Yamaha CRW-2200IX Le manuel du propriétaire

Marque: Yamaha

Modèle: CRW-2200IX

Catégorie: Lecteurs de disques optiques

Taper: Le manuel du propriétaire

Ce manuel convient également à

CRW2200IX

CRW2200IX (W)

4th draft

2001.06.22

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party: Yamaha Electronics Corporation, USA.

Address: 6660 Orangethorpe Avenue

Buena Park, CA 90620

Telephone: 714-522-9105

Fax: 714-670-0108

Type of Equipment: CD Recordable/Rewritable Drive

Model Name: CRW2200IX

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interference that

may cause undesired operation.

See user manual instructions if interference to radio reception is suspected.

FCC INFORMATION (U.S.A.)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements.

Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables.

Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void

your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class

“B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product

in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses

radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause

interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that

interference will not occur in all installations. If this product is found to be the source of interference, which can be determined

by turning the product “OFF” and “ON”, please try to eliminate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by the interference.

Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change

the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this

type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corporation, USA.

6660 Orangethorpe Avenue, Buena Park, CA 90620 U.S.A.

CAUTION

Use of controls or adjustments or performance of

procedures other than those specified herein may result

in hazardous radiation exposure.

Laser Product Class: Class 1

Laser Diode Properties

Wavelength: 780-787 nm

Pulse Durations and Max. Output

at the lens of the Laser Pickup Unit

Read Mode: 0.7mW (Continuous)

Write Mode: Max. 38mW

(for 166ns, Min. Cycle 86.6ns)

ACHTUNG

Halten Sie sich beim Bedienen und Einstellen der

Bedienungselemente sowie bei der Bedienungsabfolge

an die Anleitung, da sonst gefährliche Strahlen austreten

können.

ATTENTION

L’emploi de commandes, de réglages ou un choix de

procédures différents des spécifications de cette

brochure peut entraîner une exposition à d’éventuelles

radiations pouvant être dangereuses.

PRECAUCION

El usar los controles o ajustar o realizar procedimientos

diferentes a los especificados aquí resultará en

peligrosas exposiciones a la radiación.

VARO! AVATTAESSA JA SUOJALUKITUS OHITETTAESSA

OLET ALTTINA NÄKYMÄTTÖMÄLLE

LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.

VARNING! OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR

ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD.

BETRAKTA EJ STRÅLEN. STRÅLEN ÄR FARLIG.

Laserprodukt-Klasse: Klasse 1

Eigenschaften der Laserdiode

Wellenlänge: 780-787 nm

Impulsdauer und max. Ausgang an der Linse der

Laser-Abtasteinheit

Lesemodus: 0,7mW (kontinuierlich)

Schreibmodus: Max. 38mW

(für 166ns, Zyklusmin. 86,6ns)

Classe du produit laser: Classe 1

Caractéristiques de la diode laser

Longueur d’onde: 780-787 nm

Durée des impulsions et sortie maximum depuis

la lentille du bloc capteur optique

Mode de lecture: 0,7mW (continue)

Mode de gravure: max. 38mW

(pour 166ns, cycle min. 86,6ns)

Clase de producto láser: Clase 1

Propiedades del diodo láser

Longitud de onda: 780-787 nm

Duración del pulso y potencia de salida máxima

en el objetivo de la unidad captora láser

Modo de lectura: 0,7mW (continua)

Modo de escritura: máx. 38mW

(para 166ns, ciclo mínimo 86,6ns)

CLASS 1 LASER PRODUCT

LASER KLASSE 1 PRODUKT

LUOKAN 1 LASERLAITE

KLASS 1 LASER APPARAT

PRODUIT LASER DE CLASSE 1

DANGER - VISIBLE AND / OR INVISIBLE LASER

RADIATION WHEN OPEN. AVOID DIRECT EXPOSURE

TO BEAM.

CAUTION - VISIBLE AND / OR INVISIBLE LASER RADIATION WHEN OPEN.

AVOID EXPOSURE TO BEAM.

VARNING - SYNLIG OCH / ELLER OSYNLIG LASERSTRÅLNING NÄR DENNA

DEL ÄR ÖPPNAD. STRÅLEN ÄR FARLIG.

VARO ! AVATTAESSA OLET ALTTIINA NÄKYVÄLLE JA / TAI

NÄKYMÄTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.

VARNING - SYNLIG OCH / ELLER OSYNLIG LASERSTRÅLNING NÄR DENNA DEL

ÄR ÖPPNAD. BETRAKTA EJ STRÅLEN.

VORSICHT ! SICHTBARE UND / ODER UNSICHTBARE LASERSTRAHLUNG

WENN ABDECKUNG GEÖFFNET. NICHT DEM STRAHL AUSSETZEN.

ATTENTION - RADIATION VISIBLE ET / OU INVISIBLE LORSQUE L’APPAREIL

EST OUVERT. EVITEZ TOUTE EXPOSITION AU FAISCEAU.

COMPLIES WITH 21 CFR CHAPTER1, SUBCHAPTER J.

OWNER’S MANUAL

English

PLEASE READ THE FOLLOWING WARNING AND

PLEASE READ THE FOLLOWING WARNING AND PLEASE READ THE FOLLOWING WARNING AND

PLEASE READ THE FOLLOWING WARNING AND

CAUTION CAREFULLY TO PROTECT YOUR PERSONAL

CAUTION CAREFULLY TO PROTECT YOUR PERSONAL CAUTION CAREFULLY TO PROTECT YOUR PERSONAL

CAUTION CAREFULLY TO PROTECT YOUR PERSONAL

SAFETY AND PREVENT DAMAGE TO THE DEVICE.

SAFETY AND PREVENT DAMAGE TO THE DEVICE.SAFETY AND PREVENT DAMAGE TO THE DEVICE.

SAFETY AND PREVENT DAMAGE TO THE DEVICE.

These precautions explain how to use the device correctly and safely, thereby preventing injury to

yourself or to others. This section has been sub-divided into a WARNING section and a CAUTION

section, according to the likelihood and nature of any potential injuries or damage inflicted. They relate

to your personal safety, and also help you minimize the risk of damaging the device. Please read these

sections carefully before proceeding.

WARNING

Always follow these basic precautions to prevent short-circuit, damage, fire, or other hazards,

and to prevent serious injury or death from electrical shock. These precautions include, but are

not limited to, the following:

● To avoid risk of electrical shock or fire, do not attempt to open or disassemble the device.

● To avoid risk of eye damage or blindness, do not look inside the device.

● To avoid the risk of personal injury or electrical shock, do not insert your fingers, or foreign objects

into the device.

● To avoid the risk of electrical shock, fire, or personal injury, do not expose the device to rain, use it

near water, or in damp or wet conditions, or place containers that contain liquids (they may spill into

the unit) on the device.

● To avoid risk of personal injury, electrical shock, fire, or damage to the unit, follow the Owner’s

Manual carefully.

● If unusual smells, sounds or smoke come from the device, turn off the computer immediately to

avoid the risk of electrical shock, fire or damage to the device, and return the device to the place of

purchase, or alternatively, to your nearest Yamaha dealer (listed at the back of this manual).

● Make sure the computer is electrically grounded to avoid the risk of electrical shock.

● Always unplug the computer from the electrical outlet, and do not touch the plug with wet hands, as

there is an increased risk of electrical shock.

● The drive should not be exposed to temperatures outside the range 5 – 35 °C (41 – 95 °F) to avoid

risk of malfunction, fire or personal injury.

● To avoid the risk of electrical shock or fire, be sure to use the correct voltage rating.

● Clean the AC power plug regularly, especially the blades, to avoid the risk of insulation failure or fire

due to humidity.

● Do not pull on the cord itself when disconnecting from the electrical outlet, or let objects rest or roll

over the cord, as the cord can be damaged and cause electrical shock or fire.

SAFETY PRECAUTIONS

iii

● Insert the AC plug firmly, as a poor connection can result in electrical shock or fire.

● Only use the included AC adapter, as malfunction or fire may result.

● Do not connect too many devices to a single electrical outlet, or use voltages exceeding the rated

voltage as this may cause overheating and fire.

CAUTION

Always follow these basic precautions to prevent physical injury to yourself or others, or damage

to the instrument or other property.

● To avoid the risk of electrical shock or fire, always unplug the computer from the electrical outlet if it

will not be used for a prolonged period of time, or if there is a risk of lightning.

● Do not expose the device to excessive vibration, heat, cold or dust, as doing so may result in damage

to the unit’s front panel or its internal components.

● Do not use the device near other products such as televisions, radios, or speakers as this may cause

interference, which can affect the proper operation of the device or other devices.

● To avoid damage to the device or personal injury, always place the device in a stable position.

● Always place the device horizontally (see Owner’s Manual) to avoid the risk of lost written data.

● Always remove any disc from the disc tray before transporting the device as written data may be lost.

● Use a soft, dry cloth to wipe the device. Do not use benzene, paint thinners, detergents, or

chemically treated wiping cloths as these may damage the unit.

Do not place vinyl, plastic, or rubber objects on the device as chemical reactions can cause damage

to the device.

● Do not rest your weight on or place heavy objects on the device, or use excessive force on the

buttons, switches or connectors, as damage to the unit or personal injury may occur.

● Do not listen to audio with headphones at high volume for prolonged periods of time as your hearing

may be damaged as a result.

● Before using the device, always turn down the volume as sudden bursts of sound can result in

hearing damage.

● Do not place the device anywhere near sources of magnetic interference as operational stability may

be adversely affected.

● Have the device serviced regularly (about once a year) to avoid internal dust buildup that can cause

malfunction, damage or fire. For service information, contact the store of purchase, or your nearest

Yamaha dealer (listed in the back of this manual).

● Do not allow the plug of the AC adapter to come into contact with metal as a short circuit can result

and cause a malfunction or damage to the device.

● Do not wrap the power cord around the AC adapter as it may become disconnected and cause a malfunction.

■ About handling CD-R/RW discs

1. Do not store discs in areas subject to excessive humidity or heat (i.e., in direct sunlight or

near a heater).

2. Do not touch the surface of a disc.

When handling a disc, hold it by the edges.

3. Remove dust and dirt from the surface of a disc.

Use an air-blower (i.e., camera lens blower) to remove dust. The surface of a disc may be

scratched if wiped with a dry cloth.

4. Do not stick labels on the surface of a disc.

5. Do not write on the surface of a disc except where indicated.

6. Do not clean discs with chemicals or detergents.

7. Do not bend or drop discs.

8. Use only circular discs. Do not use irregularly shaped discs, such as star, heart or card

shaped, etc., as these could damage your new CD-R/RW drive.

■ Precautions for Transportation

Before transporting the device, always put it in its original box. If the device is transported

without adequate packing, the internal components may be damaged and cause the device

to malfunction.

■ Copyrights

When writing to a CD-R/RW, make sure that you do not infringe on any copyrights. It is

illegal to copy audio CDs for non-personal use. When backing up software, make sure that

you do not infringe on any software copyrights for that product.

■ WARRANTY

YAMAHA AND ITS SUPPLIERS ACCEPT NO LIABILITY FOR THE LOSS OF ANY DATA

OR ANY PROBLEMS CAUSED AS A RESULT. AS A PRECAUTION, IT IS

RECOMMENDED THAT THE DISCS BE TESTED AFTER THEY HAVE BEEN WRITTEN

TO. FURTHERMORE, UNDER NO CIRCUMSTANCES DOES YAMAHA AND ITS

SUPPLIERS GUARANTEE THE RELIABILITY OF THE DISCS.

1. The information contained in this manual is subject to change

without prior notice.

2. All trademarks contained in this manual belong to their respective

owners.

3. Yamaha does not bear any responsibility for a problem that occurs

as a result of any operations carried out other than those stated in

the manual included with the drive.

4. Reproduction of this manual, either in part or in full, is expressly

forbidden.

Table of Contents

Introduction........................................................................ 1

Features of the CRW2200IX Drive.................................................... 1

Before Use ......................................................................... 4

System Requirements.......................................................................... 4

Supported Discs................................................................................... 6

Serial Number ..................................................................................... 8

Front and Rear of Unit............................................................ 9

Front Panel .......................................................................................... 9

Rear Panel ......................................................................................... 10

Setup Procedures ................................................................11

Windows Users ................................................................................. 11

Macintosh Users................................................................................ 12

Install the CD Writing Software........................................................ 13

Set Up the CRW2200IX Drive......................................................... 13

Configuring for the Operating System.............................................. 18

Operation..........................................................................20

Connecting and Disconnecting IEEE1394 Devices.......................... 20

Loading a Disc .................................................................................. 21

Ejecting a Disc .................................................................................. 21

Ejecting a Disc in an Emergency ...................................................... 22

Troubleshooting..................................................................23

Appendix...........................................................................28

Connecting Multiple IEEE1394 Peripherals Together...................... 28

Writing Modes................................................................................... 30

About the Firmware .......................................................................... 32

LED Indicator Messages................................................................... 33

CRW2200IX Specifications............................................................. 34

Index.................................................................................................. 37

This document may not, in whole or in part, be copied, photocopied, reproduced,

translated, transmitted, or reduced to any electronic medium of machine readable

form without prior consent in writing from Yamaha.

Windows is a registered trademark of Microsoft Corporation.

Apple, Macintosh, Mac OS, and FireWire are registered trademarks of Apple

Computer, Inc.

SafeBurn™ is a trademark of Yamaha Corporation.

All other trademarks are the property of their respective companies.

Introduction

High speed writing/reading

The CRW2200IX drive supports up to 20X-speed writing of CD-R discs,

and up to

10X-speed writing/rewriting of CD-RW discs.

Furthermore, the drive supports data

reading and digital audio data extraction at up to 40X speed.

Easy setup

Implementation of an IEEE1394 interface (also known as FireWire or i.LINK)

eliminates the need for drive configurations (device ID, termination, etc.). You can

connect and start using the drive whenever you wish without restarting your

computer.

SafeBurn™ (Enhanced write stability technology)

Generous 8MB of buffer memory

Because of the large data storage area, stable disc writing is possible even at fast

speeds.

Buffer Underrun Protection

When data transfer from the host PC is interrupted, Buffer Underrun Protection is

activated to keep precious CD-R discs from going to waste. (

→

P. 3)

Optimum Write Speed Control

Before writing to a CD-R, the CRW2200IX drive checks the disc’s capability and

automatically selects the optimum writing speed

for greater reliability. Even if the

writing speed of the CD-R disc you are using is faster than the setting speed on the

writing software, the setting speed still takes precedence.

Reliable writing

Yamaha’s proprietary Pure-Phase Laser System (patent applied for)

This technology reduces phase interference of the laser beam, so that it projects

accurately onto the disc. Jitter value, an important measure of recording quality, has

been improved 25% compared with Yamaha models not using this technology.

Running OPC (Optimum Power Control)

Running OPC automatically adjusts the output of the laser according to the

characteristics of the disc being used. Running OPC provides greatly enhanced

recording reliability for various manufacturer’s discs.

Features of the

CRW2200IX

Drive

Introduction

High-fidelity digital audio

The CRW2200IX drive supports extraction of digital audio data at up to 40X speed,

as well as the recording of digital sound with complete fidelity even when writing at

20X speed.

CD TEXT support

Information such as the song name or artist name can be recorded on Audio CDs

using CD creation software. The text data on the created disc can be displayed on a

CD player that is compatible with the CD TEXT format.

*1 16X- or 20X-speed writing is enabled with the Partial CAV method. (

→

P. 7)

*2 10X-speed writing/rewriting is enabled with the CLV method and the 4X-10X Full CAV method. (

→

P. 8)

*3 The optimal writing speed automatically selected will be between 8X speed and the maximum speed designated

for that disc. If the disc is rated at lower than 8X speed writing, you need to designate the most suitable writing

speed manually.

About IEEE1394

IEEE1394 is an industry standard approved by IEEE (Institute of Electrical and

Electronics Engineers). The serial interface has a broad bandwidth and is fast

enough to transfer large amounts of digital video and audio data bi-directionally

between electronic devices including computer peripherals. Also known as

FireWire and i.LINK, the IEEE1394 interface allows units to transfer data or

various controls over a single IEEE1394 interface cable. Unlike legacy serial

interfaces such as RS-232C, IEEE1394 allows for daisy-chaining devices (serial

connection) with data transfer possible between any two devices on the chain.

IEEE1394 also supports a tree (parallel) connection of devices. In addition to

this flexibility, IEEE1394 also eliminates the need for complicated settings such

as device ID and termination as found with SCSI (Small Computer System

Interface) type interfaces. As of this writing, IEEE1394 supports three different

data transfer rates: 100 Mbps, 200 Mbps, and 400 Mbps.

Introduction

Buffer Underrun Defined

CD-R/RW drives are equipped with buffer memory. This memory temporarily

stores data while a disc is being recorded. When buffer memory becomes empty

(due to unexpected interruptions or the system’s inability to keep up with the

writing process), a writing error occurs. This error is known as a “buffer

underrun error.”

A Buffer Underrun Error will permanently ruin the disc.

Yamaha Buffer Underrun Protection

Buffer Underrun Protection is featured in Yamaha’s CRW2200 series CD-R/

RW drives. When a buffer underrun is about to occur, a buffer underrun error is

prevented by temporarily suspending the writing process. Writing resumes when

enough data has accumulated again in buffer memory. Buffer Underrun

Protection on the CRW2200 series is extremely accurate, resulting in seamless

recording between stop and continuation points.

Yamaha Buffer Underrun Protection ensures error-free results.

Test-writing for Buffer Underrun

You can run a check for the likely occurence of Buffer Underrun by Test-writing a CD-RW

disc. The occurrence of a Buffer Underrun depends on your computer system and the CD-R/

RW drive.

Most writing software includes test-writing functions to check the likely occurrence of

Buffer Underrun before actually writing the disc.

Buffer Underrun Protection is set to ON by default. Test-writing is not available in this

setting. To use test-writing with your computer system, the Buffer Underrun Protection

should be set to OFF. (For more details, refer to the documentation that came with your CD

writing software.)

➀➁➂

Data

If data transfer is

interrupted...

Data is stored in

buffer memory...

then buffer memory

begins to empty

When no data is left

in buffer memory...

(Buffer Underrun)

and then written

to disc

writing fails

(Buffer Underrun

Error)

➀➁

If data transfer is

interrupted...

Even if data transfer is interrupted at

any time, it will resume seamlessly...

and buffer memory is

about to empty...

and enough data has accumulated

in buffer memory...

writing is suspended writing resumes

Before Use

In order to use the CRW2200IX drive, your computer system will need to meet the

following requirements.

Notes

• The CRW2200IX drive may not write at the maximum speed depending on your computer’s

system configuration.

• For best performance, refer also to the CD writing software documentation for system

requirements (e.g., hardware, OS, etc.).

Windows Users

Computer

• PC/AT-compatible computers

• CPU: Pentium II, 300 MHz or faster.

•RAM: 64 MB or more.

• IEEE1394 port: At least one IEEE1394 port is required.

Note

This port may be a built-in (onboard) type, or provided with a PCI expansion card or a CardBus

card. If you newly install an IEEE1394 PCI or CardBus interface card, your computer should have

an empty PCI expansion slot or a CardBus slot. For more information about the IEEE1394

interface card, refer to “IEEE1394 Interface Card (PCI or CardBus)” shown below.

Operating System (OS)

Windows 98 Second Edition, Windows Me, Windows 2000 Professional

CD-ROM Drive

You may need another CD-ROM drive for any CD-related operations (playback

of an audio CD, installation from CD-ROM, etc.) until you verify that the

CRW2200IX drive is successfully installed. Also you may need another CD-

ROM drive if you are planning to copy a CD-ROM directly to a CD-R/RW disc

on the CRW2200IX drive.

Note

The CRW2200IX drive cannot be used to install an operating system or to boot your

computer from a CD-ROM containing an operating system.

IEEE1394 Interface Card (PCI or CardBus)

For the CRW2200IX drive to work properly with your computer, your IEEE1394

interface card must be OHCI compliant. As of this writing, Yamaha has verified

compatibility with the following cards:

System Requirements

Manufacturer Product Card Type

Advansys ASB30400 PCI

SIIG NN2603 PCI

Before Use

Notes

• For the latest information about approved IEEE1394 interface cards, check the YAMAHA

CD-R/RW Drive web site.

URL: http://www.yamaha.co.jp/english/product/computer/

• Some IEEE1394 interface cards may not work properly with your computer. Be sure to

check for compatibility not only with your computer, but also with the CRW2200IX drive

before purchasing a new IEEE1394 interface card.

• Even if you already have an IEEE1394 interface card installed and working properly in

your computer, it may not be compatible with the CRW2200IX drive. Refer to the

requirements listed on the previous page and to your interface card documentation to check

for compatibility.

Macintosh Users

Computer

• Macintosh computers with a built-in FireWire port

• CPU: PowerPC G3, 300 MHz or faster.

• RAM: 64 MB or more.

Operating System

Mac OS 8.6, 9, 9.1 (Except for Classic with Mac OS X)

Note

FireWire software version 2.2.2 or later is recommended for the CRW2200IX drive to work

properly. The latest software is available from the Apple support web site.

CD-ROM Drive

You may need another CD-ROM drive for any CD-related operations (playback of an

audio CD, installation from CD-ROM, etc.) until you verify that the CRW2200IX

drive is successfully installed. Also you may need another CD-ROM drive if you are

planning to copy a CD-ROM directly to a CD-R/RW disc on the CRW2200IX drive.

Note

The CRW2200IX drive cannot be used to install an operating system or to boot your

computer from a CD-ROM containing an operating system.

CD Writing Software

The CRW2200IX drive requires a CD writing software to write onto a CD-R/RW disc.

Make sure your CD writing software supports the CRW2200IX drive.

Note

For details about how to install and use the software, refer to the documentation that came with it.

Hard Drive Space

When writing to a CD-R/RW disc, you will need a working area (50 to 100 MB of

free space) on the hard drive. If you want to create an image file containing all the

data to be written to the CD-R/RW disc, in addition to the working area, you will

need as much hard drive space as that data (up to 900 MB in total). However, this

additional hard drive space for the image file is not needed when you are writing

directly from a hard drive or CD-ROM drive, etc. (on-the-fly writing).

About disk image files

You can collect data files into a single disk image file for a CD-R/RW disc. Also, note that an

image file is useful when writing multiple discs with the same content. For further details, refer to

the documentation that came with your CD writing software.

Before Use

The CRW2200IX drive can write to discs that carry the following logos:

*1 Compatible with Orange Book Part 2.

*2 Compatible with Orange Book Part 3 Vol. 1.

*3 Compatible with Orange Book Part 3 Vol. 2.

Note

To find current information about approved discs for the drive, visit the YAMAHA CD-R/RW

Drive web site.

URL: http://www.yamaha.co.jp/english/product/computer/

Supported Discs

CD-R discs

The CRW2200IX drive can write to these discs at 1X, 2X, 4X, 8X, 12X, 16X,

or 20X speed. These discs can be played back in a CD-ROM drive or a CD

player.

Notes

• 16X- or 20X-speed writing is enabled with Partial CAV method. (

→

P. 7)

• For 8X or faster writing, use CD-R discs that match their respective writing

speeds.

CD-RW discs

There are two types of CD-RW discs: those that support write/rewrite speeds

of 1X, 2X, and 4X, and those that support only 2X. The CRW2200IX drive

can write/rewrite at 2X or 4X speed on the first type of disc, and at 2X on the

second type of disc. These discs can be read/played on a device (e.g., CD-

ROM drive) that supports “CD-RW.”

High Speed CD-RW discs

These discs allow writing/rewriting at 4X to 10X speeds. The CRW2200IX

drive can write/rewrite these discs at 4X, 8X, or 10X speed. These discs can be

read/played by a CD-RW drive that bears the High Speed CD-RW logo, or by

a device (e.g., CD-ROM drive) that supports “CD-RW.”

Note

10X-speed writing/rewriting is enabled with the CLV method, and the 4X-10X

Full CAV method. (

→

P. 8)

• In order to write, erase, or read these discs using a CD-R/RW

drive, a drive bearing the High Speed CD-RW logo must be

used. When using a CD-ROM drive to read these discs, the

drive must be capable of reading CD-RW discs.

• If these discs are used in a CD-R/RW drive not bearing the

High Speed CD-RW logo, the discs may not be recognized,

resulting in the computer not operating correctly or other

malfunctions occurring.

• Refer to the page at the URL below before attempting to read

these discs on a Yamaha CD-R/RW drive not bearing the

High Speed CD-RW logo.

URL: http://www.yamaha.co.jp/english/product/computer/

Before Use

About the Orange Book

The Orange Book standard defines how all recordable discs (including CD-R and CD-RW) are

written. Part 2 of the Orange Book standard relates to CD-R discs, and Part 3 to CD-RW discs.

The standard was named after the color of the book’s cover.

About CD-ROMs

A CD-ROM disc is a compact disc containing high-density read-only data. It has

many applications, including the playback of music and video, the archiving of

data, as well as on-line documentation. The following are descriptions of each

CD-ROM format:

CD-DA: Up to 79 minutes of stereo audio is written in 16-bit resolution at a

sampling rate of 44.1 kHz for a 79 minute disc.

Data CD: Up to 700 megabytes of computer data is stored in standard ISO9660

format for a 700 MB disc.

Video CD: These hold movies in which video and audio data has been

compressed using MPEG-1 technology.

About Partial CAV (Constant Angular Velocity)

Writing to a CD-R disc is normally done using the CLV (Constant Linear

Velocity) method. In this method, the disc rotation speed is adjusted so as to

keep a constant data transfer rate at any portion of the disc. In other words, the

disc rotation speed will vary in CLV writing.

In contrast, the CAV (Constant Angular Velocity) method uses a constant disc

rotation speed for all portions of the disc so that the data transfer rate will vary.

Because the CAV method has the advantage of largely increasing the data

transfer rate with a minimum load to the drive’s mechanism (compared to CLV’s

rotation speed adjustment), many current CD-ROM drives use the CAV method.

CD formats define the constant linear density of written data (data should be

written onto the disc at a constant pitch) so that the amount of recorded data per

disc rotation will increase as the writing point moves from the inner to the outer.

In other words, in CAV writing, the outer portion has an increased data transfer

rate.

The CRW2200IX drive uses the CAV method in the inner portions as well as

the CLV method in the outer portions (Partial CAV) in order to enable up to

20X-speed writing. The drive will control the disc rotation speed to start writing

at 12X speed in the inner portions, gradually accelerating up to 20X speed and

maintaining 20X speed in the outer portions.

Before Use

Once you have taken the CRW2200IX drive out of its packaging, you should

immediately note down the serial number found at the bottom of the drive with the

bar code. You may need to refer to this number when requesting Customer Support

services. In the box below the following diagram, write down the 10-character serial

number (consisting of 3 letters followed by 7 digits).

About 10X-speed writing/rewriting of a High Speed CD-RW disc

10X-speed writing/rewriting of a High Speed CD-RW disc is enabled with the

CLV method, and the 4X-10X Full CAV method. Commonly, writing/rewriting

is enabled with the CLV method. When writing/rewriting with packet writing

(

→

P. 31), you can also select the Full CAV method. For more details, refer to the

documentation that came with your CD writing software. (Make sure that your

CD writing software supports the Full CAV method.) For direct editing of a file

on a CD-RW disc, the Full CAV method is recommended.

Serial Number

Serial No.

Serial number

(3 letters and 7 digits)

Front and Rear of Unit

➀

➀➀

➀

Power LED

Lights up in green when the power of the drive is turned on.

➁

➁➁

➁

Disc tray

The disc tray is used to hold the disc. It slides out from the drive unit when a disc needs to

be loaded or unloaded. (

→P. 21)

➂

➂➂

➂

Manual eject hole

Only use this if no other method is available for unloading a disc. (→P. 22)

➃

➃➃

➃

Eject button

Press this button when you need to open or close the disc tray. Remove the disc after the

disc tray has opened. (

→P. 21)

➄

➄➄

➄

Headphone jack

You can connect stereo headphones to this stereo mini jack and listen to an audio CD

loaded in the drive.

➅

➅➅

➅

Headphone volume control

Adjust this control to set a suitable volume level when listening to an audio CD using the

headphone jack. Slide the knob to the left to decrease the volume and to the right to

increase it.

➆

➆➆

➆

LED

Indicates the operation status of the CRW2200IX drive. (→P. 33)

Front Panel

➃➁➂➀

➄➅ ➆

Front and Rear of Unit

➀

➀➀

➀

LINE OUT jacks (L/R)

To listen to audio CDs with the CRW2200IX drive, connect these to the line level input

(LINE IN) of the stereo equipment with a standard stereo phono cable (sold separately).

➁

➁➁

➁

Power switch (STANDBY/ON)

Turns the power on or off. (→P. 13, 15)

➂

➂➂

➂

DC-IN connector

Insert the included AC adapter connector. (→P. 13)

➃

➃➃

➃

IEEE1394 ports

Insert the connector of the IEEE1394 cable here. (→P. 16, 17)

Rear Panel

➃

➁➀➂

Setup Procedures

This flowchart shows the procedure for setting up the CRW2200IX drive.

For easy cross-referencing, the relevant pages in this manual are given.

Windows Users

Do you have an appropriate IEEE1394

interface card?

The card should be compatible with your

computer.

Does your computer have a

built-in IEEE1394 port?

STEP

Install the CD writing software.

Before installing the software, disconnect

all IEEE1394 devices.

STEP

Make sure that system configuration

(CPU, RAM, OS, etc.) of your computer

meets the requirements of the

CRW2200IX drive (→

→→

→P. 4, 5).

Set up the CRW2200IX drive

(→

→→

→P. 13 – 17).

1 Turn your computer and the drive both

on before connecting.

2 Connect your computer and the drive

using the IEEE1394 interface cable that

came with the drive.

You may need a different cable

depending on the IEEE1394 port

connector on your computer (→

→→

→P. 17).

Make sure that the

CRW2200IX drive is correctly

recognized (→

→→

→P. 18).

Start using the CRW2200IX drive

Use the drive to create an audio CD, to backup data

on your hard drive, or for whatever purpose suits

your needs.

Install the card to your

computer.

Read the documentation that

came with the card and properly

set up your computer.

Purchase an IEEE1394 card.

See page 3 for more information about

approved IEEE1394 interface cards that have

been tested for compatibility with the

CRW2200IX drive.

STEP

YES

La page charge ...

Yamaha CRW-2200IX Le manuel du propriétaire

Marque: Yamaha

Modèle: CRW-2200IX

Catégorie: Lecteurs de disques optiques

Taper: Le manuel du propriétaire

Ce manuel convient également à

CRW2200IX

Télécharger le PDF

rapport

dans d''autres langues

italiano: Yamaha CRW-2200IX Manuale del proprietario
English: Yamaha CRW-2200IX Owner's manual
Deutsch: Yamaha CRW-2200IX Bedienungsanleitung
Nederlands: Yamaha CRW-2200IX de handleiding
dansk: Yamaha CRW-2200IX Brugervejledning
svenska: Yamaha CRW-2200IX Bruksanvisning
Türkçe: Yamaha CRW-2200IX El kitabı
suomi: Yamaha CRW-2200IX Omistajan opas
română: Yamaha CRW-2200IX Manualul proprietarului

Yamaha CRW-2200IX Le manuel du propriétaire

Ce manuel convient également à

Yamaha CRW-2200IX Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents