ASROCK X38TURBOTWINS Le manuel du propriétaire

11

1

ASRock X38TurboTwins-WiFi / X38TurboTwins Motherboard

EnglishEnglish

English

Copyright Notice:Copyright Notice:

Copyright Notice:

No part of this installation guide may be reproduced, transcribed, transmitted, or trans-

lated in any language, in any form or by any means, except duplication of documen-

tation by the purchaser for backup purpose, without written consent of ASRock Inc.

Products and corporate names appearing in this guide may or may not be registered

trademarks or copyrights of their respective companies, and are used only for identifica-

tion or explanation and to the owners’ benefit, without intent to infringe.

Disclaimer:Disclaimer:

Disclaimer:

Specifications and information contained in this guide are furnished for informational

use only and subject to change without notice, and should not be constructed as a

commitment by ASRock. ASRock assumes no responsibility for any errors or omissions

that may appear in this guide.

With respect to the contents of this guide, ASRock does not provide warranty of any kind,

either expressed or implied, including but not limited to the implied warranties or

conditions of merchantability or fitness for a particular purpose. In no event shall

ASRock, its directors, officers, employees, or agents be liable for any indirect, special,

incidental, or consequential damages (including damages for loss of profits, loss of

business, loss of data, interruption of business and the like), even if ASRock has been

advised of the possibility of such damages arising from any defect or error in the guide

or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

CALIFORNIA, USA ONLY

The Lithium battery adopted on this motherboard contains Perchlorate, a toxic

substance controlled in Perchlorate Best Management Practices (BMP) regulations

passed by the California Legislature. When you discard the Lithium battery in

California, USA, please follow the related regulations in advance.

“Perchlorate Material-special handling may apply, see

www.dtsc.ca.gov/hazardouswaste/perchlorate”

ASRock Website: http://www.asrock.com

Published June 2008

22

2

ASRock X38TurboTwins-WiFi / X38TurboTwins Motherboard

EnglishEnglish

English

Motherboard LMotherboard L

Motherboard L

ayoutayout

ayout

1 PS2_USB_PWR1 Jumper 21 USB 2.0 Header (USB6_7, Blue)

2 ATX 12V Connector (ATX12V1) 22 USB 2.0 Header (USB8_9, Blue)

3 eSATAII Connector (eSATAII_BOTTOM) 23 SATAII Connector

4 775-Pin CPU Socket (SATAII_5 (Port4), Orange)

5 North Bridge Controller 24 Front Panel IEEE 1394 Header

6 CPU Fan Connector (CPU_FAN1) (FRONT_1394)

7 2 x 240-pin DDR2 DIMM Slots 25 DeskExpress Hot Plug Detection Header

(Dual Channel A: DDRII_1, DDRII_2; Yellow) (IR1)

8 2 x 240-pin DDR3 DIMM Slots 26 SPI BIOS Chip

(Dual Channel B: DDR3_A1, DDR3_B1; Green) 27 Floppy Connector (FLOPPY1)

9 2 x 240-pin DDR3 DIMM Slots 28 COM Port Header (COM1)

(Dual Channel C: DDR3_A2, DDR3_B2; Pink) 29 WiFi Header (WiFi)

10 IDE1 Connector (IDE1, Blue) 30 Front Panel Audio Header (HD_AUDIO1)

11 South Bridge Controller 31 Internal Audio Connector: CD1 (Black)

12 SATAII Connector (SATAII_1 (Port0), Red) 32 HDMI_SPDIF Header (HDMI_SPDIF1)

13 Clear CMOS Jumper (CLRCMOS1) 33 PCI Slots (PCI1 - 3)

14 Chassis Fan Connector (CHA_FAN1) 34 PCI Express 2.0 x16 Slot (PCIE3, Green)

15 SATAII Connector (SATAII_2 (Port1), Red) 35 PCI Express 2.0 x16 Slot (PCIE2, Green)

16 Chassis Speaker Header (SPEAKER 1) 36 PCI Express x1 Slot (PCIE1)

17 System Panel Header (PANEL1) 37 ATX Power Connector (ATXPWR1)

18 SATAII Connector (SATAII_3 (Port2), Red) 38 FSB1 / FSB2 / FSB3 Jumpers

19 SATAII Connector (SATAII_4 (Port3), Red) 39 eSATAII Connector (eSATAII_TOP)

20 SATAII Connector (SATAII_6 (Port5), Orange)

33

3

ASRock X38TurboTwins-WiFi / X38TurboTwins Motherboard

EnglishEnglish

English

ASRock 1394_SPDIF I/O PlusASRock 1394_SPDIF I/O Plus

ASRock 1394_SPDIF I/O Plus

To enable Multi-Streaming function, you need to connect a front panel audio cable to the front

panel audio header. After restarting your computer, you will find “Mixer” tool on your system.

Please select “Mixer ToolBox” , click “Enable playback multi-streaming”, and click

“ok”. Choose “2CH”, “4CH”, “6CH”, or “8CH” and then you are allowed to select “Realtek HDA

Primary output” to use Rear Speaker, Central/Bass, and Front Speaker, or select “Realtek

HDA Audio 2nd output” to use front panel audio.

** If you use 2-channel speaker, please connect the speaker’s plug into “Front Speaker Jack”.

See the table below for connection details in accordance with the type of speaker you use.

TABLE for Audio Output Connection

Audio Output ChannelsFront Speaker Rear Speaker Central / Bass Side Speaker

(No. 9) (No. 6) (No. 7) (No. 5)

2 V -- -- --

4 V -- -- V

6V--VV

8 VVVV

LAN Port

ACT/LINK

LED

SPEED

LED

1 PS/2 Mouse Port (Green) 10 Microphone (Pink)

2 Coaxial SPDIF Out Port 11 USB 2.0 Ports (USB45)

3 IEEE 1394 Port 12 USB 2.0 Ports (USB23)

* 4 LAN RJ-45 Port 13 USB 2.0 Ports (USB01)

5 Side Speaker (Gray) 14 eSATAII Port (ESATAII_TOP)

6 Rear Speaker (Black) 15 eSATAII Port (ESATAII_BOTTOM)

7 Central / Bass (Orange) 16 Optical SPDIF Out Port

8 Line In (Light Blue) 17 PS/2 Keyboard Port (Purple)

** 9 Front Speaker (Lime)

* There are two LED next to the LAN port. Please refer to the table below for the LAN port LED

indications.

LAN Port LED Indications

SPEED LED Activity/Link LED

Status Description Status Description

Off 10Mbps connection Off No link

Orange 100Mbps connection Orange Linked

Green 1Gbps connection Blinking Data Activity

44

4

ASRock X38TurboTwins-WiFi / X38TurboTwins Motherboard

EnglishEnglish

English

ASRock WiFi-802.11g Module SpecificationsASRock WiFi-802.11g Module Specifications

ASRock WiFi-802.11g Module Specifications

(F(F

(F

or X38Tor X38T

or X38T

urboTurboT

urboT

winswins

wins

--

-

WW

W

iFiF

iF

i Only)i Only)

i Only)

ASRock WiFi-802.11g module is an easy-to-use wireless local area network (WLAN)

adapter to support WiFi+AP function. With ASRock WiFi-802.11g module, you can

easily create a wireless environment and enjoy the convenience of wireless network

connectivity. Therefore, from anywhere within the signal range, you will be able to play

LAN games, connect to the internet, access and share printers, and make Internet

phone calls easily.

Standard - IEEE 802.11g

Data Rate - 6, 9, 12, 18, 24, 36, 48, 54Mbps

Security - Access Point mode (AP mode): WEP, WPA

Network - Access Point mode (AP mode)

Architecture Types - Station mode: Infrastructure mode and Ad-Hoc mode

Frequency Band - 2.4~2.5GHz

Operating Range - Indoor: 80ft (30m)

Outdoor: 200ft (60m)

* The range varies in different environments

Number of - up to 16 stations

Connected Devices

(AP Mode)

Antenna - ASRock WiFi-802.11g omni-directional antenna

LED - Green data transmission (AIR) LED

Support OS - Windows

®

XP / XP 64-bit / Vista

TM

/ Vista

TM

64-bit

Compatibility - Full compatible with IEEE 802.11g standard products

Software Support - ASRock WiFi-802.11g Wizard

If you want to start to use ASRock WiFi-802.11g module on this motherboard, please

carefully read “ASRock WiFi-802.11g Module Operation Guide” in the package for

the detailed introduction and operation procedures. You can also read the document in

the following path of ASRock motherboard support CD:

..\ ASRock WiFi-802.11g \ Vista64_Vista_XP64_XP

55

5

ASRock X38TurboTwins-WiFi / X38TurboTwins Motherboard

EnglishEnglish

English

1. Introduction1. Introduction

1. Introduction

Thank you for purchasing ASRock X38TurboTwins-WiFi / X38TurboTwins motherboard,

a reliable motherboard produced under ASRock’s consistently stringent quality control.

It delivers excellent performance with robust design conforming to ASRock’s commit-

ment to quality and endurance.

This Quick Installation Guide contains introduction of the motherboard and step-by-

step installation guide. More detailed information of the motherboard can be found in

the user manual presented in the Support CD.

Because the motherboard specifications and the BIOS software might be

updated, the content of this manual will be subject to change without

notice. In case any modifications of this manual occur, the updated

version will be available on ASRock website without further notice. You

may find the latest VGA cards and CPU support lists on ASRock website

as well. ASRock website http://www.asrock.com

If you require technical support related to this motherboard, please visit

our website for specific information about the model you are using.

www.asrock.com/support/index.asp

1.1 P1.1 P

1.1 P

ackack

ack

age Contentsage Contents

age Contents

ASRock X38TurboTwins-WiFi / X38TurboTwins Motherboard

(ATX Form Factor: 12.0-in x 9.6-in, 30.5 cm x 24.4 cm)

ASRock X38TurboTwins-WiFi / X38TurboTwins Quick Installation Guide

ASRock X38TurboTwins-WiFi / X38TurboTwins Support CD

ASRock WiFi-802.11g Module Operation Guide (For X38TurboTwins-WiFi Only)

Motherboard Accessories

One 80-conductor Ultra ATA 66/100/133 IDE Ribbon Cable

One Ribbon Cable for a 3.5-in Floppy Drive

Four Serial ATA (SATA) Data Cables (Optional)

One Serial ATA (SATA) HDD Power Cable (Optional)

One HDMI_SPDIF Cable (Optional)

One “ASRock 1394_SPDIF I/O Plus” I/O Panel Shield

WiFi Accessories (For X38TurboTwins-WiFi Only)

One ASRock WiFi-802.11g Module

One Antenna

One WiFi Bracket

66

6

ASRock X38TurboTwins-WiFi / X38TurboTwins Motherboard

EnglishEnglish

English

1.21.2

1.2

SpecificationsSpecifications

Specifications

Platform - ATX Form Factor: 12.0-in x 9.6-in, 30.5 cm x 24.4 cm

- All Solid Capacitor design

CPU - LGA 775 for Intel

®

Core

TM

2 Extreme / Core

TM

2 Quad / Core

TM

2 Duo / Pentium

®

Dual Core / Celeron

®

, supporting Penryn Quad

Core Yorkfield and Dual Core Wolfdale processors

- Compatible with all FSB1600/1333/1066/800MHz CPUs

(see CAUTION 1)

- Supports Hyper-Threading Technology (see CAUTION 2)

- Supports Untied Overclocking Technology (see CAUTION 3)

- Supports EM64T CPU

Chipset - Northbridge: Intel

®

X38

- Southbridge: Intel

®

ICH9R

Memory - Dual Channel DDR3/DDR2 Memory Technology

(see CAUTION 4)

- 4 x DDR3 DIMM slots

- Support DDR3 1600/1333/1066/800 non-ECC, un-buffered

memory (see CAUTION 5)

- Max. capacity of system memory: 8GB (see CAUTION 6)

- 2 x DDR2 DIMM slots

- Support DDR2 1066/800/667 non-ECC, un-buffered memory

(see CAUTION 5)

- Max. capacity of system memory: 4GB (see CAUTION 6)

Expansion Slot - Supports ATI

TM

CrossFire

TM

- 2 x PCI Express 2.0 x16 slots (green @ x16 mode)

- 1 x PCI Express x1 slot

- 3 x PCI slots

Audio - 7.1 CH Windows

®

Vista

TM

Premium Level HD Audio with

Content Protection

- DAC with 110dB dynamic range (ALC890 Audio Codec)

- DTS (Digital Theater Systems) support

(For X38TurboTwins-WiFi Only) (see CAUTION 7)

LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s

- Realtek RTL8111C

- Supports Wake-On-LAN

Wireless LAN - ASRock WiFi-802.11g module

(For X38TurboTwins - 54Mbps IEEE 802.11g / 11Mbps IEEE 802.11b

-WiFi Only) - Supports Software Access Point mode (AP mode) and

Station mode (Infrastructure mode and Ad-hoc mode)

77

7

ASRock X38TurboTwins-WiFi / X38TurboTwins Motherboard

EnglishEnglish

English

Rear Panel I/O ASRock 1394_SPDIF I/O Plus

- 1 x PS/2 Mouse Port

- 1 x PS/2 Keyboard Port

- 1 x Coaxial SPDIF Out Port

- 1 x Optical SPDIF Out Port

- 6 x Ready-to-Use USB 2.0 Ports

- 2 x eSATAII Ports

- 1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED LED)

- 1 x IEEE 1394 Port

- HD Audio Jack: Side Speaker/Rear Speaker/Central/Bass/

Line in/Front Speaker/Microphone (see CAUTION 8)

Connector - 6 x SATAII 3.0Gb/s connectors, support RAID (RAID 0,

RAID 1, RAID 10, RAID 5 and Intel Matrix Storage), NCQ,

AHCI and “Hot Plug” functions (see CAUTION 9)

- 2 x eSATAII 3.0Gb/s connectors (shared with 2 SATAII

connectors) (see CAUTION 10)

- 1 x ATA133 IDE connector (supports 2 x IDE devices)

- 1 x Floppy connector

- 1 x DeskExpress Hot Plug Detection header

- 1 x COM port header

- 1 x HDMI_SPDIF header

- 1 x IEEE 1394 header

- CPU/Chassis FAN connector

- 24 pin ATX power connector

- 8 pin 12V power connector

- CD in header

- Front panel audio connector

- 2 x USB 2.0 headers (support 4 USB 2.0 ports)

(see CAUTION 11)

- 1 x WiFi header (see CAUTION 12)

BIOS Feature - 8Mb AMI BIOS

- AMI Legal BIOS

- Supports “Plug and Play”

- ACPI 1.1 Compliance Wake Up Events

- Supports jumperfree

- AMBIOS 2.3.1 Support

- CPU, DRAM, NB, SB, VTT Voltage Multi-adjustment

- Supports I. O. T. (Intelligent Overclocking Technology)

Support CD - Drivers, Utilities, AntiVirus Software (Trial Version)

Unique Feature - ASRock OC Tuner (see CAUTION 13)

- Hybrid Booster:

- CPU Frequency Stepless Control (see CAUTION 14)

88

8

ASRock X38TurboTwins-WiFi / X38TurboTwins Motherboard

EnglishEnglish

English

CAUTION!

1. FSB1600-CPU will operate in overclocking mode. Besides, if you want to

change a new CPU on this motherboard, please remove the AC power cord

from your PC in advance. This motherboard supports native FSB1333/

1066/800 MHz. For normal operation, you do no need to adjust the jumper

settings. For special overclocking mode, please refer to page 18 and 19

for proper jumper settings.

2. About the setting of “Hyper Threading Technology”, please check page 56

of “User Manual” in the support CD.

3. This motherboard supports Untied Overclocking Technology. Please read

“Untied Overclocking Technology” on page 32 for details.

4. This motherboard supports Dual Channel Memory Technology. Before

you implement Dual Channel Memory Technology, make sure to read

the installation guide of memory modules on page 14 for proper

installation.

5. Please check the table below for the CPU FSB frequency and its

corresponding memory support frequency.

CPU FSB Frequency Memory Support Frequency

1600 DDR2 800, DDR2 1066,

DDR3 800, DDR3 1066, DDR3 1600

1333 DDR2 667, DDR2 800, DDR2 1066,

DDR3 800, DDR3 1066, DDR3 1333

1066 DDR2 667, DDR2 800, DDR2 1066,

DDR3 800, DDR3 1066

800 DDR2 667, DDR2 800,

DDR3 800

WARNING

Please realize that there is a certain risk involved with overclocking, including

adjusting the setting in the BIOS, applying Untied Overclocking Technology, or using

the third-party overclocking tools. Overclocking may affect your system stability, or

even cause damage to the components and devices of your system. It should be

done at your own risk and expense. We are not responsible for possible damage

caused by overclocking.

- ASRock U-COP (see CAUTION 15)

- Boot Failure Guard (B.F.G.)

Hardware - CPU Temperature Sensing

Monitor - Chassis Temperature Sensing

- CPU Fan Tachometer

- Chassis Fan Tachometer

- CPU Quiet Fan

- Voltage Monitoring: +12V, +5V, +3.3V, CPU Vcore

OS - Microsoft

®

Windows

®

2000 / XP / XP 64-bit / Vista

TM

/

Vista

TM

64-bit compliant (see CAUTION 16)

Certifications - FCC, CE, WHQL

* For detailed product information, please visit our website: http://www.asrock.com

99

9

ASRock X38TurboTwins-WiFi / X38TurboTwins Motherboard

EnglishEnglish

English

* DDR2 1066 / DDR3 1600 memory modules will operate in overclocking

mode.

* When you use a FSB1600-CPU on this motherboard, it will run at

DDR2 960 if you adopt a DDR2 1066 memory module. When you

use a FSB1333-CPU on this motherboard, it will run at DDR2 1000

if you adopt a DDR2 1066 memory module.

* If you adopt a DDR2 1066 memory module on this motherboard,

you need to adjust the jumpers. Please refer to page 19 for proper

jumper settings.

6. Due to the operating system limitation, the actual memory size may be

less than 4GB for the reservation for system usage under Windows

®

XP

and Windows

®

Vista

TM

. For Windows

®

XP 64-bit and Windows

®

Vista

TM

64-bit with 64-bit CPU, there is no such limitation.

7. DTS (Digital Theater Systems) is a multi-channel digital surround sound

format. To enable DTS function, you need to adjust the settings after

audio driver installation. Please refer to “DTS Operation Guide” on page 30

for details.

8. For microphone input, this motherboard supports both stereo and mono

modes. For audio output, this motherboard supports 2-channel, 4-

channel, 6-channel, and 8-channel modes. Please check the table on

page 3 for proper connection.

9. Before installing SATAII hard disk to SATAII connector, please read the

“SATAII Hard Disk Setup Guide” on page 38 of “User Manual” in the support

CD to adjust your SATAII hard disk drive to SATAII mode. You can also

connect SATA hard disk to SATAII connector directly.

10. This motherboard supports eSATAII interface, the external SATAII

specification. Please read “eSATAII Interface Introduction” on page 25 for

details about eSATAII and eSATAII installation procedures.

11. Power Management for USB 2.0 works fine under Microsoft

®

Windows

®

Vista

TM

64-bit / Vista

TM

/ XP 64-bit / XP SP1 or SP2 / 2000 SP4.

12. WiFi header supports WiFi+AP function with ASRock WiFi-802.11g or

WiFi-802.11n module, an easy-to-use wireless local area network

(WLAN) adapter. It allows you to create a wireless environment and

enjoy the convenience of wireless network connectivity. Please visit our

website for the availability of ASRock WiFi-802.11g or WiFi-802.11n

module. ASRock website http://www.asrock.com

13. It is a user-friendly ASRock overclocking tool which allows you to surveil

your system by hardware monitor function and overclock your hardware

devices to get the best system performance under Windows

®

environment. Please visit our website for the operation procedures of

ASRock OC Tuner. ASRock website: http://www.asrock.com

14. Although this motherboard offers stepless control, it is not recom-

mended to perform over-clocking. Frequencies other than the recom-

mended CPU bus frequencies may cause the instability of the system

or damage the CPU.

1010

10

ASRock X38TurboTwins-WiFi / X38TurboTwins Motherboard

EnglishEnglish

English

1.31.3

1.3

Minimum Hardware RMinimum Hardware R

Minimum Hardware R

equirement Tequirement T

equirement T

able forable for

able for

WindowsWindows

Windows

® ®

®

VistaVista

Vista

TMTM

TM

Premium 2008 and Basic Logo Premium 2008 and Basic Logo

Premium 2008 and Basic Logo

For system integrators and users who purchase this motherboard and

plan to submit Windows

®

Vista

TM

Premium 2008 and Basic logo, please

follow below table for minimum hardware requirements.

CPU Celeron 420

Memory 1GB system memory (Premium)

512MB Single Channel (Basic)

VGA DX10 with WDDM Driver

with 128bit VGA memory (Premium)

with 64bit VGA memory (Basic)

* After June 1, 2008, all Windows

®

Vista

TM

systems are required to meet above

minimum hardware requirements in order to qualify for Windows

®

Vista

TM

Premium 2008 logo.

15. While CPU overheat is detected, the system will automatically shutdown.

Before you resume the system, please check if the CPU fan on the

motherboard functions properly and unplug the power cord, then plug it

back again. To improve heat dissipation, remember to spray thermal

grease between the CPU and the heatsink when you install the PC

system.

16. ASRock WiFi-802.11g module and RAID / AHCI functions are not

supported under Windows

®

2000 OS. It is recommended to use IDE

mode under Windows

®

2000. Please refer to page 61 of “User Manual” in

the support CD for detailed setup.

1111

11

ASRock X38TurboTwins-WiFi / X38TurboTwins Motherboard

2.2.

2.

InstallationInstallation

Installation

Pre-installation PrecautionsPre-installation Precautions

Pre-installation Precautions

Take note of the following precautions before you install mother-

board components or change any motherboard settings.

1. Unplug the power cord from the wall socket before touching any

component. Failure to do so may cause severe damage to the

motherboard, peripherals, and/or components.

2. To avoid damaging the motherboard components due to static

electricity, NEVER place your motherboard directly on the carpet

or the like. Also remember to use a grounded wrist strap or touch

a safety grounded object before you handle components.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a grounded

antstatic pad or in the bag that comes with the component.

5. When placing screws into the screw holes to secure the

motherboard to the chassis, please do not over-tighten the

screws! Doing so may damage the motherboard.

2.12.1

2.1

CPU InstallationCPU Installation

CPU Installation

For the installation of Intel 775-LAND CPU,

please follow the steps below.

Before you insert the 775-LAND CPU into the socket, please check if

the CPU surface is unclean or if there is any bent pin on the socket.

Do not force to insert the CPU into the socket if above situation is

found. Otherwise, the CPU will be seriously damaged.

775-Pin Socket Overview

EnglishEnglish

English

1212

12

ASRock X38TurboTwins-WiFi / X38TurboTwins Motherboard

EnglishEnglish

English

Step 1. Open the socket:

Step 1-1. Disengaging the lever by depressing

down and out on the hook to clear

retention tab.

Step 1-2. Rotate the load lever to fully open po-

sition at approximately 135 degrees.

Step 1-3. Rotate the load plate to fully open po-

sition at approximately 100 degrees.

Step 2. Insert the 775-LAND CPU:

Step 2-1. Hold the CPU by the edges where are

marked with black lines.

Step 2-2. Orient the CPU with IHS (Integrated

Heat Sink) up. Locate Pin1 and the two

orientation key notches.

For proper inserting, please ensure to match the two orientation key

notches of the CPU with the two alignment keys of the socket.

Step 2-3. Carefully place the CPU into the socket

by using a purely vertical motion.

Step 2-4. Verify that the CPU is within the socket

and properly mated to the orient keys.

Step 3. Remove PnP Cap (Pick and Place Cap):

Use your left hand index finger and thumb to

support the load plate edge, engage PnP cap

with right hand thumb and peel the cap from the

socket while pressing on center of PnP cap to

assist in removal.

black line

775-Pin Socket

Pin1

alignment key

Pin1

orientation

key notch

orientation

key notch

775-LAND CPU

1313

13

ASRock X38TurboTwins-WiFi / X38TurboTwins Motherboard

1. It is recommended to use the cap tab to handle and avoid kicking

off the PnP cap.

2. This cap must be placed if returning the motherboard for after

service.

Step 4. Close the socket:

Step 4-1. Rotate the load plate onto the IHS.

Step 4-2. While pressing down lightly on load

plate, engage the load lever.

Step 4-3. Secure load lever with load plate tab

under retention tab of load lever.

2.22.2

2.2

Installation of CPU Fan and HeatsinkInstallation of CPU Fan and Heatsink

Installation of CPU Fan and Heatsink

For proper installation, please kindly refer to the instruction manuals of your CPU fan

and heatsink.

Below is an example to illustrate the installation of the heatsink for 775-LAND CPU.

Step 1. Apply thermal interface material onto center

of IHS on the socket surface.

Step 2. Place the heatsink onto the socket. Ensure

fan cables are oriented on side closest to the

CPU fan connector on the motherboard

(CPU_FAN1, see page 2, No. 6).

Step 3. Align fasteners with the motherboard

throughholes.

Step 4. Rotate the fastener clockwise, then press

down on fastener caps with thumb to install

and lock. Repeat with remaining fasteners.

If you press down the fasteners without rotating them clockwise,

the heatsink cannot be secured on the motherboard.

Step 5. Connect fan header with the CPU fan

connector on the motherboard.

Step 6. Secure excess cable with tie-wrap to ensure

cable does not interfere with fan operation or

contact other components.

EnglishEnglish

English

1414

14

ASRock X38TurboTwins-WiFi / X38TurboTwins Motherboard

EnglishEnglish

English

1. If you want to install two memory modules, for optimal compatibil-

ity and reliability, it is recommended to install them in the slots of

the same color. In other words, install them in the set of yellow

slots (DDRII_1 and DDRII_2), in the set of green slots (DDR3_A1

and DDR3_B1), or in the set of pink slots (DDR3_A2 and

DDR3_B2).

2. If only one memory module or three memory modules are in-

stalled in DDR3 DIMM slots on this motherboard, it is unable to

activate the Dual Channel Memory Technology. If only one memory

module is installed in DDR2 DIMM slots on this motherboard, it is

unable to activate the Dual Channel Memory Technology.

2.3 Installation of Memor2.3 Installation of Memor

2.3 Installation of Memor

y Modules (DIMM)y Modules (DIMM)

y Modules (DIMM)

This motherboard provides two 240-pin DDR2 (Double Data Rate 2) DIMM slots and

four 240-pin DDR3 (Double Data Rate 3) DIMM slots, and supports Dual Channel

Memory Technology. For dual channel configuration, you always need to install

identical (the same brand, speed, size and chip-type) DDR2/DDR3 DIMM pair in

the slots of the same color. In other words, you have to install identical DDR2

DIMM pair in Dual Channel A (DDRII_1 and DDRII_2; Yellow slots; see p.2 No.7),

identical DDR3 DIMM pair in Dual Channel B (DDR3_A1 and DDR3_B1; Green

slots; see p.2 No.8), or identical DDR3 DIMM pair in Dual Channel C (DDR3_A2

and DDR3_B2; Pink slots; see p.2 No.9), so that Dual Channel Memory Technology

can be activated. This motherboard also allows you to install four DDR3 DIMMs for

dual channel configuration, and please install identical DDR3 DIMMs in all four

slots. You may refer to the Dual Channel Memory Configuration Table below.

DDR3_A1 DDR3_A2 DDR3_B1 DDR3_B2

(Green Slot) (Pink Slot) (Green Slot) (Pink Slot)

2 memory modules SS X SS X

2 memory modules DS X DS X

2 memory modules X SS X SS

2 memory modules X DS X DS

4 memory modules SS SS SS SS

4 memory modules DS DS DS DS

Dual Channel DDR3 Memory Configurations

(DS: Double Side, SS: Single Side)

DDRII_1 DDRII_2

(Yellow Slot) (Yellow Slot)

2 memory modules SS SS

2 memory modules DS DS

Dual Channel DDR2 Memory Configurations

(DS: Double Side, SS: Single Side)

1515

15

ASRock X38TurboTwins-WiFi / X38TurboTwins Motherboard

EnglishEnglish

English

3. If a pair of memory modules is NOT installed in the same Dual

Channel, for example, installing a pair of memory modules in

DDR3_A1 and DDR3_B2, it is unable to activate the Dual Channel

Memory Technology.

4. It is not allowed to install a DDR3 memory module into DDR2 slot

or install a DDR2 memory module into DDR3 slot; otherwise, this

motherboard and DIMM may be damaged.

5. DDR2 and DDR3 memory modules cannot be installed on this

motherboard at the same time.

6. To have the best performance with DDR3 1600 XMP memory

modules, it is suggested to install one memory module on each

channel. For example, install them in the set of green slots

(DDR3_A1 and DDR3_B1) or in the set of pink slots (DDR3_A2

and DDR3_B2).

Installing a DIMMInstalling a DIMM

Installing a DIMM

Please make sure to disconnect power supply before adding or

removing DIMMs or the system components.

Step 1. Unlock a DIMM slot by pressing the retaining clips outward.

Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the break

on the slot.

The DIMM only fits in one correct orientation. It will cause permanent

damage to the motherboard and the DIMM if you force the DIMM into the slot

at incorrect orientation.

Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends fully

snap back in place and the DIMM is properly seated.

1616

16

ASRock X38TurboTwins-WiFi / X38TurboTwins Motherboard

EnglishEnglish

English

2.4 Expansion Slots (PCI and PCI Express Slots)2.4 Expansion Slots (PCI and PCI Express Slots)

2.4 Expansion Slots (PCI and PCI Express Slots)

There are 3 PCI slots and 3 PCI Express slots on this motherboard.

PCI slots: PCI slots are used to install expansion cards that have the 32-bit PCI

interface.

PCIE slots: PCIE1 (PCIE x1 slot; White) is used for PCI Express cards with x1 lane

width cards, such as Gigabit LAN card, SATA2 card and ASRock

PCIE_DE card.

PCIE2 / PCIE3 (PCIE x16 slot; Green) is used for PCI Express cards with

x16 lane width graphics cards.

If you want to use ASRock DeskExpress function on this motherboard,

please install ASRock PCIE_DE card on PCIE1 slot.

Installing an expansion cardInstalling an expansion card

Installing an expansion card

Step 1. Before installing the expansion card, please make sure that the power supply

is switched off or the power cord is unplugged. Please read the documentation

of the expansion card and make necessary hardware

settings for the card before you start the installation.

Step 2. Remove the bracket facing the slot that you intend to use. Keep the screws

for later use.

Step 3. Align the card connector with the slot and press firmly until the card is com-

pletely seated on the slot.

Step 4. Fasten the card to the chassis with screws.

2.5 CrossFire2.5 CrossFire

2.5 CrossFire

TMTM

TM

Operation Guide Operation Guide

Operation Guide

This motherboard supports CrossFire

TM

feature. CrossFire

TM

technology offers the most

advantageous means available of combining multiple high performance Graphics

Processing Units (GPU) in a single PC. Combining a range of different operating modes

with intelligent software design and an innovative interconnect mechanism, CrossFire

TM

enables the highest possible level of performance and image quality in any 3D application.

Currently CrossFire

TM

feature is supported with Windows

®

XP with Service Pack 2 and

Vista

TM

OS. Please check AMD website for ATI

TM

CrossFire

TM

driver updates. For the

detailed operation procedures and compatible PCI Express graphics cards, please refer

to page 22 of “User Manual” in the support CD.

2.6 Surround Display Feature2.6 Surround Display Feature

2.6 Surround Display Feature

This motherboard supports Surround Display upgrade. With the external add-on PCI

Express VGA cards, you can easily enjoy the benefits of Surround Display feature. For

the detailed instruction, please refer to the document at the following path in the

Support CD:

..\ Surround Display Information

1717

17

ASRock X38TurboTwins-WiFi / X38TurboTwins Motherboard

2.7 Jumpers Setup2.7 Jumpers Setup

2.7 Jumpers Setup

The illustration shows how jumpers are

setup. When the jumper cap is placed on

pins, the jumper is “Short”. If no jumper cap

is placed on pins, the jumper is “Open”. The

illustration shows a 3-pin jumper whose pin1

and pin2 are “Short” when jumper cap is

placed on these 2 pins.

Jumper Setting Description

PS2_USB_PWR1 Short pin2, pin3 to enable

(see p.2 No. 1) +5VSB (standby) for PS/2

or USB wake up events.

Note: To select +5VSB, it requires 2 Amp and higher standby current provided by

power supply.

Clear CMOS Jumper

(CLRCMOS1)

(see p.2, No. 13)

Note: CLRCMOS1 allows you to clear the data in CMOS. The data in CMOS includes

system setup information such as system password, date, time, and system

setup parameters. To clear and reset the system parameters to default setup,

please turn off the computer and unplug the power cord from the power supply.

After waiting for 15 seconds, use a jumper cap to short pin2 and pin3 on CLRCMOS1

for 5 seconds. However, please do not clear the CMOS right after you update the

BIOS. If you need to clear the CMOS when you just finish updating the BIOS, you

must boot up the system first, and then shut it down before you do the clear-

CMOS action.

Short Open

Clear CMOSDefault

EnglishEnglish

English

1818

18

ASRock X38TurboTwins-WiFi / X38TurboTwins Motherboard

EnglishEnglish

English

FSB1 Jumper

(FSB1, 3-pin jumper, see p.2 No. 38)

FSB2 Jumper

(FSB2, 5-pin jumper, see p.2 No. 38)

FSB3 Jumper

(FSB3, 5-pin jumper, see p.2 No. 38)

When you mount a FSB800 or FSB1066 CPU, and try to overclock to FSB1333 or

FSB1600 (by BIOS setting) you may face the problem, that DRAM frequency will

be overclocked very high. Please use jumper to force NB to be strapped at higher

frequency, so the DRAM can work at lower frequency.

If you want to overclock the CPU you adopt to FSB1066 on this motherboard, you

need to adjust the jumpers. Please short pin4, pin5 for FSB2 jumper and pin4, pin5 for

FSB3 jumper. Otherwise, the CPU may not work properly on this motherboard.

Please refer to below jumper settings.

If you want to overclock the CPU you adopt to FSB1333 on this motherboard, you

need to adjust the jumpers. Please short pin3, pin4 for FSB2 jumper and pin4, pin5 for

FSB3 jumper. Otherwise, the CPU may not work properly on this motherboard.

Please refer to below jumper settings.

If you want to overclock the CPU you adopt to FSB1600 on this motherboard, you

need to adjust the jumpers. Please short pin3, pin4 for FSB2 jumper and pin3, pin4

for FSB3 jumper. Otherwise, the CPU may not work properly on this motherboard.

Please refer to below jumper settings.

Default

1919

19

ASRock X38TurboTwins-WiFi / X38TurboTwins Motherboard

EnglishEnglish

English

If you use a FSB1600-CPU and adopt a DDR2 1066 memory module on this

motherboard, you need to adjust the jumpers. Please short pin4, pin5 for FSB3.

Otherwise, the CPU and memory module may not work properly on this motherboard.

Please refer to below jumper settings.

If you use a FSB1333-CPU and adopt a DDR2 1066 memory module on this

motherboard, you need to adjust the jumpers. Please short pin4, pin5 for FSB2.

Otherwise, the CPU and memory module may not work properly on this motherboard.

Please refer to below jumper settings.

If you use a FSB1066-CPU and adopt a DDR2 1066 memory module on this

motherboard, you need to adjust the jumpers. Please short pin2, pin3 for FSB3.

Otherwise, the CPU and memory module may not work properly on this motherboard.

Please refer to below jumper settings.

FSB1600 / DDR2 1066

FSB1333 / DDR2 1066

FSB1066 / DDR2 1066

2020

20

ASRock X38TurboTwins-WiFi / X38TurboTwins Motherboard

EnglishEnglish

English

the red-striped side to

Pin1

2.8 Onboard Headers and Connectors2.8 Onboard Headers and Connectors

2.8 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place

jumper caps over these headers and connectors. Placing jumper

caps over the headers and connectors will cause permanent dam-

age of the motherboard!

FDD connector

(33-pin FLOPPY1)

(see p.2 No. 27)

Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the

connector.

Primary IDE connector (Blue)

(39-pin IDE1, see p.2 No. 10)

Note: Please refer to the instruction of your IDE device vendor for the details.

Serial ATAII Connectors These six Serial ATAII (SATAII)

(SATAII_1 (Port0): connectors support SATA data

see p.2, No. 12) cables for internal storage

(SATAII_2 (Port1): devices. The current SATAII

see p.2, No. 15) interface allows up to 3.0 Gb/s

(SATAII_3 (Port2): data transfer rate.

see p.2, No. 18)

(SATAII_4 (Port3):

see p.2, No. 19)

(SATAII_5 (Port4):

see p.2, No. 23)

(SATAII_6 (Port5):

see p.2, No. 20)

SATAII_5 (Port4) and SATAII_6 (Port5) connectors can be used for

internal storage device or be connected to eSATAII connectors to

support eSATAII device. Please read “eSATAII Interface Introduction”

on page 25 for details about eSATAII and eSATAII installation procedures.

connect the black end

to the IDE devices

connect the blue end

to the motherboard

80-conductor ATA 66/100/133 cable

SATAII_5 (Port4) SATAII_1 (Port0)

SATAII_6 (Port5) SATAII_2 (Port1)

SATAII_3 (Port2)

SATAII_4 (Port3)

La page charge ...

ASROCK X38TURBOTWINS Le manuel du propriétaire

Ce manuel convient également à

ASROCK X38TURBOTWINS Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents