Champion Power Equipment C20049 Le manuel du propriétaire

INTRODUCTION

Congratulations on your purchase of a Champion Power Equipment winch.

CPE designs and builds winches to strict specifications and with proper use

and maintenance should bring you years of satisfying service.

WARNING - Read, study and follow all instructions before operating this

device. Failure to heed these instructions may result in personal injury and/or

property damage.

Your winch can develop tremendous pulling forces and if used unsafely or

improperly could result in property damage, serious injury or death.

Throughout this manual you will find the following symbols for caution, warning

and danger. Pay particular attention to the notes preceded by these symbols as

they are written for your safety. Ultimately, safe operation of this device rests

with you, the operator.

Indicates a potentially hazardous situation which, if not avoided, may

result in minor or moderate injury. This notation is also used to alert

against unsafe practices.

Indicates a potentially hazardous situation which, if not avoided

could result in death or serious injury.

CAUTION

INCLUDED WITH YOUR WINCH

DESCRIPTION QUANTITY

1. Winch Assembly with Wire Rope 1

2. Cap Bolt M8 x 30 2

3. Lock Washers 2

4. Flat Washers 2

5. M8 Nuts 2

6. Snatch Block/Pulley 1

7. Clevis Hook w/Pin 1

8. Power Cord/Switch Assembly 1

9. Hand Saver Hook 1

WINCH ACCESSORIES YOU WILL NEED

NOT INCLUDED WITH YOUR WINCH

Gloves – For handling the wire rope and hook strap.

Clevis/D-shackle – For connecting your snatch block and anchor strap.

Anchor Strap/Chain – Tree saver anchor straps are made of high quality nylon

with high tensile strengths from 5,000 to 10,000lbs.

Heavy Blanket – place on the cable to absorb energy should the wire rope

break.

Winch ASSEMBLY AND MOUNTING

1. Your CPE 2,000 lb winch is designed with a bolt pattern that is standard

in this class of winch. Many winch mounting kits are available that utilize

this bolt pattern for the most popular ATV’s and mounting channels. If

you cannot find a kit locally, contact CPE and we will provide you with the

name of a dealer near you.

2. Regardless of the mounting kit you use, ensure that your CPE winch is

mounted on a flat surface so that the three major sections (motor, drum

and gear housing) are properly aligned. Proper alignment of the winch

will allow even distribution of the full rated load.

3. Utilize the M8 x 30 mounting bolts, washers and nuts included.

4. Connect the battery (5’ 9”) and motor (4’ 1”) leads. Connect the red

(Positive+) to the in-facing terminal (marked +) on the motor and the black

(Negative-) to the out-facing terminal (marked -) on the motor. Then

connect the red (Positive+) lead from the power switch to the positive (+)

terminal of the vehicles 12 volt battery. Connect the black (Negative -)

lead from the power switch to the negative (-) terminal of the battery.

(Fig.1 & Fig. 2) CAUTION – Batteries contain gases which are

flammable and explosive. Wear eye protection during installation and

remove all jewelry. Do not lean over battery while making connections.

5. Assemble the Clevis Hook to the cable. Pull and turn the clutch knob to

the “Off” position (Free-spooling). Pull out some cable from the drum.

Take off the pin from the Clevis Hook, connect the Clevis Hook to the

cable and mount the pin back to the Clevis Hook (Fig. 3 & Fig. 4)

6. Always use the Hand Saver when free-spooling and re-spooling the wire

rope. (Fig. 7) Using the Hand Saver will keeps your hands and fingers

away from the rotating drum.

7. Check for proper drum rotation. Pull and turn the clutch knob to the “off”

position (Free-spooling). Pull out some cable from the drum, then turn

the clutch knob to the “In” position to engage the gears. Press the cable

out button on the power switch. If the drum is turning and releasing more

cable then your connections are accurate. If the drum is turning and

collecting more cable then reverse the leads on the motor. Repeat and

check rotation.

Fig. 1 Fig. 2

Fig. 3 Fig. 4

Fig. 5 Fig. 6

Fig 7

SAFETY PRECAUTIONS

WARNING

WARNING – DO NOT EXCEED RATED CAPACITY.

WARNING – Intermittent use only.

WARNING - Do not use winch in lifting or moving or persons.

WARNING - A minimum of five wraps of cable around the drum barrel is

necessary for pulling and holding the rated load. The cable clamp is not

designed to hold the load without 5 wraps of cable around the barrel.

WARNING - Keep yourself and others a safe distance to the side of the

cable when under tension.

WARNING – The wire rope may break before the motor stalls. For heavy

loads at or near rated capacity, use a pulley block/snatch block to reduce

the load on the wire rope.

WARNING -Never step over a cable, or near a cable under load.

WARNING - Don’t move the vehicle to pull a load (towing) on the winch

cable. This could result in cable breakage.

WARNING Disconnect the remote control and battery leads when not in

use.

WARNING Do not exceed maximum pull rating. Avoid “shock loads” by

using the control switch intermittently to take up the slack in the wire

rope. “Shock loads” can far exceed the rate capacity for the wire rope

and drum.

WARNING- Do not exceeds maximum line pull ratings shown on the

tables.

WARNING-When re-spooling the cable, ensure that the cable spools in

the under-wind position with the cable entering the drum from the

bottom, not the top. To re-spool correctly, and while wearing gloves,

keep a slight load on the cable while pushing the remote button to draw

in the cable. Walk toward the winch not allowing the cable to slide

through your hands. Do not let your hands get within 12” of the winch

while re-spooling. Turn off the winch and repeat the procedure until a few

feet of cable is left. Disconnect the remote control and finish spooling by

hand by rotating the drum by hand with the clutch disengaged. Keep

hands clear of the fairlead and drum while the winch is under power.

Do not use as a hoist. Do not use for overhead lifting.

Failure to heed these warnings may result in personal injury and/or

property damage.

CAUTION - Use gloves to protect hands when handling the cable. Never

let the cable slide through your hands.

Apply blocks to the wheels of the vehicle when on an incline.

No modifications, alterations, or deviation to the winch are authorized by the

manufacturer and should not be made.

Duration of winching pulls should be kept as short as possible. If the motor

becomes uncomfortably hot to the touch, stop winching immediately and let

it cool down for a few minutes. Do not pull for more than one minute at or

near the rated load. CAUTION - If the motor stalls do not maintain power

to the winch. Electric winches are designed and made of intermittent use

and should not be used in constant duty applications.

CAUTION - Never release the free-spool clutch when there is a load on the

winch.

CAUTION - Use hand saver hook when handling the hook for spooling or

un-spooling the wire rope.

GENERAL TIPS FOR SAFE OPERATION

• The C20049 is rated at 2,000 lbs. capacity when spooling the first rope

layer on the drum. Overloads can damage the winch/motor/ or wire

rope. For loads over 1,000 lbs. we recommend the use of the pulley

block/snatch block to double the wire rope line. The will aid in two

ways: a) reduce the number or rope layers on the drum, as well as, b)

reduce the load on the wire rope by as much as 50%. When doubling

the line back to the vehicle, attach to the frame or other load bearing

part.

• The vehicle engine should be kept running during operation of the

winch to minimize battery drain and maximize power and speed of the

winch. If the winch is used for a considerable time with the engine off

the battery may be drained and too weak to restart the engine

• Get to know your winch before you actually need to use it. We

recommend that you set up a few test runs to familiarize yourself with

rigging techniques, the sounds your winch makes under various

loads, the way the cable spools on the drum, etc.

• Inspect the wire rope and equipment before each use. A frayed or

damaged rope shall be replaced immediately. Use only

manufacturer’s identical replacement rope with the exact

specifications.

• Inspect the winch installation and bolts to ensure that all bolts are

tight before each operation.

• Never connect the cable back to itself. This will cause cable damage.

Always use a snatch block, sling or chain of suitable strength as

shown in the illustrations.

• Store the remote control inside your vehicle in a place that it will not

be damaged.

• Any winch that appears to be damaged in any way, is found to be

worn, or operates abnormally SHALL BE REMOVED FROM SERVICE

UNTIL REPAIRED. It is recommended that the necessary repairs be

made by a manufacturer’s authorized repair facility.

• Pull only on areas of the vehicle as specified by the vehicle

manufacturer.

• Only attachments and/or adapters supplied by the manufacturer shall

be used.

RIGGING TECHNIQUES

Self Recovery

Locate a suitable anchor such as a strong tree trunk or boulder.

Always use a sling as an anchor point. CAUTION Do not attach

the clevis hook back onto the cable as this could cause damage to

the cable.

As shown in Fig 3.1

Do not winch from an acute angle as the wire rope will pile up on

one side of the drum causing damage to wire rope and the winch.

Fig 3.2

Short pulls from an angle can be used to straighten the vehicle.

Long pulls should be done with the wire rope at a 90° angle to the

winch/vehicle.

When pulling a heavy load, place a blanket or jacket over the wire

rope five or six feet from the hook. In the event of a broken cable it

will dampen the snap back. For additional protection open the

hood of the vehicle as shown in Fig 3.3

Fig 3.1

Fig 3.2

Fig 3.3

For pulls over 1,000lbs, we recommend the use of the snatch

block/pulley block to double line the wire rope. Fig 3.4

This reduces the load on the winch and the strain on the rope by

approximately 50%.

WARNING - Never use your winch for overhead hoisting or for

lifting people or moving people.

WINCHING TECHNIQUES A-Z

a. Take time to asses your situation and plan your pull.

b. Put on gloves to protect your hands.

c. Disengage the clutch to allow free-spooling and also save battery

power.

d. Attach the hand saver hook to the clevis hook.

e. Pull out the wire rope to your desired anchor point using the hand

saver hook.

f. Secure the clevis hook to the anchor point: Sling, chain or snatch

block. Do not attach the hook back onto the wire rope.

g. Engage the clutch.

h. Connect the remote control to the winch.

i. Start your engine to ensure power is being replenished to the

battery.

j. Power in the wire rope guiding the wire under tension to draw up

the slack in the wire. Once the wire is under tension stand well

clear. Never step over the wire rope.

k. Double check your anchors and make sure all connections are

secure.

Fig 3.4

Fig 3.5

l. Inspect the wire rope. Make sure there are at least 5 wraps of wire

rope around the winch drum.

m. Drape a blanket or jacket over the wire rope approximately 5 to 6

feet from the hook. Open the hood for added protection.

n. Clear the area. Make sure all spectators all well back and that no

one is directly in front or behind the vehicle or anchor point.

o. Begin winching. Be sure that the wire rope is winding evenly and

tightly around the drum. The vehicle that is being winched can be

slowly driven to add assistance to the winching process. Avoid

shock loads; keep the wire rope under tension.

p. The vehicle to be winched should be placed in neutral and the

emergency brake released. Only release the brake pedal when

under full tension. Avoid shock loads to the winch. This can

damage the winch, rope and vehicle.

q. The winch is meant for intermittent use. Under full load with a

single line rig do not power in for more than a minute without

letting the motor cool down for a few minutes and then resume the

winching operation.

r. The winching operation is complete once the vehicle is on stable

ground and is able to drive under its own power.

s. Secure the vehicle. Be sure to set the brakes and place the vehicle

in park.

t. Release the tension on the wire rope. The winch is not meant to

hold the vehicle for long periods of time.

u. Disconnect the wire rope from the anchor.

v. Rewind the wire rope. Make sure that any wire already on the drum

has spooled tightly and neatly. If not, draw out the wire and re-

spool from the point where the rope is tight.

w. Keep your hands clear of the winch drum and fairlead as the wire

rope is being drawn in.

x. Secure the hook and hook strap.

y. Disconnect the remote control and store in a clean, dry place.

z. Clean and inspect connections and mounting hardware for next

winching operation.

MAINTAINNENCE

1. Periodically check the tightness of mounting bolts and electrical

connections. Remove all dirt or corrosion and always keep clean.

2. Do not attempt to disassemble the gear box. Repairs should be done

by the manufacturer or an authorized repair center.

3. The gear box has been lubricated using a high temperature lithium

grease and is sealed at the factory. No internal lubrication is required.

REPLACING THE WIRE ROPE

1. If the wire rope has become worn or is beginning to show signs of

strands breaking it must be replaced before being used again. To do

this, remove the defective rope by free spooling. Remove the

M5x5mm bolt on the drum and release the rope.

2. Insert the end of the new rope and secure the M5 x 5 mm bolt tightly.

3. Engage the clutch and re-spool the new rope on the drum keeping

tension on the rope as it spools. Ensure that the rope is respooling in

the under wind position.

WARNING - Only replace the wire rope with the identical replacement part

recommended by the manufacturer.

TROUBLE SHOOTING

SYMPTOM POSSIBLE CAUSE SUGGESTED ACTION

Motor does not

turn on

-Switch Assembly not

connected properly

-Loose battery cable

connections

-Solenoid malfunctioning

-Defective Switch

Assembly

-Defective motor

-Water has entered motor

-Insert Switch Assembly all the way into

the connector.

-Tighten nuts on all cable connections.

-Tap solenoid to loosen contacts. Apply

12 volts to coil terminals directly. A

clicking indicates proper activation.

-Replace Switch Assembly.

-Check for voltage at armature port with

Switch pressed. If voltage is present,

replace motor.

-Allow to drain and dry. Run in short

bursts without load until completely dry.

Motor runs but

Cable drum does

not turn

-Cam Ring (clutch) not

engaged

-Move Cam Ring to the “In” position. If

problem persists, a qualified technician

needs to check and repair.

Motor runs slowly

or without normal

power

-Insufficient current or

voltage

-Battery weak, recharge. Run winch with

vehicle motor running.

-Loose or corroded battery cable

connections. Clean, tighten, or replace.

Motor overheating

-Winch running time too

long

-Allow winch to cool down periodically.

Motor runs in one

direction only

-Defective or stuck

solenoid

-Defective Switch

Assembly

-Tap solenoid to loosen contacts.

-Repair or replace solenoid.

-Replace Switch Assembly.

WINCH ASSEMBLY DRAWING

3

4

6

5

1

2

25

26

27

7

8

9

10

11

12

13

14

15

17

18

19

20

21

22

23

24

28

16

WINCH PARTS LIST

No. Part # Qty Description

1 200100 1 Motor

2 200200 1 Stationary Gear Housing Assembly

3 200300 1 Gear Carrier Assembly

4 200001 1 T-Series Rotator Gear

5 200002 1 Drum Support Plate

6 200003 4 Spring Washer Φ4 & Pan Head Screw M4 x 12

7 200004 1 Drum Support Bushing

8 200400 1 Clutch Assembly

9 200005 1 Spring

10 200006 1 Drum Assembly

11 200007 1 Screw M5 x 5

12 200008 1 T-Series Bushing

13 200009 1-2 Thick Flat Washer

14 200010 2 Hex Flange Nut M5

15 200011 1 T-Series Base Plate Assembly

16 200012 1 Tension Plate

17 200500 1 T-Series F/W Knob Assembly

18 200013 1 Elastic Pin 2.5 x 14

19 200014 2 Cap Screw M6 x 16

20 200015 2 Screw M5 x 10

21 200016 2 Screw M8 x 30

22 200017 2 Nut Φ8

23 200018 2 Washer -Flat Φ8

24 200019 2 Nut M8

25 200020 1 Hand Saver Bar

26 200600 1 Switch Assembly

27 200700 1 Cable Assembly

28 200800 1 Pulley Block

# C20049

Rated line pulls: 2000lbs (906 kgs)

Gear reduction ratio: 153:1

Motor: Permanent magnet DC 12V motor with 0.7hp

output

Overall dimensions: 11.2 “(L) x 4.13” (W) x 4.13” (H)

285 (L) x 110 (W) x 105 (H) mm

Drum size: 1.24” (D) x 2.88” (L)

31.5(D) x 73 (L) mm

Cable: 49’ (L) of 5/32” (D)

15m (L) of 4mm (D)

Net weight: 16 lbs

7.25 kgs

Line speed and Motor current (First layer)

Line Pull

Line Speed

Ft/min (m/min)

Motor Current

Amps

lb (kgs) 12V DC 12V DC

0 18(5.4) 12

500(227) 9.2(2.8) 25

1000(454) 7.5(2.3) 40

1500(680) 5.9(1.8) 60

2000(906) 3.3(1.3) 90

Line pull and Cable capacity

Layer of

Cable

Rated line pull per Layer

lb (kgs)

Cable Capacity per Layer

ft (m)

1 2000(906) 6.5(2.0)

2 1630(740) 14.0(4.3)

3 1380(620) 22.0(6.8)

4 1190(540) 31.0(9.5)

5 1050(480) 41.0(12.5)

6 940(420) 49.0(15.0)

Warranty

Champion Power Equipment

1 YEAR LIMITED WARRANTY

Effective September 1, 2006. Replaces all undated warranties and all warranties dated before September 1, 2006

Warranty Qualifications

Champion Power Equipment (CPE) will register this

warranty upon receipt of your Warranty Registration

Card and a copy of your sales receipt from one of

CPE's retail locations as proof of purchase.

Please submit your warranty registration and your

proof of purchase within ten (10) days of the date of

purchase.

Repair/Replacement Warranty

CPE warrants to the original purchaser that the

mechanical and electrical components will be free of

defects in material and workmanship for a period of

one (1) year from the original date of purchase (90

days for commercial & industrial use). Transportation

charges on product submitted for repair or

replacement under this warranty are the sole

responsibility of the purchaser. This warranty only

applies to the original purchaser and is not

transferable.

Do not return the unit to the place of

purchase

Contact CPE's Technical Service and CPE will

troubleshoot any issue via phone or e-mail. If the

problem is not corrected by this method, CPE will, at

its option, authorize evaluation, repair or replacement

of the defective part or component at a CPE Service

Center. CPE will provide you with a case number for

warranty service. Please keep it for future reference.

Repairs or replacements without prior authorization,

or at an unauthorized repair facility, will not be

covered by this warranty.

Warranty Exclusions

This warranty does not cover the following repairs

and equipment:

Normal Wear

Winches need periodic parts and service to perform

well. This warranty does not cover repair when

normal use has exhausted the life of a part or the

equipment as a whole.

Installation, Use and Maintenance

This warranty will not apply to parts and/or labor if

this winch is deemed to have been misused, neglected,

involved in an accident, abused, loaded beyond the

winch’s limits, modified, installed improperly or

connected incorrectly to any component. Normal

maintenance such as spark plugs, air filters,

adjustments, fuel system cleaning and obstruction

due to buildup is not covered by this warranty.

Other Exclusions

This warranty excludes:

• Cosmetic defects such as paint, decals, etc.

• Wear items such as filter elements, o-rings, etc.

• Accessory parts such as starting batteries, and

storage covers.

• Failures to due acts of God and other force majeure

events beyond the manufacturer’s control.

• Problems caused by parts that are not original

Champion Power Equipment parts.

Limits of Implied Warranty and

Consequential Damage

Champion Power Equipment disclaims any obligation

to cover any loss of time, use of this product, freight,

or any incidental or consequential claim by anyone

from using this winch. THIS WARRANTY IS IN LIEU

OF ALL OTHER WARRANTIES, EXPRESS OR

IMPLIED, INCLUDING WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE

A unit provided as an exchange will be subject to the

warranty of the original unit. The length of the

warranty governing the exchanged unit will remain

calculated by reference to the purchase date of the

original unit.

This warranty gives you certain legal rights which may

change from state to state. Your state may also have

other rights you may be entitled to that are not listed

within this warranty.

Contact Information

Address

Champion Power Equipment, Inc.

Customer Service

10006 Santa Fe Springs Rd.

Santa Fe Springs, CA 90670

Customer Service

Mon – Fri 8:30 AM – 5:00 PM (PST/PDT)

Toll Free: 1-877-338-0999

Fax no.: 1-562-236-9429

Technical Service

Mon – Fri 8:30 AM – 5:00 PM (PST/PDT)

Toll Free: 1-877-338-0999

tech@championpowerequipment.com

INTRODUCTION

Nous vous félicitons d’avoir choisi un treuil Champion. Nos treuils sont conçus

et fabriqués selon des normes rigoureuses. Aussi, leur usage et leur entretien

appropriés devraient vous assurer des années de loyaux services.

AVERTISSEMENT - Lire, apprendre et observer toutes les directives avant

de faire fonctionner ce dispositif. Le fait de ne pas respecter les instructions

pourrait entraîner des blessures corporelles ou des dommages matériels.

Ce treuil peut développer une formidable force de traction et pourrait causer

des dommages matériels, des blessures graves et même la mort s’il est utilisé

de façon irresponsable ou inadéquate. En parcourant ce manuel, vous trouverez

les symboles ci-dessous qui représentent des mises en garde et des

avertissements. Porter une attention toute spéciale aux notes accolées à ces

symboles, car elles ont été rédigées à des fins de sécurité. Enfin, l’utilisation

sécuritaire de cet appareil dépend d’abord de l’utilisateur.

Indique une situation potentiellement dangereuse qui, faute de

l’éviter, pourrait entraîner des blessures légères à modérées. On

l’utilise également comme mise en garde contre certaines

pratiques non sécuritaires.

Indique une situation potentiellement dangereuse qui, faute de l’éviter,

pourrait entraîner des blessures graves et même la mort.

ATTENTION

ACCESSOIRES COMPRIS AVEC LE TREUIL

DESCRIPTION QUANTITÉ

1. Treuil équipé et câble métallique 1

2. Boulons d’assemblage M8 x 30 2

3. Rondelles freins 2

4. Rondelles plates 2

5. Écrous M8 2

6. Moufle / Poulie coupée 1

7. Crochet à chape et goupille 1

8. Cordon / Interrupteur d’alimentation 1

9. Broche protège-mains 1

ACCESSOIRES NÉCESSAIRES

NON COMPRIS AVEC LE TREUIL

Gants – Pour manipuler le câble métallique et la sangle du crochet.

Chape / Manille en D – Pour relier la poulie coupée à la sangle d’ancrage.

Sangle d’ancrage / Chaîne – Les sangles d’ancrage protègent les arbres. Elles

sont faites de nylon de haute qualité qui offre une résistance élevée à la tension

(5 000 à 10 000 lb).

Couverture lourde – Pour placer sur le câble afin d’absorber l’énergie si ce

dernier venait à se rompre.

ASSEMBLAGE DU TREUIL

1.

1. Ce treuil CPE 2 000 lb présente une configuration à boulons très répandue

dans cette catégorie d’appareils. De nombreux nécessaires d’assemblage

comportant cette configuration sont offerts pour les VTT et profilés de fixation

les plus populaires. Si on ne parvient pas à trouver un nécessaire d’assemblage

dans une région, communiquer avec CPE pour obtenir les coordonnées du

détaillant le plus près.

2. Quel que soit le nécessaire d’assemblage utilisé, se placer sur une surface

plane pour procéder à l’assemblage du treuil afin que ses trois sections

principales, soit le moteur, le tambour et le système d’engrenage, se retrouvent

parfaitement alignés. Un alignement approprié permettra une distribution

uniforme de l’ensemble de la charge.

3. N’utiliser que les boulons M8 x 30, rondelles et écrous compris avec le treuil.

4. Relier les câbles du moteur à la batterie. Connecter le rouge (positif) à la

borne tournée vers l’extérieur du moteur et le noir (négatif) à la borne tournée

vers l’intérieur du moteur. Ensuite, connecter le câble rouge (positif) de

l’interrupteur à la borne positive (+) de la batterie 12 volts du véhicule, puis le

noir (négatif) à sa borne négative (-) (Fig. 1 et 2).

5. Fixer le crochet au câble. Tirer et tourner le bouton d’embrayage à la position

« Off » (roulement libre). Sortir un bout de câble du tambour. Retirer la goupille

du crochet à chape, passer l’œil du câble dans la chape, puis remettre la

goupille en place (Fig. 3 et 4).

6. Toujours utiliser la broche protège-mains au moment de bobiner le câble à la

main ou de le rembobiner (Fig. 7). Elle permet de garder mains et doigts à

bonne distance du tambour rotatif.

La page charge ...

Champion Power Equipment C20049 Le manuel du propriétaire

Ce manuel convient également à

Champion Power Equipment C20049 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents