ENGLISH LED Desk Organizer Lamp with Wireless Charging Stand
LED Desk Organizer Lamp with Wireless Charging Stand
CS7QI00Z 1653261 Model: W22FS
INS220714 REV050322
L
CONGRATULATIONS! You’ve purchased the finest in natural lighting technology with your new
OttLite® product.
PRODUCT REGISTRATION FORM
Please complete the enclosed Product Registration Form and return it today by mail, or
register online by going to: OttLite.com/warranty
WARNING: To prevent electric shock, make sure the lamp is not plugged in until all steps
are complete.
NOTE: THIS UNIT IS FULLY ASSEMBLED
1.
Remove lamp from packing, placing lamp body base (A) flat on a steady surface.
2.
Connect power adapter input (B) into connector (C) in the rear-bottom of the lamp.
3. Plug the power adapter (D) into a standard household 120V outlet. Note: Only use with
the supplied power adapter to avoid damage or fire.
4. Power switch (E) is a “touch” switch that controls ON/OFF power, the LED brightness
settings and the color mode function of the lamp.
5.
To power the light, slightly touch the switch (E) to achieve the following:
• Turn lamp “ON” to 1st brightness setting; touch the switch “once”;
• for 2nd brightness setting; touch the switch “two-times”;
• for 3rd brightness setting; touch the switch “three-times”;
• to turn lamp “OFF”; touch the switch “four-times”.
6. This lamp provides three color modes. To adjust lighting color mode slightly “press and
hold” switch (E) for three seconds to switch light color temperature mode; 2700°K,
4000°K, 5000°K.
7. To reposition the light, hold the lamp base (A) steady and grasp either flex-neck (F) or
shade (G) depending on needed adjustment. DO NOT FORCE the shade or lamp body
outside allowable adjustable range as excessive adjustment may cause damage.
WIRELESS CHARGING INSTRUCTIONS:
Wireless charging requires a Qi-certified device. To determine if your device is
Qi-certified, please visit the Wireless Power Consortium website.
To wirelessly charge a device, perform the following:
• Place the device on the stand horizontally, face-up, and flat against the middle of the Qi
wireless charging icon (H). NOTE: Device will only charge when placed in the horizontal
positon.
• When the device is centered on the Qi wireless charging icon (H), a solid RED light (J)
will come ON noting charging mode active. NOTE: If RED light is OFF this indicates the
device is not charging. Your device should show charging is taking place.
• Check charge level on your device periodically to determine when device is fully charged.
NOTE: Product DOES NOT provide any indication of when device is fully charged.
CAUTION! Device may become warm during charging. This is normal and part of the
process. Charging times vary by device.
THIS LAMP CONTAINS a 5V, 2.1A USB output port (K) located on the bottom rear of lamp.
USB port can charge items such as tablets, cellular phones, etc.
SAFETY WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,
OR INJURY TO PERSONS
1. Turn lamp off and WAIT UNTIL LAMP HEAD (G) IS COOL before handling.
2. The LED panel (L) might get hot after several hours of continuous use DO NOT place your
hands directly on LED light panel.
3. Never use with an extension cord unless the plug can be fully inserted into the
receptacles in the extension cord.
4. Do not alter the plug.
5. The lamp head included with this unit cannot be replaced by the consumer.
6. INDOOR USE ONLY.
NOTE: The important safety instructions appearing in this instruction sheet are not meant
to cover all possible conditions and situations that may occur. It must be understood that
common sense, caution, and care must be used with any electrical product.
CAUTION!
IF THE EXTERNAL FLEXIBLE CABLE OR CORD OF THIS LUMINAIRE IS
DAMAGED, IT SHALL BE EXCLUSIVELY REPLACED BY THE MANUFACTURER OR ITS SERVICE
AGENT OR A SIMILAR QUALIFIED PERSON IN ORDER TO AVOID A HAZARD.
CAUTION!
THE LIGHT SOURCE OF THIS LUMINAIRE IS NOT REPLACEABLE; WHEN
THE LIGHT SOURCE REACHES ITS END OF LIFE THE WHOLE LUMINAIRE SHALL BE REPLACED.
FCC PART 15
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that the interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that of the receiver.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
FCC/IC RF RADIATION EXPOSURE STATEMENT CAUTION:
To maintain compliance with the FCC’s RF exposure guidelines, place the product at least 20cm
from nearby persons.
To maintain compliance with the IC RF exposure guidelines,place the product at least 10cm
from nearby persons.
Pour maintenir la conformité aux directives d’exposition RF de la FCC, placer le produit
à au moins 20 cm des personnes à proximité.
Pour maintenir la conformité aux directives d’exposition IC RF, placer le produit à au moins
10 cm des personnes à proximité.
IC CANADA
This device contains licence-exempt transmitter(s)/receiver that comply with Innovation,
Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject
to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause
undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est
conforme aux CNR d’Innovation, Sciences et Développement économique Canada
applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux
deux conditions suivantes :
1. L’appareil ne doit pas produire de brouillage;
2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d’en compromettre le fonctionnement.
CAN RSS-216/CNR-216
CAN ICES-005 (B)/NMB-005 (B)
CAUTION: Any change or modification to product not expressly recognized by OttLite
Technologies voids OttLite’s responsibility for proper function of product.
POWER ADAPTER SPECIFICATION:
Input: 100-240 V~, 50/60 Hz, 0.9A
Output: 12V 2.5A with a Male DC Plug
Qi CHARGER SPECIFICATION:
Output: 5V 1A
The “Qi” symbol is a trademark of the Wireless Power Consortium. All phones with
integrated wireless charging support “Qi”.
J
K
F
E
A
C
B
H
D
Read instructions
prior to use.
G
-
1
dans d''autres langues
- English: OttLite CS7QI00Z User manual
Documents connexes
-
OttLite CS3QN4WW Mode d'emploi
-
-
-
-
-
-
-
OttLite SCDQCWGS-WA Manuel utilisateur
-
-
