Fulgor F4GK36S1 Guide d'installation

F4GK24*1

F4GK30*1

F4GK36*1

F4GK42*1

EN INSTALLATION INSTRUCTIONS

FR INSTRUCTIONS D’INSTALLATION

ES INSTRUCCIONES DE INSTALLACIÓN

GAS COOKTOP

PLAQUE DE CUISSON GAZ

PLACA DE COCCIÓN DE GAS

Dear Customer,

Thank you for purchasing a Fulgor Milano product. Fulgor Milano is

committed to excellence and our signature technologies provide you with

professional tools for your kitchen. One of our central philosophies is

continuous investment in research that is rooted in developing life enhancing

technology. Our goal is to deliver products that are worthy of your family

recipes and that will breathe life into your kitchen, the heart of your home.

We invite you to enjoy your new Fulgor Milano product with same amount

of care and attention that we have put into creating it.

Your Life | Our Passion

EN

1

TABLE OF CONTENTS PAGE

1 - Special Warnings 2

Before Starting Installation 2

2 - Product Dimensions and Cutout Requirements 3

Important Preparation Suggestions 3

Mobile Home Installation 6

3 - Cooktop Installation 7

4 - Gas Requirement 9

Gas Connection 10

Pressure Testing 12

Pressure Test Method 12

5 - Electrical Requirements 13

General Information 13

Electrical Connection 13

Electrical Requirements 13

6 - Conversion for LP or NG Gas 15

Converting Appliance for Use with LP Gas 15

Replace injector on (one ring ﬂame burners) 15

Replace injectors on (two rings ﬂame burner) 15

Converting Appliances for Use with NG Gas 16

Pressure regulator conversion 16

Injectors position 17

Low Flame Adjustment 18

Electric gas ignition 19

The Burner Flames 19

IMPORTANT: Save these instructions for the local electrical

inspector use.

INSTALLER: Please leave this manual with owner for future

reference.

OWNER: Please keep this manual for future reference.

Pay attention to these symbols present in this manual:

DANGER

You can be killed or seriously injured if you don’t

IMMEDIATELY follow instructions.

WARNING

• This is the safety alert symbol. This symbol alerts you to

potential hazards that can kill or hurt you and others.

• You can be killed or seriously injured if you don’t follow

these instructions.

READ AND SAVE THESE INSTRUCTIONS.

To installer:

Leave these instructions with the appliance.

To customer:

Retain these instructions for future reference.

WARNING

• If the information in this manual is not followed exactly,

a ﬁre or explosion may result in personal injury or

death.

• Do not store or use gasoline or other ﬂammable

vapours and liquids in the vicinity of this or any other

appliance.

EN

2

1 - Special Warnings

IMPORTANT

Please read all instructions before using this appliance.

Proper installation is your responsibility. Have a qualiﬁed

technician install this cooktop.

IMPORTANT

• Observe all governing codes and ordinances.

• Write down the model and serial numbers before

installing the cook top. Both numbers are on the serial

rating plate located on bottom of cooktop box.

Before Starting Installation

• Check location where cooktop will be installed. The

location should be away from strong drafty areas, such

as windows, doors and strong heating vents or fans.

• Electrical grounding is required. See “Electrical

Requirements”

• Assure that electrical installation is adequate and in

conformance with National Electrical Code, ANSI/NFPA

70 - latest edition**, or Canadian Electrical Code, part

1 C22.1 (latest edition)*** and all local codes and

ordinances.

• Assure that gas connection conforms with local codes and

ordinances. In the absence of local codes, installations

must conform with American National Standard, National

Fuel Gas Code ANSI Z223.1/NFPA 54 - latest edition**

The Natural Gas and Propane Installation Code, CSA

149.1 or CSA B149.2 latest edition***.

Copies of the standards listed may be obtained from:

** National Fire Protection Association One Batterymarch

Park Quincy, Massachusetts 02269

*** CSA International 8501 East Pleasant Valley Rd.

Cleveland, OH 44131-5575

NOTE: This cooktop is manufactured for use with Natural

gas or Propane.

To convert to LP (propane) or NG (natural gas),

see instruction in the gas conversion kit provided

in literature package. Proper gas supply connection

must be available. See gas supply requirements.

WARNING

BEFORE CONNECTING THE APPLIANCE ON THE

GAS LINE SUPPLY, ENSURE THAT ITS GAS SETTING IS

APPROPRIATE.

THE TYPE OF GAS ADJUSTED AND SHIPPED FROM

THE FACTORY IS INDICATED ON THE RATING PLATE

LOCATED ON BOTTOM OF THE BURNER BOX.

EN

3

2 - Product Dimensions and Cutout Requirements

Important Preparation Suggestions

1. Chamfer all exposed edges of decorative laminate to prevent damage from chipping.

2. Radius corners of cutout and ﬁle to Insure smooth edges and prevent corner cracking. Recommend 1/4”or 3/8” diameter drill

In each corner.

3. Rough edges, inside corners which have not been rounded and forced ﬁts can contribute to cracking of the countertop

laminate.

PRODUCT DIMENSIONS

24”

2-15/16”

(7,4 cm)

20-1/16” (51 cm)

24-1/2” (62 cm)

30”

30” (76 cm)

2-15/16”

(7,4 cm)

20-1/16” (51 cm)

36”

36” (91 cm)

2-15/16”

(7,4 cm)

20-1/16” (51 cm)

44”

44” (112 cm)

16-3/4” (42,5 cm)

2-15/16”

(7,4 cm)

EN

4

7-5/8 “ (19,3 cm)

86

5-11/16 “ (14,4 cm)

CUTOUT DIMENSIONS

CUT OUT

WIDTH A B C D

24” MIN. 23-1/2” ( 59,7 cm)

MAX. 23-5/8” ( 60,0 cm) MIN. 19-5/16” (49,0 cm)

MAX. 19-3/8” (49,3 cm) 2-1/2” ( 6,35 cm) MIN. 3” (7,62 cm)

30” MIN. 29” ( 73,7 cm)

MAX. 29-1/8” ( 74,0 cm) MIN. 19-5/16” (49,0 cm)

MAX. 19-3/8” (49,3 cm) 2-1/2” ( 6,35 cm) MIN. 3” (7,62 cm)

36” MIN. 34-7/8” ( 88,6 cm)

MAX. 35” ( 88,9 cm) MIN. 19-5/16” (49,0 cm)

MAX. 19-3/8” (49,3 cm) 2-1/2” ( 6,35 cm) MIN. 3” (7,62 cm)

44” MIN. 43-1/8” (109,6 cm)

MAX. 43-1/4” (109,9 cm) MIN. 15-15/16” (40,5 cm)

MAX. 16-1/16” (40,8 cm) 4” (10,16 cm) MIN. 3” (7,62 cm)

EN

5

CUTOUT REQUIREMENTS

A13” (33 cm) Depth of unprotected overhead cabinets.

B

24” (61.0 cm) MIN. (Model 24”)

30” (76.2 cm) MIN. (Model 30“).

36” (91.4 cm) MIN. (Model 36”).

44” (106.7 cm) MIN. (Model 44”).

C18” (47.7 cm) MIN. Height from countertop to nearest cabinet on either side of unit.

D30” (76.2 cm) MIN. (see Note* Clearance from countertop to unprotected overhead surface. )

E5” (12.7 cm) min Clearance from cut out to side wall on the left and right of the unit.

FFrom the back corner of cut-out to hole center 2-9/32” (5.8 cm).

GFrom the right corner of cut-out to hole center 2-19/32” (6.6 cm).

HFrom the back corner of cut-out to hole center 2-9/32 ” (5.8 cm). Opening with oven under cooktop.

IFrom the top of countertop to hole center 4-25/32 ” (12.2 cm). Opening with oven under cooktop.

LElectric outlet from bottom of counter top and adjacent to the cabinet side 12” (30.5 cm).

-Hole 1-1/5” (3 cm).

* NOTE:

- If cabinet has a drawer, a 5-1/4”(13,35 cm) depth clearance from the top of the countertop to the top of the drawer (or

other obstruction) in base cabinet is required. The drawer depth may need to be shortened to avoid interfering with the

regulator.

- 24” (61 cm) min. clearance if bottom of wood or metal cabinets is protected by not less than 1/4” (0.6 cm) ame

retardant millboard covered with not less than No. 28 MSG sheet steel 0.015” (0.04 cm) stainless steel, or 0.024”

(0.06 cm) aluminium or 0.020” (0.05 cm) copper. 30” (76.2 cm) min. clearance between top of cooking platform and

bottom of unprotected wood or metal cabinet.

- Min. 30” (76.2cm) Minimum to combustibles when no ventilation hood is present. If installing with an overhead vent

hood, also check hood speciﬁcations for minimum required clearances.

EN

6

We recommend to that you consider the minimum dimension

of cut-out size in the case of new installation.

WARNING

The appliance should not be installed with a ventilation

system that blows air downward toward the range.

This type of ventilation system may cause ignition and

combustion problems with the gas cooking appliance

resulting in personal injury or unintended operation.

Mobile Home Installation

The installation of this cooktop must conform to the

Manufactured Home Construction and Safety Standards,

Title 24 CFR, Part 3280 (formerly the Federal Standard for

Mobile Home Construction and Safety;

Title 24 HUD part 280); or when such standard is

not applicable, the Standard for Manufactured Home

Installations (Manufactured Home Sites, Communities and

Setups), ANSI A225.1 - latest edition, or with local codes.

In Canada, the installation of this cooktop must conform

with the current standards CAN/CSA-Z240 - latest edition,

or with local codes.

IMPORTANT

• For solid surface material installations such as Surel™

and Corian®, consult with solid surface manufacturer.

Apply heat reﬂective tape such as Scotch® Aluminum

Foil Tape #425 or #427 around the cutout so that it

folds over on the top and sides.

• DO NOT WRAP THE TAPE UNDERNEATH THE

COOKTOP.

• Be sure the tape extends beyond the outermost ﬂange

of the cooktop. All corners should be covered with

tape.

SOLID SURFACE COUNTERTOP INSTALLATION

EN

7

WARNING

• Excessive Weight Hazard

Use two or more people to move and install cooktop.

Failure to do so can result in back or other injury.

• Cut Hazard

Beware of sharp edges. Use the polystyrene ends when

carrying the product. Failure to use caution could result in

minor injury or cuts.

• Always consult the countertop manufacturer for speciﬁc

instructions.

• Ensure the countertop is square and level and ensure no

structural members interfere with space requirements.

• Prepare the cut-out according to the instructions (see cut-

out dimensions).

• Make sure the wall coverings, countertop and cabinets

around the cooktop can withstand heat (up to 200 °F).

TOOLS YOU WILL NEED

Step 1

Remove packaging materials and literature package from

the cooktop before beginning installation.

Remove Installation Instructions from literature pack and

read them carefully before you begin.

PARTS

COOKTOP

GRID

CARDBOARD

MANUAL

GASKET

GAS CONVERSION KIT

GAS CONNECTION KIT

SIMMER PLATE (if present)

WOK RING (if present)

POT ADAPTER (if present)

PRESSURE

REGULATOR

Step 2

Before installing apply the foam tape.

A tape is provided to seal the cooktop edges to the

countertop. Apply tape near inner underside cooktop edge.

Use tape around the entire cooktop perimeter.

Cut off excess where tape butt ends.

3 - Cooktop Installation

EN

8

Step 3

Insert the cooktop centered into the cutout opening.

Make sure the front edge of the counter top is parallel to

the cooktop. Make ﬁnal check that all required clearances

are met.

Step 4

Four clamp brackets are provided with your unit.

After cooktop has been installed into the countertop, install

the brackets on the burner box as shown in ﬁgure.

Install the clamp brackets on the front and back of the

burner box bottom (if the cabinet construction does not

provide clearance for installing brackets at the burner box

front back install the clamp brackets on the lateral position

of burner box).

step A place the clamping screws into brackets

step B attach brackets by using the attachment screws on the

selected location of burner box, tighten screws just enough

to hold brackets in place step C position brackets so that

they are with the clamp screw in contact with the counter

top bottom

step D tighten attachment screws securely.

step E check that the front edge of the cooktop is parallel to

the front edge of the countertop tighten the screw clamping

against the countertop.

DO NOT OVER TIGHTEN

EN

9

A QUALIFIED SERVICE MAN OR GAS APPLIANCE INSTALLER

MUST MAKE THE GAS SUPPLY CONNECTION.

Leak testing of the appliance shall be conducted by the

installer according to the instructions given.

You must install the supplied connection parts seen here in

this conﬁguration to the main gas manifold on the appliance.

Issues arising from a failure to do so will not be covered by

warranty.

Do not install the pressure regulator backwards as the gas will

not ﬂow correctly. Check that the arrow on the back points in

the direction of gas ﬂow.

Parts required for connection from gas supply to regulator are

the responsibility of the installer / owner

Appliance

pressure regulator Flare union

adaptor Gasket

Appliance

ATTENTION

Use Teﬂon tape rated for gas applications at all threaded

connections.

Do not overtighten the connection at the manifold or you

could damage the gasket causing a leak.

WARNING

If the line pressure supplying the appliance pressure

regulator exceeds 14 inches W.C. (any gas), an external

regulator must be installed in the gas line ahead of the

appliance regulator to reduce the pressure to no more

than 14 inches W.C. Failure to do this can result in

malfunction and damage to the appliance.

Important Notes for Gas Connection

The appliance and its individual gas shutoff valve must be

disconnected from the gas supply piping system during any

pressure testing of that system at test pressures in excess of

1/2 psi (3.5 kPa).

The appliance must be isolated from the gas supply piping

system by closing its individual manual shut-off valve during

any pressure testing of the gas supply piping system at test

pressures equal to or less than 1/2 psi (3.5 kPa).

All supply piping, except as noted, should use common

National Pipe Thread (N.P.T.). For all pipe connections use

an approved pipe joint compound resistant to the action of

LP gas.

This appliance is designed for use with NG gas or LP gas.

The gas pressure regulator is supplied with this appliance.

It must be installed in the gas way ahead of the manifold

entrance. It is pre-set for use with natural gas. To use it with

different gas it must be converted, as described in the Gas

conversion paragraph.

If at any time the appliance is to be used with a different

type of gas, all the conversion adjustments must be made

by a qualiﬁed technician before attempting to operate the

cooktop on that gas.

The gas should be supplied to the appliances pressure

regulator, at line pressure between 6 and 14 inches of

water column for NG, and between 11 and 14 inches of

water column for LP.

GAS REQUIREMENTS

NATURAL GAS WC

Manifold Pressure 5" (12.5 mb)

Min Line Pressure 6" (15 mb)

Max Line Pressure 14" (34.9 mb), .5 psi (3.5 kPa)

LP GAS WC

Manifold Pressure 10” (25 mb)

Min Line Pressure 11” (27.4 mb)

Max Line Pressure 14” (34.9 mb), .5 psi (3.5 kPa)

IMPORTANT

• NEVER REUSE OLD CONNECTORS WHEN INSTALLING

THIS COOKTOP.

To reduce the likelihood of gas leaks, apply teﬂon tape

or a thread compound approved for use with LP or

Natural gases to all threaded connections.

Apply a non-corrosive leak detection ﬂuid to all joints

and ﬁttings in the gas connection between the supply

line shut-off valve and the cooktop inlet.

Check for leaks!

Bubbles appearing around ﬁttings and connections

will indicate a leak. If a leak appears, turn off supply

line gas shut-off valve, tighten connections, turn on

the supply line gas shutoff valve, and retest for leaks.

Never test for gas leaks with an open ﬂame.

• NEVER TIGHTEN TO MORE THAN 35 ft lbs OF TORQUE.

4 - Gas Requirement

EN

10

Gas Connection

• Thread the appliances pressure regulator with 1/2”

male end connection both supplied with this appliance.

• Make the gas connection to the inlet of the pressure

regulator with 1/2” male pipe threads.

• Join the pressure regulator to the entrance threads

of the Gas Manifold with gasket supplied with this

appliance. The regulator is marked with a directional

arrow indicating correct direction of gas ﬂow. Ensure the

appliance regulator is installed with the arrow pointing

toward the gas manifold entrance and make sure the top

of the regulator is facing towards the cabinet front, easily

accessible through the cabinet doors.

• Connect a manual shut-off valve to the gas supply in an

accessible location for turning on or shutting off gas to

the appliance.

• Install a coupling between the regulator and the shutoff

valve to complete the connection.

• Assure all pipe joint connections are gas tight.

• Check alignment of valves after connecting the cooktop

to the gas supply to be sure the manifold pipe has not

been moved.

• A misalignment could cause the valve knob stem to rub

on the control panel, resulting in a gas leak at the valve.

If an oven is to be installed below this appliance connect gas

supply line as shown in ﬁgure consider the below cabinet

clearance.

ILLUSTRATIVE GAS SUPPLY PIPING

(NO OTHER APPLIANCE BELOW

COOKTOP)

BURNER BOX

(REAR OF APPLIANCE)

GASKET

FLARE UNION

ADAPTOR

APPLIANCE

PRESSURE

REGULATOR

ALL PIPE JOINTS

1/2" N.P.T.

GAS

MANIFOLD

SHUTOFF

VALVES

EN

11

FOR ALTERNATIVE PIPING METHODS TO CONNECT THE

APPLIANCE TO THE GAS SUPPLY, A TRAINED SERVICE MAN

OR GAS APPLIANCE INSTALLER MUST MAKE THE GAS SUPPLY

CONNECTION.

Leak testing of the appliance shall be conducted by the Installer

according to the Instructions given.

Unless prohibited by local codes or ordinances, a new A.G.A.

- Certiﬁed, ﬂexible metal appliance connector may be used to

connect this appliance to its gas supply.

The connector must have an internal diameter not less than

nominal 1/2” NPT pipe and be no more than 5 feet in length.

A 1/2” NPT x 1/2” ﬂare union adapter is required at each

end of the ﬂexible connector.

If a ﬂexible connector is used assure that both the appliance

pressure regulator and manual shut-off valve are joined

solidly to other permanent hard piping (either gas supply or

the appliance manifold) so as to be physically stationary. See

ﬁgure.

CAUTION

Do not attempt to attach the ﬂexible connector directly to an

external pipe thread.

Connection requires ﬂare union adapters.

For Massachusetts Installations:

1. Shut-off valve must be a “T” handle gas cock.

2. Flexible gas connector must not be longer than 36 inch.

3. Not approved for installation in a bedroom or a bathroom

unless unit is direct vent.

MANIFOLD

ENTRANCE

GASKET GASKET

FLARE

UNION

ADAPTOR

FLARE UNION

ADAPTOR 1/2" NPT

PIPE NIPPLE

ELBOW

1/2" NPT

PIPE NIPPLE

1/2" NPT PIPE

(STATIONARY

SUPPLY PIPE)

1/2" NPT PIPE

(STATIONARY

SUPPLY PIPE)

NO APPLIANCE

MOUNTED BELOW

THIS COOKTOP

WALL OVEN MOUNTED

IN CABINETRY BELOW

THIS COOKTOP

GAS

SHUT-OFF

VALVE

GAS

SHUT-OFF

VALVE

FLEXIBLE

APPLIANCE

CONNECTOR

5 FT. MAX

(1.52 m) MAX

()

FLEXIBLE

APPLIANCE

CONNECTOR

5 FT. MAX

(1.52 m) MAX

()

FLARE

UNION

ADAPTOR

FLARE

UNION

ADAPTOR

FLARE

UNION

ADAPTOR

APPLIANCE

PRESSURE REGULATOR,

SUPPLIED (OBSERVE

DIRECTIONALITY

OF GAS FLOW)

APPLIANCE

PRESSURE

REGULATOR,

SUPPLIED (OBSERVE

DIRECTIONALITY

OF GAS FLOW)

EN

12

Pressure Testing

The appliance must be isolated from the gas supply piping

system by closing its individual manual shut-off valve during

any pressure testing of the gas supply piping system at test

pressures equal to or less than 1/2 PSIG (3.5 kPa).

This appliance, as well as its individual shut-off valve, must

be disconnected from the gas supply piping system during

any pressure testing of the system at test pressures in excess

of 1/2 PSIG (3.5 kPa).

When checking appliance regulator function, make certain

pressure of natural gas supply is between 6 and 14 inches

of water column or, if converted for LP gas, between 11 and

14 inches.

THE PRESSURE TESTING SHOULD BE PERFORMED BY

MEANS OF THE INJECTOR THREAD ZONE

Gas test inlet

Thread

Pressure Test Method

• Remove grate and burner cap

• Remove aluminum gas spreader

• Temporarily remove the injectors

• Connect the pressure Test instrument into injector holder

thread zone (M6x0,75)

• Check if the cooktop has the correct pressure

• Fix the injector removed for testing and replace the parts

in the right position.

EN

13

5 - Electrical Requirements

General Information

This appliance must be supplied with the proper voltage

and frequency and connected to an individual, properly

grounded branch circuit, protected by a circuit breaker or

fuse having amperage as noted on the rating plate. We

recommend you have the electrical wiring and hookup of

your cooktop connected by a qualiﬁed electrician.

After installation, have the electrician show you where your

main cooktop disconnect is located. Check with your local

utilities for electrical codes which apply in your area. Failure

to wire your cooktop according to governing codes could

result in a hazardous condition.

If there are no codes, your cooktop must be wired and fused

to meet the requirements of the National Electrical Code,

ANSI/NFPA No. 70 - Latest edition.

You can get a copy by writing:

National Fire Protection Association

Battery march Park

Quincy. MA 02269

In Canada your cooktop must be wired and fused to meet

the requirements of the Canadian Electrical Code.

Be sure the installation of this product in a mobile home

conforms with the Manufactured Home Construction and

Safety Standard, Title 24 CFR, Part 3280.

If this standard does not apply, you must follow the standard

for Manufactured Home Installations, ANSI A225.1 and

Manufactured Home Installations, Sites and Communities

and ANSI/NFPA 501A or with local codes.

You can get a copy of the Federal Standard by Writing:

Ofﬁce of Mobile Home Standards HUD Building

451 7th Street, S.W.

Washington, D.C. 24010

LOCATION OF RATING PLATE

Electrical Connection

An adequate electrical supply and outlet must be used to

operate the electrical parts of your cooktop.

CAUTION

Electrical Grounding Instruction

Plug into a grounded 3 prong outlet. Do not remove ground

prong. Do not use an adapter. Do not use an extension cord.

Failure to follow these instructions can result in death, ﬁre, or

electrical shock.

IMPORTANT

FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE

PROPERLY GROUNDED.

The power cord of this appliance is equipped with a 3-

prong (grounding) plug which must be used with a properly

grounded 3-hole outlet with a standard 120 Volt, 60 cycle

AC household current. If you do not have a 3-hole grounded

outlet, have a qualiﬁed electrician change your old one.

A grounding adaptor will be needed to convert the old

one until the outlet can be replaced. This method is only

temporary, and a qualiﬁed electrician should test it to be

sure it meets requirements.

Electrical Requirements

Do not under any circumstances cut or remove grounding

prong from the cooktop cord.

GROUNDING PRONG

EN

14

WIRING DIAGRAM (4 ZONES)

2

3

4

5

2

3

4

5

TERMINAL

BLOCK

G N L

RE-IGNITER

SYSTEM

2

3

4

5

2

3

4

5

IN

OUT

WIRING DIAGRAM (5 ZONES)

1

2

3

4

5

1

2

3

4

5

TERMINAL

BLOCK

G N L

RE-IGNITER

SYSTEM

1

2

3

4

5

1

2

3

4

5

IN

OUT

EN

15

6 - Conversion for LP or NG Gas

Converting Appliance for Use with LP Gas

WARNING

Conversion is to be performed by a AUTHORIZED

SERVICER (or other qualiﬁed agency) in accordance

with the manufacturer’s instructions and all codes and

requirements of the authority having jurisdiction. Failure to

follow instructions could result in serious injury or property

damage.

The qualiﬁed agency performing this work assumes

responsibility for this conversion.

WARNING

Before proceeding with the conversion, shut off the gas

supply to the appliance prior to disconnecting the electrical

power

If this appliance should be converted for use with gas

LP (propane or butane), each of the following modiﬁcation

must be performed:

Gas conversion label (aluminium) to be placed on the back

of the appliance, near the data plate, after conversion has

been carried out;

Replace injector on (one ring ﬂame burners)

1. Remove the grates and burner cups.

2. Remove aluminum gas spreader.

3. Loosen injector by turning 9-32” (7 mm) nut driver counter

clockwise.

4. Install the injectors supplied with this appliances in the

appropriate burner. The injectors have small number

stamped on the side, this number codes the oriﬁce

diameter and its correct burner location (see ﬁgure on

page 17).

5. Turn clockwise to tighten (tighten to a torque of 15 to 20

inch-lbs).

6. Replace all parts following the reverse order.

7. Save the oriﬁces removed from the appliance for future

use.

Replace injectors on (two rings ﬂame burner)

1. Remove the grates and burner cups.

2. Remove aluminium gas spreader.

3. Remove the three screws of simmer gas spreader (1).

4. Remove the two screws of injector cover (2).

5. Loosen injector (A) by turning 9-32” (7 mm) nut driver

counter clockwise.

6. Loosen injector (B) by turning 9-32” (7 mm) box wrench

counter clockwise.

7. Install the injectors supplied with this appliances in the

appropriate burner. The injectors have small number

stamped on the side, this number codes the oriﬁce

diameter and its correct burner location (see ﬁgure of

the paragraph “Injectors position”).

8. Turn clockwise to tighten (tighten to a torque of 15 to 20

inch-lbs).

9. Replace all parts following the reverse order.

10. Save the injectors removed from the appliances for

future use.

After injectors replacement adjust the burner ﬂame (see Low

Flame Adjustment paragraph).

Check the appearance of each burner’s ﬂame at HILO

settings, if the ﬂame appear too large or too small make

sure that all steps were completed correctly.

Convert the pressure regulator on LP position following the

illustration.

EN

16

Converting Appliances for Use with NG Gas

If this appliance should be converted for use with gas NG

(natural gas), each of the following modiﬁcations must be

performed.

1. Replace all injectors following the step described on

page 15, observe the number stamped on the side,

this number codes the oriﬁce diameter and its correct

burner location (following the illustration of injectors

position).

2. Convert the pressure regulator on LP position (following

the illustration of pressure regulator conversion).

3. Adjust the burner ﬂame (see Low Flame Adjustment

paragraph).

Check the appearance of each burner’s ﬂame at HILO

settings, if the ﬂame appears too large or too small make

sure that all steps were completed correctly.

Pressure regulator conversion

The appliances is designed for use with NG gas or LP gas.

The gas pressure regulator is supplied. It must be installed

in the gas way ahead of manifold entrance. It is pre-set for

use with the gas supplied with the appliances. For use with

different gas must be converted.

For the pressure regulator conversion following the below

instructions:

• Disconnect all electrical power, at the main circuit breaker

or fuse box.

• Shut off the gas supply to the cooktop by closing the

manual shut-off valve.

• Adjust the pressure regulator, by following the instruction

(see ﬁgure)

1. Unscrew the regulator cap

2. Unscrew the plastic conversion plug from the cap turn

over and screw back (wide section away from cap for LP

and against cap for NG) see ﬁgures below.

3. Replace the cap regulator.

PRESSURE REGULATOR CONVERSION

Before replace the regulator cap.

Check the position of plug.

Suitable for the gas converted.

La page charge ...

Fulgor F4GK36S1 Guide d'installation

Ce manuel convient également à

Fulgor F4GK36S1 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents