2
Table of contents
1 IMPORTANT SAFETY INSTRUCTIONS.....................3
1.1 Safety definitions........................................................4
1.2 General information....................................................4
1.3 General safety instructions.........................................4
1.4 Appliance handling safety ..........................................5
1.5 Safety codes and standards.......................................5
1.6 Electrical safety..........................................................5
1.7 Gas safety..................................................................5
1.8 Propane gas installation.............................................6
1.9 Ventilation recommendations.....................................6
1.10 High altitude installation ...........................................6
1.11 State of California Proposition 65 Warnings .............6
2 Before you begin........................................................7
2.1 Parts included ............................................................7
2.2 Tools and parts needed .............................................7
2.3 General requirements ................................................7
2.4 Cabinet requirements.................................................7
2.5 Countertop requirements ...........................................7
2.6 Gas requirements ......................................................8
2.7 Electrical requirements...............................................8
3 Prepare installation space.........................................8
3.1 Cutout dimensions .....................................................8
3.2 Flush mounting ..........................................................8
3.3 Cutout dimensions for flush mounting ........................9
3.4 Installation over oven .................................................9
3.5 Installation with horizontal panel.................................9
4 Installation procedure .............................................10
4.1 Preparing the cooktop..............................................10
4.2 Installing the pressure regulator ...............................10
4.3 Securing the cooktop in the countertop ....................11
4.4 Flush mounting ........................................................12
4.5 Connection overview................................................12
4.6 Connecting the gas supply line ................................13
4.7 Connecting the electrical supply...............................13
4.8 Assembling the burner parts ....................................13
4.9 Installing the burner grates.......................................14
4.10 Checking the installation ........................................14
5 Conversion to LP gas ..............................................15
5.1 Converting the pressure regulator............................15
5.2 Replacing the orifices...............................................16
5.3 Adjusting the gas valves ..........................................16
5.4 Burner chart .............................................................17
6 Customer Service ....................................................17
6.1 Model number (E-Nr.) and production number
(FD) .........................................................................18
6.2 Rating plate location.................................................18
en-us
3
Read all instructions carefully before use. These precautions will reduce the risk of electrical shock, fire and injury to
persons. When using kitchen appliances, basic safety precautions must be followed including those in the following
pages.
IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
en-us
4
1.1 Safety definitions
Here you can find explanations of the safety signal words
used in this manual.
WARNING
This indicates that death or serious injuries may occur as
a result of non-observance of this warning.
CAUTION
This indicates that minor or moderate injuries may occur
as a result of non-observance of this warning.
NOTICE:
This indicates that damage to the appliance or property
may occur as a result of non-compliance with this advi-
sory.
Note:This alerts you to important information and/or tips.
1.2 General information
¡Read this manual carefully.
¡Keep the manual and the product information in a safe
place for future reference or for the next owner.
¡Do not connect the appliance if it has been damaged in
transit.
1.3 General safety instructions
IMPORTANT: THE APPLIANCE MUST BE INSTALLED
BY A QUALIFIED INSTALLER.
IMPORTANT: SAVE THESE INSTRUCTIONS FOR THE
LOCAL ELECTRICAL INSPECTOR’S USE.
OWNER: PLEASE RETAIN THESE INSTRUCTIONS
FOR FUTURE REFERENCE.
INSTALLER: LEAVE THESE INSTRUCTIONS WITH
THE APPLIANCE AFTER INSTALLATION IS COM-
PLETE.
Examine the appliance after unpacking it. In the event of
transport damage, do not plug it in.
WARNING
If the information in this manual is not followed exactly, fire
or shock may result causing property damage or personal
injury.
Do not repair, replace or remove any part of the appliance
unless specifically recommended in the manuals. Im-
proper installation, service or maintenance can cause in-
jury or property damage.
▶Refer to this manual for guidance.
▶All other servicing should be done by an authorized ser-
vice provider.
Disconnect electrical and gas supply before servicing.
When installing a cooktop over a single oven, be sure to
follow the instructions in both the oven's and the cooktop's
installation manuals.
▶You can find a list of approved combinations of cooktop
and oven in the Approved Combination Matrix of your
cooktop, or you can contact Customer Service for the
latest list of approved combinations. Do not try to install
your cooktop over any oven that is not stated in that list.
Never modify or alter the construction of the appliance.
The appliance should only be used if installed by a quali-
fied technician in accordance with these installation in-
structions. The manufacturer is not responsible for any
damage resulting from incorrect installation.
To eliminate the risk of burns or fire by reaching over
heated surface units, cabinet storage space located above
the surface units should be avoided.
▶If cabinet storage is to be provided, the risk can be re-
duced by installing a hood that projects horizontally a
minimum of 5" (127mm) beyond the bottom of the cabi-
net.
▶Verify that cabinets above the cooktop are a maximum
of 13" (330mm) deep.
WARNING
The bottom of the cooktop can become hot.
▶If the cooktop is not installed in combination with an
oven, install a horizontal panel below the cooktop to
prevent accidental contact. Refer to the section on in-
stalling a horizontal panel. →
Page9
WARNING
Remove all tape and packaging before using the appli-
ance.
▶Destroy the packaging after unpacking the appliance.
▶Dispose of packaging in an environmentally responsible
manner.
▶Never allow children to play with packaging material.
▶Store small parts safely as they can be a choke hazard.
IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
en-us
5
1.4 Appliance handling safety
WARNING
Hidden surfaces may have sharp edges.
▶Use caution when reaching behind or under appliance.
1.5 Safety codes and standards
This appliance complies with the latest version of one or
more of the following standards:
¡ANSI Z21.1 / CSA 1.1 Household Cooking Gas Appli-
ances
¡Installation must conform with local codes or, in the ab-
sence of local codes, with the National Fuel Gas Code,
ANSI Z223.1/NFPA 54 or, in Canada, the Natural Gas
and Propane Installation Code, CSA B149.1.
It is the responsibility of the owner and the installer to de-
termine if additional requirements and/or standards apply
to specific installations.
1.6 Electrical safety
¡Installer - show the owner the location of the circuit
breaker or fuse. Mark it for easy reference.
¡If required by the National Electrical Code (or Canadian
Electrical Code), this appliance must be installed on a
separate branch circuit.
¡Local codes vary. The installer is responsible for ensur-
ing that the installation, connections, and grounding
comply with all applicable codes. The manufacturer is
not responsible for any issues associated with the im-
proper installation of this product.
¡The appliance must be electrically grounded in accor-
dance with local codes or, in the absence of local
codes, with the National Electrical Code, NFPA 70 lat-
est edition or, in Canada, the Canadian Electric Code,
CSA C22.1-02.
¡Be sure your appliance is properly installed and
grounded by a qualified technician. Installation, electri-
cal connections and grounding must comply with all ap-
plicable codes.
¡Do not use an extension cord.
¡Do not use an adapter.
¡Refer to the rating plate for more information.
→
"Rating plate location", Page18
WARNING
Before installing, turn power OFF at the service panel.
▶Lock service panel to prevent power from being turned
ON accidentally.
For appliances equipped with a cord and plug, do not cut
or remove the ground prong.
▶It must be plugged into a matching grounding type re-
ceptacle to avoid electrical shock.
▶If there is any doubt as to whether the wall receptacle is
properly grounded, the customer should have it
checked by a qualified electrician.
GROUNDING INSTRUCTIONS
▶This appliance must be grounded.
▶Grounding reduces the risk of electric shock by provid-
ing a safe pathway for electric current in the event of a
short circuit.
▶Be sure your appliance is properly installed and
grounded by a qualified technician.
▶Installation, electrical connections and grounding must
comply with all applicable codes.
Do not use an extension cord. If the power supply cord is
too short, have a qualified electrician install an outlet near
the appliance.
Before you plug in an electrical cord, be sure all controls
are in the OFF position.
Before you turn on power supply, make sure all controls
are in the OFF position.
1.7 Gas safety
Requirements for gas supply:
¡Install a gas shutoff valve near the appliance. It must be
easily accessible in an emergency.
¡Leak testing must be conducted by the installer accord-
ing to the instructions in this manual.
¡The appliance and its individual shutoff valve must be
disconnected from the gas supply piping system during
any pressure testing at pressures in excess of ½psi
(3.5kPa).
¡The appliance must be isolated from the gas supply
piping system by closing its individual manual shutoff
valve during any pressure testing of the gas supply pip-
ing system at test pressures equal to or less than ½psi
(3.5kPa).
IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
en-us
6
¡The minimum supply pressure must be 1" water column
above the manifold pressure printed on the rating label.
The maximum supply pressure must not exceed 14.0
inches water column (34.9Millibars).
¡A metal flex line or fixed metal pipe shall be used to
connect gas to the appliance. If a metal gas line cannot
be used, consult your local certified electrician or local
electric codes for proper grounding.
IMPORTANT SAFETY NOTICE: Burning gas cooking fuel
generates some by-products which are on the list of sub-
stances which are known by the State of California to
cause cancer or reproductive harm. To minimize exposure
to these substances, always operate this unit according to
the instructions contained in this booklet and provide good
ventilation.
1.8 Propane gas installation
¡The propane gas tank must be equipped with its own
high pressure regulator. In addition, the regulator sup-
plied with this unit must also be used.
¡The appliance is shipped from the factory for use with
natural gas. It must be converted for use with propane.
A qualified technician or certified installer must do the
conversion.
¡For use with propane the appliance must be converted
per the LP conversion instructions.
→
"Conversion to LP gas", Page15
For Massachusetts installations
¡Installation must be performed by a qualified or li-
censed contractor, plumber or gas fitter qualified or li-
censed by the state, province or region where this ap-
pliance is being installed.
¡Shut-off valve must be a “T” handle gas cock.
¡Flexible gas connector must not be longer than
36inches.
Installer - show the owner where the gas shut-off valve is
located.
1.9 Ventilation recommendations
We strongly recommend the installation of a ventilation
hood above this appliance.
The hood must be installed according to instructions fur-
nished with the hood.
WARNING
The appliance should not be installed with a ventilation
system that blows air downward toward the burners. This
type of ventilation system may cause ignition and combus-
tion problems with the gas cooking appliance resulting in
personal injury or unintended operation.
1.10 High altitude installation
This appliance has been tested for operation up to an alti-
tude of 10,100ft (3,080m) elevation above sea level.
For altitudes above 2,000ft (610m) elevation above sea
level, burner flame adjustments may be necessary.
Burners should be checked at the lowest setting, if the
flame is not stable the simmer should be increased until
the flame is stable. This can be done by adjusting the by-
pass screw in the valve. If flame performance is satisfac-
tory, adjustment will not be required. It is required that a
certified professional make the high altitude adjustments
during installation.
1.11 State of California Proposition 65
Warnings
This product may contain a chemical known to the State
of California, which can cause cancer or reproductive
harm. Therefore, the packaging of your product may bear
the following label as required by California:
IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
Before you begin en-us
7
Before you begin
2 Before you begin
Before you begin
Read these instructions before you begin to install your
appliance.
2.1 Parts included
After unpacking all the parts, check for any damage in
transit and for completeness of delivery.
¡Cooktop
¡Foam tape
¡Hold-down brackets (4)
¡Sheet metal screws, DIN7982 4.2x25 (1") (4)
¡Burner grates (3)
¡Burners (5)
¡Burner caps (6)
¡Pressure regulator
¡LP gas conversion kit
¡OptiSim® Cap (1)
2.2 Tools and parts needed
Prepare these tools and accessories before you start to in-
stall your appliance.
¡Pencil
¡Measuring tape
¡Cross head screwdriver
¡Drill with bit 1/4" (6mm)
¡Jigsaw
¡Adjustable wrench
¡Teflon® tape - gas rated
¡Flathead screwdriver, 1/8"
Additional tools needed for LP gas conversion
¡7mm socket wrench
¡7mm open end wrench
¡T10 star bit screwdriver
¡T20 star bit screwdriver
¡Small piece of tape
Notes
¡For stand-alone installation a horizontal panel below the
cooktop may be needed.
→
"Installation with horizontal panel", Page9
¡Additional materials may be necessary for installation in
solid surface countertops. Contact the countertop man-
ufacturer.
2.3 General requirements
Ensure that the following requirements are met when plan-
ning the installation of your appliance.
¡Plan the installation of the unit so that the power cord,
gas shut-off valve and gas pressure regulator are ac-
cessible from the front of the cabinet.
¡Make sure the gas supply line does not interfere with
the back of the appliance.
¡The cabinet in which the cooktop is installed must be
properly secured, level and stable.
¡Any laminated coverings and glue on cabinets next to
the cooktop must be made of non-flammable and heat
resistant materials. Refer to local building codes for ac-
ceptable materials.
¡This appliance cannot be installed above refrigerators,
washing machines, dishwashers or similar.
¡If the cooktop will be installed in combination with an
oven, refer to the Approved Combination Matrix in-
cluded with the product for cutout and clearance dimen-
sions.
2.4 Cabinet requirements
Ensure that the cabinetry at the installation location meets
the requirements for a safe installation.
The minimum spaces that must be maintained when in-
stalling the gas cooktop shall be the following:
a min. 12¾" (325mm)
for installation next to oven min. 13" (330mm)
b min. 12¾" (325mm)
for installation next to oven min. 13" (330mm)
c min. 30" (762mm) clearance between the top of
the cooking surface and the bottom of combustible
constructions
d min 2¼'' (58 mm);
for installation in kitchen islands, min. 4" (100mm)
e For 30" cooktops:
min. 30" (760mm) centered over cooktop
f min. 18" (458mm)
g max. 13" (330mm)
h min. 1¼" (32mm);
for installation in kitchen islands, min. 4" (100mm)
2.5 Countertop requirements
Ensure that the countertop into which the cooktop is to be
installed meets these requirements for a safe installation.
WARNING
To reduce the risk of ignition of surrounding combustible
materials, install at least 12¾" (325mm) from both side-
walls and at least 2¼'' (58 mm) from the rear wall.
¡The countertop must be level.
¡The stability of the countertop must be maintained after
the cut-out has been made.
en-us Prepare installation space
8
¡Solid surface or laminate countertops often require spe-
cial installations. For example, heat-reflective tape and
rounded corners may be necessary. Contact the coun-
tertop manufacturer for instructions specific to your
countertop.
2.6 Gas requirements
Ensure that the requirements for the gas supply are met.
The cooktop is shipped from the factory for use with natu-
ral gas. For use with LP conversion, a certified technician
or installer must do the conversion.
Supply pressure:
¡Natural Gas: 7 inches water column (17.4 Millibars)
¡Propane Gas: 11 inches water column (27.4 Millibars)
¡The propane gas tank must be equipped with its own
high pressure regulator in addition to the pressure regu-
lator supplied with this unit.
2.7 Electrical requirements
Ensure that the following electrical requirements are met.
CAUTION
Do not use an extension cord with this appliance.
¡This appliance requires a 60Hz, 15Amp, 120V/AC
connection.
¡The appliance is equipped with a 40" (1000mm) power
cord.
¡The power connection must remain accessible from the
front of the cabinet after the installation is complete.
Prepare installation space
3 Prepare installation space
Prepare installation space
Create the cutout in the countertop according to the in-
structions.
General countertop requirements:
¡The angle of the cut surface to the countertop surface
must be 90°.
¡With multi-layered countertops, secure strips laterally in
the cutout if necessary.
¡After creating the cutout, remove all debris.
¡Follow the countertop manufacturer's recommendations
for protecting the cut edges, e.g. apply heat resistant foil
tape.
¡If the cooktop will be installed in combination with an
oven, refer to the Approved Combination Matrix in-
cluded with the product for cutout and clearance dimen-
sions.
¡Observe the minimum distance between device under-
side and cabinet surfaces of ⅜" (10mm).
WARNING
The bottom of the cooktop can become hot.
▶If the cooktop is not installed in combination with an
oven, install a horizontal panel below the cooktop to
prevent accidental contact. Refer to the section on in-
stalling a horizontal panel. →
Page9
3.1 Cutout dimensions
*For installation in a kitchen island.
3.2 Flush mounting
The cooktop can be mounted flush into the countertop.
¡All cut-out work in the countertop surface should be per-
formed by a qualified craftsman.
¡The cut-outs should be clean and precise, as the cut
edge will be visible after installation. The stability of the
countertop must be ensured after cutting work.
¡Use only specially designed work surfaces, resistant to
high temperature and water (e.g. natural stone or tile).
¡Surrounding cabinetry must be resistant to tempera-
tures of up to 195°F (90°C).
Prepare installation space en-us
9
3.3 Cutout dimensions for flush mounting
*For installation in a kitchen island.
3.4 Installation over oven
A min. ¾" (19 mm)
max. 2" (50 mm)
B 5⅞" (150 mm)
C 2¾" (70 mm)
D Refer to Approved Combination Matrix
E 2⅜" (60)
3.5 Installation with horizontal panel
If there is no oven beneath the cooktop, install a horizontal
panel. To allow access to the power supply connection
and regulator maintain a minimum clearance of
⅜" (10mm) from the edges of the panel(F).
IMPORTANT: Complete the installation of the cooktop be-
fore installing the horizontal panel.
Installation above a drawer
A min. ¾" (19 mm)
max. 2" (50 mm)
B 5⅞" (150 mm)
C 2¾" (70 mm)
D min. 0" (0 mm)
E 2⅜" (60)
F min. ⅜" (10 mm)
en-us Installation procedure
10
Installation above a cabinet door
A min. ¾" (19 mm)
max. 2" (50 mm)
B 5⅞" (150 mm)
C 2¾" (70 mm)
D min. 0" (0 mm)
E 2⅜" (60)
F min. ⅜" (10 mm)
G min. 1" (25)
Installation procedure
4 Installation procedure
Installation procedure
Follow these instructions to install the cooktop into the
countertop.
CAUTION
Sharp edges.
▶Use protective gloves when installing the appliance.
CAUTION
The appliance is heavy.
▶It is recommended that two people install this appliance.
4.1 Preparing the cooktop
1. Place the cooktop face down on a soft and stable sur-
face. Use the foam sheet from the packaging to protect
surfaces from scratching.
2. Apply the included foam sealing tape around the edges
of the underside of the appliance.
3. Attach the hold-down brackets to the underside of the
cooktop with the provided short screws. Loosely tighten
the screws so the clamps do not move freely. Rotate
the hold-down brackets so that the appliance can be
placed in the cutout.
4.2 Installing the pressure regulator
WARNING
Do not attempt any adjustment of the pressure regulator,
except when converting to propane. Adjustments could
lead to leaks or cause incorrect gas pressure to the appli-
ance.
Make sure the used gas connection line is not connected
to the gas supply, before carrying out the following steps.
Note:All pipe connections must be sealed in accordance
with local codes.
Installation procedure en-us
11
1. Identify the parts of the pressure regulator.
a Appliance manifold connection
b Conversion cap
c Pressure regulator
d Arrow on pressure regulator, shows the direc-
tion of gas flow
2. Apply Teflon® tape on the threads of the manifold pipe.
Install the pressure regulator (supplied with cooktop) to
the gas inlet with the gas flow arrow facing the manifold
inlet.
3. Firmly hand tighten the regulator, then further tighten ¼
turn to a maximum of one complete turn. Align the regu-
lator so that the conversion cap is easily accessible.
4. WARNING Never reuse a gas connector. Re-
peated bending, flexing, or extreme vibration will cause
metal fatigue and must be avoided.
Apply Teflon® tape to the male threads, then connect a
new ½" metal flex line or fixed metal pipe connection to
the pressure regulator.
Note:For installations with little space, a suitable kit is
available from Customer Service (order no.00611084).
4.3 Securing the cooktop in the countertop
The cooktop must be secured from below using the hold-
down brackets provided.
WARNING
Before installing, turn power OFF at the service panel.
▶Lock service panel to prevent power from being turned
ON accidentally.
1. CAUTION Do not let the cooktop drop into place.
▶Make sure that the cooktop is supported along the
edges when carefully placing it into the cutout.
Turn the cooktop over carefully making sure not to dam-
age the pressure regulator and gas line.
‒Place the cooktop carefully into the countertop
cutout, pulling it towards the front of the cutout .
‒Lower the rear of the cooktop so that is rests flat on
the counter .
‒Center the cooktop left and right in the cutout .
2. Rotate the hold-down brackets so that they will contact
the underside of the countertop.
‒Hand-tighten one hold-down bracket and check the
cooktop position, then secure the cooktop by tighten-
ing all the brackets. Do not over-tighten.
‒The orientation of the hold-down brackets depends
on the thickness of the countertop. For countertops
between 2" (50mm) and 2¾" (70mm) thick, insert a
wooden block between the end of the hold-down
bracket and the bottom of the countertop.
en-us Installation procedure
12
a Cooktop
b Countertop
c Wooden block
Required for installation in countertops that
are between 2" (50mm) and 2¾" (70mm)
thick.
d Long clamping screw
Required for installation with wooden block.
Available for purchase from Customer Ser-
vice (order no.10011930).
Note:Do not use silicone to glue the cooktop to the coun-
tertop surface.
4.4 Flush mounting
1. Complete the normal installation of the appliance mak-
ing sure that it is surrounded by a uniform slot. The
cooktop surface should be slightly below the countertop
surface. For tiled countertops, raise the supporting sur-
faces with water- and temperature-resistant strips, if
necessary.
2. Check the operation and position of the appliance.
3. Fill the gap between the countertop and the cooktop
with conventional silicone sealant in the desired color.
Unsuitable silicone sealant used on natural stone sur-
faces can lead to discolorations that cannot be re-
moved. Follow the manufacturer’s instructions for the
silicone sealant.
4. Smooth the silicone sealant with a wet and soapy
scraper or finger before it forms a layer.
5. Allow the silicone sealant to dry before using the appli-
ance.
4.5 Connection overview
Refer to this illustration for the location of the gas and
electric connection of the appliance.
Note:Your appliance is equipped for use with natural gas
on delivery. If you want to use your appliance with LP gas
refer to the section on LP gas conversion before continu-
ing with the installation.
a Cooktop rough-in box
b Arrow on pressure regulator, shows the direction of
gas flow
c Pressure regulator
d ½" female pipe threads
e Metal flex gas line
f Power cord (40"/1m)
g 120V receptacle
h Gas cut-off valve
i Gas supply line connection fitting
j Floor
Installation procedure en-us
13
4.6 Connecting the gas supply line
The appliance is shipped from the factory for use with nat-
ural gas. If you want to use propane gas it must be con-
verted. A qualified technician or installer must do the con-
version.
Note
Ensure the following requirements are met before you try
to connect the appliance to the gas supply:
¡Before connecting the appliance, check whether the lo-
cal connection conditions such as gas type and gas
pressure match the appliance settings.
¡Make sure the gas supply is turned off at the manual
shutoff valve before connecting the appliance.
¡The gas connection must be in a location that permits
access to the manual shut-off valve and which, if appli-
cable, is visible after opening the door or drawers of the
cabinet.
¡The metal flex gas line must not come into contact with
moving parts of the fitted unit (e.g. drawers) or be laid in
areas where it could become trapped or damaged.
¡The metal flex gas line must not come into contact with
a cooktop, oven, dishwasher, refrigerator, washing ma-
chine, hot water pipe, radiator or any other appliance in-
stalled in the vicinity of the gas cooktop.
¡The metal flex gas line must not be subject to rubbing,
vibrations, kinking or any other kind of deformation. It
should be checked along its entire length with the cook-
top in the installation position.
¡All pipe connections must be sealed in accordance with
local codes.
▶Connect the metal flex gas line or fixed metal pipe con-
nection from the cooktop pressure regulator to the man-
ual shut-off valve.
Checking the gas line for leaks
Check the gas supply line connections for leaks using a
soap solution or non-corrosive leak detection fluid. Do not
use a flame of any sort.
Note
Important notes for gas connection:
¡The appliance and its individual shutoff valve must be
disconnected from the gas supply piping system during
any pressure testing at pressures in excess of ½psi
(3.5kPa).
¡The appliance must be isolated from the gas supply pip-
ing system by closing its individual manual shutoff valve
during any pressure testing of the gas supply piping
system at test pressures equal to or less than ½psi
(3.5kPa).
1. Turn on gas.
2. Apply a soap solution or non-corrosive leak detection
fluid to all joints and fittings in the gas connection be-
tween the shut-off valve and the cooktop. Also check
gas fittings and joints in the cooktop if the connections
may have been disturbed during installation.
aBubbles appearing around fittings and connections indi-
cate a leak.
3. If a leak appears, turn off the supply line gas shut-off
valve and tighten the connections.
4. Retest for leaks by turning on the supply line gas shutoff
valve.
aWhen the leak check is complete and no bubbles ap-
pear, the test is complete.
5. Wipe off all soap solution or detection fluid residue.
4.7 Connecting the electrical supply
CAUTION
Before you plug in the electrical cord, make sure that the
gas shut-off valve and all burner controls are in the OFF
position.
▶Connect the plug of the electrical cord to a grounded
power outlet. The outlet must be accessible after the in-
stallation of the appliance is complete.
4.8 Assembling the burner parts
The burner parts must be properly placed for the cooktop
to function properly.
Note
If the burner parts are not properly placed, one or more of
the following problems may occur:
¡The burner flames are too high.
¡Flames shoot out of the burners.
¡The burners do not ignite.
¡The burner flames light unevenly.
¡The burners emit gas odor.
WARNING
Remove all tape from the burner parts and the cooktop
surface before using the appliance.
1. Assemble the burner parts according to the illustration.
1
2
3
4
4
3
2
1
1
Burner cap
2
Burner base
3
Thermocouple
4
Igniter
Make sure that the prongs of the burner cap fit snugly
into the groove of the burner base.
en-us Installation procedure
14
2. Check to make sure that there is no gap between the
burner parts. You may gently try to move the burner
parts from side to side to check if they are properly
seated.
4.9 Installing the burner grates
WARNING
Improperly positioned grates can cause flare-ups.
▶Position all grates properly on the cooktop whenever
the cooktop is in use to properly support pots and avoid
spills.
▶Make sure each of the four feet of the grates is placed
into the corresponding dimples on the cooktop surface.
▶Do not use a grate if the rubber feet are missing or
damaged.
4.10 Checking the installation
Check if your unit is working properly after you have com-
pleted the installation steps.
WARNING
Before you turn on power supply, make sure all controls
are in the OFF position.
1. Ensure that the burner caps are properly positioned.
2. Turn each burner on in turn and verify that the electric
igniters are working.
3. Turn the control knob between the highest and lowest
setting. Make sure the flame does not go out and there
are no flashbacks.
4. If you have carried out an LP gas conversion, check the
lowest setting to confirm the flames are stable on the
ports and the set screws do not need to be readjusted.
5. Check the flame characteristics.
The flame should be blue with a minimal yellow tip on
the outer cone.
6. After completing all checks, complete the installation of
the horizontal panel or oven. →
Page9
Note:The appliance is shipped from the factory for use
with natural gas. If you want to use propane gas, it must
be converted. A qualified technician or installer must do
the conversion. Refer to Conversion to LP gas.
Flame characteristics
The color of the flame tells you if the gas supply is properly adjusted.
Note:Allow the appliance to operate for 4 to 5minutes before evaluating the flame. Some yellow streaking is normal dur-
ing the initial startup.
Flame Image Measure
Completely or mostly
yellow Verify that the regulator is set for the correct fuel. Retest af-
ter adjustment.
Yellow tips on outer
cone Normal for LP gas
Conversion to LP gas en-us
15
Flame Image Measure
Soft blue Normal for natural gas
Conversion to LP gas
5 Conversion to LP gas
Conversion to LP gas
Your appliance is equipped for use with natural gas on de-
livery. It can be converted to LP gas supply.
The components required for conversion to LP gas are
contained in the LP conversion kit included with this appli-
ance, or are available from Customer Service.
→
"Customer Service", Page17
Only a qualified technician or installer is authorized to con-
vert the appliance to another gas type.
Before carrying out the conversion, turn off the electricity
and gas supply.
5.1 Converting the pressure regulator
WARNING
Turn off the electricity and gas supply before carrying out
the conversion.
1. Locate the pressure regulator on the bottom right end of
the appliance.
2. Remove the hexagon shaped conversion cap from the
regulator. Make sure not to dislodge the gasket on
the cap or the spring inside the regulator.
3. Grasp the plastic orifice stem firmly and pull it force-
fully from the conversion cap . The stem snaps snugly
into an indent in the cap and may require a strong pull
to remove. It may be helpful to gently “rock” the plastic
stem while pulling it from the metal cap.
4. Rotate the stem 180° .
aConfirm that the button end of the orifice stem is away
from the conversion cap.
aConfirm that the letters “LP” on the orifice stem are up-
side down when the conversion cap is set flat on its
head.
5. Snap the orifice stem back in place in this position in-
serting it into the indent in the conversion cap .
6. Insert the hexagon cap back into the regulator and
tighten, do not over-tighten.
en-us Conversion to LP gas
16
7. IMPORTANT: Attach the metallic sticker included with
the LP conversion kit to the bottom of the appliance as
shown. This sticker provides notice that the appliance
has been converted for use with LP gas. It should be lo-
cated near the appliance rating plate.
→
"Rating plate location", Page18
Note:If you change the type of gas back to natural gas
at a later point, remove the sticker.
5.2 Replacing the orifices
1. Remove all burner grates, burner caps and burner
bases.
2. Remove the natural gas orifices and replace them with
LP orifices using a 7mm socket wrench. See burner
chart.
‒For ease of installation use a small piece of tape and
insert it in the socket wrench to prevent the orifice
from falling out.
‒It is important to make sure that the orifices do not
become detached during removal or fastening. They
must be properly tightened to ensure that there are
no leaks.
Normal burner with one orifice
Double burner, first orifice
Double burner, second orifice
3. Fasten the orifices.
4. Save the orifices removed from the appliance for future
use.
5.3 Adjusting the gas valves
Note:In the event of damage, the gas valve must be com-
pletely replaced.
1. Turn the control knobs to the off position.
2. Pull off the control knobs.
Customer Service en-us
17
3. Remove the white rings underneath the control knobs.
aA flexible black rubber sealing ring is visible.
aIMPORTANT: Never remove the sealing rings. They
prevent liquids and dirt from moving into the appliance,
which may impair proper functioning.
4. Below the left upper position of the black rubber sealing
ring is a visible black star T10 screw, partly hidden by
the seal. Use a long thin T10 screwdriver to press the
black rubber sealing ring aside slightly to access this
setting screw.
The dual-flame burner has 2 setting screws.
5. Refer to the burner chart for the correct setting of the
setting screws (M).
→
"Burner chart", Page17
‒Use setting for LP Gas. The setting screws must
be tightened properly.
‒Use setting for natural gas. The setting screws
must finish flush with the fitting.
6. Replace the white rings and the control knobs.
7. Turn the control knob between the highest and lowest
setting. Make sure the flame does not go out and there
are no flashbacks.
5.4 Burner chart
Refer to this overview for specifications of the individual burners.
Burner
cap Gas type Pressure
in inch
wc
Orifice BTU/h kW M (valve ad-
justment screw
setting)
Small
burner Natural gas
Propane gas 6
10 77
54 3,400
3,400 1
1
Medium
burner Natural gas
Propane gas 6
10 102
71 6,000
6,000 1.76
1.76
Large
burner Natural gas
Propane gas 6
10 133
93 10,300
10,300 3.02
3.02
Dual
burner Natural gas
Propane gas 6
10 NG:
¡outer: 144
¡inner: 74
PG:
¡outer: 100
¡inner: 51
14,300
14,300 4.19
4.19
Customer Service
6 Customer Service
Customer Service
With any warranty repair, we will make sure your appli-
ance is repaired by an authorized service provider using
genuine replacement parts. We use only genuine replace-
ment parts for all repairs.
Detailed information on the warranty period and terms of
warranty can be found in the Statement of Limited Product
Warranty, from your retailer, or on our website.
If you contact the Customer Service, you will need the
model number (E-Nr.) and the production number (FD) of
your appliance.
USA:
1-800-944-2904
www.bosch-home.com/us/owner-support/get-support
www.bosch-home.com/us/shop
CA:
1-800-944-2904
www.bosch-home.ca/en/service/get-support
www.bosch-home.ca/en/service/cleaners-and-accessories
en-us Customer Service
18
6.1 Model number (E-Nr.) and production
number (FD)
You can find the model number (E-Nr.) and the production
number (FD) on the appliance's rating plate.
Making a note of your appliance's details and the Cus-
tomer Service telephone number will enable you to find
them again quickly.
6.2 Rating plate location
You can find the rating plate of your appliance:
¡On the appliance certificate.
¡On the underside of the appliance.
Rating plate
fr-ca
19
Table des matières
1 IMPORTANTES CONSIGNES DE SÉCURITÉ .........20
1.1 Définitions des termes de sécurité ...........................21
1.2 Indications générales ...............................................21
1.3 Consignes générales de sécurité .............................21
1.4 Manipulation sécuritaire des appareils .....................22
1.5 Codes et normes de sécurité ...................................22
1.6 Sécurité électrique ...................................................22
1.7 Sécurité des gaz ......................................................23
1.8 Installation au gaz propane ......................................23
1.9 Recommandations de ventilation .............................23
1.10 Installation à haute altitude.....................................23
1.11 Mises en garde conformément à la proposition
65 de l'État de Californie ........................................24
2 Avant de commencer...............................................25
2.1 Pièces incluses ........................................................25
2.2 Outils et pièces nécessaires.....................................25
2.3 Conditions générales ...............................................25
2.4 Exigences concernant les armoires..........................25
2.5 Exigences du comptoir.............................................26
2.6 Exigences en matière de gaz ...................................26
2.7 Exigences électriques ..............................................26
3 Préparation préalable au montage .........................26
3.1 Dimensions de la découpe.......................................26
3.2 Montage encastré ....................................................26
3.3 Dimensions de découpe pour montage encastré .....27
3.4 Installation au-dessus du four ..................................27
3.5 Installation avec panneau horizontal ........................27
4 Procédure d’installation ..........................................28
4.1 Préparation de la table de cuisson ...........................28
4.2 Installation du régulateur de pression.......................28
4.3 Fixation de la table de cuisson dans le comptoir ......29
4.4 Montage encastré ....................................................30
4.5 Aperçu de la connexion............................................30
4.6 Raccordement de la conduite d’alimentation en
gaz...........................................................................31
4.7 Connexion de l'alimentation électrique .....................31
4.8 Assemblage des pièces du brûleur ..........................31
4.9 Installation des grilles de brûleur..............................32
4.10 Inspecter l’installation.............................................32
5 Conversion au gaz LP..............................................33
5.1 Conversion du régulateur de pression......................33
5.2 Remplacement des orifices......................................34
5.3 Ajustement des soupapes de gaz ............................34
5.4 Tableau des brûleurs ...............................................35
6 Service à la clientèle................................................35
6.1 Numéro de modèle (E-Nr.) et numéro de
fabrication (FD) ........................................................36
6.2 Emplacement de la plaque signalétique...................36
fr-ca
20
Lisez toutes les instructions attentivement avant l’utilisation. Ces précautions réduiront le risque d’électrocution,
d’incendie et de blessure pour les personnes utilisant l’appareil. Lorsque vous utilisez des appareils électroménagers,
il importe de suivre les précautions de sécurité de base, y compris celles indiquées dans les pages suivantes.
IMPORTANTES CONSIGNES DE SÉCURITÉ
LIRE ET CONSERVER CES INSTRUCTIONS
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
dans d''autres langues
- English: Bosch NGMP077UC User manual
- español: Bosch NGMP077UC Manual de usuario