OttLite CSAQC00P Mode d'emploi

Taper
Mode d'emploi
CONGRATULATIONS!
You’ve purchased the finest in natural lighting technology with your new OttLite® product.
PRODUCT REGISTRATION FORM
Please complete the enclosed Product Registration Form and return it today by mail, or
register online by going to: OttLite.com/warranty
WARNING: To prevent electric shock, make sure the lamp is not plugged in until all
steps are complete.
NOTE: THIS UNIT IS FULLY ASSEMBLED
1.
Remove lamp from packing, placing lamp body base (A) flat on a steady surface.
2.
Connect power adapter input (H) into connector (J) in the rear-bottom of the lamp.
3. Plug the power adapter (L) into a standard household 120V AC outlet. Note: Only
use with the supplied power adapter to avoid damage or fire.
4. Turn the lamp ON & OFF using power switch (B) located in the front-upper side of
base (A). Power switch (B) is a “touch” switch that controls ON/OFF power, the LED
brightness settings and the color mode function of the lamp.
5.
To power LED settings, slightly touch the switch to achieve the following:
• Turn lamp “ON” to 1st lower-brightness; touch the switch “once”;
• for medium-brightness; touch the switch “twice”;
• for high-brightness; touch the switch “three-times”;
• to turn lamp “OFF”; touch the switch “four-times”.
6. This lamp provides three color modes. To adjust lighting color mode slightly “press
and hold” switch (B) for three seconds to switch light color temperature mode;
5000°K, 2700°K, 4000°K.
7. Wireless charger for Qi-certified devices (C) is located in the center of base (A). See
Wireless Charging Instructions section for details.
8.
To position the shade simply bend the flex-neck (E) as needed to point the light. Please
hold the lamp base (A) while adjusting the lamp.
WIRELESS CHARGING INSTRUCTIONS:
Wireless charging requires a Qi-certified device. To determine if your device is
Qi-certified, please visit the Wireless Power Consortium website.
To wirelessly charge a device, perform the following:
• Place the device, which supports Qi wireless charging standard, face up on the
middle of the Qi wireless charging emblem (C).
• When the device is centered on the Qi wireless charging icon (C), a solid RED
light (D) will indicate the device is charging properly. NOTE: If RED light is
blinking, this indicates the device is not charging and needs to be properly centered.
• Check the charge level on your device periodically to determine when device is
fully charged. NOTE: Lamp DOES NOT provide any indication of when device is
fully charged.
CAUTION!
DEVICE MAY BECOME WARM DURING CHARGING. THIS IS NORMAL
AND PART OF THE PROCESS. CHARGING TIMES VARY BY DEVICE.
SAFETY WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,
OR INJURY TO PERSONS
1. Turn lamp off and WAIT UNTIL LAMP HEAD (F) IS COOL before handling.
2. The LED panel (G) might get hot after several hours of continuous use DO NOT
place your hands directly on LED light panel.
3. Never use with an extension cord unless the plug can be fully inserted into the
receptacles in the extension cord.
4. Do not alter the plug.
5. The lamp head included with this unit cannot be replaced by the consumer.
6. INDOOR USE ONLY.
NOTE: The important safety instructions appearing in this instruction sheet are not meant
to cover all possible conditions and situations that may occur. It must be understood that
common sense, caution, and care must be used with any electrical product.
CAUTION!
IF THE EXTERNAL FLEXIBLE CABLE OR CORD OF THIS LUMINAIRE IS
DAMAGED, IT SHALL BE EXCLUSIVELY REPLACED BY THE MANUFACTURER OR ITS SERVICE
AGENT OR A SIMILAR QUALIFIED PERSON IN ORDER TO AVOID A HAZARD. INDOOR USE ONLY.
CAUTION!
THE LIGHT SOURCE OF THIS LUMINAIRE IS NOT REPLACEABLE; WHEN
THE LIGHT SOURCE REACHES ITS END OF LIFE THE WHOLE LUMINAIRE SHALL BE REPLACED.
CAUTION: Any change or modification to product not expressly recognized by
OttLite Technologies voids OttLite’s responsibility for proper function of product.
FCC PART 15
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that the
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void the users authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
FCC/IC RF RADIATION EXPOSURE STATEMENT CAUTION:
To maintain compliance with the FCC’s RF exposure guidelines, place the product at least
20cm from nearby persons.
IC CANADA
This device contains licence-exempt transmitter(s)/receiver that comply with
Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause
undesired operation of the device.
Lémetteur/récepteur exempt de licence contenu dans le présent appareil est
conforme aux CNR d’Innovation, Sciences et Développement économique Canada
applicables aux appareils radio exempts de licence. Lexploitation est autorisée aux
deux conditions suivantes :
1. Lappareil ne doit pas produire de brouillage;
2. Lappareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d’en compromettre le fonctionnement.
CAN RSS-216/CNR-216
CAN ICES-005 (B)/NMB-005 (B)
POWER ADAPTER SPECIFICATION:
Input: AC 100-240V, 50/60 Hz, 1.3A
Output: 12V DC, 2500mA with a Male DC Plug
Qi CHARGER SPECIFICATION:
Output: 5V, 1A or up to 5 watts
THIS LAMP CONTAINS a 5V, 2,1A USB output port (K) located on the bottom rear of
lamp. USB port can charge items such as tablets, cellular phones, etc.
The “Qi” symbol is a trademark of the Wireless Power Consortium
ENGLISH LED Desk Lamp with Wireless Charging
A
C
LED Desk Lamp with Wireless Charging
CSAQC00P Q3QAFS
INS190547 REV120619
G
B
D
L
J
K
F
E
H
POWERED BY
  • Page 1 1

OttLite CSAQC00P Mode d'emploi

Taper
Mode d'emploi

dans d''autres langues