Spigen PF2009 Manuel utilisateur

Marque: Spigen

Modèle: PF2009

Taper: Manuel utilisateur

Instruction

US Cautions

Note

FCC Part 15 Compliance ISED Regulatory Compliance

User Manual

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference,

and (2) this device

must accept any interference received, including

interference that may cause undesired operation.

•CAUTION: Changes or modiﬁcations not expressly

approved by the party responsible for compliance

could void the user’s authority to operate the product.

•Note: This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications. However, there is no guarantee that

interference will not occur in a particular installation. If

this equipment does cause harmful interference to

radio or television reception, which can be determined by

turning the equipment o and on, the user is encouraged

to try to correct the interference by one or more of the

following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment

and receiver.

- Connect the equipment into an outlet on a circuit

dierent from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV

technician for help.

This equipment complies with FCC radiation exposure

limits set forth for an uncontrolled environment. This

equipment should be installed and operated with

minimum distance 20cm between the radiator and

your body. This transmitter must not be co-located

or operating in conjunction with any other antenna

or transmitter.

This device contains licence-exempt transmitter(s)/receiv-

er(s) that comply with Innovation, Science and Economic

Development Canada’s licence-exempt RSS(s).

Operation is subject to the following two conditions:

1. This device may not cause interference.

2. This device must accept any interference, including

interference that may cause undesired operation

of the device.

L’émetteur exempt de licence contenu dans le présent

appareil est conforme aux CNR d’Innovation, Sciences

et Développement économique Canada applicables

aux appareils radio exempts de licence. L’exploitation

est autorisée aux deux conditions suivantes :

1. L’appareil ne doit pas produire de brouillage;

2. L’appareil doit accepter tout brouillage radioélectrique

subi, même si le brouillage est susceptible d’en

compromettre le fonctionnement.

This equipment complies with IC RSS-102 radiation

exposure limits set forth for an uncontrolled environment.

This transmitter must not be co-located or operating

in conjunction with any other antenna or transmitter.

This equipment should be installed and operated with

minimum distance 20cm between the radiator and

your body.

Cet équipement est conforme aux limites d'exposition

aux radiations IC CNR-102 établies pour un environnement

non contrôlé. Cet émetteur ne doit pas être situé ou

fonctionner conjointement avec une autre antenne ou

un autre émetteur. Cet équipement doit être installé et

utilisé avec une distance minimale de 20 cm entre le

radiateur et votre corps.

IC warning

Speciﬁcation

This device contains licence-exempt transmitter(s)/re-

ceiver(s) that comply with Innovation,

Science and Economic Development Canada’s

licence-exempt RSS(s). Operation is subject to the

following two conditions:

1. This device may not cause interference; and

2. This device must accept any interference, including

interference that may cause undesired operation

of the device.

Cet appareil contient des émetteurs / récepteurs

exemptés de licence conformes aux RSS (RSS)

d'Innovation, Sciences et Développement

économique Canada. L'exploitation est autorisée aux

deux conditions suivantes :

1. l'appareil ne doit pas produire de brouillage, et

2. l'utilisateur de l'appareil doit accepter tout brouillage

radio électrique subi, même si le brouillage est

susceptible d'en compromettre le fonctionnement."

1. Do not exert excess force on the product.

2. Do not disassemble the product or let it come into

direct contact with heat or water.

3. Be careful when using the product in a hot or humid

environment as it may damage the circuit.

4. Do not place magnetized chip cards (e.g. ID cards, credit

cards) near the product as magnets may demagnetize

the cards and cause them to malfunction.

5. Do not place a foreign object between the charger and

then iPhone as the magnetic force may weaken.

6. Medical devices (e.g. pulse measuring device, hearing

aid) may indirectly interfere with the product; keep them

at least 20cm away from the product.

7. Keep away from children.

* The product image herein is provided as an example

and user's guide for the portable high-speed wireless

charger and may dier from the actual product.

* For smartphones that do not support wireless charging,

you need to use a separate wireless charging patch or

wireless charging case.

• Model : PF2009

• Input : DC 5.0V1.5A, 9.0V1.67A

• Output : 5.0W / 7.5W

• Dimensions (Not include Cable) : 62 x 62 x 6mm /

2.44 x 2.44 x 0.24in

• Weight (Include Built-in Cable) : 47g / 1.66oz

B Class Equipment (Equipment for home use)

* This product is mainly for home use with radio wave

acceptability registration; therefore, it can be used in all

areas.

Spigen PowerArc

ArcField™ Magnetic

Wireless Charger

for iPhone 12 Series

PF2009

Caution

20W USB-C PD Power Adapter is Recommended

for high-speed wireless charging.

USB Power Adapter is not included.

20W USB-C PD

Power Adapter

iPhone 12 series

O X

Do not pull on the

built-in cable when

detaching the wireless

charger. Pulling hard

on the cable will cause

short circuits.

Cutting Line (자르는�선)

Folding Line (접는�선)

PF2009_메뉴얼�수정 칼선/접선

(Cutting/Folding line)

작업자�의견

(Designer

comment)

*단순업무�외�기재�필요

지류

(Material) ART 120

HAN

47x93mm

Ver.

SKU

0 - 작업일

(Date)

자재�사이즈

(Size)

20. 11. 3 작업자

(Designer)

후가공

(Process)

Spigen PF2009 Manuel utilisateur

Marque: Spigen

Modèle: PF2009

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Spigen PF2009 User manual

Spigen PF2009 Manuel utilisateur

Spigen PF2009 Manuel utilisateur

dans d''autres langues

Autres documents