Aeg-Electrolux S72398KA6 Manuel utilisateur

Marque: Aeg-Electrolux

Modèle: S72398KA6

Catégorie: Frigos

Taper: Manuel utilisateur

User manual

Notice d’utilisation

Electronic-Fridge

Réfrigérateur

SANTO 72398-6 KA

Dear Customer

Thank you for choosing one of our high-quality products.

With this appliance you will experience the perfect combination of

functional design and cutting edge technology.

Convince yourself that our appliances are engineered to deliver the best

performance and control - indeed we are setting the highest standards of

excellence.

In addition to this you will find environmental and energy saving aspects as

an integral part of our products.

To ensure optimal and regular performance of your appliance please read

this instruction manual carefully. It will enable you to navigate all processes

perfectly and most efficiently.

To refer to this manual any time you need to, we recommend you to keep

it in a safe place, and please pass it to any future owner of the appliance.

We wish you much joy with your new appliance.

The following symbols are used in this manual

Important information concerning your personal safety and information on

how to avoid damaging the appliance

General information and tips

Environmental information

Contents

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Appliance Packaging Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Disposal of old Appliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Remove transport safeguard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Your appliance needs air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Installation Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Rear spacer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Fitting the Door Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Rehingeing the door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Prior to Inital Start-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Starting up - setting the temperature . . . . . . . . . . . . . . . . . . . . . . .12

Interior Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Storage shelves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Door rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Bottle Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Quick chill shelf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Bottle-and Can Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Dismantling of the Bottle - and Can Holder . . . . . . . . . . . . . . . . . . . . .16

Installation of the carbon filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Changing the carbon filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Fresh food refrigeration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Defrosting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Switching off the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Cleaning and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Energy Saving Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

What to do if . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Correcting Malfunctions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Changing the light bulb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Regulations, Standards, Guidelines . . . . . . . . . . . . . . . . . . . . . . . . .23

Safety

The safety aspects of our refrigerators/freezers comply with accepted

technical standards and the German Appliance Safety Law. Nevertheless, we

consider it our obligation to make you aware of the following safety

information:

Intended use

• The refrigerator is intended for use in the home. It is suitable for cooling

food. If the appliance is used for purposes other than those intended or

used incorrectly, no liability can be accepted by the manufacturer for any

damage that may be caused.

• Alterations or changes to the freezer are not permitted for reasons of safety.

• If you use the refrigerator in a commercial application or for purposes

other than the cooling of foods, please observe all valid legal regulations

for your application.

Prior to initial start–up

• Check the refrigerator for transport damage. Under no circumstance

should a damaged appliance be plugged in! In the event of damage, please

contact the retailer.

Refrigerant

The refrigerant isobutane (R600a) is contained within the refrigerant circuit

of the appliance, a natural gas with a high level of environmental

compatibility, which is nevertheless flammable.

• During transportation and installation of the appliance, be certain that

none of the components of the refrigerant circuit become damaged.

• If the refrigerant circuit should become damaged:

– avoid open flames and sources of ignition;

– thoroughly ventilate the room in which the appliance is situated.

Safety of children

• Packaging (e.g. wraps, polystyrene) can be dangerous for children. There is

a risk of suffocation! Keep packaging material away from children!

• Please make old appliances unusable prior to disposal. Pull out the mains

plug, cut off the mains cable, break or remove spring or boltcatches, if

fitted. By doing this you ensure that children cannot lock themselves in

the fridge when playing (there is risk of suffocation!)or get themselves

into other dangerous situations.

• This appliance is not intended for use by persons (including children) with

reduced physical, sensory or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision or instruction

concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the

appliance. !

Daily Operation

• Do not operate any electrical appliances in the refrigerator/freezer (e.g.

electric ice cream makers, mixers etc.).

• Before cleaning the appliance, always switch it off and unplug it, or pull

the house fuse or switch off the circuit breaker.

• When unplugging always pull the plug from the mains socket, do not pull

on the cable.

In case of malfunction

• If a malfunction occurs on the appliance, please look first in the "What to

do if ..." section of these instructions. If the information given there does

not help, please do not perform any further repairs yourself.

• Refrigerators/freezers may only be repaired by qualified service engineers.

Improper repairs can give rise to significant hazards. If your appliance needs

repairing, please contact your local Service Force Centre.

Disposal

Appliance Packaging Information

All materials are environmentally sound! They can be dumped or burned at

an incinerating plant without danger!

About the materials: The plastics can be recycled and are identified as

follows:

>PE< for polyethylene, e.g. the outer covering and the bags in the interior.

>PS< for polystyrene foam, e.g. the pads, which are all free of

chlorofluorocarbon.

The carton parts are made from recycled paper and should be disposed of

at a waste-paper recycling collection location.

Disposal of old Appliances

For environmental reasons, refrigeration appliances must be disposed of

properly. This applies to your old appliance, and - at the end of its service

life - your new appliance as well.

Warning! Before disposing of old appliances make them inoperable. Remove

plug from mains, sever the power cable, remove or destroy any snap or latch

closures. This eliminates the danger that playing children lock themselves

into the appliance (danger of suffocation!) or place themselves into other

life-endangering situations.

Disposal:

• The appliance may not be disposed of with domestic waste or bulky refuse.

• The refrigerant circuit, especially the heat exchanger at the back of the

appliance, may not be damaged.

• The symbol on the product or on its packaging indicates that

this product may not be treated as household waste. Instead it

should be handed over to the appropriate collection point for the

recycling of electrical and electronic equipment. By ensuring this

product is disposed of correctly, you will help prevent potential

negative consequences for the environment and human health,

which could otherwise be caused by inappropriate waste handling of

this product. For more detailed information about recycling of this

product, please contact your local council, your household waste

disposal service or the shop where you purchased the product.

Remove transport safeguard

The appliance and the interior fittings are protected for transport.

•Remove all adhesive tape and packing pieces from the interior of the

appliance.

Your appliance is equipped with shelf

retainers that make it possible to

secure the shelves during

transportation.

To remove them proceed as follows:

Move the shelf retainers in the

direction of the arrow, raise the shelf

from the rear and push it forward

until it is freed and remove the

retainers.

100 mm10 mm

10 mm

NP007

Your appliance needs air

For safety reasons, minimum

ventilationmust be as shown Fig.

Attention: keep ventilation

openings clear of obstruction;

If installation next to a source of heat is unavoidable, the following

minimum clearances must be maintained at the sides of the appliance:

– for electric cookers 3 cm;

– for oil and coal fired ranges 30 cm.

If these clearances cannot be maintained a heat insulating pad is required

between the cooker and the refrigeration appliance.

If the refrigeration appliance is installed next to another refrigerator or

freezer a clearance of 5 cm at the sides is required, in order to prevent the

formation of condensation on the outside of the appliance.

Installation

Installation Location

The appliance should be set up in a well ventilated, dry room.

Energy use is affected by the ambient temperature. The appliance should

therefore

– not be exposed to direct sunlight;

– not be installed next to radiators, cookers or other sources of heat;

– only be installed at a location whose ambient temperature corresponds to

the climate classification, for which the appliance is designed.

The climate classification can be found on the serial plate, which is located

at the left on the inside of the appliance.

The following table shows which ambient temperature is correct for each

climate classification: each climate classification:

Climate classification for an ambient temperature of

SN +10 bis +32 °C

N +16 bis +32 °C

ST +18 bis +38 °C

T +18 bis +43 °C

1. Screw the top handle

bracket to the handle rod

(1). Fit the bottom handle

bracket on the lower left-

hand side of the door (2).

2. Fit the top handle bracket

on the top left-hand side

of the door (3) and screw

the handle rod to the

bottom handle bracket (4).

Attention!

Do not overtighten the

screws (max. 2 Nm) as you

may damage the door

handles.

Fitting the Door Handle

Rear spacers

Fit the rear spacers contained in

the appliance to ensure escape of

heat generated during operation.

Proceed in the sequence

illustrated in figures.

Rehingeing the door

The side at which the door opens can be changed from the right side

(factory adjustment) to the left side, if the installation site requires.

Warning! When changing the side at which the door opens, the appliance

may not be connected to the mains. Remove plug from the mains

beforehand.

Procced as follows:

To carry out the following

operations, we suggest that this be

done with another person that will

keep a firm hold on the door of the

appliance during the operations.

Gently lay the appliance on its

back.

1. Remove the ventilation grille.

2. Remove the bottom hinge (A) by

unscrewing the fixing screws.

3. Remove the door.

4. Unscrew the pin of the bottom

hinge (f) and refit it on the

opposite side.

5. Unscrew the pin of the upper hinge

(d) and refit it on the opposite side.

6. Insert the door in the upper hinge

and refit the upper hinges (A).

Pay attention that the border of the

doors are parallel to the top border,

otherwise adjust the position of

the lower hinge of the door (A).

7. Remove from the ventilation

grille the cover (e) and refit it on

the opposite side.

8. Refit ventilation grille.

9. Unscrew the top handle bracket

from the handle rod (1). Unscrew

the bottom handle bracket from

the door (2).

Unscrew the top handle

bracket from the door (3) and

screw onto the bottom right-

hand side of the door (4).

Turn the handle bracket with

the handle rod 180° and screw

them to the door (5) and the

fitted handle bracket (6).

Move the small plug from right

to left..

Reposition, level the

appliance, wait for at least

one hour and then connect it

to the mains socket.

In any case you do not want to

carry out the above mentioned

operations, contact your local

Sales Service Force. The

Service engineer will carry

out the reversibility of the

doors at your cost.

Attention:

After having reversed the opening direction of the doors check that all the

screws are properly tightened and that the magnetic seal adheres to the

cabinet. If the ambient temperature is cold (i.e. in Winter), the gasket may

not fit perfectly to the cabinet. in that case, wait for the natural fitting of

the gasket or accelerate this process by heating up the part involved with a

normal hairdryer.

Electrical connection

Before initial start-up, refer to the appliance rating plate to ascertain if

supply voltage and current values correspond with those of the mains at the

installation location.

e.g.: AC 230 ... 240 V 50 Hz or

230 ... 240 V~ 50 Hz

(i.e. 230 to 240 volts alternating current, 50 Hertz)

The rating plate is inside the appliance on the left.

A correctly installed, earthed socket is required for the electrical supply. The

supply must have a fuse rating of at least 10 Amps.

If the socket is not accessible once the appliance is built in, the electrical

installation must include suitable means of isolating the appliance from the

mains (e.g. fuse, cut-out, current trip or similar with a minimum contact

separation of 3 mm).

Attention: it must be possible to disconnect the appliance from the mains

power supply; the plug must therefore be easily accessible after the

installation.

Attention: If the supply cord is damaged, it must be replaced by a special

cord or assembly available from the manufacturer or its Service Agent.

Prior to Initial Start–Up

• Please clean the appliance interior and all accessories prior to initial start-

up (see section: “Cleaning and Care”).

Control panel

A. Button ON/OFF

B. Temperature setting button (for warmer temperatures)

C. Temperature display

D. Temperature setting button (for colder temperatures)

E. COOLMATIC function and COOLMATIC indicator (yellow)

F ALARMOFF button and red warning light

Temperature setting buttons

The temperature is adjusted using the “B“ and “D“ buttons. These buttons

are connected to the temperature display.

• The temperature display is switched over from the display of the ACTUAL

temperature (Temperature display is illuminated) to the display of the

DESIRED temperature (Temperature display flashes) by pressing one of the

two buttons, “B“ or “D“ .

• Each time one of the two buttons is pressed again the DESIRED temperature

is adjusted by 1 °C. The DESIRED temperature must be reached within 24

hours.

If neither button is pressed, the temperature display automatically switches

back after a short period (approx. 5 sec.) to the display of the ACTUAL

temperature.

DESIRED temperature means:

The temperature that has been selected for inside the fridge. The DESIRED

temperature is indicated by flashing numbers.

ACTUAL temperature means:

The temperature display indicates the current temperature inside the fridge.

The ACTUAL temperature is indicated with illuminated numbers.

Temperature display

The temperature display can indicate several pieces of information.

• During normal operation, the temperature currently present in the fridge

(ACTUAL temperature) is displayed.

• When the temperature is being adjusted a flashing display indicates the

fridge temperature currently set (DESIRED temperature).

ALARM OFF button

With the ALARM OFF button, the acoustic warning signal can be switched

off, e.g. the "Open Door" warning when loading or rearranging food to be

chilled.

Starting Up - Setting the Temperature

1. Plug the mains plug into the mains socket.

2. Press button (A). The appliance starts.

3. Press either the “B“ or “D“ button. The temperature display switches over

and the DESIRED temperature currently set flashes on the temperature

display.

4. Set the required temperature by pressing the “B“ or “D“ buttons (see section

"Temperature setting buttons"). The temperature display will immediately

show the changed setting. Each time the button is pressed the temperature

is adjusted by 1 °C.

From a food safety point of view +5 °C should be considered sufficiently

cold for storing food in the fridge.

5. Once the required temperature has been set, after a short period (approx. 5

sec.) the temperature display will change and again indicate the current

ACTUAL temperature inside the fridge. The display will change from flashing

to continuous illumination.

Information! When the setting is changed, the compressor does not start

immediately if automatic defrosting is currently taking place. As the storage

temperature within the fridge is reached quickly you can store food

immediately after switching on.

COOLMATIC

The COOLMATIC function is suited for quick cooling of large quantities of

goods in the refrigerator.

1. The COOLMATIC function is switched on by pressing the COOLMATIC

button. The yellow light illuminates. The COOLMATIC function now provides

for intensive cooling. A DESIRED temperature of +2 °C is automatically

selected. The COOLMATIC function is ended automatically after a period of

6 hours.

2. The COOLMATIC function can be ended manually at any time by pressing

the COOLMATIC button again. The yellow light goes out.

QUICK CHILL

The quick chill function can be used for the fast cooling of drinks in cans or

bottles in the fast cool storage tray or of larger amounts of room-tempera

ture food. The built-in charcoal filter reduces the development of any smell.

Chilling of cans or bottles

Place cans or bottles in the holder

on the fast cool storage tray in front

of the fan grille. Turn the fan

regulator to maximum and press the

COOLMATIC button. The yellow

indicator light comes on.

Chilling of food

Place the food in the fridge.

Open the fan regulator to maximum and press the COOLMATIC button.

The yellow indicator light comes on.

When the drinks or the food is sufficiently cooled, press the COOLMATIC

button again. The yellow indicator light goes out. Set the fan regulator to

the minimum position.

MAX

MIN

"Open Door"- Warning

If the fridge door is left open for longer than 5 minutes the red warning

display will flash and an acoustic warning tone will sound.

If you need more time to load or rearrange refrigerated foods, you can

switch off the warning tone by pressing the ALARM OFF button. The red

warning display will go off when the door is closed.

Holiday Mode

In the holiday mode the temperature for the refrigerator is approximately

+15 °C. In the holiday mode it is therefore possible to leave the door of the

empty refrigerator closed during periods of extended absence. Advantage:

Unintentional, or accidental closing of the door by persons who have access

to your home during your absence, is no longer possible. Without activating

the holiday mode, leaving the door closed would lead to the accumulation

of odours and mould.

After emptying and cleaning the appliance, proceed as follows:

1. To set the holiday mode, press the “ +” (WARMER) or “-“ (COLDER) but-

ton. The temperature display will change and indicate in flashing numbers

the DESIRED temperature that is currently set.

2. Hold down the “+“ (WARMER) button until the temperature display

indicates H (for holiday). The temperature shown in the temperature display

will change in steps of 1 °C until it reaches +8 °C. After +8 °C the value +15

°C will appear in the display with the letter H. The fridge is now operating

in energy-saving holiday mode.

3 To switch the fridge back to normal operation, press the “-“ (COLDER)

button.

Important! Do not store any goods in the refrigerator when the holiday

mode is in operation. The temperature is regulated at about +15 °C when

the holiday mode is in operation. This is too warm for food products.

Warning: this appliance is sold in France.

In accordance with regulations

valid in this country it must be

provided with a special device (see

figure) placed in the lower

compartment of the fridge, to

indicate the coldest zone of it.

Interior Accessories

Storage shelves

• You should always slide one of the full size glass storage shelf into the

lowest set of guides, above the fruit and the vegetable containers, and

keep it in this position.

• The height of the storage shelves

can be adjusted:

• To do this pull the storage shelf

forward until it can be swivelled

upwards or downwards and

removed.

• Please do the same in reverse to

insert the shelf at a different

height. Slide the front half of the

shelf in another level to the rear. To

gain space to place tall items on

the storage shelf below.

Adjusting the upper door rack

Depending on the food stored, the upper door racks can be changed to

other holders or removed. Take out the food, press the door racks digonally

upwards at their edges, reposition them, and press them back into place.

D338

Bottle holder

Place the bottles (with the opening

facing front) in the pre- positioned

shelf.

If the shelf is positioned horizontally,

place only closed bottles.

This bottle holder shelf can be tilted

in order to store previously opened

bottles.

To do this, pull the shelf up so it can

rotate upwards and be placed on the

next higher level.

Quick Chill Shelf

The quick chill shelf can be placed

in the upper groove.

Bottle and Can Holder

The side of the bottle and can

holder is moveable to enable a more

flexible placement of cans and

bottles in front of the grid. To allow

the holder to be moved easier when

moving sideways, press the shelf

backwards.

The bottle support can be pulled out

when chilling larger bottles.

Dismantling of the Bottle and Can Holder

Take out the quick chill shelf with

holder from the cabinet.

To loosen the holder from the shelf,

bend the hooks/brackets that

surround the backside of the shelf.

Changing the carbon filter

To maintain the best performance

the carbon filter should be

changed once a year with normal

usage.

New carbon filters can be

purchased from your local dealer.

The filter is placed behind the grill

and can be

reached by opening the cover. The

cover can be opened by turning

the cover outward. The carbon

filter is pulled out of its slot.

The new carbon filter is placed in

the existing slot

The filter should be handled

carefully so fragments don´t

loosen from the surface.

Installation of the carbon filter

On delivery the carbon filter is

placed in a plastic bag to secure

the length of the carbon filter

life. The filter should be placed

behind the grill before the

cabinet is turned on.

The cover can be opened by

turning the cover outward. The

carbon filter is then mounted in

the slot found in the back, see the

illustration.

The filter should be handled

carefully so fragments don´t

loosen from the surface.

Fresh food refrigeration

To obtain the best performance:

• do not store warm food or evaporating liquid in the refrigerator

• do cover or wrap the food, particularly if it has a strong flavour.

• Position food so that air can circulate freely round it.

Useful hints:

Meat (all types): wrap in polythene bags and place on the glass shelf above

the vegetable drawer(s)For safety, store in this way only one or two days

at the most.

Cooked foods, cold dishes, etc: these should be covered and may be placed

on any shelf.

Fruit and vegetables: these should be thoroughly cleaned and placed in the

special drawer(s) provided.

Butter and cheese: these should be placed in special airtight containers or

wapped in aluminium foil or polythene bags to exclude as much air as

possible.

Milk bottles: these should have a cap and should be stored in the bottle

rack in the door.

Bananas, potatoes, onions and garlic, if not packed, must not be kept in

the refrigerator.

Defrosting

Refrigerator

Frost is automatically eliminated from the evaporator of the refrigerator

compartment every time the motor compressor stops, during normal use.

The defrost water drains out through a channel into a special container at

the back of the appliance, over the motor compressor, where it evaporates.

Switching off the appliance

1. To switch off, press the ON/OFF button. This will result in a countdown

from "3" to "1" taking place in the temperature display. On reaching "1" the

fridge will switch off. The temperature display will go off.

The appliance is only completely disconnected from the electricity supply

when the power plug has been removed from the power outlet.

Note:

The appliance cannot be switched on or off if unplugged, or if there is no

power being supplied to it.

Following connection to the mains power supply, the appliance returns to

the same operating state as before the interruption of main power.

If the appliance is not going to be used for an extended period:

1. Remove all refrigerated and deep-frozen packages as well as ice trays.

2. Switch off the appliance by pressing the ON/OFF button (A).

3. Remove the mains plug or switch off or turn out the circuit breaker or fuse.

4. Leave the door open to avoid the build up of odours.

Cleaning and Care

For hygienic reasons the appliance interior, including interior accessories,

should be cleaned regularly.

Warning!

• The appliance may not be connected to the mains during cleaning. Danger

of electrical shock! Before cleaning switch the appliance off and remove

the plug from the mains, or switch off or turn out the circuit breaker or

fuse.

• Never clean the appliance with a steam cleaner. Moisture could

accumulate in electrical components, danger of electrical shock! Hot

vapours can lead to the damage of plastic parts.

• The appliance must be dry before it is switched back on.

Attention!

• Ethereal oils and organic solvents can attack plastic parts, e.g.

– lemon juice or the juice from orange peals;

– butyric acid;

– cleansers which contain acetic acid.

Do not allow such substances to come into contact with appliance parts.

• Do not use any abrasive cleansers.

1. Remove the food from the refrigerator.

2. Switch the appliance off and remove the plug from the mains, or switch off

or turn out the circuit breaker or fuse.

3. Clean the appliance and the interior accessories with a cloth and lukewarm

water. Commercially available dish washing detergents may also be used.

4. After cleaning wipe with clean water and rub dry.

Accumulation of dust at the condenser increases energy consumption. For

this reason carefully clean the condenser at the back of the appliance once

a year with a soft brush or a vacuum cleaner.

5. Check the water drain hole on

the rear wall of the fridge. Clear a

blocked drain hole with the aid of

the green peg in the pack of

accessories included with the

appliance.

6. After everything is dry place

appliance back into service.

Energy Saving Tips

• Do not install the appliance near cookers, radiators or other sources of

warmth. High ambient temperatures cause longer, more frequent

operation of the compressor.

• Ensure sufficient air circulation and exhaust at the appliance base

and at the back wall of the appliance. Never cover air vent openings.

• Do not place warm foods into the appliance. Allow warm foods to cool

first.

• Only leave door open as long as necessary.

• Do not set temperature any colder than necessary.

• Put frozen food in the fridge to defrost. The cold in the frozen food will

then be used to cool the fridge.

• Keep the heat emitting condenser and the metal grille on the rear wall of

your appliance clean at all times.

D037

La page charge ...

Aeg-Electrolux S72398KA6 Manuel utilisateur

Marque: Aeg-Electrolux

Modèle: S72398KA6

Catégorie: Frigos

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Aeg-Electrolux S72398KA6 User manual

Aeg-Electrolux S72398KA6 Manuel utilisateur

Aeg-Electrolux S72398KA6 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents