Greenheck SP-L, Wall/Ceiling Exhaust Fan Manuel utilisateur
- Catégorie
- Ventilateurs ménagers
- Taper
- Manuel utilisateur
®
Document 481174
Model SP-L
Wall/Ceiling Exhaust Fan
Wall/Ceiling Exhaust Fan 1
®
Installation, Operation and Maintenance Manual
Please read and save these instructions for future reference. Read carefully before attempting to assemble, install,
operate or maintain the product described. Protect yourself and others by observing all safety information. Failure
to comply with these instructions will result in voiding of the product warranty and may result in personal injury
and/or property damage.
Model SP-L is a direct drive wall/ceiling exhaust
fan designed for clean air exhaust applications.
Installation options include wall mount frame
construction and ceiling mounts. Accessories are
available, see catalog and CAPS for selections.The
motor is designed for continuous use and is thermally
protected. A backdraft damper is standard on the
outlet of the fan to stop backdrafts when the fan is not
in use and a grille with mounting screws is provided
for quiet, rattle-free operation. Capacities range
from 50-80 cfm and 0.75 in. wg. The SP-L is UL/cUL
Listed for above bathtub or shower with GFCI branch
protected circuit.
General Safety Information
Only qualified personnel should install this fan.
Personnel should have a clear understanding of these
instructions and should be aware of general safety
precautions. Improper installation can result in electric
shock, possible injury due to coming in contact with
moving parts, as well as other potential hazards.
1. Follow all electrical and safety codes, as well as
the National Electrical Code (NEC) and the National
Fire Protection Agency (NFPA) where applicable.
Follow the Canadian Electrical Code (CEC) in
Canada.
2. The rotation of the wheel is critical. It must be free
to rotate without striking or rubbing any stationary
objects.
3. Motor must be securely and adequately grounded.
4. Verify the power source is compatible with the
equipment.
Wall/Ceiling Exhaust Fan2
®
WARNING
To reduce the risk of fire, electric shock, or injury
to persons, observe the following:
• Use this unit only in the manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
• Before servicing or cleaning unit, switch power off
at service panel and lock service disconnecting
means to prevent power from being switched
on accidentally. When the service disconnecting
means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the
service panel.
• Installation work and electrical wiring must be
done by qualified person(s) in accordance with all
applicable codes and standards, including fire-
rated construction.
• Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney) of
fuel burning equipment to prevent back drafting.
Follow the heating equipment manufacturer’s
guideline and safety standards such as those
published by the National Fire Protection
Association (NFPA), and the American Society
for Heating, Refrigeration and Air Conditioning
Engineers (ASHRAE) and the local code
authorities.
• When cutting or drilling into wall or ceiling, do not
damage electrical wiring or other hidden utilities.
• Acceptable for use over a bathtub or shower
when installed in a GFCI protected branch circuit.
• Never place a switch where it can be reached
from a tub or shower.
• Ducted fans must always be vented to the
outdoors.
• These fans are not recommended for cooking
exhaust applications. They are designed primarily
for low temperature, clean air applications only.
The diagram shows the minimum distance these
fans should be placed in relation to cooking
equipment.
• Install the fan at least 5 ft. (1.5 m) above the floor
and the fan must be installed above a counter or
major appliance that serves as a barrier.
• To reduce the risk of fire or electrical shock do
not use this fan with any solid state speed control
device.
CAUTION
• For general ventilating use only. Do not use to
exhaust hazardous or explosive materials and
vapors.
AVERTISSEMENT!
Pour réduire le risque d’incendie, de choc
électrique ou de blessure corporelle, respecter cd
qui suit:
• Utiliser cet appareil exclusivement comme prévu par
le fabricant. En cas de questions, communiquer avec
le fabricant à l’adresse ou au numéro de téléphone
figurant dans la garantie.
• Avant tout entretien ou nettoyage de l’appareil,
couper l’alimentation sur le tableau électrique et
verrouiller le dispositif de sectionnement pour
empêcher toute mise sous tension accidentelle.
Si le dispositif de sectionnement ne peut pas être
verrouillé, attacher un moyen de mise en garde bien
visible, tel qu’un panonceau, au tableau électrique.
• La pose et le câblage électrique doivent être
effectués par des personnes qualifiées en conformité
avec les codes et normes en vigueur, y compris pour
la résistance au feu du bâtiment.
• Une quantité d’air suffisante est nécessaire pour
la bonne combustion et l’extraction des gaz brûlés
par le conduit d’évacuation (cheminée) d’appareils
à combustible afin d’éviter le refoulement. Veiller
à suivre les indications du fabricant du matériel de
chauffe, les normes de sécurité telles que celles
publiées par la National Fire Protection Association
(NFPA) et l’American Society for Heating,
Refrigeration and Air Conditioning Engineers
(ASHRAE) et la réglementation en vigueur.
• Lors de la découpe ou du perçage de murs ou
plafonds, ne pas endommager les câbles électriques
et autres conduites masquées.
• Pose admissible au-dessus d’une baignoire ou
d’une douche sous réserve de raccordement à un
circuit de dérivation à protection GFCI (disjoncteur
différentiel).
• Ne jamais placer d’interrupteur à un emplacement à
portée d’une baignoire ou d’une douche.
• Les caissons d’extraction à gaine doivent toujours
être évacués vers l’extérieur.
• Ces caissons ne sont pas conseillés pour les
applications d’aspiration de vapeurs de cuisson. Ils
sont conçus essentiellement pour l’aspiration d’air
propre à basse température. Le schéma indique la
distance minimale de placement de ces caissons par
rapport à l’équipement de cuisson.
• Installer le caisson à au moins 1,5 m (5 pi) au-
dessus du sol et installer le caisson au-dessus d’un
comptoir ou d’un gros appareil qui fait office de
barrage.
• Pour réduire le risque d’incendie ou de choc
électrique, ne pas utiliser ce caisson avec un
quelconque dispositif de régulation de vitesse à
semi-conducteurs.
ATTENTION!
• À utiliser pour la ventilation générale uniquement. Ne
pas utiliser pour l’aspiration de matières et vapeurs
dangereuses ou explosives.
Read and save these instructions Veuillez lire et conserver ces instructions
Wall/Ceiling Exhaust Fan 3
®
Receiving
Upon receiving the product, check the bill of lading
to ensure all items were received. Inspect each crate
for shipping damage before accepting delivery. Alert
the carrier of any damage detected. The customer will
make a notation of damage (or shortage of items) on
the delivery receipt and all copies of the bill of lading
which is countersigned by the delivering carrier. Any
physical damage to the unit after acceptance is not
the responsibility of Manufacturer.
Unpacking
Verify that all required parts and the correct quantity
of each item have been received. If any items are
missing, report shortages to your local representative
to arrange for obtaining missing parts. Sometimes it
is not possible that all items for the unit be shipped
together due to availability of transportation and truck
space. Confirmation of shipment(s) must be limited to
only items on the bill of lading.
Storage
Fans are protected against damage during shipment.
If the unit cannot be installed and operated
immediately, precautions need to be taken to prevent
deterioration of the unit during storage. The user
assumes responsibility of the fan and accessories
while in storage. The manufacturer will not be
responsible for damage during storage. These
suggestions are provided solely as a convenience
to the user.
The ideal environment for the storage of fans and
accessories is indoors, above grade, in a low humidity
atmosphere which is sealed to prevent the entry of
blowing dust, rain or snow. Temperatures should be
evenly maintained between 30° to 110°F (-1° to 43°C)
(wide temperature swings may cause condensation
and “sweating” of metal parts). All accessories
must be stored indoors in a clean, dry atmosphere.
Remove any accumulations of dirt, water, ice or snow
and wipe dry before moving to indoor storage. To
avoid “sweating” of metal parts allow cold parts to
reach room temperature. To dry parts and packages,
use a portable electric heater to get rid of any
moisture buildup. Leave coverings loose to permit air
circulation and to allow for periodic inspection.
The unit should be stored at least 3½ in. (89 mm) off
the floor on wooden blocks covered with moisture
proof paper or polyethylene sheathing. Aisles between
parts and along all walls should be provided to permit
air circulation and space for inspection.
Inspection and Maintenance
During Storage
While in storage, inspect fans once per month. Keep a
record of inspection and maintenance performed.
If moisture or dirt accumulations are found on parts,
the source should be located and eliminated.
Removing From Storage
As fans are removed from storage to be installed
in their final location, they should be protected and
maintained in a similar fashion until the fan equipment
goes into operation.
Wall/Ceiling Exhaust Fan4
®
5. Snap the metal discharge on to the fan housing
as shown in Figure 4-A and 4-B. Using provided
screw, secure the outlet to the housing
Figure 4-C.
1. For best performance, choose a location with
the shortest possible duct run and minimum
number of elbows. Do not mount near cooking
equipment. As shown in Figure 1.
Installation
4. Remove a wiring knockout from junction box by
bending it back and forth to break tabs.
See Figure 3.
IMPORTANT
Installation, troubleshooting and parts replacement is to be performed only by qualified personnel. Consult and
follow all applicable national, state and local codes. They will supercede this document.
Figure 3
7/8-inch Knockouts
Junction Box
Metal Discharge
Figure 4-A
Figure 4-B
Figure 4-C
Figure 2
Mounting Bracket
3. Fold down mounting brackets so they are
perpendicular to the fan housing at a 90 degree
angle as shown in Figure 2.
2. See fan nameplate for power ratings. Check
that they are compatible with power ratings in
building.
45° 45°
Do not install
fan in this area
Figure 1
Wall/Ceiling Exhaust Fan 5
®
6. Install fan into wall or ceiling using one of the
following methods:
Wall Mount Frame Construction
a. Position between studs with the discharge
pointing up.
b. Fasten fan to studs using screws (supplied by
others) as shown in Figure 5.
7. For wiring the fan remove wiring cover. Bring field
wiring into the junction box. Using proper wiring
connectors, wire the fan as shown in Figure 7.
Push all wiring back into the fans junction box
and replace wiring cover.
Ceiling Mount Hanging Installation
a. Use Greenheck’s optional vibration isolation kit.
Using the fold down mounting brackets and
1/4-20 threaded rod (by others) to hang unit as
shown in Figure 6.
8. Connect ductwork by squeezing ductwork and
sliding over the fans discharge, see Figure 8.
Attach the ductwork to the discharge by using a
clamp and seal with approved tape.
Figure 5
Figure 7
Figure 8
1/4 - 20 Threaded Rod
Mounting Bracket
Figure 6
NOTE
A 4-inch round rigid metal outlet duct is
recommended for best results.
Wall/Ceiling Exhaust Fan6
®
9. Attach the grille after the drywall is installed. Use
the two screws provided to screw the grille into
the housing. Make sure not over tightening as
this will damage the grille. Slide attached screw
covers over the attachment screws to conceal.
See Figure 9.
10. Turn on power and check fan operation.
11. Optional: A cardboard insert is supplied with
every fan to protect the inner components of the
fan during the construction process. This insert
is found between the grille and the housing in the
package. See Figure 10.
Figure 9
Screw Covers
Cardboard
Insert
Figure 10
Wall/Ceiling Exhaust Fan 7
®
NOTE
• A 4-inch round rigid metal outlet duct is recommended for best results.
• The ducting from this fan to the outside of the building has a strong effect on the air flow, nosie and energy
use of the fan. Use the shortest, straightest duct routing possible for best performance, and avoid installing
the fan with smaller ducts than recommended. Insulation around the ducts can reduce energy loss and inhibit
mold growth. Fans installed with existing ducts may not achieve their rated air flow.
*Purchase separately.
INSULATION*
(Place around and over Fan Housing.)
ROOF CAP*
(with built-in damper)
FAN HOUSING
POWER CABLE*
ROUND
DUCT*
ROUND
ELBOWS*
Seal gaps around
Housing.
Seal duct joints
with tape.
OR
Keep duct runs short.
WALL CAP*
(with built-in damper)
General Maintenance Suggestions
Model SP-L wall/ceiling exhaust fans require very little maintenance. But since small problems over time left
unchecked could lead to loss of performance or early motor failure, we do recommend that the unit be inspected
periodically (once or twice a year).
The fan motor and wheel should be checked for dust and dirt accumulations. Dirt buildup can lead to loss of
performance and motor overheating. Cleaning can be accomplished by brushing off any dust that may have
accumulated.
Typical Residential Installation
481174 • SP-L, Rev. 2, July 2016 Copyright 2016 © Greenheck Fan Corporation8
As a result of our commitment to continuous improvement, Greenheck reserves the right to change specifications
without notice.
Specific Greenheck product warranties are located on greenheck.com within the product area tabs and in the
Library under Warranties.
Greenheck’s Centrifugal Ceiling and Cabinet Exhaust Fans catalog provides additional information describing the equipment,
fan performance, available accessories, and specification data.
®
Phone: 715.359.6171 • Fax: 715.355.2399 • Parts: 800.355.5354 • E-mail: [email protected] • Website: www.greenheck.com
Our Commitment
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Greenheck SP-L, Wall/Ceiling Exhaust Fan Manuel utilisateur
- Catégorie
- Ventilateurs ménagers
- Taper
- Manuel utilisateur
dans d''autres langues
Documents connexes
-
Greenheck 474680 Ceiling Exhaust and Inline Fans Mode d'emploi
-
-
-
-
-
-
