Jenn-Air JBRFR36IGX Le manuel du propriétaire

W10918236B



COLUMN REFRIGERATION



RÉFRIGÉRATION COLONNE

INTRODUCTION | 3

INTRODUCTION

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

DANGER

WARNING

You can be killed or seriously injured if you don't immediately follow instructions.

You can be killed or seriously injured if you don't follow instructions.

SAFETY

SAVE THESE INSTRUCTIONS

IMPORTA NT SAFETY INSTRUCTIONS

WARNING:

To reduce the risk of shock, or injury when using your refrigerator, follow these basic precautions:

■ To avoid a hazard due to instability of the

with the instructions.

■ Installation shall be performed only by

manufacturer, or an authorized agent.

■ Plug into a grounded 3 prong outlet.

■ Do not remove ground prong.

■ Do not use an adapter.

■ Do not use an extension cord.

■ Disconnect power to all units before servicing.

■ If the SUPPLY CORD is damaged, it must be

replaced by the manufacturer, its service agent

a hazard.

■ Replace all parts and panels before operating.

■ This appliance is not intended for use by persons

(including children) with reduced physical, sensory

or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision

or instruction concerning use of the appliance by a

person responsible for their safety.

■ Children should be supervised to ensure that they do

not play with the appliance.

■ This refrigerator is intended to be used in household

and similar applications such as:

working environments

–farm houses and by clients in hotels, motels,

and other residential type environments

–bed and breakfast type environments

–catering and similar non-retail applications

■ Remove doors from your old refrigerator.

■ Connect to a potable water supply only.

■ Use

■ Ke mmable materials and vapors, such

as gasoline, away from refrigerator.

■ Do not store explosive substances such as

this refrigerator.

■ Use two or more people to move and install

refrigerator.

■ Disconnect power before installing ice maker

(on ice maker kit ready models only).

■ Use a sturdy glass when dispensing ice

(on some models).

■ Do not hit the refrigerator glass doors

(on some models).

4 | INTRODUCTION

INTRODUCTION

PROPER DISPOSAL OF YOUR OLD

REFRIGERATOR

IMPORTANT: Do your part to prevent accidental

child entrapment and suffocation by properly

disposing of your old refrigerator or freezer.

WARNING

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or

brain damage.

BEFORE YOU THROW AWAY YOUR OLD

REFRIGERATOR OR FREEZER:

 Take off the doors.

 Leave the shelves in place so children may

not easily climb inside.

Important information to know about disposal

of refrigerants:

Dispose of refrigerator in accordance with

Federal and Local regulations. Refrigerants

must be evacuated by a licensed, EPA certied

refrigerant technician in accordance with

established procedures.

INTRODUCTION | 5

INTRODUCTION

REGISTERING YOUR APPLIANCE

Gain access to our concierge-level Customer

Support by registering your appliance.

We make product registration simple and

straightforward so you can start using your

exclusive JennAir beneﬁts today.

Registering your appliance allows you to:

■ Streamline your warranty service

If we have your appliance information, we

can help you faster.

■ Protect your purchase

In case of an insurance loss—such as ﬁre,

ﬂood, or theft—your product registration

could serve as a proof of purchase.

■ Keep your family safe

We’ll notify you in the rare case of a safety

notiﬁcation.

Start taking advantage of these beneﬁts today

by going online to register your appliance at

https://register.jennair.com.

TABLE OF CONTENTS

PRODUCT IDENTIFICATION

Your product identiﬁcation, which includes

the model and serial numbers, is listed on the

product rating plate.

Recording this information below allows us to

assist you more easily if your appliance should

ever require service from one of our JennAir

®

Authorized Service Providers.

Model Number: ______________________________

Serial Number: _______________________________

Date of Installation: _________________________

Authorized Dealer: __________________________

Authorized Dealer Phone #: _________________

INTRODUCTION

Safety ............................................................................. 3

Proper Disposal of

Your Old Refrigerator ......................................... 4

Registering Your Appliance ............................ 5

Product Identiﬁcation ........................................ 5

Product Features .................................................... 6

Refrigerator Controls ........................................... 8

Freezer Controls ...................................................... 10

GETTING STARTED

Before Use ................................................................... 12

Smart Features ........................................................ 12

Smart Grid ................................................................... 13

Automatic Setup (WPS) ..................................... 14

Manual Setup (First-Time Use) ..................... 16

Shelves ........................................................................... 17

Deli/Crisper Drawers ............................................ 17

CARE AND CLEANING

Cleaning ....................................................................... 18

Leather Panel Care ................................................ 18

Vacation Care ............................................................ 19

Power Interruptions ............................................. 19

Replacing The Water Filter...............................20

TROUBLESHOOTING

Operation ..................................................................... 22

Temperature And Moisture ............................. 23

Ice And Water ........................................................... 23

Lights...............................................................................24

ASSISTANCE

Contact .......................................................................... 25

In The U.S.A. ............................................................... 25

In Canada ..................................................................... 25

Accessories ................................................................. 25

Connected Appliance

Regulatory Notices................................................26

Performance Data Sheet..................................28

Warranty.......................................................................30

TABLE DES MATIÈRES.................35

INTRODUCTION

PRODUCT FEATURES

1. Fully Integrated and Flush

Design with Articulating Hinge

Creates an integrated appearance with

custom cabinets without exposed hinges or

trim pieces.

2. Adjustable Aluminum and

Glass Door Bins

Make it easy to customize storage

according to your preferences, providing

quick access to frequently used items.

Refrigerator and freezer door bins can be

positioned to accommodate a variety of

container sizes.

3. Custom Overlay Design

Ships with factory-installed doors. To create

a ﬁnished refrigerator, customers must

purchase either custom overlay panels and

handles from a cabinet manufacturer, or a

JennAir

®

suite-coordinating panel kit.

4. Obsidian Interior

Showcases food items throughout the

refrigerator or freezer, and provides a

sharper contrast than white interiors.

5. 90°/115° Door Stop Position

Provides options to ensure ample clearance

between the open door and adjacent

cabinetry.

6. Wi-Fi Connectivity

This refrigerator can connect with in-home

Wi-Fi to provide remote control through

the JennAir

®

App, available to download for

use with either iOS or Android devices.

INTRODUCTION

6 | INTRODUCTION

14.

13.

12.

11.

9.

8.

10.

7.

1.

2.

3.

4.

5.

6.

INTRODUCTION | 7

INTRODUCTION

7. Soft, Auto-Close Crisper Drawers

Provide smooth operation by rolling open

even when fully loaded, and feature an

innovative auto-close design that pulls the

drawer closed.

8. Electronic Temperature-

Controlled Crisper Drawer

(Refrigerator)

Drawer slides open effortlessly, even when

fully loaded, with soft, self-close glides.

Two temperature presets are available on

the interior control to keep items at the

optimal temperature. You can choose from

following:

 Produce: 39°F (3.9°C)

 Assorted: 37°F (2.8°C)

9. Capacitive Touch Controls with

LED Display

The touch panel houses the control menu

and function controls. The touch keypads

are very sensitive and only require a light

touch. The controls are located in the

midsection of each column for easy access.

10. Electronic Temperature-

Controlled Deli Drawer

(Refrigerator)

Deli slides open effortlessly, even when fully

loaded, with soft, self-close glides.

Five temperature presets are available on

the interior control to keep items at the

optimal temperature. You can choose from

following:

 Produce: 39°F (3.9°C)

 Assorted: 37°F (2.8°C)

 Beverage: 34°F (1°C)

 Deli: 33°F (0.6°C)

 Meat: 32°F (0°C)

Electronic Temperature-

Controlled Deli Drawer (Freezer)

Three temperature presets are available

on the interior control to keep items at the

optimal temperature. You can choose from

following:

 Assorted: 0°F (-17.8°C)

 Spirits: -2°F (-18.9°C)

 DeepFreeze: -8°F (-22.2°C)

11. Water Dispenser (Refrigerator)

Allows you to dispense ﬁltered water.

†®

NSF is a registered trademark of NSF International.

12. Interior Perimeter LED Theater

Lighting

Perimeter LED lighting elegantly ramps up

to full brightness when the door or interior

drawers are opened, increasing visibility

by minimizing shadows caused by top

lighting. Selecting a cooling zone on the

control panel causes the lighting in the

same zone to pulse.

13. Adjustable Clear Glass Shelves

Tint-free, clear glass shelves that offer an

open, reﬁned look that makes food and

beverages easy to see and locate. Glass

shelves complement the LED lighting for

exceptional clarity that allows more light to

ﬁll the interior.

14. EveryDrop

®

Filter

EveryDrop

®

water ﬁlters are NSF

®†

certiﬁed

to reduce most contaminants, including

chlorine taste and odor, lead, pesticides,

and trace amounts of pharmaceuticals.

EveryDrop

®

brand ﬁlters are the only ﬁlters

tested and certiﬁed for your refrigerator

system. Replace your EveryDrop

®

ﬁlter

every 6 months for maximum contaminant

reduction.

15. Automatic Ice Maker (Freezer)

Ensures a continuous supply of fresh ice

cubes made from ﬁltered water.

REFRIGERATOR CONTROLS

1. Viewing and Adjusting

Temperature

When you ﬁrst install your

refrigerator, make sure that

the control is still set to the

recommended setting. The

factory-recommended

temperature is 37°F (3°C).

Touch - or + to select a

temperature seting. Press and hold - and

+ to change display from Fahrenheit to

Celsius.

2. Activate Temperature Mode for

Refrigerator Deli Drawer

Touch Assorted, Beverage,

Deli, Meat, or Produce to

select a zone temperature

setting.

3. Cooling Zones

Select features of your refrigerator are tied

to the perimeter lighting.

Press a zone key to light the

corresponding zone in your

refrigerator.

INTRODUCTION

8 | INTRODUCTION

7. 8.

1. 2. 3.

4.

6.5.

INTRODUCTION | 9

INTRODUCTION

4. Max Cool

The Max Cool feature

assists with periods of high

refrigerator use, full grocery

loads, or temporarily warm

room temperatures. Press MAX COOL to

activate Max Cool. After the Max Cool cycle

completes, the refrigerator will return to its

previous setting.

5. Connect

Wi-Fi connectivity allows your

Smart Refrigerator to connect

to the Internet and interact

with the JennAir

®

App from

your smartphone or mobile device. See the

“Automatic Setup—Wi-Fi Protected Setup

(WPS)” section for more information.

Sabbath

Allows the door of the

refrigerator to be opened or

closed during the Sabbath

or other religious holidays

without activating the interior lights or

controls. Press and hold Sabbath for

3 seconds to activate Sabbath mode.

Lock

The control panel can be

locked for easy cleaning or

to avoid unintentional mode

changes.

6. Power Outage

The Power Outage indicator

lets you know if the power

supply to the refrigerator has

been off and the temperature has risen.

Over temp Alarm

Helps avoid food spoilage

and high energy costs by

sounding an alert when

refrigerator temperatures remain at

unusually high levels.

Door Open

The Door Open alarm feature

sounds an alarm when the

refrigerator door(s) or freezer

door is open for 5 minutes

and cooling is turned on. The alarm will

repeat every 2 minutes. Close the door to

turn the alarm and “Door Open” alert off. To

stop the alarm noise with the door open,

press any key.

7. Showroom

This mode is used when the

refrigerator is on display in a

retail store or if you want to

turn the cooling off and

deactivate all other functions except interior

lighting.

To activate showroom mode, press

and hold top and bottom zone

icons simultaneously for 3 seconds.

To deactivate the showroom mode,

press and hold top and bottom

zone icons simultaneously for

3 seconds.

8. Filter Reset

Displays the status of the

water ﬁlter. To reset the

ﬁlter, press and hold FILTER

RESET for 3 seconds. After

countdown, the “Replace Filter” indicator

will turn off.

Replace Filter

Replace the water ﬁlter.

While you are dispensing

water, the “Replace Filter”

icon will ﬂash constantly

from beginning to the end of dispensing.

After 14 days without replacing the water

ﬁlter, the “Replace Filter” icon will blink

seven times and an alert tone will sound

three times at the end of dispensing. See

the “Water Filtration System” section.

NOTE: “Replace Filter” will remain

illuminated if a ﬁlter reset is not completed.

Order Filter

Order a replacement water

ﬁlter.

10 | INTRODUCTION

INTRODUCTION

FREEZER CONTROLS

1. Pure Freeze

®

Feature

Pure Freeze

®

feature is

activated automatically when

the freezer is at its lowest

setting. The Pure Freeze

®

setting reduces

freezer burn.

Viewing and Adjusting

Temperature

When you ﬁrst install your

freezer, make sure that

the control is still set to the

recommended temperature.

The factory recommended

setting is -2°F (19°C) for the

freezer.

Touch - or + to select a temperature setting.

2. Activate Temperature Mode for

Freezer Deli Drawer

Touch Assorted, Spirits, or

DeepFreeze to select a zone

temperature setting.

3. Cooling Zones

Select features of your freezer are

tied to the perimeter lighting.

Press the zone keys to light the

corresponding zones in your freezer.

7. 8.

1. 2. 3.

4.

6.5.

INTRODUCTION | 11

INTRODUCTION

4. Max Ice

The Max Ice Setting increases

the freezer cooling capacity

improving the ice making

rate.

Ice Maker Off

To turn the ice maker off,

touch ICE MAKER OFF.

5. Connect

Wi-Fi connectivity allows your

Smart Freezer to connect

to the Internet and interact

with the JennAir

®

App from

your smartphone or mobile device. See the

“Automatic Setup—Wi-Fi Protected Setup

(WPS)” section for more information.

Sabbath

Allows the door of the freezer

to be opened or closed

during the Sabbath or other

religious holidays without

activating the interior lights or controls.

Press and hold Sabbath for 3 seconds to

activate Sabbath mode.

Lock

The dispenser can be locked

for easy cleaning or to avoid

unintentional dispensing.

6. Power Outage

The Power Outage indicator

lets you know if the power

supply to the freezer has

been off and the freezer temperature has

risen.

Over temp Alarm

Helps avoid food spoilage

and high energy costs by

sounding an alert when

freezer temperatures remain at unusually

high levels.

Door Open

The Door Open alarm feature

sounds an alarm when the

refrigerator door(s) or freezer

door is open for 5 minutes

and cooling is turned on. The alarm will

repeat every 2 minutes. Close the door to

turn the alarm and “Door Open” alert off. To

stop the alarm noise with the door open,

press any key.

7. Showroom

This mode is used when the

freezer is on display in a retail

store or if you want to turn

the cooling off and

deactivate all other functions except interior

lighting.

To activate showroom mode, press

and hold top and bottom zone icons

simultaneously for 3 seconds.

To deactivate the showroom mode,

press and hold top and bottom zone

icons simultaneously for 3 seconds.

8. Filter Reset

Displays the status of the

water ﬁlter. To reset the

ﬁlter, press and hold FILTER

RESET for 3 seconds. After

countdown, the “Replace Filter” indicator

will turn off.

Replace Filter

Replace the water ﬁlter.

While you are dispensing

water, the “Replace Filter”

icon will ﬂash constantly from

beginning to the end of dispensing. After 14

days without replacing the water ﬁlter, the

“Replace Filter” icon will blink seven times

and an alert tone will sound three times

at the end of dispensing. See the “Water

Filtration System” section.

NOTE: “Replace Filter” will remain

illuminated if a ﬁlter reset is not completed.

Order Filter

Order a replacement water

ﬁlter.

12 | GETTING STARTED

GETTING STARTED

BEFORE USE

Before using your refrigerator, all packaging

materials should be removed and the interior

should be cleaned.

 Remove tape and glue residue from

surfaces before turning on the refrigerator.

With your ﬁngers, rub a small amount of

liquid dish soap over any adhesive and wipe

with warm water to remove.

 Do not use sharp instruments, rubbing

alcohol, ﬂammable ﬂuids, or abrasive

cleaners to remove tape or glue. These can

damage the surfaces of your refrigerator.

 Dispose of and/or recycle all packaging

materials.

 After all packaging materials have

been removed, clean the inside of your

refrigerator.

 Flush 3 gallons (11.4 L) of water through

the water system to clear air from the

water line and to keep the dispenser

from dripping and/or avoiding decreased

dispenser ﬂow.

NOTE: If the ﬁlter is not installed correctly,

water may dispense at a lower ﬂow rate

and there will be slower ice production.

Improper ﬁlter installation may also cause

the water ﬁlter housing to leak.

SMART FEATURES

Smart Features help make your every day a

little more efﬁcient by letting you remotely

monitor, manage, and maintain your

refrigerator.

REMOTE TEMPERATURE CONTROL

What it does: Allows you to control the

temperature of your refrigerator remotely from

your mobile device via the JennAir

®

App.

What it does for you: Lets you control

temperatures in your refrigerator, freezer, and

temp-controlled pantry remotely—not just

when you are standing in front of it.

WATER FILTER STATUS

What it does: Gives you a look at the life

remaining for your air and water ﬁlters before a

replacement is needed.

What it does for you: Helps you be more

efﬁcient in planning for, ordering, and replacing

ﬁlters.

AUTO REORDER

What it does: Allows you to order replacement

ﬁlters, consumables, and accessories via the

JennAir

®

App for delivery directly to your home.

What it does for you: Simpliﬁes ordering

correct water and air ﬁlters—no trips to the

store and searching for the correct ﬁlters.

OVER TEMPERATURE

What it does: Sends you a notiﬁcation when

the temperature in your refrigerator reaches

and rises above a speciﬁed value in the

refrigerator and freezer compartments.

What it does for you: Alerts you to over-

temperature status to provide input regarding

disposition of refrigerator/freezer contents.

MAX COOLREFRIGERATOR

What it does: Allows you to control your

refrigerator remotely from your mobile device

via the JennAir

®

App.

What it does for you: Lets you turn on/off Max

Cool options remotely to make temperatures

colder in the refrigerator in anticipation of

loading newly purchased grocery items.

MAX ICEFREEZER

What it does: Allows you to control your freezer

remotely from your mobile device via the

JennAir

®

App.

What it does for you: Makes fresh-tasting ice to

accommodate your entertainment needs - up

to 4 pounds in 24 hours.

PURE FREEZE

®

MODE

What it does: Allows you to receive status

of your refrigerator remotely to your mobile

device via the JennAir

®

App.

What it does for you: Indicates when

temperatures are adjusted down to a deep

freeze level to reduce freezer burn and helps

frozen items maintain their appearance and

taste.

GETTING STARTED | 13

GETTING STARTED

SMART FEATURES CONT.

SABBATH MODE

What it does: Allows the door of the refrigerator

or freezer to be opened or closed during the

Sabbath or other religious holidays without

activating the interior lights or controls. Allows

you to turn on and off remotely from your

mobile device via the JennAir

®

App.

What it does for you: Lets you turn on/off

Sabbath mode options remotely.

DOOR OPEN ALERT

What it does: Sends you a notiﬁcation when

the door of the appliance has been left open.

What it does for you: Alerts you to door ajar

status so you can close the door(s) or call home

to ask someone else to close the door before an

over-temp situation arises.

POWER OUTAGE

What it does: Sends you a notiﬁcation when

power to your refrigerator goes out, returns, or

highest temperature is reached.

What it does for you: Alerts you to power status

and disposition of the appliance contents.

SMART GRID

This product has WiFi capability and requires

Internet connectivity and a wireless router

to enable interconnection with an Energy

Management System, and/or with other

external devices, systems, or applications.

14 | GETTING STARTED

GETTING STARTED

AUTOMATIC SETUPWIFI

PROTECTED SETUP WPS

YOU WILL NEED:

A home wireless router capable of WPS (Wi-Fi

protected Setup). The router should be on and

have a live internet connection.

To use this feature you need:

 A smartphone running Android 4.3 (or

higher) with a 1280x720 (or higher) screen

or a tablet or a smartphone running iOS 8

(or higher).

 A wireless router 2.4 Ghz Wi-Fi b/g/n

connected to internet (verify with your

smart device that the signal of your home

wireless network is strong close to the

appliance).

 The Smart Appliance Identiﬁcation Number

(SAID) from your refrigerator. This is located

on a sticker on the inside of the water ﬁlter

door.

NOTE: If your home wireless router is not

equipped with a WPS button, please check

the user manual of your router to conﬁrm

if it is WPS capable. If not, alternate setup

instructions are at www.jennair.com/connect.

SAID:

0123456789

Contains FCC ID:

A5UWICHIN01

MAC ID:

88:E7:12:XX:YY:ZZ

Contains IC:

10248A-WICHIN01

1. Set up router

Press the WPS button on the router. An

indicator light will begin blinking.

NOTE: The WPS function on your router is

active for 2 minutes. Complete the next step

within that timeframe, or you will need to

reinitiate WPS.

2. Set up refrigeration appliance

(time-sensitive step)

Press and hold CONNECT on

the control panel for

3 seconds.

The Wi-Fi status indicator ( )

on the appliance control

panel will blink slowly while

your appliance and router

attempt to connect. If the connection is

successful, the Wi-Fi status indicator will

illuminate and remain lit.

IF YOUR APPLIANCE DOESN’T CONNECT:

If your appliance and router fail to connect after

2 minutes, the Wi-Fi status indicator will blink

rapidly for 5 seconds and then turn off. Check

any connection instructions for your speciﬁc

router, and refer to alternate instructions at

www.jennair.com/connect.

NOTE: If this is your ﬁrst smart appliance, you

will need to download the JennAir

®

App and

create an online user account.

If you already have the app and a user account,

please skip ahead to Step 4, “Register your

refrigerator in your user account.”

INTERNET

WI-FI PROTECTED

SETUP (WPS)

HOME WIRELESS

ROUTER

GETTING STARTED | 15

GETTING STARTED

AUTOMATIC SETUPWIFI

PROTECTED SETUP WPS CONT.

DISCONNECT AND RECONNECT WIFI

To disconnect Wi-Fi, press and the hold

CONNECT for 7 to 15 seconds. The Wi-Fi status

indicator will turn off, indicating that you have

disabled Wi-Fi.

To reconnect Wi-Fi, press and hold CONNECT

for 3 seconds on the control panel.

 The Wi-Fi status indicator ( ) on the

appliance control panel will blink slowly

while your appliance and router attempt to

connect.

 If the connection is successful, the Wi-Fi

status indicator will illuminate and remain

lit.

DISCONNECT AND RECONNECT ROUTER

 To disconnect your refrigerator from your

router, press and hold CONNECT for more

than 15 seconds. The Wi-Fi indicator will

turn off, indicating that your refrigerator is

completely disconnected from Wi-Fi and

your router.

 To reconnect your appliance to your router

and reconnect Wi-Fi, press and hold

CONNECT for 3 seconds.

The Wi-Fi status indicator ( ) on the appliance

control panel will blink slowly while your

refrigerator and router attempt to connect.

If the connection is successful, the Wi-Fi status

indicator will come on and remain lit.

Press the WPS button on the router. An

indicator light will begin blinking.

NOTE: The WPS function on your router is

active for 2 minutes. Complete the next step

within that timeframe or you will need to

reinitiate WPS.

3. Download JennAir

®

App and set up user

account

From your mobile device, smartphone, or tablet,

go to www.jennair.com/connect and follow

the instructions to download and install the

JennAir

®

App.

Once installed, tap the JennAir

®

App icon to

open the app. You will be guided through the

steps to set up a user account. The App will

make sure to get the necessary personal and

home information as well as information about

your energy company.

4. Register your refrigerator in your user

account

Registering your refrigerator in your account

is a necessary step in order for you to take

full advantage of the Smart features. When

prompted by the app, enter the SAID (case-

sensitive), which can be found on a sticker on

the inside of the water ﬁlter door.

My Smart Appliance ID# is:

_________________________________________________

The Wi-Fi status indicator on the refrigerator

control panel will blink slowly while your

refrigerator and router attempt to connect.

NOTE: This blinking only applies to ﬁrst-time

registration after provisioning. Blinking will

not occur for automatic reconnection after a

connection is established.

 Once you’ve connected your refrigerator

to your home Wi-Fi network, it will remain

linked even if the power goes out, you

move the appliance, or if you put it in

storage.

 If you replace your wireless router or get a

different Smart appliance, you will need to

repeat this connectivity set-up process.

16 | GETTING STARTED

GETTING STARTED

MANUAL SETUP FIRSTTIME USE

 ACCESS POINT METHOD

This procedure uses Micro Access Point

technology and is applicable if your router does

not support WPS.

1. Before starting the Setup procedure, please

take note of the home wireless network

name (SSID), its password and the SAID of

appliance. These will be required during the

installation process.

2. Turn on your router and make sure the

internet connection is working.

3. On your appliance, activate the provisioning

process using the AP method. You

should see the Wi-Fi icon blinking on the

appliance HMI.

4. Turn on your smart device (phone or tablet)

and access your list of available wireless

networks in the settings menu.

5. The appliance has created a wireless

network (SSID). Select this network from

the list of available wireless networks. The

network name is made up of the preﬁx

from your appliance type (e.g. washer,

dryer, etc.) followed by the MAC address (ex.

REFRID_88_E7_12_B3_66_ C3). If you don’t

see it, you may need to refresh the list of

networks or verify the Wi-Fi icon is on the

appliance display.

6. Once you have selected the SSID, a

password will be required. Use the SAID as

a password (i.e., 444441ABCD).

NOTE: This password is case-sensitive.

7. Connect to the network.

8. Wait until your device is conﬁrmed to be

connected to the appliance Wi-Fi network.

9. Open a web browser. If nothing appears,

type “192.168.10.1” in the address bar (URL)

and press Enter. The browser displays a

Smart web page. It is the conﬁguration

page of the Wi-Fi radio of your appliance.

10. In the drop-down list of available networks,

select the name of your home wireless

network.

11. If your home wireless network is hidden,

select “Other” and manually enter its name

(SSID) and security protocol.

WPA2

12. Enter the password for your home wireless

network, if required, and submit.

Remember, this kind of password is case-

sensitive.

13. Click the “ ” button to submit, and wait a

few seconds.

14. The Wi-Fi icon on the appliance should stop

blinking and turn on permanently once

connected. Otherwise, disconnect and

reconnect the appliance to the main power

and repeat the procedure.

15. The Setup process is complete.

GETTING STARTED | 17

GETTING STARTED

SHELVES

The shelves in your appliance are adjustable to

meet your individual storage needs.

Storing similar food items together in your

appliance and adjusting the shelves to ﬁt

different heights of items will make ﬁnding the

exact item you want easier. It will also reduce

the amount of time the refrigerator door is

open and save energy.

Important information to know about glass

shelves and covers:

Do not clean glass shelves or covers with warm

water when they are cold. Shelves and covers

may break if exposed to sudden temperature

changes or impact, such as bumping.

Tempered glass is designed to shatter into many

small, pebble-sized pieces. This is normal. Glass

shelves and covers are heavy. Use both hands

when removing them to avoid dropping.

DELICRISPER DRAWERS

TO REMOVE AND REPLACE THE DELICRISPER

DRAWERS:

1. To remove the deli/crisper drawers, press

the clips located at the bottom of the

drawer.

2. Lift up on the drawer and pull straight out.

1. To replace the deli/crisper drawers, extend

the glides to their fullest extent.

2. Using your ﬁngers, hold the glides in place

as you place the drawer back on the glides.

TO REMOVE AND REPLACE THE SHELF AND

SHELF SUPPORTS:

1. Remove the shelf by tilting it up at the front

and lifting it out of the shelf supports. Pull

the shelf straight out.

2. To replace the shelf, reposition the shelf

supports in the desired location. Check that

they are level and ﬁrmly inserted in the

support rails.

3. Place the back of the shelf in the shelf

supports.

4. Lower the front of the shelf and make sure

that it is positioned correctly.

18 | CARE AND CLEANING

CARE AND CLEANING

CLEANING

Below are the recommended steps to clean

your appliance.

1. Press the power switch to OFF.

A. To access the power switch, remove the

toe kick by pulling out to release it from

the brackets.

2. Remove all removable parts (such as

shelves and crispers) from the inside of the

appliance.

Explosion Hazard

Failure to do so can result in death,

LEATHER PANEL CARE

Under normal usage conditions, regular

dusting and vacuum cleaning in crevices or

bottoms is all that is necessary to clean the

leather panel.

For minor spots, wipe any excess liquid up

immediately with a clean absorbent cloth or

sponge. If necessary, use a lightly moistened

cloth with clean lukewarm water and let dry

naturally.

NOTE:

 Using hairdryer for drying may damage

leather panel, so do not dry using

hairdryers.

 Do not use saddle soap, cleaning solvents,

furniture polish, oils, varnish, abrasive

cleaners, detergent soaps, or ammonia on

leather panel.

3. Hand wash, rinse, and dry removable

parts and interior surfaces thoroughly. Use

a clean sponge or soft cloth and a mild

detergent in warm water.

 Do not use abrasive or harsh cleaners

such as window sprays, scouring

cleansers, ﬂammable ﬂuids, cleaning

waxes, concentrated detergents,

bleaches, or cleansers containing

petroleum on plastic parts, interior,

door liners, or gaskets. Do not use

paper towels, scouring pads, or other

harsh cleaning tools. These can scratch

or damage materials.

 To help remove odors, you can wash

interior walls with a mixture of warm

water and baking soda (2 tbs to 1 qt

[26 g to 0.95 L] of water).

4. Wash stainless steel and painted metal

exteriors with a clean sponge or soft cloth

and a mild detergent in warm water. Do not

use abrasive or harsh cleaners, or cleaners

containing chlorine. Dry thoroughly with a

soft cloth.

5. Press the power switch to ON.

6. To replace, press the toekick panel onto

the toekick bracket to engage the gripping

pads.

CARE AND CLEANING | 19

CARE AND CLEANING

VACATION CARE

1. Remove all food from the

refrigerator/freezer.

2. Empty the ice bin.

3. Turn the power switch to Off.

A. To access the power switch, remove the

toekick by pulling out to release it from

the brackets.

B. To replace, press the toekick panel onto

the toekick bracket to engage the

gripping pads.

4. Clean refrigerator/freezer, wipe it, and dry

well.

5. Tape rubber or wood blocks to the tops of

both doors to prop them open far enough

for air to get in. This stops odor and mold

from building up.

POWER INTERRUPTIONS

If the power will be out for 24 hours or less,

keep the door closed to help food stay cold and

frozen.

If the power will be out for more than 24 hours,

do one of the following:

 Remove all frozen food and store it in a

frozen food locker.

 Place 2 lbs (907 g) of dry ice in the freezer

for every cubic foot (28 L) of freezer space.

This will keep the food frozen for 2 to 4

days.

 If neither a food locker nor dry ice is

available, consume or can perishable food

at once.

REMEMBER: A full freezer stays cold longer

than a partially ﬁlled one. A freezer full of meat

stays cold longer than a freezer full of baked

goods. If you see that food contains ice crystals,

it may be refrozen, although the quality and

ﬂavor may be affected. If the condition of the

food is poor, dispose of it.

20 | CARE AND CLEANING

CARE AND CLEANING

REPLACING THE WATER FILTER

The water ﬁlter should be replaced every 6

months based on a ﬂow rate of

0.75 gpm-0.80 gpm (1.89- 2.27 Lpm) that ﬁlters

200 gallons (757 L) of water.

NOTE: If the ﬁlter is not installed correctly,

water may dispense at a lower ﬂow rate and

there will be slower ice production. Improper

ﬁlter installation may also cause the water ﬁlter

housing to leak.

1. To open, push the water ﬁlter door up,

which is located at the upper left above the

refrigerator or freezer compartment.

2. Turn the water ﬁlter 90° counterclockwise

to unlock.

3. Pull the ﬁlter out of the housing.

4. Remove the water ﬁlter cap from the water

ﬁlter.

La page charge ...

Jenn-Air JBRFR36IGX Le manuel du propriétaire

Jenn-Air JBRFR36IGX Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents