Babyletto Nifty Timber 3-in-1 Crib Manuel utilisateur

Marque: Babyletto

Modèle: Nifty Timber 3-in-1 Crib

Catégorie: Meubles de bébé

Taper: Manuel utilisateur

Timber 3-IN-1 Crib

Product Code: US0310

Nifty

revised 06AUG20

Nifty

Domestic child crib

Wood model

Instruction manual

Congratulations and

thank you for purchasing

an Ubabub product.

With our entire line of

clearly modern nursery

furniture, we are developing

cribs that have the capacity

to convert into a junior

bed and adapt with your

growing child. During the

design and production

of this product we have

selected materials that are

either recyclable or derived

from sustainable practices.

PERSONS REQUIRED ASSEMBLY TIME

TOOLS REQUIRED

– PHILLIPS HEAD SCREWDRIVER

– ALLEN KEY (SUPPLIED)

Contents

Contents & Hardware 3

Warning, Care & Maintenance 6

ALower rails position 10

BFront/Back panels position I 11

CFront/Back panels position II 12

DEnd panel assembly 13

E 14

Baseplate assembly

Close extra holes

Mattress support position

17Finished assembly

Contents

Panel x 1

(D) Back

Panel x 1

(E-1) Mattress

Support x 1

(F-1) Lower

Rail x 2

(A) Left End

Panel x 1

(B) Right End

Panel x 1

Hardware

(H4) 3/5” Round

Head Bolt x 16

(H2) 1-1/4” Allen

Head Bolt x 8

(H1) 2-1/4” Allen

Head Bolt x 4

(H3) 3/5” Allen

Head Bolt x 16

(H9) Allen Key x 1

(H8) Support Plate x 4

(H7) Wood Dowel x 4 (H10) 1-4/5” Allen

Head Bolt x 4

(H11) Curved Washer x 4

(H6) Lock

Washer x 16

(H5) Washer x 12

WARNING:

Failure to follow these warnings and

the assembly instructions could result

in serious injury or death.

READ ALL INSTRUCTIONS BEFORE ASSEMBLING

CRIB. KEEP THE MANUAL FOR FUTURE USE.

WARNING:

Parents should ensure a safe environment for the child by

checking regularly, before placing the child in the product,

that every component is properly and securely in place.

Please do NOT remove any wood screws in the normal disassembly

of the crib.

WARNING:

CAUTION: ANY MATTRESS USED IN THIS CRIB MUST BE

AT LEAST 27 1/4 INCHES (69CM) BY 51 5/8 INCHES (131CM)

WITH A THICKNESS NOT EXCEEDING 6 INCHES (15CM).

Please read the Caution and

Warning Statements insert

before using your crib.

Infants can suffocate on soft bedding. Never add a pillow or comforter. Never

place additional padding under an infant.

•

To reduce the risk of SIDS, pediatricians recommend healthy infants be placed •

on their backs to sleep, unless otherwise advised by your physician.

Strangulation Hazard: Strings can cause strangulation! Do not place items with •

a string around a child’s neck, such as hood strings or paciﬁer cords. Do not

place cords, straps,or similar items that could become wound around the child’s

neck in or near this crib. Do not suspend strings over a crib or attach strings to

toys.

To help prevent strangulation tighten all fasteners. A child can trap parts of the •

body or clothing on loose fasteners.

DO NOT place a crib near a window where cords from blinds or drapes may •

strangle a child. Do not place this crib near a window or a patio door where a

child could reach the cord of a blind or curtain and be strangled.

Fall Hazard: When a child is able to pull to a standing position, set the mattress •

to the lowest position and remove bumper pads, large toys and other objects

that could serve as steps for climbing out.

•

• Check this product for damaged hardware, loose joints, loose bolts or other

fasteners, missing parts or sharp edges before and after assembly and frequently

during use. Securely tighten loose bolts and other fasteners. DO NOT use crib if

any parts are missing, damaged or broken. DO NOT substitute parts. Contact MILLION

DOLLAR BABY CO. for replacement parts and instructional literature if needed.

DO NOT use a water mattress with this crib.•

For cribs equipped with teething rails, replace teething rail if damaged, cracked •

If reﬁnishing, use a non-toxic ﬁnish speciﬁed for children’s products.•

Never use plastic shipping bags or other plastic ﬁlms as mattress covers•

because they can cause suffocation.

Infants can suffocate in gaps between crib sides when used with a mattress •

that is too small.

• Follow warnings on all products in a crib.

• Ensure that the sides are properly latched or locked in place when the crib is occupied.

• The mattress used with this crib should not be more than 15cm thick and should be of

such length with width that the gap between the mattress and the sides of the crib is no

more than 3cm when the mattress is pushed into the corner of the crib.

or loose.

Do not use this crib if the child is able to climb out unaided or is taller than

35 in. (89cm).

• Do not use this crib if you cannot exactly follow the accompanying instructions.

Please refer to the label (sample below) on the inside face

of the headboard. Record the model/ item number and serial

number of your crib, the name of the store where you made

the purchase, the date of purchase and the wood finish in

the box to the lower right.

WE WILL ASK YOU FOR YOUR SERIAL NUMBER FOR ALL

WARRANTY AND REPLACEMENT PART REQUESTS. PLEASE

REFER TO THE LAST PAGE OF THIS INSTRUCTION SHEET FOR

WARRANTY INFORMATION. KEEP THIS MANUAL FOR FUTURE

REFERENCE.

THIS PRODUCT CONFORMS TO THE

APPLICABLE REGULATIONS OF THE

CONSUMER PRODUCTS SAFETY COMMISSION.

www.themdbfamily.com

CAUTION: ANY MATTRESS USED IN THIS CRIB

MUST BE AT LEAST 27 1/4 INCHES (69CM) BY

51 5/8 INCHES (131CM) WITH A THICKNESS

NOT EXCEEDING 6 INCHES (15CM).

SAMPLE LABEL

Storage:

Care and Cleaning:

• Solid woods exchange moisture with the air adjusting to major

changes in room temperature and humidity. Therefore, it is

best to place your furniture away from heating or air-

conditioning vents.

• Sunlight is not friendly to solid wood furniture and prolonged

direct exposure to harsh sunlight can discolor the ﬁnish. Be

careful not to place your furniture in direct sunlight for

extended periods of time. As with all your ﬁne furniture, blot up

spills immediately.

• Do not scratch or chip the ﬁnish. Do not use abrasive chemicals

for cleaning. Clean with mild soap on a soft rag. Rinse and dry

thoroughly. If you ever reﬁnish this furniture, be sure to use only

a non-toxic ﬁnish speciﬁed for children’s products. If you choose

to reﬁnish this furniture, the warranty will be voided.

8700 REX RD.

PICO RIVERA, CA 90660

IF YOU WOULD LIKE TO ORDER

REPLACEMENT OR MISSING PARTS

PLEASE VISIT US AT:

WWW.THEMDBFAMILY.COM/SUPPORT

OR YOU CAN CONTACT US BY MAIL:

MILLION DOLLAR BABY CO.

8700 REX RD.

PICO RIVERA, CA 90660

We will replace any missing parts at the time

of purchase or any defective item within

a one year period from the date of original

purchase. Please keep your receipt so that

we may process your warranty request. This

warranty only covers new units with original

packaging and ownership, and is not trans-

ferable. It does not cover any used, second-

hand or demo models.

This warranty does not cover any damaged

or defective parts that result from installation

and assembly, normal wear and tear, abuse,

negligence, improper use or alteration to the

ﬁnish, design, and hardware. The speciﬁc

legal rights of this warranty may vary from

state to state. Some states do not allow any

exclusion or limitation of incidental damages.

Some states do not allow limitation on how

long an implied warranty lasts.

ONE YEAR LIMITED WARRANTY:

Registering your product is even easier than

before. You can register your product on our

website at: www.themdbfamily.com/registrations

H7 X2

F-1

H10

H11

ALower rails position

BFront/Back panels position I

F-1

H6H5

CFront/Back panels position II

DEnd panel assembly

F-1

H10

H11

EBaseplate assembly

H4 H4

F-1

FClose extra holes

FOR YOUR BABY’S SAFETY:

THIS CRIB IS SUPPLIED WITH

EXTRA BOLTS THAT CLOSE

HOLES ACCESSIBLE TO YOUR

BABY. FAILURE TO USE THESE

BOLTS COULD RESULT IN

INJURY IF YOUR BABY’S

FINGERS GET STUCK IN THE

HOLES. WE RECOMMEND

THAT YOU USE THE BOLTS TO

CLOSE THE HOLES.

GMattress support position

E-1

* Make sure the mattress support

(E-1) is installed FLAT SIDE UP.

* Make sure the mattress support

(E-1) is level.

KEEP THIS MANUAL IN A SAFE PLACE FOR

FUTURE REFERENCE.

Recheck all screws and bolts to be sure they are

fastened securely. Do not overtighten.

Before using your crib, please read all cautionary

statements on the insert sheet.

Toddler bed rail (UB0399) is not included, sold separately.

Please contact your retailer to purchase.

HFinished assembly

Made in Vietnam

Lit de bébé 3 en 1 en bois

Code de produit: US0310

Nifty

Lit de bébé d’usage

domestique modèle en bois

Manuel d’instruction

PERSONNES

REQUISES

TEMPS

D’ASSEMBLAGE

OUTILS REQUIS

- TOURNEVIS CRUCIFORME

- CLÉ HEXAGONALE (FOURNIE)

Table des matières

Contenu et accessoires de montage 21

Avertissement, Entretien et nettoyage 24

APosition des rails inférieurs 28

BPosition des panneaux avant/

arrière I

CPosition des panneaux avant/

arrière II

Félicitations et merci d’avoir

acheté un produit Ubabub.

Avec notre ligne complète

de mobilier moderne pour

bébés, nous concevons des

lits de bébés pouvant se

convertir en lits pour tout-

petits, puis en lits d’enfants

grâce à la capacité de

s’adapter à leur croissance.

Lors de la conception et

de la production de ce

produit, nous avons choisi

des matériaux recyclables

ou dérivés de pratiques

durables.

DMontage du panneau

d'extrémité

EMontage de la plaque de base

FObstruction des trous

supplémentaires

GPosition du support du matelas

HFinition de l’assemblage

La page charge ...

Babyletto Nifty Timber 3-in-1 Crib Manuel utilisateur

Marque: Babyletto

Modèle: Nifty Timber 3-in-1 Crib

Catégorie: Meubles de bébé

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Babyletto Nifty Timber 3-in-1 Crib User manual

Babyletto Nifty Timber 3-in-1 Crib Manuel utilisateur

Babyletto Nifty Timber 3-in-1 Crib Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents