Krups XP601050 Manuel utilisateur

Catégorie
Cafetières
Taper
Manuel utilisateur
XP6010
EN
FR
ES
www.krups.com
NC00023130-04
English . . . . . . . . . . . . . . . . . . p. 5
Français . . . . . . . . . . . . . . . . . p. 23
Español . . . . . . . . . . . . . . . . . p. 43
Réalisation : Espace Graphique
c
b
d
a
n
m
h1
h3
h4
h2
j
l
f
g
h
i
e
k
n
p
s
q
o
r
d2
d4
d3
d1
t
LOCKLOCK
WWW.KRUPS.COM
KR_ESPRESSO_XP6010_NAFTA_NC00023130-04 31/05/12 10:08 PageC1
1
3
2
LOCK
LOCK
LOCK
3
1
2
fig. 4
fig. 6
fig. 1 fig. 2
fig. 12
fig. 7
fig. 3
fig. 5
fig. 9
fig. 8
fig. 10
fig. 11
fig. 13 fig. 14
KR_ESPRESSO_XP6010_NAFTA_NC00023130-04 31/05/12 10:08 PageC4
CONTENTS
IMPORTANT WARNINGS.............................................................................................................................p. 6
INFORMATION ON PREPARING AN ESPRESSO...............................................................................p. 8
TECHNICAL FEATURES AND ACCESSORIES....................................................................................p. 8
PRODUCT DESCRIPTION...........................................................................................................................p. 9
MAIN FUNCTIONS..........................................................................................................................................p. 9
FEATURES .........................................................................................................................................................p. 10
CONTROL PANEL FEATURES ...................................................................................................................p. 11
BEFORE FIRST USE ......................................................................................................................................p. 11
USING THE APPLIANCE
1. ESPRESSO PREPARATION...................................................................................................................p. 13
2. HOT WATER FUNCTION ........................................................................................................................p. 15
3. STEAM FUNCTION ..................................................................................................................................p. 15
4. DESCALING................................................................................................................................................p. 16
5. AUTOMATIC STANDBY ...........................................................................................................................p. 18
6 CLEANING AND MAINTENANCE ........................................................................................................p. 18
7. TROUBLESHOOTING GUIDE..............................................................................................................p. 20
RECYCLING......................................................................................................................................................p. 21
MANUFACTURER’S WARRANTY...............................................................................................................p. 21
English
5
KR_ESPRESSO_XP6010_NAFTA_NC00023130-04 31/05/12 10:07 Page5
IMPORTANT WARNINGS
When using an electrical appliance, basic safety instructions must always be observed to
reduce the risks of fire, electric shock and injury, in particular the following:
1. Read the instructions for use in full before using for the first time.
2. Do not touch hot surfaces. Use the handles or buttons.
3. To protect from fires, electric shocks and injuries, do not immerse the power cord, plugs
or the machine in water or any other liquid.
4. This machine is not designed for use by children.
5. Children should be closely supervised when the electrical appliance is used in their
proximity. Store away from the reach of children.
6. This appliance is not intended for use by people (including children) without prior
experience or knowledge with the machine, unless they are supervised or have been
given instructions on how to use the appliance by a person responsible for their safety.
7. Children must be supervised to ensure that they do not play with the appliance.
8. Any contact with hot surfaces, hot water or steam can cause burns. Take care.
9. Take care when the steam spout is used as steam can cause burns.
10. Disconnect the appliance from the wall socket if it is not used for a few days and before
cleaning. Let the appliance cool down before installing or removing accessories and
before cleaning or storing.
11. All appliances are subject to strict quality controls. Practical tests are conducted on
randomly selected appliances, which may explain small marks or coffee remains in the
appliance before first use.
12. Do not use an electrical appliance whose power cord or plug is damaged, when the
appliance is not functioning correctly or is damaged in any way whatsoever. Return all
faulty appliances to the Krups Service Center as soon as possible so that it can be
inspected, adjusted or repaired.
13. To reduce the risk of injury, do not leave the cord hanging over the table or counter,
where it can be pulled on by a child or trip someone.
14. The cord must not hang over the table or counter or come into contact with hot surfaces.
15. Never pour cold water in the tank immediately after a brew cycle. Let the appliance cool
down between preparations.
16. Do not open the lid during coffee production.
GENERAL SAFETY RECOMMENDATIONS
n The use of accessory attachments not recommended by Krups may result in fire, electric
shock or injury to persons.
n Never immerse the appliance in water or any other liquid.
n Never operate the appliance with wet hands.
n Never place the appliance near to or on a source of heat and avoid the cord from
touching hot surfaces.
n Never use the appliance outdoors.
English
6
KR_ESPRESSO_XP6010_NAFTA_NC00023130-04 31/05/12 10:07 Page6
n Ensure that the mains voltage corresponds to that marked on the appliance’s name
plate.
n To prevent excessive load on the electricity network, do not connect other high
consumption appliances on the same circuit.
n Check that the power cord is in perfect condition before each use.
n Never pull the power cord or the appliance itself to disconnect the appliance.
n Never leave the appliance unsupervised when connected.
n If the power cord should become damaged, it must be replaced by a professional from
an Approved Service Center to avoid any danger.
n In the event of a fault or malfunction, do not try to repair the appliance yourself, leave
this to a professional from an Approved Service Center.
n This appliance has been designed for domestic use only. Any misuse of the appliance
cancels the guarantee and could release the manufacturer from any liability.
n Do not use appliance for other than intended use.
n To disconnect, stop the appliance with the button, then remove plug from wall outlet
SAVE THESE INSTRUCTIONS
NOTE
This appliance is designed for domestic use only. Any maintenance other than
cleaning and normal upkeep of the appliance by the owner should be performed by
Krups approved personnel only. Visit our website www.krupsusa.com in the USA
or www.krups.ca in Canada, or contact customer services at your nearest service
center. To reduce risks of fire and electric shock, do not dismantle the base of the
appliance. All repairs should be performed by Krups approved personnel only.
INSTRUCTIONS FOR A SHORT POWER CORD
A. A short power supply cord is provided to reduce risk resulting from becoming
entangled in or tripping over a longer cord. The use of an extension lead is not
recommended with this appliance.
B. if an extension lead is absolutely necessary, it may be used if care is exercised
in their use.
1) The extension lead must have at least the same rating as that of the machine.
2) The extension lead must not hang over the table or counter where it could be
pulled by a child or trip someone.
C. This appliance is equipped with a polarized plug (one blade is wider than the
other). To reduce the risk of electric shock, there is only one way to insert the
plug into the socket. If it does not fully fit into the socket, return it. If it still does
not fit, contact a qualified electrician. Under no circumstances should the plug
be changed.
In order to improve its products, Krups reserves the right to modify specifications without
prior notice.
English
7
KR_ESPRESSO_XP6010_NAFTA_NC00023130-04 31/05/12 10:07 Page7
INFORMATION ON PREPARING AN ESPRESSO
To obtain an espresso which is rich in aromas and creamy, the quality of the water, the temperature, the
variety of coffee, the roasting process, the fineness of the ground coffee, the dosage and the extraction
pressure are all determining elements.
Water
Always use clean fresh water and change the water every day. Water with a low mineral content is
preferred.
Temperature
For the first coffee or if multiple espressos are made during the day or if the machine is turned off between
each espresso, it is recommended that you dispense the equivalent of 1 cup of hot water as if you were
making a coffee but without using ground coffee.This helps preheat the group head, the filter holder, the
filter and the cup, allowing the coffee to maintain the ideal temperature for longer once in the cup.
Important
Do not pour a coffee into a cup at room temperature. This will cause the temperature of the espresso
to cool too quickly. It is recommended that you turn on your machine 10 to 15 minutes before making
the coffee and rest the cups on the cup warming plate. It heats up quickly and reaches a temperature
that is sufficiently high enough to heat the cups quickly and efficiently.
Coffee roasting
You can use any coffee variety for your espresso; the main thing is that it is fresh.
Coffee grinding
If the coffee is ground too finely, it will cause too much resistance to the hot water flow causing this to
overheat and “burn” the coffee, thus lending it a distinct bitterness. Too much resistance will also cause
the coffee to be dispensed drop by drop causing the foam not to form in the cup. If the coffee is ground
too coarsely it will provide no resistance to the water flow. The infusion time is therefore too short, resulting
in coffee that is not very creamy and does not release enough aromas.
TECHNICAL FEATURES AND ACCESSORIES
n Power: 1250 W
n Voltage: 120 V ~ 60 Hz
n Pump pressure: 15 bars
n Dimensions: L: 10.6 H: 12 W: 10
n Steel surface
n Product accessories: - 1 spoon
- One 1 cup filter
- One 2 cup filter
- One cleaning needle
English
8
KR_ESPRESSO_XP6010_NAFTA_NC00023130-04 31/05/12 10:07 Page8
PRODUCT DESCRIPTION
MAIN FUNCTIONS
n An unbeatable espresso:
- 15 bar high pressure pump
- Pre-wetting of the ground coffee
- Filters with pressurization chamber for increased crema.
n Impeccable water:
- Thermo block heating unit for an ideal, constant temperature
n Complete freedom of use:
- Compatible with ground coffee and all paper pods, both soft and compact
n Sophisticated design:
- 100% solid stainless steel cover
- Filter holder with professional dispensing spout
n Efficient cup warming plate:
- Large capacity holds up to 9 espresso cups.
- Solid stainless steel for quick and efficient pre-warming of cups.
n Automatic standby when appliance is not used for more than 30 minutes.
English
9
a Group head
b Stainless steel body
c Stainless steel cup warming plate
d Rotating control button
d1 : ESPRESSO function:
d2 : PENDING setting :
d3 : HOT WATER function
d4 : STEAM function
e Adjustable HOT WATER/STEAM nozzle
f Spout nozzle
g Frothing nozzle
h Control panel
h1 : TEMPERATURE light:
h2 : TEMPERATURE SELECTION button
- Espresso
- Hot water
- Steam
h3 : ON light
h4 : START/STOP button
i Removable water drip tray
j Stainless steel tray cover
k Tray water level indicator
l Stainless steel cup rest grill
m Removable water tank
n Filter holder
o Filter holder dispensing spout
p 1 cup espresso filter
q 2 cup espresso filter
r Espresso dosing spoon
s Ground coffee press
t Cleaning needle
KR_ESPRESSO_XP6010_NAFTA_NC00023130-04 31/05/12 10:07 Page9
FEATURES
The letters refer to the product description on page 9.
a. Group head
The group head enables the locking of the filter holder.
b. Stainless steel body
The body of your espresso machine is stainless steel for better quality and longevity.
c. Stainless steel cup warming plate
Warms cups quickly and efficiently, maintaining the ideal temperature longer.
d. Rotating control button
The rotating button activates the ESPRESSO, HOT WATER or STEAM function.
e. Adjustable HOT WATER/STEAM spout
The adjustable spout allows distribution of hot water or steam.
f. Spout nozzle
The spout nozzle enables the handling of the HOT WATER/STEAM spout without getting burnt.
g. Frothing nozzle
The frothing nozzle generates a smooth milk froth.
See page 15 for further information on using this nozzle.
i. Removable drip tray
The drip tray collects the overflow from the ESPRESSO. It is easily removable and should be checked
and emptied regularly.
k. Tray water level indicator
When a red signage is displayed on the indicator, the drip tray needs emptying.
l. Stainless steel cup rest grill
The perforated cup rest grill has markings for positioning cups.
m. Removable water tank
The tank can be removed from the machine for filling from the front of the machine (See section "Filling
the tank" page 12).
Comments:
- Make sure the water never exceeds the maximum level for the tank.
- Make sure the water in the tank never passes below the minimum water level.
Readjust the water level regularly.
n. Filter holder
The filter holder has an ergonomic handle. To make your espresso, place one of the filters in the filter holder
and then add the ground coffee. Position the filter holder on the group head to the far left then turn it to
the right to lock it into place.
English
10
KR_ESPRESSO_XP6010_NAFTA_NC00023130-04 31/05/12 10:07 Page10
p. 1 cup espresso filter
The cup size is identified on the bottom of the filter by the marking . This filter allows you to prepare 1
cup of espresso using ground coffee, a compact paper pod or a soft paper pod.
q. 2 cup espresso filter
The cup size is identified on the bottom of the filter by the marking . This filter allows you to prepare
2 cups of espresso using ground coffee. It cannot be used with 2 pods at the same time.
r. Espresso dosing spoon
Well-leveled, it allows you to measure the quantity of coffee required for a good espresso.
s Ground coffee press
The ground coffee press allows you to carefully tamp the coffee in the filter.
CONTROL PANEL FEATURES
The letters refer to the product description on page 9.
h1. TEMPERATURE light:
This red light indicates when your machine is ready to produce coffee, hot water or steam:
- Light on = coffee, hot water or steam is in progress (temperature not reached).
- Light off = coffee, hot water or steam is ready for dispensing (ideal temperature reached).
h2. TEMPERATURE SELECTION button:
For the water to remain at an ideal temperature for making your preparations, the the TEMPERATURE
SELECTION button must be positioned to the left for espressos or hot water and to the right for
steam .
h3. ON light
The green ON light comes on when you switch on the machine. It goes out when you switch off the
machine.
h4. START/STOP button
Turn the button to the right (I) to turn the machine on – the ON and TEMPERATURE lights" come on
right away – and to the left (O) to turn off.
BEFORE FIRST USE
n Open the machine and remove all the plastic bags, boxes and papers protecting the different parts.
Never leave the plastic bags in reach of children.
n Also remove any self-adhesive labels that may be on the product cover or any other information leaflets.
n Remove detachable parts and clean in warm soapy water. Do the same with the other accessories.
n Wipe the appliance body and staineless steel tray cover using a soft wet cloth.
IMPORTANT
Any action performed on the machine must be done with the power cord
disconnected. Never place parts or accessories in the dishwasher.
Never immerse the appliance, power cord or plug in any liquid.
English
11
KR_ESPRESSO_XP6010_NAFTA_NC00023130-04 31/05/12 10:07 Page11
n Ensure that all parts are completely dry before re-assembling:
n Place the cup rest grill on the water drip tray and slide into the housing.
n Reposition the water tank by pushing it backwards towards the edge of the machine.
Filling the water tank
To fill the tank:
n Remove the water tank by pulling it forwards using the central handle (fig.1).
n Fill the tank with fresh water without exceeding the maximum water level.
n Return the tank into its housing by sliding it along the cup rest grill (fig.2).
n Ensure that you have pushed it right to the end.
Draining and priming of the water circuit
Before using the machine for the first time it is imperative that you allow the water to circulate through all
of the appliance’s circuits to remove any possible air and for the pump to be activated.
With the water tank full:
n Connect the power cord
n Check that the rotating control button is set to PENDING (
) and that the TEMPERATURE
SELECTION button (h2) is at .
n Switch the machine on by turning the START/STOP button to the right to the (I) setting.
n The ON and TEMPERATURE lights come on straight away to indicate that the thermo block is
heating (approximately 1 minute).
NOTE
As long as the TEMPERATURE light is on, the temperature has not
been reached.
n Place a sufficiently large enough container under the HOT WATER/STEAM spout.
n When the TEMPERATURE light comes on, turn the rotating control button to HOT WATER
(fig.5).
n The pump starts working at a steady rate and the hot water flows through the spout. Proceed with
rinsing by circulating 1/4 of the full tank of fresh water through the spout.
n Stop the flow of water by simply returning the control button to PENDING (
) (fig.6).
n Empty the container and place it under the group head without using the filter holder.
n When the TEMPERATURE light comes on, turn the rotating control button to the ESPRESSO
function and proceed with rinsing by circulating 3/4 of the tank through the group head. (fig.3).
n Stop the flow of water by simply returning the control button to PENDING () (fig.4).
n The water circuit has now been drained and your machine is ready for use.
NOTE
A little steam may be released from the water tank. This is completely normal.
English
12
KR_ESPRESSO_XP6010_NAFTA_NC00023130-04 31/05/12 10:07 Page12
USING THE APPLIANCE
1. ESPRESSO PREPARATION
Espresso coffee is obtained by passing pressurized hot water through coffee grounds. The quality of the
taste depends on several factors: the type of coffee, the fineness of the ground coffee, the quantity of
ground coffee in the filter and the quality of the water…
The XP6010 espresso machine allows you to prepare a delicious espresso from ground coffee or a paper
coffee pod.
It is recommended that you turn the machine on 10 to 15 minutes before making your espresso
and pre-heat the cups on the cup warming plate. Your coffee will stay at the ideal temperature
longer in a cup that has been preheated.
A. Espresso made from ground coffee
n Choose the 1 cup filter or the 2 cup filter depending on the quantity of coffee required and
place in the filter holder. (fig.7).
n Fill the dosing spoon taking care to level it:
- 1-cup filter = 1 spoon of coffee (approximately 7 g)
- 2-cup filter = 2 spoons of coffee (approximately 14 g)
n Empty the contents of the spoon into the filter then gently shake to distribute the ground coffee
uniformly.
n Press down the ground coffee using the coffee press. If the coffee seems too light, press the coffee
more.
n If necessary, wipe the edge of the filter to remove any ground coffee that may be stuck and thus help
the filter holder lock into the group head.
B. Espresso made from paper pods
IMPORTANT
There are 2 types of paper pods:
- The "compact" pod = special espresso coffee packaged in a rigid pod (approx. 45 mm in
diameter) composed of 7 g of compacted ground coffee.
- "Soft" pod = pod measuring in general 55 to 60 mm in diameter. Since this type of pod is not
specifically designed for espresso machines, you will obtain a weaker espresso than with a
“compact” pod.
n Use the 1 cup filter and insert either a compact or a soft pod.
Important
Do not use the 2 cup filter with paper pods.
n Since the shape of the paper pods can differ from one brand to another, take care to center the pod in
the filter and push gently so that the sides fit.
IMPORTANT
If necessary, fold the sides of the paper pod inside the filter to prevent it from overhanging. This
will ensure that coffee will not leak outside the filter holder and prevent any damage.
English
13
KR_ESPRESSO_XP6010_NAFTA_NC00023130-04 31/05/12 10:07 Page13
C. Espresso function
Preparing the machine
n Check the water level in the tank and fill if necessary.
n Check that the rotating control button is set to PENDING (
) and that the TEMPERATURE
SELECTION button (h2) is at .
n Switch the machine on by turning the START/STOP button to the (I) setting.
n The ON and TEMPERATURE lights (h1) come on.
IMPORTANT
As long as the TEMPERATURE light (h1) is on, the ideal temperature for making your espresso
has not yet been reached. Wait until this light goes out.
n Insert the filter holder into the group head by aligning the handle with the marking "INSERTION" and
lock by moving the filter holder from left to right (fig.8).
n Firmly lock the filter holder into place and make sure it is properly inserted by pushing it to the right as
far as it will go.
n Place 1 or 2 cups (as necessary) on the cup rest grill and ensure that it/they are correctly positioned
under the coffee dispensing spout.
Coffee preparation
n It is imperative that you wait until the TEMPERATURE light goes out, indicating that the machine
has reached the optimum temperature for making coffee.
n Turn the rotating control button to ESPRESSO (fig.3).
n The pump is briefly activated to pre-wet the ground coffee and then stops for a few seconds and starts
again to dispense the coffee.
This pre-wetting process ensures even greater release of the aromas.
n When the required amount of coffee is reached, stop the flow of coffee by turning the rotating control
button to PENDING (
) (fig.4).
n Wait a few seconds until the surplus of water in the thermo block has been drained (until the “suction
noise” has stopped).
NOTE
A little steam may be released from the water tank. This is completely normal.
n Remove the cup(s) then unlock the filter holder by turning it from right to left until it can be released
from the group head.
n Drink the espresso immediately, so that its aromas and thick cream can be enjoyed to the full.
Cleaning the filter and filter holder
n Empty the filter using a small spoon or carefully tapping it against a surface so that any waste can be
collected.
n Remove the filter.
Important
The metal parts on the filter holder and filter are very hot.
n Rinse the filter and filter holder under hot water and dry.
English
14
KR_ESPRESSO_XP6010_NAFTA_NC00023130-04 31/05/12 10:07 Page14
2. HOT WATER FUNCTION
The production of hot water is ideal for preparing tea, infusions or pre-heating a container.
n Check the water level in the tank.
n Make sure that the frothing nozzle is securely fitted to the adjustable spout.
n Check that the rotating control button is set to PENDING () and that the TEMPERATURE
SELECTION button (h2) is at COFFEE/HOT WATER .
n Switch the machine on by turning the START/STOP button to the right to the (I) setting.
n The ON and TEMPERATURE lights will come on.
n It is imperative that you wait until the TEMPERATURE light goes out.
n Place a cup or bowl under the adjustable spout and make sure it is correctly positioned.
n Turn the control button to HOT WATER (fig.5).
n The hot water flows through the spout.
n When the desired quantity of water is reached:
- Turn the rotating control button to PENDING (
) to stop the flow of hot water (fig.6).
- The pump stops immediately and the spout circuit is closed.
IMPORTANT
It is possible that some steam may be released from the water tank. This is completely normal.
n You can now use the water collected to prepare your hot drink.
3. STEAM FUNCTION
Steam production is ideal for making the milk froth used in milk drinks (cappuccino, latte machiatto, hot
chocolate, etc.).
n Check the water level in the tank.
n Make sure that the frothing nozzle is securely fitted to the adjustable spout.
n Check that the rotating control button is set to PENDING ().
n Switch the machine on by turning the START/STOP button to the right to the (I) setting.
n The ON and TEMPERATURE lights come on.
n Turn the TEMPERATURE SELECTION button (h2) to STEAM .
IMPORTANT
For increased safety, the ESPRESSO function is blocked when the TEMPERATURE
SELECTION button (h2) is at STEAM or when the heating unit is too hot.
n It is imperative that you wait until the TEMPERATURE light goes out.
n Place a container or empty cup under the spout.
n Open the spout circuit by turning the control button to STEAM to dispense any remaining water
that may be in the circuit (fig.5).
n Turn the control button back to the left to PENDING (
) (fig.4).
n Pour the milk into a container and plunge the frothing nozzle into the container without touching the
bottom to prevent blocking the steam flow.
Advice
For a better result, use refrigerated milk, a cold stainless steel container and measure approximately
20 to 30 ml of milk per drink.
English
15
KR_ESPRESSO_XP6010_NAFTA_NC00023130-04 31/05/12 10:07 Page15
n Wait until the TEMPERATURE light goes out.
n Turn the control button back to STEAM (fig.5).
IMPORTANT
You will then hear an intermittent noise which is the pump jump starting. This is completely normal
and necessary for the steam production. A little steam may be released from the water tank. This
is completely normal.
IMPORTANT
To prevent blocking the flow of steam, the spout should not touch the bottom of the container.
n As soon as the milk begins to move, slowly return the frothing spout back to the surface with a circular
motion. Plunge the spout into the container once again this time with an increasing circular movement.
n Do this several times until the milk turns into a thick and creamy froth.
n When the required quantity of milk is reached, close the spout circuit by turning the control button to
PENDING (
) (fig.6).
IMPORTANT
It is possible that some steam may be released from the water tank. This is completely normal.
n You can now remove the container from the spout.
Important
- Following the production of steam, the spout and frothing nozzle are
extremely hot. Be careful of the risk of accidental burns.
- It is strongly recommended that the spout and its frothing nozzle is cleaned
every time milky froth is made (See section "Cleaning and maintenance"
page 18). This operation prevents any risk of spreading micro bacteria.
Important
To change to the ESPRESSO function after the production of steam, it is
imperative that hot water is passesd through the spout (See "Hot water
function" page 15) to force the temperature of the thermo block to fall. The
ESPRESSO function will remain blocked if this operation is not performed
first.
4. DESCALING
Reminder: The guarantee does not cover faulty appliances on which descaling was not performed
regularly.
Important
Regular descaling is recommended, on average every 2 months, (hard water with 3
to 4 espresso/day). For less frequent use (1 to 2 espresso/day), descaling should
be performed every 3 months.
English
16
KR_ESPRESSO_XP6010_NAFTA_NC00023130-04 31/05/12 10:07 Page16
Descaling of the ESPRESSO circuit
This operation is performed with the filter holder removed.
n Empty the water tank completely.
n Pour 500 ml of water into the tank with a packet of Espresso anti-scale agent available in stores or
250 ml of white vinegar mixed with 250 ml of water.
n Place a large container under the group head.
n Turn the appliance on and check that the rotating control button is set to PENDING (
)and that the
TEMPERATURE SELECTION button (h2) is at . Wait until the TEMPERATURE light goes out.
a) Activate the pump by turning the rotating control button (d) to the ESPRESSO function (fig.5)
to pump approximately 50 ml into the container, and then stop the pump by turning the rotating
control button back to PENDING (o) (fig.4).
b) Immediately turn the START/STOP button to O to switch off the machine (this must be done before
the suction noise for draining is triggered).
c) Let the solution rest for approximately 10 minutes in the case of the anti-scale agent (and 20 minutes
for the vinegar mixture) to let the liquid act in the heating unit and at the entrance to the group head.
n Repeat steps a) to c) twice.
Descaling of the SPOUT circuit
The descaling of the SPOUT circuit is very similar to that of the ESPRESSO circuit.
n Place the container under the adjustable spout and position correctly.
n Turn the appliance on and check that the rotating control button is set to PENDING (
) and that the
TEMPERATURE SELECTION button (h2) is at COFFEE/HOT WATER . Wait until the
TEMPERATURE light goes out.
n Turn the rotating control button to the right to select the HOT WATER function (fig.5).
n Let the antiscale agent flow through the spout for a maximum of 20 seconds.
n Stop the flow by turning the rotating control button (d) to PENDING (
) (fig.6).
n Immediately switch off the machine by turning the START/STOP button to O.
n Let the solution rest for the same length of time as for the ESPRESSO circuit.
n During this time, remove the remainder of the anti-scale agent contained in the tank and rinse thoroughly
with fresh water.
Rinsing of circuits
n Fill the tank with fresh water up to the maximum water level.
n Turn the appliance on and wait until the TEMPERATURE light goes out.
n Get a large container to collect the water.
n Start rinsing by circulating a full tank of fresh water as follows:
- 3/4 of the tank through the ESPRESSO circuit
- 1/4 of the tank through the frothing nozzle
IMPORTANT
Once you have let the equivalent of a tank of fresh water circulate through the 2 circuits you can
be sure that there is no anti-scale agent left in the tank nor any residue taste resulting from its use.
English
17
KR_ESPRESSO_XP6010_NAFTA_NC00023130-04 31/05/12 10:07 Page17
5. AUTOMATIC STANDBY
For safety and energy saving reasons, the XP6010 espresso machine is equipped with automatic standby:
n Your machine will automatically switch to standby when it has not been used for more than 30 minutes.
The TEMPERATURE light goes out and the ON light (h3) will remain lit but less bright. The main
electricity supply to your machine (thermo block heating included) is interrupted.
n To restart the machine, turn the START/STOP button to 0. Wait a few seconds and switch the machine
back on by turning the START/STOP button to (I).
6. CLEANING AND MAINTENANCE
To ensure that your KRUPS espresso Machine works for many years, we advise you to perform regular
maintenance.
Important
- Before any cleaning, disconnect the machine’s power cord and ensure that the
machine is cold.
- None of the machine’s parts can be put in the dishwasher.
Regular cleaning of filters and filter holder
n After each use, clean the filter and the filter holder under warm water.
n Regularly check that the sieves at the bottom of the filters are not blocked. If necessary, use a fine
needle (not supplied) to unblock the holes. You can also wipe the upper surface of the sieves using a
synthetic brush and run the filters under warm water to remove any dirt.
Clean the filters thoroughly
If you notice a problem dispensing coffee, it may be that the filter is blocked. In this case, clean thoroughly:
n Using a cross recess unscrew the central screw.
n Remove the stainless steel sieve.(fig.9).
n Clean all the parts in warm water.
n Hold to the light to check that there is no residue blocking the holes. If so, clean more thoroughly taking
care to remove any particles using a synthetic brush or a fine needle.
Important
Ensure that the different parts are dry before assembling:
place the sieve in the filter and tighten the screw.
Cleaning the group head
n The base of the group head must be cleaned regularly using a non-abrasive cloth soaked in water. This is
to remove all remaining coffee grounds from the sieve and in the filter holder housing system.
n Residual coffee grounds can also get blocked in the group head’s peripheral cylinder. In this case, this can
be removed using a small fine object which is not pointed or a toothpick.
IMPORTANT
You are advised to operate your machine regularly with the filter holder in place but without coffee,
to remove any coffee residue.
English
18
KR_ESPRESSO_XP6010_NAFTA_NC00023130-04 31/05/12 10:07 Page18
Cleaning the adjustable spout and frothing spout
It is highy recommended that you clean the spout and its frothing nozzle after each time you froth milk.
Important
Ensure that the spout and its nozzle have cooled down before performing any
maintenance.
n Remove the frothing nozzle from the spout by turning it fully then pull the part to release (fig.10).
n Dip the frothing nozzle in very hot water to ensure that any milk residue is completely removed.
IMPORTANT
If any of the milk froth has dried up around the frothing nozzle, dip it in a container of water overnight
to soften the residue.
n Clean the outside of the plastic tube of the nozzle with hot water.
n If necessary, unblock the internal steam duct by inserting the needle supplied (t) into the nozzle hole and
running some hot water or steam through the plastic tube (See sections "Hot water function" page 15
or "Steam function" page 15).
n Ensure that all parts are completely dry.
n We also recommend that you use this needle to unblock the holes in the filters and the small hole at
the top of the detachable metal steam foam nozzle (fig 11).
n Carefully fit the special cappuccino nozzle by positioning the pins in the holes and rotating them anti-
clockwise until they lock into place (fig.12).
IMPORTANT
These operations are essential to prevent any risk of spreading micro bateria.
Cleaning the water tank
n Remove and clean the water tank every day. Rinse with clear water and re-position ensuring that it is
correctly lodged in its housing.
n If a layer of limescale should form on the tank walls, descale using a mixture of water and white vinegar.
Leave to rest for 1 hour.
n Wipe with a non-abrasive sponge and rinse thoroughly.
Cleaning the cup rest grill and drip tray
n Remove the drip tray by sliding it forwards (fig.13).
n Remove the cup rest grill by lifting upwards (fig.14).
n Clean the cup rest grill and drip tray with warm soapy water.
n Rinse and dry thoroughly.
n Clean the tray’s stainless steel cover using a non-abrasive slightly damp cloth. Dry.
IMPORTANT
The water level indicator can be removed and re-attached using the clips.
Cleaning the appliance body, the cup warming plate
These parts of the appliance are cleaned using a non-abrasive and slightly wet cloth.
Important
Take care not to allow water on the control panel.
Any other servicing should be performed by an authorized service representative.
English
19
KR_ESPRESSO_XP6010_NAFTA_NC00023130-04 31/05/12 10:07 Page19
7. TROUBLESHOOTING GUIDE
English
20
Problems Probable causes Solutions
The appliance does
not work.
The power supply has been
cut off.
Check that there is current at the socket.
The machine is not on.
Activate the START/STOP button and check that
the temperature light is flashing.
The heating unit
does not heat up.
The machine is on
automatic standby.
Exit standby mode by activating the
START/STOP button.
Coffee, hot water or
steam is not
dispensed.
The water tank is empty
Important: if it becomes
empty during operation, the
pump becomes very noisy.
Stop the function
immediately or switch the
machine off.
Fill the water tank. See the “Draining the water
circuit” paragraph to restart the pump.
The water tank is not
positioned correctly.
Remove the tank and reposition it correctly.
The coffee is ground too
finely.
Check your grind setting on your grinder and
readjust it to a coarser grind.
There is too much coffee in
the filter.
Use the quantity indicated in the instructions.
The filter is blocked.
Dip the filter in soapy water to clean it; gently
scrub to remove superficial dirt. Use a fine needle
to remove any dirt, limescale and rinse under clear
water.
If necessary, perform more thorough cleaning
(See section “Thorough cleaning" on page 18).
The heating unit is still too
hot following steam
production.
It is imperative that you let the hot water flow
through the spout to lower the temperature
of the thermo block.
The appliance has
limescale.
Completely descale the appliance (See section
“Descaling” on page 16).
The coffee flows
through the panels
on the filter holder.
The filter holder is not
securely attached to the
group head.
Tighten the filter holder to the group head.
Locking of the filter holder will get easier after the
first uses.
The edges of the paper
pods overlap the filter.
Center the pod and fold the edges inside the
filter.
The joint for the group head
is worn.
Get a professional from an Approved Service
Center to replace the joint.
KR_ESPRESSO_XP6010_NAFTA_NC00023130-04 31/05/12 10:07 Page20
RECYCLING
Let’s help protect the environment!
Your appliance contains various materials that can be recovered or recycled.
Take it to a recycling collection centre or an approved service centre for recycling
MANUFACTURER’S WARRANTY
: www.krups.com
With a strong commitment to the environment, most of Krups products are
repairable during and after the warranty period. Before returning any defective
products to the point of purchase, please call Krups consumer service directly
at the phone number below for repair options.
Your help to sustain the environment is appreciated!
The Warranty
This product is guaranteed by Krups for a period of 2 years against any manufacturing defect in
materials or workmanship, starting from the initial date of purchase.
The manufacturer's warranty by Krups is an extra benefit which does not affect consumer's
Statutory Rights.
The Krups warranty covers all costs related to restoring the proven defective product so that it
conforms to its original specifications, through the repair or replacement of any defective part
and the necessary labor. At Krups’s choice, a replacement product may be provided instead of
repairing a defective product. Krups’s sole obligation and your exclusive resolution under this
warranty are limited to such repair or replacement.
Conditions & Exclusions
The Krups warranty only applies within USA, Canada & Mexico, and is valid only on presentation
of a proof of purchase. The product can be taken directly in person to an authorized
service centre or must be adequately packaged and returned, by recorded delivery (or equivalent
method of postage), to a Krups authorized service centre. Full address details for each country’s
authorized service centre are listed on the Krups website (www.krups.com
) or by calling the
appropriate telephone number listed below to request the appropriate postal address.
Krups shall not be obliged to repair or replace any product which is not accompanied by a valid
proof of purchase.
English
21
Problems Probable causes Solutions
The coffee or hot
water tastes bad.
The heating unit or spout
circuit has limescale.
Descale the appliance.
The appliance was not
rinsed properly after
descaling.
Rinse again thoroughly.
The water used is of
insufficient quality.
Change water. Water with a low mineral content
is preferable (pH 7).
The coffee color
does not look right
The coffee is not fresh. Replace with fresh coffee.
The coffee grounds are too
coarse.
Replace with finer coffee grounds.
The cup is too cold. Pre-heat the cup.
KR_ESPRESSO_XP6010_NAFTA_NC00023130-04 31/05/12 10:07 Page21
This warranty will not cover any damage which could occur as a result of misuse, negligence,
failure to follow Krups instructions, use on current or voltage other than as stamped on the
product, or a modification or unauthorized repair of the product. It also does not cover normal
tear and wear, maintenance or replacement of consumable parts, and the following:
-using the wrong type of water
-scaling (any de-scaling must be carried out according to the instructions for use);
-ingress of water, dust or insects into the product;
-mechanical damages, overloading
-damages or bad results due to wrong voltage or frequency
-accidents including fire, flood, lightning, etc
-professional or commercial use
-damage to any glass or porcelain ware in the product
This warranty does not apply to any product that has been tampered with, or to damages incurred
through improper use and care, faulty packaging by the owner or mishandling by any carrier.
The Krups manufacturer's warranty applies only for products purchased and used in USA, Canada
& Mexico. Where a product purchased in one country and then used in another one:
a) The Krups guarantee duration is the one in the country of usage of the product, even if
the product was purchased in another listed country with different guarantee duration.
b) The Krups guarantee does not apply in case of non conformity of the purchased product
with the local standards, such as voltage, frequency, power plugs, or other local technical
specifications
c) The repair process for products purchased outside the country of use may require a
longer time if the product is not locally sold by Krups
d) In cases where the product is not repairable in the new country, the Krups guarantee is
limited to a replacement by a similar product or an alternative product at similar cost,
where possible
.
Consumer Statutory Rights
This Krups manufacturer's warranty does not affect the statutory rights a consumer may have or
those rights that cannot be excluded or limited, nor rights against the retailer from which the
consumer purchased the product. This warranty gives a consumer specific legal rights, and the
consumer may also have other legal rights which vary from State to State or Country to Country
or Province to Province. The consumer may assert any such rights at his sole discretion.
Additional information
Accessories, Consumables and end-user replaceable parts can be purchased, if locally available,
as described in Krups internet site.
: www.krups.com
CANADA
GROUPE SEB
CANADA
345 Passmore Avenue
Toronto, ON
M1V 3N8
MEXICO
Groupe SEB MEXICO
S.A. de C.V.
Goldsmith 38 Desp.
401 Col. Polanco
Delegacion Miguel
Hildalgo
11 560 Mexico D.F.
MEXICO
U.S.A.
GROUPE SEB USA
2121 Eden Road
Millville, NJ 08332
1-800-418-3325 01800 1128325 800-526-5377
English
22
KR_ESPRESSO_XP6010_NAFTA_NC00023130-04 31/05/12 10:07 Page22
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59

Krups XP601050 Manuel utilisateur

Catégorie
Cafetières
Taper
Manuel utilisateur

dans d''autres langues