Generac 3000 PSI 0064361 Manuel utilisateur

www.generac.com or 1-888-436-3722

Operator's Manual

OneWASH™ Power Washer

Introduction ............................................................. 1

Where to Find Us ...........................................................1

Safety Rules ........................................................... 1

Safety Symbols and Meanings .......................................1

General Information ................................................ 4

Know Your Power Washer .........................................................4

Product Specifications ..............................................................5

Emissions Information ..............................................................5

High Altitude Operation ..............................................................5

Unpacking .................................................................................5

Set-up ..................................................................... 6

Assembly ..................................................................................6

Add Engine Oil ..........................................................................7

Add Fuel ...................................................................................7

Connect Hose and Water Supply to Pump .................................8

How to Use Nozzles ..................................................................9

Operation .............................................................. 12

Operation ................................................................................12

Power Washer Location ..........................................................12

Checklist Before Starting Engine ..............................................12

How to Start Your Power Washer ............................................12

Automatic Cool Down System (Thermal Relief) .......................14

How to Stop Your Power Washer .............................................14

Maintenance ......................................................... 15

Maintenance Recommendations .............................................. 15

Maintenance Schedule ............................................................15

Alert System Maintenance ......................................................15

Pump Oil .................................................................................16

Emissions Control ................................................................... 16

Power Dial Settings .................................................................16

Power Washer Maintenance ....................................................16

Check and Clean Inlet Screen .................................................. 16

Check High Pressure Hoses ....................................................16

Check Detergent Siphoning Tube .............................................16

Check Spray Gun ....................................................................16

Chemical Tank Maintenance ....................................................16

Nozzle Maintenance ................................................................17

Engine Maintenance ................................................................17

Engine Oil Recommendations .................................................. 18

Service Air Cleaner .................................................................19

Service Spark Plug .................................................................. 19

Inspect Muffler and Spark Arrestor ..........................................20

After Each Use ........................................................................ 20

Winter Storage ........................................................................21

Long Term Storage..................................................................21

Other Storage Instructions ....................................................... 21

Transporting/Tipping of the Unit ..............................................21

Troubleshooting .................................................... 22

Troubleshooting Guide .............................................................22

Notes .................................................................... 23

MANUAL DEL OPERADOR ................................. 25

MANUEL DE L'UTILISATEUR ..................... 51

Table of Contents

WARNING!

California Proposition 65

Engine exhaust and some of its constituents are known to the state of California to cause cancer,

birth defects, and other reproductive harm.

WARNING!

California Proposition 65

This product contains or emits chemicals known to the state of California to cause cancer,

birth defects, and other reproductive harm.

INTRODUCTION

Thank you for purchasing this power washer manufactured by

Generac Power Systems, Inc. This model is a high performance,

air-cooled, engine-driven power washer that operates between

3000 and 3100 psi depending on which model you purchased.

The units feature custom designed wheels, axial cam pump

with stainless steel pistons, automatic cool down system, quick

connect nozzles, high pressure hose, detergent siphoning hose

and chemical tank.

Common sense and strict compliance with the special instructions

are essential to preventing accidents. The operator must read

this manual and thoroughly understand all of the instructions

and warnings before using the equipment. If any portion of the

manual is not understood, contact the nearest Authorized Dealer

for starting, operating and servicing procedures. The owner is

responsible for proper and safe use of the equipment.

The power washer can operate safely, efficiently and reliably only if

it is properly located, operated and maintained. Before operating,

servicing or storing:

• Study all warnings in this manual and on the product carefully.

• Become familiar with this manual and the unit before use.

• Refer to the Assembly section of the manual for instructions on

final assembly procedures. Follow the instructions completely.

The manufacturer cannot anticipate every possible circumstance

that might involve a hazard. The warnings in this manual, and on

tags and decals affixed to the unit are, therefore, not all inclusive. If

using a procedure, work method or operating technique that the

manufacturer does not specifically recommend, ensure that it is

safe for others. Also make sure the procedure, work method or

operating technique utilized does not render the power washer

unsafe.

THE INFORMATION CONTAINED HEREIN WAS BASED ON MACHINES

IN PRODUCTION AT THE TIME OF PUBLICATION. GENERAC

RESERVES THE RIGHT TO MODIFY THIS MANUAL AT ANY TIME.

Save these instructions for future reference. If you loan this

device to someone, ALWAYS loan these instructions AND the

Owner's Manual to the individual as well.

WHERE TO FIND US

You can contact Generac Customer Service by phone at 1-888-

436-3722, or on the internet at www.generac.com. Record the

important information of the unit in the following chart for future

reference and/or service inquiries.

Model Number

Serial Number

Date Purchased

SAFETY RULES

Throughout this publication, and on tags and decals affixed to

the power washer, DANGER, WARNING, CAUTION and NOTE

blocks are used to alert personnel to special instructions about

a particular operation that may be hazardous if performed

incorrectly or carelessly. Observe them carefully. Their definitions

are as follows:

Indicates a hazardous situation or action which, if not avoided,

will result in death or serious injury.

Indicates a hazardous situation or action which, if not avoided,

could result in death or serious injury.

Indicates a hazardous situation or action which, if not avoided,

could result in minor or moderate injury.

NOTE:

Notes contain additional information important to a procedure

and will be found within the regular text body of this manual.

These safety warnings cannot eliminate the hazards that they

indicate. Common sense and strict compliance with the special

instructions while performing the action or service are essential to

preventing accidents.

SAFETY SYMBOLS AND MEANINGS

KickbackToxic Fumes Electrical Shock

Fluid InjectionFall

Fire Explosion Operator’s Manual

Slippery Surface

Moving Parts Flying Objects Hot Surface

Hearing Protection

1

Introduction

2



DANGER: Carbon monoxide produced during use CAN KILL

in minutes. NEVER use indoors, in a vehicle, or in other

sheltered areas, EVEN IF doors and windows are open. Only

use OUTSIDE and far away from windows, doors and vents.

Some chemicals or detergents may be harmful if inhaled

or ingested, causing severe nausea, fainting, or poisoning.

• OperatepowerwasherONLYoutdoors.

• Arunningenginegivesoffcarbonmonoxide.

• Carbonmonoxideisanodorless,colorless,poisonousgas.

Breathing carbon monoxide can cause headache, fatigue,

dizziness, vomiting, confusion, seizures, nausea, fainting

or death. If you start experiencing any of these symptoms,

IMMEDIATELY move to fresh air. Seek medical attention.

• Keepexhaustgasfromenteringaconfinedareathrough

windows, doors, ventilation intakes, or other openings. Warn any

occupants inside about the symptoms of carbon monoxide so

they know to move to fresh air if they begin to feel ill.

• Theuseofacarbonmonoxidedetectorinsideanyoccupied

premises between the power washer and the occupant is

recommended.

• NEVERstartorrunengineindoors,inavehicle,orinan

enclosed area, EVEN IF windows and doors are open.

• Usearespiratorormaskwheneverthereisachancethat

harmful gas or vapors may be inhaled.

• Readallinstructionswithrespiratorormasksoyouarecertain

the respirator or mask will provide the necessary protection

against inhaling harmful gas or vapors. If you begin to

experience any of the CO symptoms listed above, IMMEDIATELY

move to fresh air.



DANGER: NEVER aim spray gun at people, animals, or

electrical devices. Serious injury or death will result.

ALWAYS point spray gun in safe direction, squeeze spray

gun trigger to release high pressure, every time you stop

engine. Engage trigger lock when not in use.

• Thehighpressurestreamofwaterthatthisequipment

produces can cut through skin and its underlying tissues,

leading to serious injury, possible amputation or death.

Spray gun traps high water pressure, EVEN WHEN engine

is stopped and water is disconnected, which can cause

injury.

• NEVERallowCHILDRENtooperatepowerwasherorplaynearby.

This is NOT a toy.

• NEVERrepairhighpressurehose.Replaceit.

• NEVERrepairleakingconnectionswithsealantofanykind.

Replace o-ring or seal.

• NEVERconnecthighpressurehosetonozzleextension.

• Keephighpressurehoseconnectedtopumpandspraygun

while system is pressurized.

• NEVERsecuresprayguninopenposition.

• NEVERleavespraygununattendedwhilemachineisrunning.

• NEVERuseaspraygunwhichdoesnothaveatriggerlockor

trigger guard in place and in working order.

• ALWAYS be certain spray gun, nozzles and accessories are

correctly attached.



WARNING: Risk of electrocution.

Contact with power source can cause electric shock or

burn.

• NEVERspraynearpowersource.



WARNING: Contact with muffler area can result in serious

burns. Exhaust heat/gases can ignite combustibles,

structures or damage fuel tank causing a fire.

• DONOTtouchhotpartsandAVOIDhotexhaustgases.

• Allowequipmenttocoolbeforetouching.

• Keepatleastfive(5)feet(152cm)ofclearanceonall

sides of power washer including overhead.

• ItisaviolationofCaliforniaPublicResourceCode,Section

4442, to use or operate the engine on any forest-covered,

brush-covered, or grass-covered land unless the exhaust

system is equipped with a spark arrester, as defined in

Section 4442, maintained in effective working order. Other

states or federal jurisdictions may have similar laws.

Contact the original equipment manufacturer, retailer, or dealer to

obtain a spark arrester designed for the exhaust system installed

on this engine.

• Replacementpartsmustbethesameandinstalledinthesame

position as the original parts.



WARNING: Fuel and its vapors are extremely flammable and

explosive. Fire or explosion can cause severe burns or death.

WHEN ADDING OR DRAINING FUEL

• TurnpowerwasherOFFandletitcoolatleasttwo(2)

minutes before removing fuel cap. Loosen cap slowly to

relieve pressure in tank.

• Fillordrainfueltankoutdoors.

• DONOToverfilltank.Allowspaceforfuelexpansion.

• Iffuelspills,waituntilitevaporatesbeforestarting

engine.

• Keepfuelawayfromsparks,openflames,pilotlights,heat,and

other ignition sources.

• DONOTlightacigaretteorsmoke.

WHEN STARTING EQUIPMENT

• Ensuresparkplug,muffler,fuelcap,andaircleanerareinplace.

• DONOTcrankenginewithsparkplugremoved.

WHEN OPERATING EQUIPMENT

• DONOTtipengineorequipmentatanglewhichcausesfuelto

spill.

• DONOTsprayflammableliquids.

WHEN TRANSPORTING OR REPAIRING EQUIPMENT

• Transport/repairwithfueltankEMPTY.

• Disconnectsparkplugwire.

WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN TANK

• Storeawayfromfurnaces,stoves,waterheaters,clothesdryers,

or other appliances that have pilot light or other ignition source

because they can ignite fuel vapors.

Safety Rules

3



WARNING: Hearing Protection Recommended.



WARNING: Use of power washer can create puddles and

slippery surfaces. Kickback from spray gun can cause you to

fall.

• Useonlyonalevelsurface.

• The cleaning area should have adequate slopes and

drainage to reduce the possibility of a fall due to slippery

surfaces.

• Donotuseonelevatedsurfaceswherechanceofkickback

could result in a serious fall.

• Firmlygraspspraygunwithbothhandswhenusinghigh

pressure spray to avoid injury when spray gun kicks back.



WARNING: Starter and other rotating parts can

entangle hands, hair, clothing, or accessories.

• NEVERoperatepowerwasherwithoutprotectivehousing

or covers.

• DONOTwearlooseclothing,jewelryoranythingthat

may be caught in the starter or other rotating parts.

• Tieuplonghairandremovejewelry.



WARNING: Starter cord kickback (rapid retraction) can result

in bodily injury. Kickback will pull hand and arm toward

engine faster than you can let go. Broken bones, fractures,

bruises, or sprains could result.

• NEVERpullstartercordwithoutfirstrelievingspraygun

pressure.

• Torelievetrappedpressure,pointguninsafedirectionand

release pressure by pulling/actuating trigger on spray gun.

• Whenstartingengine,pullcordslowlyuntilresistanceisfeltand

then pull rapidly to avoid kickback.

• Aftereachstartingattempt,whereenginefailstorun,always

point spray gun in safe direction, and squeeze spray gun trigger

to release high pressure.

• Firmlygraspspraygunwithbothhandswhenusinghigh

pressure spray to avoid injury when spray gun kicks back.



WARNING: Unintentional sparking can result in fire or electric

shock.

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR POWER

WASHER.

• Disconnectthesparkplugwirefromthesparkplugand

place the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Useapprovedsparkplugtester.

• DONOTcheckforsparkwithsparkplugremoved.



WARNING: Risk of eye injury. Spray can splash back or

propel objects.

• Alwayswearsafetygoggleswhenusingthisequipmentor

in vicinity of where equipment is in use.

• Beforestartingthepowerwasher,besureyouare

wearing adequate safety goggles.

• NEVERsubstitutesafetyglassesforsafetygoggles.

NOTE:

High pressure spray may damage fragile items including

glass.

• DO NOT point spray gun at glass when using red (0°) MAX

nozzle.

• NEVER aim spray gun at people, animals, electrical devices or

plants.

NOTE:

Improper treatment of power washer can damage it and

shorten its life.

• If you have questions about intended use, ask dealer or contact

qualified service center.

• NEVER operate units with broken or missing parts, or without

protective housing or covers.

• DO NOT by-pass any safety device on this machine.

• DO NOT operate power washer above rated pressure.

• DO NOT modify power washer in any way.

• Before starting power washer in cold weather, check all parts of

the equipment to be sure ice has not formed there.

• NEVER move machine by pulling on hoses. Use handle

provided on unit.

• Check fuel system for leaks or signs of deterioration, such as

chafed or spongy hose, loose or missing clamps, or damaged

tank or cap. Correct all defects before operating power washer.

• This equipment is designed to be used with Generac authorized

parts ONLY. If equipment is used with parts that DO NOT

comply with minimum specifications, user assumes all risks

and liabilities.

Safety Rules

4

KNOW YOUR POWER WASHER

Read this owner’s manual and safety rules before operating your

high power washer. If you loan this device to someone, ALWAYS

loan these instructions AND the owner’s manual to the individual

as well. Compare the illustrations with your high power washer to

familiarize yourself with the locations of various controls (Figure

1). Save this manual for future reference. Replacement owner’s

manuals can be printed from the Generac Web site.

A - Spray Gun – Controls the application of water onto the cleaning

surface with trigger device. Includes a trigger lock.

B - Lance with Quick Connect – Allows you to switch between different

nozzles.

C - High Pressure Hose – Connect one end to water pump and the other

to the spray gun.

D - Recoil Starter – Use for starting the engine.

E - Oil Fill – Check and add engine oil.

F - Air Filter – Protects engine by filtering dust and debris out of the

intake air.

G - Pump – Develops high pressure.

H - Thermal Relief Valve – Cycles water through the pump when water

reaches 125°F warm water will discharge from pump onto ground.

This prevents internal pump damage.

I - Engine On/Off Switch – Turn this switch to “ON” before using the

recoil starter. Turn the switch to “OFF” to stop the engine.

J - Unloader Valve – Controls the high pressure output.

K - High Pressure Outlet – Connection for high pressure hose.

L - Water Inlet – Connection for Garden Hose.

M - Fuel Tank – Fill tank with regular unleaded fuel. Always leave room

for fuel expansion.

O - Choke – Prepares a cold engine for starting.

P - Power Dial – Provides optimal cleaning power for each desired

application.

Q - Nozzles – Chemical injection, Blast (0°), Wash (25°), Detergent for

various high pressure cleaning applications.

R - Chemical Tank – A drain-able tank used to hold power washer safe

detergents to be siphoned into the low pressure stream.

S - Prepare/Start Instruction – Identifies proper procedure to set up

and start/stop power washer.

T - Drain Plug – Used to drain engine oil.

U - Serial Number Location

V - System Alert LED – The system will monitor the engine oil level and

the water supply pressure. The engine will shut down and a fault

indicator light will display on the control panel.

W - Chemical Tank Fill Cap

X - Chemical Tank Drain Cap

ITEMS NOT SHOWN

• Identification Label (on engine blower housing) – Provides model

and serial number of power washer. Please have these readily available

if calling for assistance.

• Detergent Siphoning Tube/Filter – Use to siphon power washer safe

detergents into the low pressure stream.

General Information

F

H

B

S

D

Q

U

P

V

I

R

A

X

W

O

C

J

K

L

H

T

E

G

M

Figure 1 – Features & Controls

5

General Information

PRODUCT SPECIFICATIONS

Pressure - (PSI / BAR) ..................... 3000/207 & 3100/213 Max

Flow Rate - (GPM / LPM) .......................................2.8/10.6 Max

Water supply temperature - (°F / C°) ........................100/38 Max

Hose length - (Feet / Meters) ...........................................30/9.1

Chemical Tank(s) - Number per unit ......................................... 1

Chemical Tank - Capacity (Gal) N/A .................................... 0.75

Nozzles - Number per unit ........................................................ 3

Lance Length (Inches / cm) .............................................. 20/51

Gun ..............................................................................Standard

Engine Displacement - (Cubic Inch / cc) ...................... 12.9/212

Spark Plug Type ............................................. F7TC or equivalent

Spark Plug Gap - (Inches / mm) ............ 0.028-0.031/0.70-0.80

Fuel Capacity - (Quarts / Liters) ...................................... 3.7/3.5

Oil Capacity - (Oz / Liters) ................................................20/0.6

Low Oil Shut Down System ..................................................Yes

Low Water Sensor Shut Down System .................................. Yes

On/Off Switch .......................................................................Yes

EMISSIONS INFORMATION

The U.S. Environmental Protection Agency (and California Air

Resource Board for equipment certified to CA standards) requires

that this engine comply with exhaust and evaporative emission

standards. Locate the emissions compliance decal on the engine

to determine what standards the engine meets, and to determine

which emissions warranty applies. The engine is certified to meet

the applicable emission standards on gasoline. It is important to

follow the maintenance specifications in the Maintenance section

to ensure that the engine complies with the applicable emission

standards for the duration of the product’s life. This engine utilizes

lean carburetion settings and other systems to reduce emissions.

Tampering with or altering the emission control system may

increase emissions and may be a violation of Federal or California

Law. Acts that constitute tampering include but are not limited to:

• Removal or alteration of any part of the intake, fuel, or exhaust

systems

• Altering or defeating the governor linkage or speed-adjusting

mechanism to cause the engine to operate outside its design

parameters

If you are aware of any of the following symptoms, have your

engine inspected and repaired by your servicing dealer:

• Hard starting or stalling after starting

• Rough idle

• Misfiring or backfiring under load

• Afterburning (backfiring)

• Black exhaust smoke or high fuel consumption

HIGH ALTITUDE OPERATION

The fuel system on this engine may be influenced by operation at

higher altitudes. Proper operation can be ensured by installing an

altitude kit when required. See the table below to determine when

an altitude kit is required. Operating this engine without the proper

altitude kit installed may increase the engine’s emissions and

decrease fuel economy and performance. Kits may be obtained

from any Dealer and should be installed by a qualified individual.

Altitude* Kit Number PSI

0 - 5000 Feet Not Required 3000/3100

5000 - 7000 Feet 0K2016 3000/3100

*Elevation above sea level.

NOTE:

If the altitude kit has been installed and the engine will be

operated at an altitude where the kit is not required, the

engine should be returned to the original factory configuration.

Operating the engine at lower altitudes with the kit installed

may cause the engine to overheat and result in serious engine

damage, and may result in decreased performance and

increased emissions.

UNPACKING

1. Remove the parts bag, accessories, and inserts included with

power washer.

2. Open carton completely by cutting each corner from top to

bottom.

3. Ensure you have all included items prior to assembly.

• MainUnit

• HandleAssembly

• HighPressureHose

• SiphonHose&Filter

• SprayGun

• LancewithQuickConnectFitting

• OilBottle

• HoseHookWireform

• PartsBag(whichincludesthefollowing):

– Operator’s Manual

– Warranty Statement

– Emission Warranty Statement

– CARB Emission Warranty Statement

– Owner’s Registration Card

– Bag containing Color-coded Nozzles

– 4mm Allen wrench

– Screw (Qty 4)

– Tree clips (Qty 4)

– Plastic Gun Holder

– Plastic Lance Holder

4. If you are missing any items from your carton, please call

Generac Customer Service at 1-888-436-3722. When calling

for assistance, please have the model and serial number from

the data tag available.

5. Fill out and send in registration card. Write Model number,

Serial number & date of purchase in the table located in the

"Where to Find Us" section.

6

Set-up

ASSEMBLY

Read entire operator’s manual before you attempt to assemble or if

you have any problems with the assembly of your power washer,

please call Generac Customer Service at 1-888-436-3722. When

calling for assistance, please have the model and serial number

from the data tag available.

1. Install gun hook to handle assembly using the (2) supplied tree

clips. Alien holes and push the tree clips into holes until they

sit flush with gun hook (Figure 2).

Figure 2 – Attach Gun Hook to Handle Assembly

2. Install lance hook to unit frame using (2) supplied tree clips.

Alien holes and push the tree clips into holes until they sit flush

with gun hook (Figure 3).

Figure 3 – Attach Lance Hook to Unit

3. Place handle assembly (A) onto cradle supports (B). Allow

handle to slide into position. Locate the (4) screws and allen

wrench. Install the four screws using supplied allen wrench as

shown in (Figure 4).

Figure 4 – Attach Handle to Unit

B

A

4. Install hose hook (Figure 5).

Figure 5 – Install Hose Hook

5. Insert color–colored nozzles in spaces provided in front panel

(Figure 6).

Figure 6 – Insert Nozzles

7

Set-up

6. Place spray gun/lance extension onto spray gun holder as

shown (Figure 7).

Figure 7 – Gun/Lance

7. Place recoil rope into holder as shown (Figure 8).

Figure 8 – Recoil Rope Hook

ADD ENGINE OIL

1. Place power washer on a flat, level surface.

2. Clean area around oil fill and remove orange oil fill cap/

dipstick.

3. Using oil funnel (optional), slowly pour oil into fill opening. See

Maintenance section for oil type recommendation.

NOTE:

On some units there is more than one oil fill location. In these

instances it is only necessary to use one of the oil fill points.

4. Check periodically until the oil level is between "L" and "H" on

the dipstick (Figure 9). DO NOT OVERFILL.

Figure 9 – Dipstick

Acceptable Oil

Level Range

NOTE:

Any attempt to crank or start the engine before it has been

properly serviced with the recommend oil may result in engine

failure.

5. Replace oil fill cap/dipstick and fully tighten.

ADD FUEL

Fuel must meet these requirements:

• Clean, fresh, unleaded gasoline.

• A minimum of 87 octane/87 AKI (91 RON).

• Gasoline with up to 10% ethanol (gasohol) is acceptable.

NOTE:

Avoid power washer damage. Failure to follow Operator’s

Manual for fuel recommendations voids warranty.

• DO NOT use unapproved gasoline such as E85.

• DO NOT mix oil in gasoline.

• DO NOT modify engine to run on alternate fuels.

To protect the fuel system from gelling, mix in a fuel stabilizer when

adding fuel. See Storage. All fuel is not the same. If you experience

starting or performance problems after using fuel, switch to a

different fuel provider or change brands.

Fuel and its vapors are extremely flammable

and explosive. Fire or explosion can cause

severe burns or death.

WHEN ADDING FUEL

• Turn powerwasherOFFandletitcool atleasttwo (2)minutes

before removing fuel cap. Loosen cap slowly to relieve pressure in

tank.

• Fillfueltankoutdoors.

• DONOToverfilltank.Allowspaceforfuelexpansion.

• Iffuelspills,waituntilitevaporatesbeforestartingengine.

• Keepfuelawayfromsparks,openflames,pilotlights,heat,and

other ignition sources.

• DONOTlightacigaretteorsmoke.

8

1. Clean area around fuel fill cap, remove cap.

2. Slowly add regular unleaded fuel to fuel tank. Be careful not

to overfill. Fill to bottom of filter screen, this will allow for fuel

expansion (Figure 10).

3. Install fuel cap and let any spilled fuel evaporate before

starting engine.

Figure 10 – Adding Fuel

CONNECT HOSE AND WATER SUPPLY TO PUMP

NOTE:

DO NOT run the pump without the water supply connected

and turned on. Damage to equipment resulting from failure to

follow this instruction will void warranty.

NOTE:

Remove and discard the shipping cap from the pump’s water

inlet before attaching hose.

1. Run water through your garden hose for 30 seconds to clean

out any debris.

2. Before connecting garden hose to water inlet, inspect inlet

screen (A) (Figure 11). Clean screen if it contains debris or

have it replaced if damaged. DO NOT run power washer if inlet

screen is damaged.

IMPORTANT: DO NOT siphon standing water for the water supply.

Use ONLY cold water (less than 100°F). Water supply must be

adequate to handle greater than 3.8 gallons per minute and no less

than 30 psi.

NOTE:

Using a One Way Valve (vacuum breaker or check valve) at

pump inlet can cause pump or inlet connector damage.

• There MUST be at least ten feet of unrestricted garden hose

between the power washer inlet and any device, such as a

vacuum breaker or check valve.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

Figure 11 – Inspect Inlet Screen

A

3. Connect the garden hose (not to exceed 50 feet in length) to

the water inlet (Figure 12). Tighten by hand.

Figure 12 – Connect Garden Hose

Risk of eye injury. Spray can splash back or propel

objects.

• Always wear safety goggles when using this equipment or in

vicinity of equipment in use.

• Before starting the power washer, be sure you are wearing

adequate safety goggles.

• NEVERsubstitutesafetyglassesforsafetygoggles.

Set-up

9

4. Connect lance to spray gun (Figure 13). Tighten by hand.

Figure 13 – Attach Lance

5. Attach end of high pressure hose to base of spray gun (Figure

14). Tighten by hand.

Figure 14 – Connect Hose to Spray Gun

The high pressure stream of water that this equipment

produces can cut through skin and its underlying

tissues, leading to serious injury and possible

amputation.

• NEVERconnecthighpressurehosetolance.

• Keephighpressurehoseconnectedtopumpandspraygunwhile

system is pressurized.

• Always be certain spray gun, nozzles and accessories are

correctly attached.

6. Connect high pressure hose to pump (uncoil hose before

connecting to pump or spray gun) (Figure 15). Tighten by

hand.



The hose can be damaged if it comes in contact with a

hot engine or muffler.

Figure 15 – Connect High Pressure Hose to Pump

7. Turn ON the water, squeeze the trigger to purge the pump

system of air (Figure 16).

Figure 16 – Squeeze Trigger

HOW TO USE NOZZLES

The quick–connect on the nozzle lance allows you to switch

between different nozzles. Nozzles can be changed while power

washer is running once spray gun trigger is locked in the safety

position. The nozzles vary the pressure and spray pattern.

• For most effective cleaning, keep nozzle from 8 to 24 inches (20

to 61 cm) away from cleaning surface.

• If you get nozzle too close, especially using a high pressure

nozzle (RED), you may damage surface being cleaned.

The high pressure stream of water that this equipment

produces can cut through skin and its underlying

tissues, leading to serious injury and possible

amputation.

• NEVERexchangenozzleswithoutthetriggerlockbeingengagedon

the spray gun.

• DONOTtwistnozzleswhilespraying.

Set-up

10

NOZZLE PSI GPM

Blast

3100 2.4

3000 2.4

Wash 2600 2.8

The OneWash power washer is equipped with a Power dial to

provide optimal cleaning power for each application (Figure 26).

1. Pull back collar on quick–connect lance (Figure 17) and install

the GREEN wash nozzle (Figure 18) for the following cleaning

applications.

Figure 17 – Nozzles

Figure 18 – Wash Pressure Nozzle (Green)

2. Turn the Power Dial so that it matches the material you would

like to clean (Figure 19).

Car icon - This setting is best for cleaning cars, boats

and RV’s as it delivers the right balance of power and

flow to clean these types of surfaces effectively.

House Icon - This setting is best for cleaning vinyl and

aluminum siding on your home, as it delivers the right

balance of power and flow to clean these types of

surfaces effectively.

Wood Fence Icon - This setting is best for cleaning

wood decks fences and siding on your home, as it

delivers the right balance of power and flow to clean

these types of surfaces effectively.

Brick Icon - This setting is best for cleaning brick,

concrete and masonry materials, as it delivers the right

balance of power and flow to clean these types of

surfaces effectively.

Figure 19 – Power Dial

DELICATE

2000 PSI

HEAVY DUTY

3100 PSI

LOW OIL

LOW WATER

PRESSURE CONTROL

3. To remove persistent stains on concrete or masonry surfaces,

use the red blast nozzle within the stained area (Figure 20).



This tip (Red Nozzle) can damage work surface if it is

too close or held in one position for an extended time.

Figure 20 – Blast Pressure Nozzle (Red)

• Whenapplyingdetergent,useonlytheblacknozzle(Figure21).

Only use power washer safe detergents/soaps to help break down

stubborn dirt and grime on a variety of surfaces.

Figure 21 – Detergent Nozzle (Black)

Set-up

11

CLEANING AND APPLYING DETERGENT



Chemicals can cause bodily injury, and/or property

damage.

• NEVERusecausticliquidwithpowerwasher.

•Use ONLY power washer safe detergents/soaps. Follow all

manufacturer's instructions.

To apply detergent, follow these steps:

1. Review use of nozzles

2. Remove chemical tank cap (Figure 22).

3. Prepare detergent solution as required by job.

Figure 22 – Chemical Tank & Cover

4. Insert filter on end of siphoning tube through the hole in the

chemical tank cap (Figure 23).

5. Make sure siphoning tube remains fully submerged into

detergent.

Figure 23 – Install Siphoning Tube

NOTE:

Make sure the filter remains fully submerged in detergent

while applying detergent.

NOTE:

Contact with the hot muffler can damage detergent siphoning

tube.

• Wheninsertingthesiphonintoadetergentsolutionbottle,routethe

tube so as to keep it from inadvertently contacting the hot muffler.

6. Make sure black detergent nozzle is installed.

NOTE:

Detergent cannot be applied with the high pressure nozzle

(Green or Red). Only use the Black nozzle with detergent.

7. Confirm set-up instructions have been followed.

NOTE:

You must attach all hoses before you start the engine.

• Startingtheenginewithoutallthehosesconnectedandwithoutthe

water turned ON will damage the pump.

• Damagetoequipmentresultingfromfailuretofollowthisinstruction

will void warranty.

8. Start engine following instructions How to Start Your Power

Washer.

9. Apply detergent to a dry surface, starting at lower portion

of area to be washed and work upward using long, even,

overlapping strokes.

10. Allow detergent to "soak in" for 3-5 minutes before washing

and rinsing. Reapply as needed to prevent surface from

drying. DO NOT allow detergent to dry on surface being

cleaned (prevents streaking).

IMPORTANT: You must flush the detergent siphoning system after

each use by placing the filter into a bucket of clean water, then run

the power washer in low pressure for 1-2 minutes.

POWER WASHER RINSING

1. Remove black detergent nozzle from lance.

2. Select and install desired high pressure nozzle following

instructions How to Use Nozzles.

3. Point spray gun in safe direction and away from people,

animals and plants. Squeeze trigger to flush any remaining

chemical from system.

4. Keep spray gun a safe distance from area you plan to spray.

Kickback from spray gun can cause you to fall.

• Useonlyonalevelsurface.

• Donotuseonelevatedsurfacetopreventtherisk

of a serious fall.

• Firmlygraspspraygunwithbothhandswhenusinghighpressure

spray to avoid injury when spray gun kicks back.

5. Apply a high pressure spray to a small area and then check

surface for damage. If no damage is found, you can assume

it is okay to continue rinsing.

6. Start at top of area to be rinsed, working down with same

overlapping strokes as you used for cleaning.

Operation

12

CLEANING DETERGENT SIPHONING TUBE

If you used the detergent siphoning tube, you must flush it with

clean water before stopping the engine.

1. Place detergent siphoning tube/filter in a bucket full of clean

water.

2. Remove high pressure nozzle from nozzle extension.

3. Select and install black detergent nozzle following instructions

How to Use Nozzles.

4. Flush for 1-2 minutes.

5. Shut off engine following instructions How to Stop Power

Washer and turn off water supply.

6. ALWAYS point spray gun in a safe direction, squeeze spray

gun trigger to release retained high water pressure. Engage

trigger lock when not in use.

IMPORTANT: Spray gun traps high water pressure, even when

engine is stopped and water is disconnected.

The high pressure stream of water that this equipment

produces can cut through skin and its underlying

tissues, leading to serious injury and possible

amputation. Spray gun traps high water pressure, even

when engine is stopped and water is disconnected,

which can cause injury.

• Keephighpressurehoseconnectedtopumpandspraygunwhile

system is pressurized.

• ALWAYS point spray gun in safe direction, and squeeze spray

gun trigger to release high pressure, every time you stop engine.

Engage trigger lock when not in use.

OPERATION

If you have any problems operating your power washer, please call

Generac customer service at 1-888-436-3722.

POWER WASHER LOCATION

Clearances and Air Movement

Running engine gives off carbon monoxide, an

odorless, colorless, poisonous gas. Breathing carbon

monoxide can cause headache, fatigue, dizziness,

vomiting, confusion, seizures, nausea, fainting or

death. For more information, reference the CO

warnings in the Safety Rules section.

Place power washer outdoors in an area that will not accumulate

deadly exhaust gas. NEVER place power washer where exhaust

gas could accumulate and enter inside or be drawn into a

potentially occupied building. Ensure exhaust gas is kept away

from any windows, doors, ventilation intakes, or other openings

that can allow exhaust gas to collect in a confined area. Prevailing

winds and air currents should be taken into consideration when

positioning power washer (Figure 24).

• OperatepowerwasherONLYoutdoors.

• Keepexhaustgasfromenteringaconfinedareathroughwindows,

doors, ventilation intakes, or other openings.

• NEVER start or run engine indoors, in a vehicle or in an enclosed

area, EVEN IF windows and doors are open.

Exhaust heat/gases can ignite combustibles,

structures or damage fuel tank causing a fire.

• Keepatleast5ft.(152cm)clearanceonallsidesofpowerwasher

including overhead.

Figure 24 – Building Clearances

5 Foot Minimum

CHECKLIST BEFORE STARTING ENGINE

1. Be sure to read and understand the Operator Safety section

and Operation section before using power washer.

2. Check that the oil is at the full mark on the dipstick, and that

fuel has been added to the fuel tank.

3. Review the unit's assembly and ensure fitting are properly

secured and make sure there are no kinks, cuts, or damage to

high pressure hose.

4. Provide a proper water supply at an adequate flow, clear

screens of debris, and confirm that the system is purged of air.

5. Confirm unit is secure on level ground and surrounding work

area is clear.

HOW TO START YOUR POWER WASHER

NOTE:

DO NOT run the pump without the water supply connected

and turned on. Damage to equipment resulting from failure to

follow this instruction will void warranty.

This pressure washer is equipped with a low oil (engine) and

low water pressure alert system to protect the unit from being

damaged. The system will monitor the engine oil level and the

water supply pressure.

Operation

13

If the engine oil level or the water supply pressure drops below the

minimum set value, the engine will shut down and a fault indicator

light will display on the control panel. The indicator light will display

one blink per/second for low oil level and 2 blinks per/second for

low water supply pressure. The fault light will continue to flash for

one minute. Once the fault is fixed you can restart the pressure

washer (Figure 25).

Figure 25 – System Alert LED

DELICATE

2000 PSI

HEAVY DUTY

3100 PSI

LOW OIL

LOW WATER

SYSTEM ALERT LED

NOTE:

Your pressure washer will not start without engine oil or the

water supply connected and turned on. If the engine does not

start look for the fault indicator light display on the control

panel.

NOTE:

Make sure the pressure washer is on level ground when in

use. Running the unit on an incline greater than 15º could

cause the low oil level fault and cause the engine to shut

down.

NOTE:

The fault indicator light will continue to blink for one minute

even though the fault has been fixed or until the unit is

restarted.

1. Turn the ON/OFF switch to the "ON" position (Figure 26).

Figure 26 – ON/OFF Switch

DELICATE

2000 PSI

HEAVY DUTY

3100 PSI

LOW OIL

LOW WATER

ON/OFF SWITCH

2. Rotate pressure control knob to the position shown on “Start”

decal (Item #2) (Figure 27).

Figure 27 – Power Dial

DELICATE

2000 PSI

HEAVY DUTY

3100 PSI

LOW OIL

LOW WATER

PRESSURE CONTROL

3. Choke the engine by slowly pulling out on the choke knob until

it stops in the “ON” position (Figure 28).



WARNING: Hearing Protection Recommended.

NOTE:

For a warm engine, push the choke knob down until it stops in

the “OFF” position (Figure 28).

Figure 28 – Choke Knob

DELICATE

2000 PSI

HEAVY DUTY

3100 PSI

LOW OIL

LOW WATER

CHOKE “ON”

CHOKE “OFF”

4. Secure unit from movement when pulling recoil.

Operation

14

5. When starting the engine, grasp starter grip handle (Figure

29) and pull slowly until you feel some resistance. Then pull

rapidly to start engine.

Figure 29 – Starting the Engine

STARTER

GRIP

6. Return starter grip handle slowly. DO NOT let rope “snap

back” against holder.

7. When engine starts, slowly push the choke knob in to the

“OFF” position as engine warms. If engine falters, pull choke

knob out to the “ON” position, then push in to the “OFF”

position (Figure 30).

Figure 30 – Choke Knob

8. After each starting attempt, where engine fails to run, always

point gun in safe direction, and squeeze spray gun trigger to

release high pressure.

9. If engine fails to start after six pulls, push choke knob in to the

“OFF” position, and repeat steps 6 through 10.

NOTE:

Your pressure washer will not start without engine oil or the

water supply connected and turned on. If the engine does not

start look for the fault indicator light display on the control

panel.

The high pressure stream of water that this equipment

produces can cut through skin and its underlying

tissues, leading to serious injury and possible

amputation. Spray gun traps high water pressure, even

when engine is stopped and water is disconnected,

which can cause injury.

• DONOTallowCHILDRENtooperatepowerwasherorplaynearby.

• Keephighpressurehoseconnectedtopumpandspraygunwhile

system is pressurized.

• NEVER aim spray gun at people, animals or electrical devices.

Serious injury will result.

• DONOTsecuresprayguninopenposition.

• DONOTleavespraygununattendedwhilemachineisrunning.

• NEVER use aspraygun which does not have a triggerlockor

trigger guard in place and in working order.

• Always be certain spray gun, nozzles and accessories are

correctly attached.

 Contact with muffler area can result in serious

burns. Exhaust heat/gases can ignite

combustibles, structures or damage fuel tank

causing a fire.

• DONOTtouchhotpartsandAVOIDhotexhaustgases.

• Allowequipmenttocoolbeforetouching.

• Keepatleast5feet(152cm)ofclearanceonallsidesofpower

washer including overhead.

• ItisaviolationofCaliforniaPublicResourceCode,Section4442,

to use or operate the engine on any forest-covered, brush-covered,

or grass-covered land unless the exhaust system is equipped with

a spark arrester, as defined in Section 4442, maintained in effective

working order. Other states or federal jurisdictions may have

similar laws.

• Replacementpartsmustbethesameandinstalled inthe same

position as the original parts.

AUTOMATIC COOL DOWN SYSTEM (THERMAL

RELIEF)

If you run the engine on your power washer for 3-5 minutes

without pressing the trigger on the spray gun, circulating water

in the pump can reach temperatures above 125°F. The system

engages to cool the pump by discharging the warm water onto

the ground.

HOW TO STOP YOUR POWER WASHER

1. Release spray gun trigger.

2. Turn the engine ON/OFF switch to the "OFF" position (Figure

31).

3. ALWAYS point spray gun in a safe direction, and squeeze

spray gun trigger to release retained high water pressure.

Engage trigger lock when not in use.

4. Turn OFF water supply.

Operation

15

Figure 31 – ON/OFF Switch

DELICATE

2000 PSI

HEAVY DUTY

3100 PSI

LOW OIL

LOW WATER

ON/OFF SWITCH

IMPORTANT: Spray gun traps high water pressure, even when

engine is stopped and water is disconnected.

The high pressure stream of water that this equipment

produces can cut through skin and its underlying

tissues, leading to serious injury and possible

amputation. Spray gun traps high water pressure, even

when engine is stopped and water is disconnected,

which can cause injury.

• Keephighpressurehoseconnectedtopumpandspraygunwhile

system is pressurized.

• ALWAYS point spray gun in safe direction, squeeze spray gun

trigger to release high pressure, every time you stop engine.

Engage trigger lock when not in use.

MAINTENANCE RECOMMENDATIONS

Regular maintenance will improve the performance and extend

the life of the power washer. See any qualified dealer for service.

The power washer’s warranty does not cover items that have been

subjected to operator abuse or negligence. To receive full value

from the warranty, the operator must maintain the power washer

as instructed in this manual, including proper storage as detailed

in Winter Storage and Long Term Storage.

NOTE:

Should you have questions about replacing components

on your power washer, please call 1-888-436-3722 for

assistance.

Some adjustments will need to be made periodically to properly

maintain your power washer.

All service and adjustments should be made at least once each

season. Follow the requirements in the Maintenance Schedule

chart.

NOTE:

Once a year you should clean or replace the spark plug, clean

or replace the air filter, and check the spray gun and nozzle

extension assembly for wear. A new spark plug and clean air

filter assure proper fuel-air mixture and help your engine run

better and last longer.

MAINTENANCE SCHEDULE

Follow the hourly or calendar intervals, whichever occurs first.

More frequent service is required when operating in adverse

conditions.

First 5 Hours

Change engine oil

Every 8 Hours or Daily

Check/clean water inlet screen*

Check high pressure hose

Check detergent siphoning hose/filter

Check spray gun and assembly for leaks

Clean debris

Check engine oil level

Every 20 Hours or Every Season

Change engine oil**

Every 50 Hours or Every Season

Check/clean air cleaner filter**

Inspect muffler and spark arrester*

Every 100 Hours or Every Season

Service spark plug

* Clean if clogged. Replace if perforated or torn.

** Service more often under dirty or dusty conditions.

ALERT SYSTEM MAINTENANCE

Your alert system is powered by a CR2032 battery. The battery

must be replaced if the indicator light does not work. The fault

indicator light will flash once when recoil rope is pulled to start

your unit. If the fault indicator light remains on and steady the

battery needs to be replaced.

1. Locate the circuit board on back of the control panel (Figure

32).

Figure 32 – Circuit Board

Billboard

Circuit Board

Screw

(NOT SUPPLIED)

2. Remove the 2 mounting screws.

3. Remove circuit board from control panel making sure not to

damage the foam seal.

Maintenance

16

4. Remove battery (CR2032) and replace with new one. Make

sure battery is installed correctly (Figure 33).

Figure 33 – Battery Replacement

Replace Battery

5. Reinstall circuit board in reverse order. DO NOT OVER

TIGHTEN SCREWS.

PUMP OIL

DO NOT attempt any oil maintenance on this pump. The pump is

pre-lubricated and sealed from the factory, requiring no additional

maintenance for the life of the pump.

EMISSIONS CONTROL

Maintenance, replacement, or repair of the emissions control

devices and systems may be performed by any non-road engine

repair establishment or individual. However, to obtain ”no

charge” emissions control service, the work must be performed by

a factory authorized dealer. See the Emissions Warranty.

POWER DIAL SETTINGS

Tampering, maintenance, adjustment or replacement of the throttle

settings will impact the performance and may void the warranty

of the unit.

POWER WASHER MAINTENANCE

Clean Debris

Daily or before use, clean accumulated debris from cleaning

system. Keep linkage, spring and controls clean. Keep area

around and behind muffler free from any combustible debris.

Inspect cooling air slots and openings on the power washer. These

openings must be kept clean and unobstructed.

Power washer parts should be kept clean to reduce the risk of

overheating and ignition of accumulated debris.

• Use a damp cloth to wipe exterior surfaces clean.

NOTE:

Improper treatment of power washer can damage it and

shorten its life.

• DO NOT insert any objects through cooling slots.

• Use a soft bristle brush to loosen caked on dirt, oil, etc.

• Use a vacuum cleaner to pick up loose dirt and debris.

CHECK AND CLEAN INLET SCREEN

Examine the screen on the pump’s water inlet. Clean it if the screen

is clogged or replace it if screen is damaged.

CHECK HIGH PRESSURE HOSES

The high pressure hoses can develop leaks from wear, kinking, or

abuse. Inspect the hoses each time before using them. Check for

cuts, leaks, abrasions or bulging of cover, damage or movement

of couplings. If any of these conditions exist, replace the hose

immediately.

The high pressure stream of water that this equipment

produces can cut through skin and its underlying

tissues, leading to serious injury and possible

amputation.

• NEVERrepairhighpressurehose.Replaceit.

• ReplacementhoseratingMUSTmeetorexceedmaximumpressure

rating of unit.

CHECK DETERGENT SIPHONING TUBE

Examine the filter on the detergent tube and clean if clogged. The

tube should fit tightly on the barbed fitting. Examine the tube for

leaks or tears. Replace the filter or tube if either is damaged.

CHECK SPRAY GUN

Examine the hose connection to the spray gun and make sure it

is secure. Test the trigger by pressing the trigger, it “springs back”

into place when you release it. Replace spray gun immediately if it

fails to "spring back".

CHEMICAL TANK MAINTENANCE

Periodically you will need to drain and clean the chemical tank.

Use the following these instructions:

1. Shut off engine and turn off water supply.

2. ALWAYS point spray gun in a safe direction, squeeze spray

gun trigger to release retained high water pressure.

3. Remove chemical fill cap and siphon hose (Figure 34).

4. Obtain a container to drain the excess chemical into.

Maintenance

17

Figure 34 – Chemical Cap/Siphon Hose

5. Place container under the chemical tank drain. (Figure 35).

6. Remove drain cap and allow chemical to drain.

7. Insert garden hose into fill neck allow water to flush out tank.

8. Once tank is clean re install drain cap with gasket, do not over

tighten.

Figure 35 – Chemical Drain Cap

NOZZLE MAINTENANCE

A pulsing sensation felt while squeezing the spray gun trigger

may be caused by excessive pump pressure. The principal cause

of excessive pump pressure is a nozzle clogged or restricted

with foreign materials, such as dirt, etc. To correct the problem,

immediately clean the nozzle following these instructions:

1. Shut off engine and turn off water supply.

2. ALWAYS point spray gun in a safe direction, squeeze spray

gun trigger to release retained high water pressure.

The high pressure stream of water that this equipment

produces can cut through skin and its underlying

tissues, leading to serious injury and possible

amputation. Spray gun traps high water pressure, even

when engine is stopped and water is disconnected,

which can cause injury.

• Keephighpressurehoseconnectedtopumpandspraygunwhile

system is pressurized.

• ALWAYSpointsprayguninsafedirection,andsqueezespraygun

trigger to release high pressure every time you stop engine. Engage

trigger lock when not in use.

3. Remove nozzle from end of nozzle extension.

4. Use a small paper clip to free any foreign material clogging or

restricting nozzle (Figure 36).

5. Remove lance from spray gun.

Figure 36 – Free Foreign Material

6. Using a garden hose, remove additional debris by back

flushing water through lance (Figure 37). Back flush between

30 to 60 seconds.

Figure 37 – Back Flush Lance

7. Reinstall nozzle into lance.

8. Reconnect lance to spray gun.

9. Make sure garden hose is connected to pump water inlet.

Check that high pressure hose is connected to spray gun and

pump. Turn on water.

10. Start engine following instructions How to Start Your Power

Washer.

11. Test power washer by operating with each quick connect

nozzle.

ENGINE MAINTENANCE

 Unintentional sparking can result in fire or

electric shock.

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR POWER

WASHER

• Disconnectthesparkplugwirefromthesparkplugandplacethe

wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

•Useapprovedsparkplugtester.

•DONOTcheckforsparkwithsparkplugremoved.

Maintenance

18

ENGINE OIL RECOMMENDATIONS

We recommend the use of high-quality detergent oils acceptable if

classified for service SF, SG, SH, SJ or higher. DO NOT use special

additives.

Outdoor temperatures determine the proper oil viscosity for the

engine. Use the chart to select the best viscosity for the outdoor

temperature range expected.

SAE 30*

10W-30**

5W-30

* Below 50°F (10°C) the use of SAE 30 will result in hard starting.

** Above 80°F (27°C) the use of 10W30 may cause increased oil consumption.

Check oil level more frequently.

NOTE:

Synthetic oil meeting ILSAC GF-2, API certification mark

and API service symbol with “SJ/CF ENERGY CONSERVING”

or higher, is an acceptable oil at all temperatures. Use of

synthetic oil does not alter required oil change intervals.

NOTE:

The engine is equipped with an "Oil Alert System". This

system will automatically stop the engine before the oil level

falls below a safe limit. To avoid the inconvenience of an

unexpected shutdown, always check the engine oil level before

startup and ensure that the unit is not on an incline greater

than 15°.

CHECK OIL LEVEL

Oil level should be checked prior to each use or at least every 8

hours of operation. Keep oil level maintained.

1. Make sure power washer is on a flat, level surface.

2. Clean area around oil fill and wipe dipstick clean remove oil fill

cap (Figure 38).

3. Verify oil is at the proper level on the dipstick.

4. Insert the dipstick into filler neck but do not screw it in.

5. Replace and tighten oil fill cap.

Figure 38 – Fill Engine Oil

ADDING ENGINE OIL

1. Make sure power washer is on a flat, level surface.

2. Check oil level as described in Checking Oil Level.

3. If needed, slowly pour oil into oil fill opening until the proper

level on the dipstick is reached.

4. Insert the dipstick into filler neck but do not screw it in.

5. If level is low, fill until the oil level is between "L" and "H" on

the dipstick (Figure 39).

6. Replace and tighten oil fill cap.

Figure 39 – Dipstick

Acceptable Oil

Level Range

CHANGING ENGINE OIL

If you are using your power washer under extremely dirty or dusty

conditions, or in extremely hot weather, change the oil more often.



Avoid prolonged or repeated skin contact with used

motor oil.

• Usedmotoroilhasbeenshowntocauseskincancerincertain

laboratory animals.

• Thoroughlywashexposedareaswithsoapandwater.

Maintenance

La page est en cours de chargement...

Generac 3000 PSI 0064361 Manuel utilisateur

Generac 3000 PSI 0064361 Manuel utilisateur

dans d''autres langues

Documents connexes