower.

Contact Wilson Electronics Customer Support Team with any questions at

866-839-9361 or email: [email protected]

ENGLISH

Fixing Red Light Issues

If the power light is red:

1. Make sure all connections are tight.

2. You need to increase the distance between the outside antenna and the inside antenna

by moving them horizontally and/or vertically farther apart. After doing so, reset the

booster by unplugging the power supply and then plugging it back in. If the light is

green after separating the antennas, you have eliminated the problem.

3. If your coverage area is still too small after separating the antennas contact the Wilson

Electronics Customer Support Team for assistance: 866-839-9361.

Fixing Orange Light Issues

If the power light is orange:

1. It will be necessary to turn the outside antenna away from the nearby cellular signal

in small increments until the light turns green. If the Signal Booster will not respond,

relocation of the outside antenna may be required.

2. If the light remains orange, contact the Wilson Electronics Customer Support Team for

assistance at 866-839-9361.

Contact Wilson Electronics Customer Support Team with any questions at

866-839-9361 or email: [email protected]

ENGLISH

About Wilson Electronics

Wilson Electronics, LLC has been a leader in the wireless communications industry for over

40 years. The company designs and manufactures Signal Boosters, antennas and related

components that significantly improve cellular telephone signal reception and transmission

in a wide variety of applications, mobile (marine, RV, vehicles) and in-building (home, office,

machine to machine).

With extensive experience in antenna and Signal Booster research and design, the company’s

engineering team uses a state-of-the-art testing laboratory, including an anechoic chamber

and network analyzers, to fine-tune antenna designs and performance. For its Signal Boosters,

Wilson Electronics uses a double electrically shielded RF enclosure and cell tower simulators

for compliance testing.

Wilson Electronics Signal Boosters feature patented SmarTech

that enables them to

automatically adjust their power based on cell tower requirements. By detecting and preventing

oscillation (feedback), signal overload and interference with other users, these SmarTech

Signal Boosters improve network cell phone areas without compromising carrier systems.

All products are engineered and assembled in the company’s 100,000 square-foot

headquarters in St. George, Utah. Wilson Electronics has product dealers in all 50 states as

well as in countries around the world.

Contact Wilson Electronics Customer Support Team with any questions at

866-839-9361 or email: [email protected]

ENGLISH

Warnings and Recommendations

WARNING: To uphold compliance with network protection standards, all active

cellular devices must maintain at least 6 feet of separation distance

from Panel and Dome antennas.

WARNING: Connecting the Signal Booster directly to the cell phone with use of an

adapter will damage the cell phone.

WARNING: Use only the power supply provided in this package. Use of a non-

Wilson Electronics product may damage your equipment.

WARNING: The Signal Booster unit is designed for use in an indoor, temperature-

controlled environment (less than 150 degrees Fahrenheit). It is not

intended for use in attics or similar locations subject to temperatures

in excess of that range.

WARNING: Warning: The Outside Antenna must be installed no higher than 10

meters (31’9”) above ground.

WARNING: Take care to ensure that neither you nor the pole comes near any

power lines during installation.

RF SAFETY WARNING: Any antenna used with this device must be located at least

8 inches from all persons.

This is a CONSUMER device.

BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and

have your provider’s consent. Most wireless providers consent to the use of signal

boosters. Some providers may not consent to the use of this device on their network. If

you are unsure, contact your provider.

In Canada, BEFORE USE you must meet all requirements set out in ISED CPC-2-1-05.

You MUST operate this device with approved antennas and cables as speciﬁ ed by the

manufacturer. Antennas MUST be installed at least 20 cm (8 inches) from (i.e., MUST

NOT be installed within 20 cm of) any person.

You MUST cease operating this device immediately if requested by the FCC (or ISED in

Canada) or licensed wireless service provider.

WARNING. E911 location information may not be provided or may be inaccurate for calls

served by using this device.

This device may be operated ONLY in a ﬁ xed location (i.e..may operate in a ﬁ xed loca-

tion only) for in-building use.

Contact Wilson Electronics Customer Support Team with any questions at

866-839-9361 or email: [email protected]

ENGLISH

Note: For a complete list of antennas and cables approved for use with these boosters see

pages 14 & 15.

This device complies with Part 15 of FCC rules. Operation is subject to two conditions: (1) This device may not cause

harmful interference, and (2) this device must accept any interference received, including interference that may cause

undesired operation. Changes or modifications not expressly approved by Wilson Electronics could void the authority to

operate this equipment.

Inside Antenna Expansion Kit

(contact Wilson Technical Support for assistance)

Kit 309900-50N

2 - Wall Panel antennas

1 - 50 ohm 3-Way Splitter

Kit 309905-50N

3 - Wall Panel Antennas

3 - 2-Way 50 Ohm Splitters

Kit 309902-75F

2 - Wall Panel Antennas

1 - 3-Way 75Ohm Splitter

Kit 309903-75F

3 - Wall Panel Antennas

3 - 2-Way 75Ohm Splitters

Kit 309904-75F

1 - Wall Panel Antenna

1 - 2-Way 75 Ohm Splitter

Inside Antenna Kits

(contact Wilson Technical Support for assistance)

Kit 311155-0630

75 Ohm Wall Mount Panel Antenna

30’ RG6

Kit 311135-5820

50 Ohm Wall mount Panel Antenna

20’ RG58 Cable

Kit 311135-40060

50 Ohm Wall Mount Panel Antenna

60’ LMR400 Cable

Kit 311155-1150

75 Ohm Wall mount Panel Antenna

50’ RG11 Cable

Kit 304412-40010

50 Ohm 4G Dome Antenna

10' Wilson400 cable

Kit 304412-5810

50 Ohm 4G Dome Antenna

10' RG58 cable

Kit 304419-1110

75 Ohm 4G Dome Antenna

10' RG 11 cable

Kit 304419-17410

75 Ohm 4G Dome Antenna

10' RG174 cable

*May need separate adapter

Kit 304419-0610

75 Ohm 4G Dome Antenna

10' RG6 cable

Kit 301213

Desktop Antenna w/ 5' RG174

50 Ohm Outside Antenna Kits

(contact Wilson Technical Support for assistance)

Kit 314453-5825

50 Ohm Pole Mount Panel Antenna

25’ RG58 Cable

Kit 314411-5825

50 Ohm Wide Band Directional

25’ RG58 Cable

Kit 301111-5850

Yagi Directional Antenna

50’ RG58 Cable

Kit 311203-5820

Omni-Directional antenna

20’ RG58 Cable

Kit 311203-40020

Omni-Directional antenna

20’ LMR400 Cable

Kit 301111-400170

Yagi Directional w/ N-Female

170’ LMR400

Kit 314411-40075

50 Ohm Wide Band Directional Antenna

75’ LMR400 Cable

Kit 314453-40075

50 Ohm Pole Mount Panel Antenna

75’ LMR400 Cable

Kit 304422-40020

50 Ohm 4G Omni Antenna

20' Wilson400 cable

Kit 304422-5810

50 Ohm 4G Omni Antenna

10' RG58 cable

Contact Wilson Electronics Customer Support Team with any questions at

866-839-9361 or email: [email protected]

ENGLISH

Kit 304422-1120

50 Ohm 4G Omni Antenna

20' RG11 cable

*May need separate adapter

75 Ohm Outside Antenna Kits

(contact Wilson Technical Support for assistance)

Kit 301111-0675

Yagi Directional Antenna

75’ RG6 Cable

N-Male to F-Female adapter

Kit 311201-0620

Omni Directional w/ F-Female

20’ RG6 Cable

Kit 311141-0620

75 Ohm Grey Brick Antenna

20’ RG6 Cable

Kit 301111-11140

Yagi Directional Antenna

140’ RG11 Cable

N-Male to F-Female adapter

Kit 311201-1120

Omni Directional w/ F-Female

20’ RG11 Cable

Kit 314473-1175

75 Ohm Pole Mount Panel Antenna

75’ RG11 Cable

Kit 314475-1175

75 Ohm Wide Band Directional

75’ RG11 Cable

Kit 311141-1120

75 Ohm Grey Brick Antenna

20’ RG11 Cable

Kit 304421-1120

75 Ohm 4G Omni Antenna

20' RG 11 cable

Kit 304421-17410

75 Ohm 4G Omni Antenna

10' RG174 cable

Kit 304421-0610

75 Ohm 4G Omni Antenna

10' RG6 cable

Kit 304421-5810

75 Ohm 4G Omni Antenna

10' RG58 cable

*May need separate adapter

Mini-Mag Outside Antenna

(contact Wilson Technical Support for assistance)

301126 w/12.5 RG174 cable-SMA

Contact Wilson Electronics Customer Support Team with any questions at

866-839-9361 or email: [email protected]

ENGLISH

30-Day Money-Back Guarantee

All Wilson Electronics products are protected by Wilson Electronics 30-day money-back guarantee. If for any reason

the performance of any product is not acceptable, simply return the product directly to the reseller with a dated proof of

purchase.

3-Year Warranty

Wilson Electronics Signal Boosters are warranted for three (3) years against defects in workmanship and/or materials.

Warranty cases may be resolved by returning the product directly to the reseller with a dated proof of purchase.

Signal Boosters may also be returned directly to the manufacturer at the consumer’s expense, with a dated proof of

purchase and a Returned Material Authorization (RMA) number supplied by Wilson Electronics. Wilson Electronics

shall, at its option, either repair or replace the product. Wilson Electronics will pay for delivery of the repaired or replaced

product back to the original consumer if located within the continental U.S.

This warranty does not apply to any Signal Booster determined by Wilson Electronics to have been subjected to

misuse, abuse, neglect, or mishandling that alters or damages physical or electronic properties.

Replacement products may include refurbished Wilson Electronics products that have been recertified to conform with

product specifications.

Failure to use a surge protected AC Power Strip with at least a 1000 Joule rating will void your warranty.

RMA numbers may be obtained by contacting Customer Support at 866-294-1660.

Disclaimer : The information provided by Wilson Electronics, LLC is believed to be complete and accurate.

However, no responsibility is assumed by Wilson Electronics, LLC for any business or personal losses arising from

its use, or for any infringements of patents or other rights of third parties that may result from its use.

U.S. Patent Nos. – 7,221,967; 7,729,669; 7,486,929; 7,409,186; 7,783,318; 8,583,034; 8,583,033; 8,874,030 B2;

8,874,029 B2; 8,755,399; 8,849,187 B2; 8,639,180; D703, 181

Contact Wilson Electronics Customer Support Team with any questions at

866-839-9361 or email: [email protected]

ENGLISH

Notes

Contact Wilson Electronics Customer Support Team with any questions at

866-839-9361 or email: [email protected]

ENGLISH

Notes

Signal Booster Specifications

Pro 70 Plus™ 50 Ohm

Model Number 463027

FCC ID

PWO460027

IC ID

4726A-460027

Connectors N-F

emale

Antenna Impedance 50 Ohms

Frequency 698-716 MHz, 746-787 MHz, 824-894 MHz, 1850-1995 MHz, 1710-1755/2110-2155 MHz

Passband Gain (nominal)

700

MHz Band12/17

59.1

700MHz Band13

56.2

800MHz

59.2

1700/2100MHz

64.8

1900MHz

67.8

20 dB Bandwidth (MHz)

700

MHz Band12/17 700

MHz Band13 800MHz 1700/2100MHz 1900MHz

Typical

Maximum

29.9

34.4

28.6

34.4

38.7

40.3

82.6

85.0

81.8

85.9

Power output for single cell

phone (Uplink) dBm

700

MHz Band12/17 700MHz Band13 800MHz 1700MHz 1900MHz

20.4 20.82 25.16 23.0 21.42

Power output for single cell

phone (Downlink) dBm

700

MHz Band12/17 700MHz Band13 800MHz 2100MHz 1900MHz

11.57 10.41 9.4 11.3 9.47

Power output for multiple

received channels (Uplink) dBm

No. Tones

700

MHz Band12/17 700MHz Band13 800MHz 1700MHz 1900MHz

2 18.0 17.6 24.9 20.0 18.6

3 14.5 14.0 21.4 16.4 15.1

4 12.0 11.5 18.9 13.9 12.6

5 10.0 9.6 16.9 12.0 10.7

6 8.4 8.0 15.3 10.4 9.1

Power output for multiple

received channels

(Downlinklink) dBm

No. Tones 700

MHz Band12/17 700MHz Band13 800MHz 2100MHz 1900MHz

2 9.50 7.60 10.00 11.70 9.10

3 6.00 4.10 6.50 8.20 5.60

4 3.50 1.60 4.00 5.70 3.10

5 1.60 -0.40 2.00 3.80 1.10

6 0.00 -1.90 0.40 2.20 -0.40

Noise Figure 5 dB nominal

Isolation > 90 dB

Power Requirements

110-240 V AC, 50-60 Hz, 20 W

The term “IC” before the radio certification number only signifies that Industry Canada technical specifications were met.

Each Signal Booster is individually tested and factory set to ensure FCC compliance. The Signal Booster cannot be adjusted without factory reprogramming

or disabling the hardware. The Signal Booster will amplify, but not alter incoming and outgoing signals in order to increase coverage of authorized frequency

bands only. If the Signal Booster is not in use for five minutes, it will reduce gain until a signal is detected. If a detected signal is too high in a frequency band,

or if the Signal Booster detects an oscillation, the Signal Booster will automatically turn the power off on that band. For a detected oscillation the Signal Booster

will automatically resume normal operation after a minimum of 1 minute. After 5 (five) such automatic restarts, any problematic bands are permanently shut off

until the Signal Booster has been manually restarted by momentarily removing power from the Signal Booster. Noise power, gain, and linearity are maintained

by the Signal Booster’s microprocessor.

The Manufacturer’s rated output power of this equipment is for single carrier operation. For situations when multiple carrier signals are present, the rating would

have to be reduced by 3.5 dB, especially where the output signal is re-radiated and can cause interference to adjacent band users. This power reduction is to

be by means of input power or gain reduction and not by an attenuator at the output of the device.

3301 East Deseret Drive, St. George, UT

www.wilsonelectronics.com

tech@wilsonelectronics.com

Wilson Electronics products covered by U.S. patent(s) and pending application(s)

For patents go to: weboost.com/us/patents

La page est en cours de chargement...