Sharper Image 1015473 Manuel utilisateur

Taper
Manuel utilisateur
WIRELESS VALET
DESK ORGANIZER WITH CHARGING PAD
SHARPER IMAGE® NAME AND LOGOS (INCLUDING
THE 77 LOGO AND TOMORROW’S TOMORROW)
ARE TRADEMARKS OR REGISTERED TRADEMARKS.
DISTRIBUTED BY AND © 2022 MERCHSOURCE, LLC.
IRVINE, CA 92618. ALL RIGHTS RESERVED.
FOR CUSTOMER SUPPORT, PLEASE CALL
1-800-374-2744.
Printed in China.
Featuring Qi technology for fast charging and
modular storage, the Wireless Valet helps you
organize accessories and personal items while
offering the convenience of cord-free charging on
the go.
Please read all instructions and warnings prior to
use.
Keep this manual as it contains important
information for future reference.
THANK YOU FOR PURCHASING
YOUR WIRELESS VALET.
WIRELESS CHARGING
Plug the USB-C power cable (included) into the input port in
the Wireless Valet lid.
Plug the other end of the cable into a USB-A power adapter
(not included) and then plug the adapter into a wall outlet.
Place your Qi enabled device on the lid, aligned with the
Sharper Image logo. The LED will turn on when charging.
MODULAR STORAGE
Fill the card holder with small items, business cards and more.
Snap the card holder into the underside of the Wireless Valet
lid.
Position the modular storage trays inside the storage
compartment as desired or remove for easy organization on
any desk or table.
Store the USB-C power cable (included) and your power
adapter (not included) in the Wireless Valet for use on the go.
CONTENTS
a. Wireless Valet organizer
b. Removable card holder
c. Magnetic lid with 10W Qi charging pad
d. Modular storage trays (x2)
e. USB-C to USB-A power cable
TECHNICAL SPECIFICATIONS
• Item Number: 1015473
• Wireless Output: 10W
• USB-C Input: 5V/2A, 9V/2A, 12V/1.5A
• Charger Indicator: White LED Indicator
• Dimensions: 7.91 in. x 6.20 in. x 2.05 in.
(200 mm x 157 mm x 52 mm)
• Weight: 512g (1.13lb)
The Wireless Valet is designed to provide optimal
charging at up to 10W.
Certified charging for Qi-enabled devices, including but
not limited to:
iPhone series 8, X, 11, SE (2nd and 3rd generations), 12,
and 13
SAFETY WARNINGS
PLEASE READ BEFORE USE
• Not a children’s item. Keep out of reach of children.
• Do not use this item near people with pacemakers or similar medical
devices.
• Do not expose to moisture or extreme temperatures.
• Only use the provided charging cable.
• Use this item only for its intended purpose.
• Do not expose to extreme temperatures or moisture.
• For indoor use only.
• Do not expose to direct sunlight for extended periods of time.
• Thoroughly inspect products before every use. If the product appears
worn, frayed/splintered, cracked, or broken in any manner,
discontinue use and discard immediately.
This device contains licence-exempt transmitter(s)/receiver(s) that
comply with Innovation, Science and Economic Development Canada’s
licence-exempt RSS(s). Operation is subject to the following two
conditions:
1This device may not cause interference.
2This device must accept any interference, including interference that
may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent
appareil est conforme aux CNR d’Innovation, Sciences et
Développement économique Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes :
1L’appareil ne doit pas produire de brouillage;
2L’appareil doit accepter tout brouillage radioélectrique subi, même si
le brouillage est susceptible d’en compromettre le fonctionnement.
IC: 21808-1015473
a.
b.
e.
c.
d.
FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications to this unit not expressly approved
by the party responsible for compliance could void the user’s authority
to operate the equipment.
To maintain compliance with the RF exposure guidelines, place the
product at least 20cm from nearby persons.
Pour rester en conformité avec les consignes d'exposition aux RF,
placez le produit à au moins 20 cm des personnes proches.
FCC ID: 2AEVM1015473
  • Page 1 1
  • Page 2 2

Sharper Image 1015473 Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues